PDF User Manual

Super 130.2
Super 140.2
Super 140.2 Plus

User Guide

Super 130.2
Super 140.2
Super 140.2 Plus

3

Index

 1  Safety precautions and warnings .............................3

 2  Description...........................................................4

 3  Before you start using your pressure washer ............5

 4  Operating your pressure washer ..............................6

 5  Fields of Application

    and Working Methods .......................................... 10

 6  After using your pressure washer .......................... 12

 7  Maintenance ....................................................... 13

 8  Trouble Shooting ................................................. 14

 9  Further information ............................................. 15

 10  EC Declaration of Conformity ................................ 17

1  Safety Precautions and Warnings

Before start-

ing up your 

high-pressure 

washer for the 

fi rst time, this 

instruction manual must 

be read through carefully. 

Save the instructions for 

later use.

Safety instruc-

tions marked 

with this symbol 

must be ob-

served to prevent danger to 

persons.

This symbol is 

used to mark 

safety instruc-

tions that must 

be observed to 

prevent damage to 

the  machine and its per-

formance.

This symbol 

indicates tips 

and instructions to simplify 

work and to ensure safe 

operation.

Do not let children or peo-

ple who have not read the 

instruction manual ope rate 

the machine.

Before starting up your ma-

chine please check it care-

fully for any defects. If you 

fi nd any, do not start up 

your machine and contact 

your Gerni  distributor.

Especially check:

 The insulation of the 

electric cable should be 

faultless and without any 

cracks. If the electric 

cable is damaged, an au-

thorized Gerni  distributor 

should replace it.

WARNING!

 High pressure jets can be 

dangerous. Never direct 

the water jet at persons, 

pets, live electrical equip-

ment or the machine 

 itself.

  Never try to clean clothes 

or footwear on yourself 

or other persons.

  Hold the spray lance fi rm-

ly with both hands. The 

spray lance is  affected by 

a thrust of up to 16.4 N 

during ope ration.

 The operator and anyone 

in the immediate vicin-

ity of the site of clean-

ing should take action to 

protect themselves from 

being struck by debris 

dislodged during opera-

tion. Wear goggles during 

operation.

  Never use the machine 

in an environment where 

there could be a danger 

of explosion. If any doubt 

arises, please contact the 

local  authorities.

  It is not allowed to clean 

 asbestos- containing sur-

faces with high pressure.

This high pressure wash-

er must not be used at 

tempe ratures below 0°C.

Symbols used to mark 
 instructions

4

Extension cables should be 

of a watertight construction 

and comply with the below-

mentioned requirements 

for length and cable dimen-

sions.

1.0 mm² 

max. 

12.5 m 

1.5 mm² 

max.  

20 m

2.5 mm² 

max. 

30 m

  Cable connections should 

be kept dry and off the 

ground.

Mains power connection

The following should be ob-

served when  connecting the 

high pressure washer to the 

electric installation:

  Only connect the machine 

to an installation with 

earth connection.

  The electric installation 

shall be made by a certi-

fi ed electrician.

  It is strongly recom-

mended that the electric 

supply to this machine 

should include a residual 

current device (GFCI).

Water connection

Connection to the public 

mains  according to regula-

tions.

IMPORTANT! Only use 

water without any impu-

rities. If there is a risk of 

running sands in the inlet 

water (i.e. from your own 

well), an additional fi lter 

should be mounted.

Repair and maintenance
WARNING! 

Always remove 

the electric plug from the 

socket before carrying out 

maintenance work on the 

machine.

Safety devices

Locking device on spray 

gun (7a) (see foldout at the 

end of this manual):

The spray gun features a 

locking device. When the 

pawl is activated, the spray 

gun cannot be ope rated. 

Thermal sensor:

A thermal sensor protects 

the motor against over-

loading. The machine will 

restart after a few minutes 

when the thermal sensor 

has cooled.

Pressure safety device

An integrated hydraulic 

safety valve protects the 

system from excessive 

pressure.

2 Description

This high-pressure washer 

has been developed for do-

mestic use within: 

-  Car, motorbike, boat, 

caravan, trailer, patio/

drive/fl ag stones, wood-

work, brickwork,    barbe-

cue, garden furniture,  

lawn mower

Section 5 describes the use 

of the high-pressure washer 

for vaious cleaning jobs.

Only use the high-pressure 

washer for purposes de-

scribed in this manual. 

The safety precautions 

must be observed to pre-

vent damage to the ma-

chine, the surface to be 

cleaned or severe personal 

injuries.

2.1 Application

Never let any persons 

stand under the product 

when stored on the wall.

WARNING!

Inadequate extension 

 cables can be dangerous. 

Cables on drums should 

always be completely un-

winded to prevent the cable 

from overheating.

5

2.2 Operation elements

and model survey

See illustration at the end 

of this manual.

 1 Start/stop switch

  2  Water inlet (with fi lter)

  3  High pressure connec-

tion (only models with-

out hose reel)

  4  High pressure hose

 5 Electric cable

  6  Click & Clean spray 

lance

  7  Spray gun with lock

  8  Click & Clean Tornado

®

PR nozzle

  9  Click & Clean Power-

speed

®

 nozzle

 10 Click & Clean foam 

sprayer

 11 Nozzle cleaning tool

 12 Trolley handle (telescop-

ic handle)

 13 Hose reel (not standard)

 14 Hose hook

 15 Model tag

 16 Quick coupling

 17 Button for telescopic 

handle

 18 Turnable cable hook

Specifi cations:

 See model 

tag (15) of machine.

Sound pressure level meas-

ures in accordance with 

ISO 3744 EEC directive 

2000/14/EEC:  L

pA 

= 69,9 

dB(A), L

WA 

= 84 dB(A). 

We reserve the right to al-

ter the specifi cations.

3  Before you start using your 

 pressure 

washer

3.1 Mounting of 

trolley handle and 

hose hook (standard 

models)

that the handle is mount-

ed as illustrated. Mount 

screws with nuts (make 

sure that the screws go 

through handle as well as 

tube).

2. Mount the hose hook 

(14) on the machine (2 

screws). Note: the hose 

hook can be mounted on 

the front as well as on 

the back. Front position is 

to be used if the product 

is used together with a 

special wall hook for wall 

storage.

3.2  Mounting of hose 

reel handle (models 

with hose reel)

1. Click the hose reel handle 

on to the trolley handle 

(no screws).

1. Push down the trolley 

handle (12) over the two 

metal tubes. Make sure 

6

3.3  Mounting of quick   

coupling

1. Screw the quick coupling 

(16)tight on to the water 

inlet (2).

Note:

 The inlet fi lter must 

always be fi tted in the wa-

ter inlet pipe to fi lter out 

sand, lime stone and other 

impurities as these will 

damage the pump valves. 

Caution:

 Failure 

to fi t the fi lter 

will invalidate 

the guarantee.

4  Operating your pressure      

washer

4.1  Connection of high 

pressure hose (mo-

dels without hose 

reel) 

1. Mount the high pressure 

hose on the outlet (3).

3.4  Mounting of high 
 pressure 

hose

Attach the high pressure 

hose (4) to the spray gun 

(7).

Detach the high pressure 

hose by pressing the button 

(A).

7

4.2  Mounting of spray 

lance and Click & 

Clean  nozzles

2. Attach the nozzle. 

Warning:

 When 

attaching the 

Click & Clean 

nozzles, the 

button on the side 

of the spray lance should 

come out again.  

Note: 

The Torna-

do

® 

PR  nozzle 

and the foam 

sprayer feature a swivel 

lock, which must be po-

sitioned in the hole in the 

Click & Clean spray lance.  

Press the button to detach 

the Click & Clean nozzle.

1. Push the spray lance (6) 

into the spray gun (7) 

and twist it on.

Note: 

The spray lance (6) 

has a built-in low pres-

sure nozzle that can be 

used for fl ushing away 

dirt.

4.3 Water connection

An ordinary 1/2" garden 

hose of 

min. 10 m

 and 

max. 

25 m

 will be suitable.

NOTE: Connection to the 

public mains  according to 

regulations.

IMPORTANT! Only use 

water without any impu-

rities. If there is a risk of 

running sands in the inlet 

water (i.e. from your own 

well), an additional fi lter 

should be mounted.

1. Let the water run through 

the water hose before 

connecting it to the ma-

chine to prevent sand 

and dirt from penetrating 

the machine.

Note:

 Check 

that the fi lter 

is fi tted in the 

water inlet pipe and that 

it is not clogged up.

2. Connect the water hose 

to the water supply by 

means of the quick con-

nector (inlet water, max. 

pressure: 10 bar, max. 

temperature: 50°C).

3. Turn on the water.

8

4.5  Start and stop of the 

machine (when con-

nected to a water 

supply)

The spray lance is affected 

by a thrust during operation 

- therefore always hold it 

fi rmly with both hands. IM-

PORTANT: 

Point the nozzle 

at the ground.

1. Check that the machine 

is in upright position.

 NOTE: 

Do not place the 

machine in tall grass!

2. Release the trigger lock.

3. Activate the trigger of 

the spray gun and let the 

water run until all air has 

escaped from the water 

hose.

4. Turn the start/stop switch 

(1) to position "

I

".

5. Activate the trigger of the 

spray gun.

Always adjust the distance 

and thus the pressure of 

the nozzle to the surface, 

which is to be cleaned. 

Do not cover the machine 

 during operation. 

Note:

 If the 

machine is left 

or not used 

for 5  minutes, it must be 

switched off on the start/

stop switch "

O

" (1):

1. Turn the start/stop switch 

to position "O".

2. Disconnect the electrical 

plug from the socket.

3. Shut off the water supply 

and activate the trigger 

to relieve the machine of 

pressure.

4. Lock the spray gun.

When releasing the trigger 

of the spray gun, the ma-

chine automatically stops. 

The machine will start again 

when you re-activate the 

spray gun.

4.4 Telescopic handle

The machine features a 

tele scopic handle. To raise 

or lower the  handle, press 

the knob and move the 

handle upwards or down-

wards. When a click is 

heard, the handle is in right 

position. 

fi lter if the water contains 

impurities.

2. Turn the start/stop switch 

to position "

I

".

3. Activate the trigger of 

the spray gun with lance 

and nozzle removed and 

let the water run, until 

the air has escaped from 

the water hose and the 

pump.

4. Mount spray lance and 

 nozzle.

The washer can take in wa-

ter from a rain water tank 

or  bucket as an example. 

The hose for the water sup-

ply must not be too long, 

approx. 5 m.

Make sure that the water 

tank is not placed on a low-

er level than the machine.

1. Place the other end of the 

water hose in the water 

tank. Use an external 

4.6  Start the machine 

(when connected 

to open containers 

(suction mode))

9

4.7 Pressure regulation 

on the TORNADO

®

PR-nozzle

The pressure can be regu-

lated on the TORNADO

®

 PR 

nozzle.

4.8 Stationary use

If mounting a special wall 

hook (not standard), the 

pressure washer can be 

used as a stationary solu-

tion meaning that it can be 

operated while hanging on 

the wall.

Only mount the wall hook 

on a sturdy wall. Adjust 

the length of the screws 

and size of rawlplugs to the 

type of wall. 

On the wall hook garden/

rim brush (a) foam sprayer 

(b),  Click & Clean brush (c) 

and Click & Clean nozzles 

(d) can be stored. 

Important: 

The 

bearing capac-

ity of the wall 

hook is max. 30 

kg.

A

C

B

D

Lavtryk 

Højtryk 

High pressure

Low pressure

10

5  Fields of application and 

 working 

methods

5.1 General 

Effi cient high presure cleaning is achieved by following a 

few guidelines, combined with your own personal experi-

ence of specifi c cleaning tasks. Accessories and deter-

gents, when correctly chosen, can increase the effi ciency 

of your pressure washer. Here is some basic information 

about cleaning.

5.1.1 Detergent and foam

Foam or detergent should be applied onto dry surfaces so 

that the chemical product is in direct contact with the dirt. 

Detergents are applied from bottom to top, for example 

on a car bodywork, in order to avoid "super clean" areas, 

where the detergent collects in higher concentration and 

streams downwards. Let the detergent work for several 

minutes before rinsing but never let it dry on the surface 

being cleaned. 

Note: 

It is important that the detergents do 

not dry up. Otherwise the surface that has to be cleaned 

can be da maged.

5.1.2 Mechanical effect

In order to break down tough layers of dirt, additional 

mechanical effect may be required. Special wash brushes 

offer this supplementary effect that cuts through dirt (es-

pecially by car washing).

11

5.2  Typical fi elds of application

Below you will fi nd a description of a lot of cleaning tasks which can be solved by a pres-

sure washer from Gerni in association with accessories and detergents.

Task

Accessories ‘Click 

& Clean’ 

Cleaning method

Car

Car nozzle, 
auto brush, 
underchassis  nozzle,

Foam sprayer, 

Neutral car wash

1. Apply neutral car wash with the foam sprayer. Always start from 

the bottom and work upwards. Let neutral car wash act for at 
least 5 min.

2. Wash the car with the car nozzle, which has been optimized for 

quick and gentle cleaning of enamelled surfaces (the jet is wider 
and not so sharp). Start at the front of the car and work back-
wards to avoid water from penetrating by the door mouldings. 

3. Use the brush for removal of traffi c fi lm which is not removed by the 

nozzle. If the car is very dirty, apply neutral car wash again. 

4. Attach the undercarriage nozzle and clean undercarriage and 

wheel arches.  

5. Remove water from the surface of the car with the squeegee on 

the car brush. Make sure that all grains of sand etc. have been 
removed before using the squeegee. Wipe with a wash leather 
where the squeegee cannot reach.

Rims, alu-

minium

Rim brush,
auto nozzle,
 atomizer,
 alloy cleaning agent

Apply alloy cleaning agent with an automizer. Let it act for approx. 

5 min. and wash with the rim brush. For steel rims, use neutral car 
wash. Use the foam sprayer and wash with rim brush.

 Be careful!  The high pressure jet may damage the tyres. 

Flag-

stones,

concrete 

fl oors 
and other 
hard sur-
faces

Powerspeed

®

nozzle, 
neutral detergent,
 Patio  Cleaner

Wash towards outlets or the like. On surfaces with moss or al-

gae you may start by applying Neutral detergent with the foam 
sprayer. Wash before the soap dries. Another more effective and 
quicker method is to use the Patio Cleaner. Thus you will also 
avoid splashes.

Garden 

furniture, 
wood 

Wood Cleaner
Garden brush

Apply Wood Cleaner and wash before the soap dries. 
NOTE: Use the garden brush to clean off the dirt.

Brick-

work,

Wood 

work

Powerspeed

®

nozzle, 
neutral detergent,
 Patio  Cleaner

Same method as for fl agstones, but be careful - bad joints and 

wood may be damaged by high pressure. You may choose only 
to use the Tornado

®

 nozzle. Adjust the distance (pressure) to the 

quality of the joints and the wood. Patio Cleaner can also be used 
on vertical surfaces. 

Gutter

Underchassis  spray 

lance

Wash the gutter with the nozzle. Always wash towards     

downpipes. Beware not to spray under the roofi ng.

Cleaning 

of drain 
pipes, 
outlets, 
down 
pipes etc.

Tube cleaner

Push the tube cleaner approx. ½ m (to mark) into a tube or drain 

and activate the trigger of the spray handle. The nozzle opening  
turning backwards will pull the cleaner through the tube. The 
 nozzle will break down the „plug“ and fl ush the dirt backwards.

Rust, 

paint

Water/sandblasting 

equipment

Mount the water/sand blasting equipment and rust and paint   

is effi ciently and quickly removed. Beware not to damage the sur-
face to be sandblasted.

Green-

house

Tornado

®

 PR nozzle

brush, neutral de-

tergent

Wash with high pressure and maybe a brush. You may use neutral 

detergent to remove moss and algae.

Garden 

tools, 
lawn 
mower

Tornado

®

 PR  nozzle, 

Powerspeed

®

 nozzle, multiangle 
adaptor, degreaser

Rinse the worst dirt off with the nozzle. Apply degreaser with 

the foam sprayer and let it act for approx. 5 min. Wash with the 
 nozzle. You may use the multiangle adaptor for hard to get at 
 areas to avoid splashing.

12

6  After using your pressure     

washer

6.2  Winding up of elec-

tric cable and high 

pressure hose 

ways be carefully  wound 

up.

1. Wind up the electric cable 

on the appropriate hooks. 

A built in clip secure the 

cable (1).

  The lower hook can be 

turned to release the 

electric cable. 

2. The high pressure washer 

comes in two models: A) 

with hook for storage of 

high pressure hose (14) - 

B) with a hose reel (13).

6.1  Storing the washer

The machine should be sto-
red in a frost-free room!

Pump, hose and accessories 

should always be emptied 

of water prior to storing as 

follows:

1. Stop the machine (turn 

the start/stop switch 

(1) to position “

O

” and 

detach water hose and 

 accessory.

2. Restart the machine and 

activate the trigger. Let 

the machine run until no 

more water runs through 

the spray gun.

3. Stop the machine, unplug 

and wind up hose and 

cable. 

4. Place spray handle, 

 nozzles and other acces-

sories in the holders of 

the machine.

Should the machine by 

mistake be frozen, it will 

be necessary to check it for 

damage.

NEVER START-UP A FRO-

ZEN MACHINE.

Frost damages are 

not  covered by the 

 guarantee!

6.3 Storage of 

 accessories

The standard accesso-

ries (spray gun (f), spray 

lance (a), nozzles (b) foam 

sprayer (c)) can be stored 

on the pressure washer.

The nozzle cleaning tool (d) 

and a Click & Clean brush 

(e) can also be stored on 

the  product.

To avoid accidents, the 

electric cable and the high 

pressure hose should al-

a

b

c

d

e

f

a + f

13

WARNING! Always dis-

connect the electrical plug 

from the socket prior to 

maintenance or cleaning. 

To ensure a long and 

problem free working life, 

please take the following 

advice:

 Wash out water hose, 

high pressure hose, 

spray lance and accesso-

ries before mounting.

 Clean the connectors of 

dust and sand. Make sure 

that no sand or dirt is 

blocking the movement 

of the button on the Click 

& Clean spray lance.

 Rinse the detergent 

spraying attachment after 

use.

 Clean the nozzles.

Any repair should always 

be made in an  authorized 

workshop with original 

spare parts.

7 Maintenance 

7.1  Cleaning of water 

 inlet 

fi lter

Clean the water inlet fi lter 

regularly once a month or 

more frequently according 

to use. Carefully loosen the 

fi lter with a pair of pliers 

and clean it. Check that it 

is intact before re-mounting 

it. 

The inlet fi lter must always 

be fi tted inside the water 

inlet pipe to fi lter out sand, 

limestone and other impuri-

ties, as they will damage 

the pump valves.

CAUTION: Failure to fi t 

the fi lter will invalidate the 

guarantee.

7.2  Cleaning of nozzle 

A clogging up in the noz-

zle causes a pump pressure 

which is too high. This is 

why cleaning is required 

immediately.

1. Stop the machine and 

disconnect the  nozzle. 

2. Clean the nozzle.

 IMPOR-

TANT: 

The cleaning tool 

(11) should only be used 

when the nozzle is de-

tached!

3. Flush the nozzle back-

wards with water.

14

8 Trouble 

Shooting

To avoid unnecessary disappointments, you should check the following before contacting 

the Gerni service organization:

Symptom Cause 

Recommended 

action

Machine refuses to  

Machine not plugged in 

Plug in machine.

start 

Defective socket 

Try another socket.

Fuse has blown 

Replace fuse. Switch off other machines.

Defective extension cable 

Try without the extension cable.

Fluctuating pressure 

Pump sucking air 

Check that hoses and connections are air- 

   tight.

Valves dirty, worn out  

Contact local Gerni service centre.

 or 

stuck 

Pump seals worn out 

Contact local Gerni service centre.

Motor busses 

Low voltage or  

Activate the trigger of the spray gun.

 low 

temperature

Machine stops 

Fuse has blown  

Replace fuse. Switch off other machines. 

Incorrect mains voltage 

Check that the mains voltage corresponds  

   to 

specifi cation on the model tag.

Thermal sensor activated 

Leave the washer for 5 minutes to cool  

   down.

Nozzle partially blocked 

Clean the nozzle (see section 7.2)

Fuse blows 

Fuse too small 

Change to an installation higher than the  

amp. consumption of the machine. 

You may try without the extension cable.

Machine pulsating

Air in inlet hose/pump 

Allow machine to run with open trigger  

until regular working pressure resumes.

Inadequate supply of  

Check that the water supply corresponds 

mains water 

to specifi cations required (see model tag) 

NB! Avoid using long, thin hoses (min.  

   1/2")

Nozzle partially blocked 

Clean the nozzle (see section 7.2)

 Water 

fi lter blocked 

Clean the fi lter (see section 7.1)

Hose kinked 

Straighten out hose.

Machine often starts 

Pump/spray gun is 

Contact your nearest Gerni Service 

and stops by itself 

leaking Centre.

Machine starts, but  

Pump/hoses or accessory 

Wait for pump/hoses or accessory to thaw.

no water comes out  frozen

No water supply  

Connect inlet water.

 Water 

fi lter blocked 

Clean the fi lter (see section 7.1)

Nozzle blocked 

Clean the nozzle (see section 7.2)

In case problems other than the above occur, please contact your local Gerni distributor.

7.3  Cleaning of machine  

vents

The machine should be kept 

clean so as to let cooling air 

7.4  Greasing of coup-

lings

To ensure an easy connec-

tion and that o-rings do 

not dry up, the couplings 

pass freely through the ma-

chine vents.

should be greased regu-

larly.

15

9 Further 

information

9.1 Recycling the 

 washer

Make the old cleaner unus-

able immediately.

1. Unplug the cleaner and 

cut the electric cable.

Do not discard electrical 

appliances with household 

waste.

As specifi ed in European 

Directive 2002/96/EC on 

old electrical and electronic 

appliances, used electrical 

goods must be collected 

separately and  recycled 

ecologically.

Contact your local authori-

ties or your nearest dealer 

for further information.

9.2 Warranty conditions

Gerni guarantees high pres-

sure washers for domestic 

use for 2 years. If your high 

pressure washer or ac ces -

so ries are handed in for 

repair, a copy of the receipt 

must be enclosed.

Guarantee repairs are made 

on the following con dit ions:

 that defects are attribut-

able to fl aws or defects 

in materials or workman-

ship. (wear and tear as 

well as misuse are not 

covered by the gu a ran -

tee).

 that the directions of this 

instruction manual have 

been thoroughly ob-

served.

 that repair has not been 

carried out or attempted 

by other than Gerni-

trained service staff.

 that only original acces-

sories have been applied.

 that the product has not 

been exposed to abuse 

such as knocks, bumps or 

frost.

 that only water without 

any impurities has been 

used.

 that the high pressure 

washer has not been 

used for rental nor used 

com mer cial ly in any other 

way.

Repairs under this guaran-

tee include replacement of 

defective parts, exclusive of 

packing and postage/car-

riage. Besides, we refer to 

your national law of sale.

The machine should be for-

warded to one of the serv-

ice centres of the Gerni or-

ganisation with description/

spe ci fi  ca ti on of the fault.

Repairs not covered by the 

guarantee conditions will 

be invoiced. (I.e. malfunc-

tions due to Causes men -

ti o ned in section Trouble 

Shooting of the instruction 

manual).

Please phone 1300 733 

171 for service or war-

ranty  assistance only 

after checking possible 

causes in the trouble 

shooting chart on page 

14.

16

9.3 Accessories

Only use original accessories.

Click & Clean

Car nozzle 

Special nozzle for enameled surfaces. Optimal dis-

tance: 30 - 50 cm.

Click & Clean

Undershassis 

nozzle 

90° angled special nozzle for undercarriage and wheel 

arches. Integrated guide shoes.

Click & Clean

Brushes

For cars and other surfaces. Available in more shapes.

Extension 

hose

7 m extension hose increasing the working range.

Drain & Tube 

cleaner

15 m long tube cleaner for the cleaning of tubes and 

drains.

Water-sand-

blasting 

equipment

For removal of paint and rust. Sand available from do-

it-yourself shops.

Patio Plus

Equipment for quick cleaning of patio/drive/fl agstones.

Wall hook

For suspension of your high pressure washer on the 

wall.

Water suc-

tion kit

For removal of large amounts of water from e.g. gar-

den pounds.

17

EU Declaration of Conformity

Product:

High Pressure Washer

Type:

Gerni Super 130.2, Super 140.2

Description:

230 V 1~, 50 Hz - IP X5

The design of the unit 

corre sponds to the follow-

ing  pertinent regulations:

EC Machine Directive 

98/37/EC

EC Low-voltage Directive 

73/23/EC

EC EMV Directive    

 2004/108/EC

Applied harmonised 

standards:

EN 60335-2-79

Applied national standards 

and technical specifi ca-

tions:  

IEC 60335-2-79

Anton Sørensen

V.P. Technical Operations 

Europe 

Nilfi sk

Division of Nilfi sk-Advance A/S

Industrivej 1

DK-9560 Hadsund

Hadsund, 01.03.2008

10 EU Declaration of Conformity

128303205  (03.2008)

Nilfi sk-Advance Pty LTd
48 Egerton St
Silverwater NSW 2128

Phone: 1300 556 710
E-mail: sales@gerni.com.au