Clearaudio Innovation Wood User Manual - User Manual

Download PDF User Manual

Full Text Searchable PDF User Manual

Innovation

Clearaudio electronic

GmbH

Spardorfer Str. 150 • D-91054 Erlangen • Tel. +49 9131 40300100 • FAX + 49 9131 40300119

www.clearaudio.de

• www.analogshop.de •

info@clearaudio.de

Version: 2.5_13.10.2016_E

User manual

Made in Germany

Innovation

Innovation Wood

Picture: Package with

Clearaudio tonearm „TT3“

and Clearaudio cartridge

„Titanium V2 “.

Picture: Package with

Clearaudio tonearm

„Universal“ and Clearaudio

cartridge „da Vinci V2 “.

Dear

Clearaudio

customer,

Congratulation’s to your choice of the

Innovation / Innovation Wood

(in the following:

Innovation

named)

turntable, a world class turntable, handmade in Germany by

Clearaudio electronic GmbH.

Resonance minimizing chassis construction in a sandwich in combination with the innovative motor unit

(low noise level and high turning moments), guarantees total isolation of resonances from the turntable

chassis, providing the best music reproduction and authentic High End imaging. A high precision,

maintenance free sinter bronze bearing is completing the analogue pleasure.

The

Clearaudio

patented CMB-Bearing-Technology, an inverted bearing with jewelled and polished

ceramic bearing shaft and a bronzed liner, provides frictionless analog enjoyment.

Please read this instruction manual carefully, to avoid any damages or loss of warranty.

This manual will help you for an easy setup and guarantees the highest pleasure for a long time.

We wish you a lot of musical enjoyments with your new

Clearaudio

Innovation

turntable.

Clearaudio electronic GmbH

This section must be read before any connection is made to the mains supply.

Innovation

User manual

WARNINGS

Don’t expose your turntable to rain or humidity.
Don’t handle the mains leads with wet hands.
Don’t place or insert anything into the equipment or through ventilation holes.
No naked flame sources, such as lighted candles, should be placed on the equipment.

CE-MARKING

EQUIPMENT MAINS WORKING SETTING

Your Clearaudio product has been prepared to comply with the household power and safety requirements

that exist in your area. This product can be connected to 230 V or 110 V AC (50 Hz and 60 Hz).

COPYRIGHT

Recording und reproduction of any sound-material may require the consent of the creator. Please acknow-

ledge the information given in the

Dramatic and Musical Performers Act 1958,

Performers Protection Acts 1963 and 1972,

Any more recent legal regulations.

Page 2

The

Clearaudio

Innovation

meets the regulations concerning electromagnetic disturbance

(EMC) and low-voltage appliances.

Contents

Packing

overview 4

List

components

Installation

and

setup

Fine

adjustment

the

motor

Service

and

special

instruction 14

Technical

data

Warranty

information

Stroboscope

Testrecord

user

manual

-18

Page 3

Innovation

User manual

1. Packing overview

Page 4

Pic. 1:

Packing overview

Accessories,

user manual,

warranty card,

Clearaudio

Quality

Card,

Stroboscope Testrecord

Innovation

turntable chassis incl.

mounted lower bearing

part and integrated

motor unit;

optional: Tonearm

Stainless steel-sub-

platter; Delrin or Acrylic

platter;

power supply;

upper bearing part and

– cap

optional: Cartridge

Innovation

User manual

2. List of components

Clearaudio

has developed a special and secure packing for your

Innovation

turntable that ensures a safe

transportation.

Please keep this original packing, if you need to ship the turntable.

Below you find the part list of the

Clearaudio

Innovation

turntable:

Page 5

Pic. 2:

List of components

Turntable body with mounted lower

bearing part

Bearing part

Stainless steel sub-platter

3 x Flat Pads

Delrin or Acrylic (Wood version)

turntable platter

Optional:

Clearaudio

Universal

(7 a) or

Magnify

(7 b) tonearm with counterweight to

adjust the tracking force

Power supply

Mounting clip for stainless steel sub-platter and

hex key

Pic. 7b: Clearaudio

Magnify

tonearm

Pic. 7a: Clearaudio

Universal

tonearm

Innovation

User manual

Continuation of components list

Page 6

16 a

1 Pair of white gloves

15.

Bearing oil for occasional use

10.

Grounding - wire for the Innovation

turntable (to connect in the bottom

bearing part)

16 a

16 b

Optional in package:

Clearaudio

MC cartridge

da Vinci

Clearaudio

MC cartridge

Talismann

Clearaudio

Smart Stylus Gauge

11.

Level gauge for the turntable

alignment

17.

Clearaudio

Stroboscope Testrecord

(Art. No. AC038) to adjust the exact speed

12.

1 pcs. flat belt

18.

Optional in package:

Turntable + tonearm + cartridge

No illustration:

Cartridge alignment gauge

for

Unify

Universal

tonearm (optional)

13.

4 pcs. hex wrench; sizes: #1,5; #

2,5; #3; #7

19.

Not shown: warranty card,

Clearaudio

Quality

Card, Sales return paper

14.

Screw driver

17.

Not shown: User Manual

Pic. 2.1:

List of components

IMPORTANT NOTICE:

Please double check the tightness of all bolts, hardware, and mounting pods, as temperature fluctuations

during transit may have caused the hardware to become loose.

16 b

Innovation

User manual

Page 7

3. Installation and setup

The setup of the

Innovation

turntable is easy as the turntable chassis is pre-assembled and has been

tested at the factory.

Please use the white gloves enclosed in order to avoid scratches or unwanted fingerprints (platter).

The

Innovation

turntable requires a space for setup of at least 18.90 inch x 19.29 inch.

18.90 inch

/ 480 mm

19.29 inch / 490 mm

Pic. 3:

Required set - up space

Innovation

User manual

Page 8

Please follow the description step by step:

1.)

First take out the three black flat pads out of the accessory bag.

Place these flat pads on your hifi-rack or another suitable base, where the final position of your

Innovation

turntable will be.

2.)

After that, take the Innovation turntable body of the next packing layer and place the spikes of the

turntable on the flat pads.

Pic. 4:

Innovation

with tonearm base

Pic. 6:

Oiling the bearing shaft

3.)

To avoid hum noises it can be necessary to ground the bearing. For that please plug in the provided ground

cable into the hole of the screw from the bearing at the bottom side of the turntable.

Pic. 5:

Grounding the bearing of the

Innovation

4.)

Remove the protective security tape from the bearing housing.

Place two drops of the synthetic bearing oil on the ceramic bearing shaft.

(also available at

www.analogshop.de,

Art. No. AC068)

Innovation

User manual

Page 9

5.)

Take the stainless steel platter with both hands carefully out of the box.

Remove the lamination of the scale ring on the lower side of the turntable.

Please remove the lamination extreme carefully and avoid any soiling and scratches.

Push the delivered bearing part carefully through the hole in the stainless steel sub-platter and mount the

bearing part with the sub-platter by using the mounting clip.

6.)

In the next step remove the lamination of the sensor, mounted on the turntable chassis (picture 6: red

frame).

Please remove the lamination extreme carefully and avoid any soiling and scratches.

Pic. 7:

Connection sub-platter and bearing upper part

Pic. 8:

Removing the lamination

7.)

With both hands you can place the stainless steel platter

carefully onto the bearing.

Through a lightly (!!) up and down movement the platter will

slip onto the bearing upper part (picture 8).

Make sure with gentle pressure that the platter is applying on

the complete surface of the bearing.

Avoid major side forces to avoid any damages to the

ceramic bearing!

Pic. 9:

Setup stainless steel platter with

upper bearing part

Innovation

User manual

Page 10

8.)

Now you can remove the mounting clip with the delivered hex wrench.

9.)

Take the Delrin platter with both hands out of the box and set

the platter carefully onto the bearing.

The flat side of the platter should face to the stainless steel

platter and the side with the cut-out (for the record) should

face

up.

To avoid any damages on your bearing, the Delrin platter

should have room temperature before the setup begins

(approx. 20 ° Celsius).

Avoid major side forces to avoid any damages to the

ceramic

bearing

Pic. 10:

Removing of the mounting clip

Pic. 11:

Setup Delrin platter and bearing

cap

You will find suitable adjustment equipment under

www.clearaudio.de

www.analogshop.de

10.)

To install the tonearm, please follow the user manual of the manufacturer.

Innovation

User manual

Page 11

11.)

To mount and adjust a cartridge, please follow the user manual of the manufacturer.

If you purchased your

Clearaudio

Innovation

turntable as a package with tonearm and cartridge, you will

find a

Smart Level Gauge

in your accessory, which will help you to adjust the Tracking Force of the

cartridge:

Pic. 12:

Use of Smart Stylus Gauge

Innovation

User manual

✓



tracking force too high! /

Auflagekraft zu hoch!



tracking force too low! /

Auflagekraft zu niedrig!

Diese Position der Nadel entspricht

einer Auflagekraft von 20 mN (2,0g).

This position of the diamond correlates

to a tracking force of 20 mN (2.0g).

Page 12

12.)

The following final adjustment is very important:

Please ensure that your turntable rack is in a levelled position.

Please check with the bubble level gauge, if your

Innovation

turntable is in a levelled position.

You can adjust each of the turntables feet to get the turntable levelled.

Only if the turntable is in a levelled position you will get the best results with your

Innovation

turntable.

Pic. 13 a:

Alignment of the

turntable

Pic. 13 b:

Adjustment of the turntables`feets

13.)

Please connect the mains plug to your power supply.

14.)

Place the flat belt around the platter and around the

motor pulley.

By pushing the sensor-switch, marked with “33 1/3” on

the motor, the turntable starts to spin until 33 1/3 rpm is

reached.

After the initial setup we recommend to let the turntable

spin for at least 15 to 30 minutes.

This ensures a smoother break in.

Pic. 14:

Connection power supply and motor

Innovation

User manual

4. Fine adjustment of the

Innovation

motor

1.)

The motor adjustment is already pre set at the factory. Through the transport or through soiling on the

sensor or the sensor ring some small speed deviations can occur.

Please check the speed before using the turntable for the first time.

For the correct adjustment of the speed please put the recommended

Clearaudio

Stroboscope

Testrecord

on the platter. Follow hereby the instruction of the

Stroboscope Testrecord

user manual.

To check the speed with highest accuracy please use the

Clearaudio

Speed Light

(Art. No. AC039,

www.analogshop.de

On the front side of your turntable there are three setting trimmers (see Pic. 15).

- Left trimmer = setting 33 1/3 rpm

(near turntable motor)

- Middle trimmer = setting 45 rpm

- Right trimmer = setting 78 rpm

(near turntable bearing)

Pic. 15:

Fine adjustment of the motor (on the

backside)

If you like to adjust the speed 33 1/3 rpm, take the Aluminum screw driver (see accessories) and turn the

left trimmer until you have reached the right speed according to the Stroboscope Testrecord (see user

manual “Stroboscope Testrecord”).

Turning the trimmer counter clockwise = reduces the turntable speed

Turning the trimmer clockwise = raises the turntable speed

Please proceed with the speed adjustment for 45 rpm and 78 rpm in the same way!

Please note:

If the turntable does not reach the correct speed, the sensor or the scale ring could be dirty or dusty.

To clean the sensor, please take off the platter very carefully!

Clean the sensor and the scale ring with a little isopropyl alcohol and a cotton bud.

Be careful and avoid any scratches on the sensor or the scale ring!

If the motor has further more speed variations please contact your nearest authorized

Clearaudio dealer

or directly the

Clearaudio

factory (address on page 14).

If the turntable is not in use, disconnect the unit completely from the power supply by removing the main

plug from the socket.

Now you are finally ready to play your vinyl records.

We wish you a lot of pleasure with your new

Innovation

turntable.

Page 13

Innovation

User manual

5. Special instruction

5.1 Maintenance

• If the

Innovation

turntable is a longer time not in use, please disconnect the motor from the main

supply.

• Every two years you can lubricate the bearing of the turntable platter with the delivered oil.

In this case it is enough to put 1 or 2 drops of the oil into bearing.

• Please take special caution to any damages of the power cord. Any damages should be repaired only by

authorized personal.

A damaged power cord must be exchanged immediately!

Caution:

Please use only non alcoholic fluids and only fluids specially used for acrylic, to clean the

Innovation turntable.

Otherwise damage on the material or the surface can occur!

Don’t use try cloths for cleaning because of the electrostatic charging. Suitable cleaning fluids

will be available at Clearaudio

(www.analogshop.de)

or your Hifi dealer.

5.2 Transport

Send / ship the

Innovation

turntable always and only in the original packing!!!

Only in the original packing

Clearaudio

can provide the warranty. If you repackage the turntable, please

make all steps inverted like at installation and setup (chapter 3).

• If any transportation of the

Innovation

turntable should be necessary, please always remove the

turntable platter and the shaft holder. Otherwise serious damage can occur!

• To avoid any dust coming into the bearing, the bearing hole needs to be covered as well.

Only if the product is returned in its original packing

Clearaudio

can provide the warranty.

5.3 Service

In case of any necessary, service for all

Clearaudio

products should be done by authorized personal only.

In case of any repair, the

Clearaudio

Innovation

turntable needs to be send to your nearest authorized

Clearaudio

distributor, dealer or directly to the

Clearaudio

factory.

Clearaudio electronic GmbH

Spardorfer Str. 150

91054 Erlangen

Germany

Phone: +49 9131 40300 100

Fax: +49 9131 40300 119

www.clearaudio.de

www.analogshop.de

info@clearaudio.de

Page 14

Innovation

User manual

Clearaudio

electronic is not responsible for typographical errors in descriptions. Technical specifications subject to

change or improvement without prior notice. Availability as long as stock lasts. Copies and imprints- also only in

extracts – require written conformation through

Clearaudio

electronic GmbH; Germany

6. Technical data

Construction principle:

Resonance optimised chassis’s shape, belt driven with optical,

full automatic speed control

Speed possibilities:

33 1/3 rpm / 45 rpm / 78 rpm

Drive unit:

Decoupled DC motor in a massive metal-housing.

Bearing:

Inverted and polished ceramic bearing shaft, polished sinter

bronze insert, including patented CMB bearing technology

Platter:

VA stainless steel sub-platter, Delrin or acrylic GS-PMMA platter,

precision CNC machined surface

Speed variation less than:

+/- 0.05 %

Deviance of the set value:

+/- 0.01 %

Weight:

approx. 25 kg (without tonearm and power supply)

Dimensions (w x d x h):

approx. 428 mm x 390 mm x 208 mm

(16.85 inch x 15.35 inch x 8.19 inch)

Power consumption:

Max. consumption:

Consumption in operation:

Stand by mode:

Off mode:

9.3 Watt

2.5 Watt

0.0 Watt

Warranty:

5 years* (see page 16)

* Only if the warranty card is filled out correctly and sent back to

Clearaudio

within 14 days.

Version: October 2016

Page 15

Innovation

User manual

To achieve the full

Clearaudio

warranty (Innovation turntable 5 years), it is necessary that you fill out and send the

corresponding part of the warranty registration certificate /card back to

Clearaudio

, within two weeks after purchase.

Only if the product is returned in its original packing

Clearaudio

can provide the warranty of 5 years.

ENGLISH

WARRANTY

For warranty information, contact your local clearaudio distributor.

RETAIN YOUR PURCHASE RECEIPT

Your purchase receipt is your permanent record of a valuable purchase.

It should be kept in a safe place to be referred to as necessary for insurance purposes or when corresponding with clearaudio.

IMPORTANT

When seeking warranty service, it is the responsibility of the consumer to establish proof and date of purchase. Your purchase receipt or invoice is

adequate for such proof.

FOR U.K. ONLY

This undertaking is in addition to a consumer‘s statutory rights and does not affect those rights in any way.

FRANÇAIS

GARANTIE

Pour des informations sur la garantie, contacter le distributeur local clearaudio.

CONSERVER L‘ATTESTATION D‘ACHAT

L‘attestation d‘achat est la preuve permanente d‘un achat de valeur. La conserver en lieu sur pour s‘y reporter aux fins d‘obtention d‘une couverture

d‘assurance ou dans le cadre de correspondances avec clearaudio.

IMPORTANT

Pour l‘obtention d‘un service couvert par la garantie, il incombe au client d‘établir la preuve de l‘achat et d‘en corroborer la date. Le reçu ou la

facture constituent des preuves suffisantes.

DEUTSCH

GARANTIE

Bei Garantiefragen wenden Sie sich bitte zunächst an Ihren clearaudio-Händler.

Heben Sie Ihren Kaufbeleg gut auf.

WICHTIG!

Die Angaben auf Ihrer Quittung erlauben uns die Identifizierung Ihres Gerätes und belegen mit dem Kaufdatum die Dauer Ihrer Garantie-Ansprü-

che. Für Serviceleistungen benötigen wir stets die Gerätenummer.

Diese finden Sie auf dem Typenschild auf der RückPage des Gerätes oder auf dem Tonarm sowie in der beigefügten Garantie-Registrierkarte.

NEDERLANDS

GARANTIE

Voor inlichtingen omtrent garantie dient u zich tot uw plaatselijke clearaudio.

UW KWITANTIE, KASSABON E.D. BEWAREN

Uw kwitantie, kassabon e.d. vormen uw bewijs van aankoop van een waardevol artikel en dienen op een veilige plaats bewaard te worden voor evt,

verwijzing bijv, in verbend met verzekering of bij correspondentie met clearaudio.

BELANGRIJK

Bij een evt, beroep op de garantie is het de verantwoordelijkheid van de consument een gedateerd bewijs van aankoop te tonen. Uw

kassabon of factuurzijn voldoende bewijs.

ITALIANO

GARANZIA

L’apparecchio è coperto da una garanzia di buon funzionamento della durata di un anno, o del periodo previsto dalla legge, a partire dalla data di

acquisto comprovata da un documento attestante il nominativo del Rivenditore e la data di vendita. La garanzia sarà prestata con la sostituzione o

la riparazione gratuita delle parti difettose.

Non sono coperti da garanzia difetti derivanti da uso improprio, errata installazione, manutenzione effettuata da personale non autorizzato o, co-

munque, da circostanze che non possano riferirsi a difetti di funzionamento dell’apparecchio. Sono inoltre esclusi dalla garanzia gli interventi inerenti

l’installazione e l’allacciamento agli impianti di alimentazione.

Gli apparecchi verranno riparati presso i nostri Centri di Assistenza Autorizzati. Le spese ed i rischi di trasporto sono a carico del cliente. La casa

costruttrice declina ogni responsabilità per danni diretti o indiretti provocati dalla inosservanza delle prescrizioni di installazione, uso e manutenzione

dettagliate nel presente manuale o per guasti dovuti ad uso continuato a fini professionali.

ESPAÑOL

GARANTIA

Para obtener información acerca de la garantia póngase en contacto con su distribuidor clearaudio.

GUARDE SU RECIBO DE COMPRA

Su recibo de compra es su prueba permanente de haber adquirido un aparato de valor, Este recibo deberá guardarlo en un lugar seguro y utilizarlo

como referencia cuando tenga que hacer uso del seguro o se ponga en contacto con clearaudio.

IMPORTANTE

Cuando solicite el servicio otorgado por la garantia el usuario tiene la responsabilidad de demonstrar cuándo efectuó la compra. En este caso, su

recibo de compra será la prueba apropiada.

Innovation

User manual

Page 16

Stroboscope Testrecord

User manual

Innovation

User manual

The

Clearaudio

Stroboscope Testrecord

satisfies the highest demands for an exact speed adjustment for

turntables. Dramatic sound improvements can be reached only with exact calibrated speeds.

- Optimal adjustment for turntables -

To adjust the exact speed, please choose the side for 50 / 60 Hz, or the other side for the use with the

speed light first. If you choose the side without the speed light source, you can use the regular light

source for the installation, either 50 Hz (outer scales) or 60 Hz. The scales

are graduated in three different reading options:

33.3 Hz, 45 Hz and 78 Hz (starting from the outer diameter).

Please place the

Stroboscope Testrecord

on your turntable platter and start

the engine of your turntable. The big advantage of the

Clearaudio

Stroboscope Testrecord

is, that you can place your cartridge onto the

Stroboscope Testrecord

, while

measuring the speed, as there are grooves provided on the disc. This means, for the first time a real time

speed analysis is possible under realistic circumstances.

If you have the impression that the horizontal lines move on the scale, you should set or readjust the

speed of the motor again.

- If the lines move clockwise, the speed is too fast.

- If the lines move counter clockwise, the motor speed is too slow.

Please correct the speed on your motor or turntable until you have the impression that the lines stopped

moving. After that you have reached the exact speed and you can enjoy the full potential of your vinyl

collection again.

Page 17

Page 18

Innovation

User manual

If you use the

Speed Light

(Art. No. AC039) you can reach an even higher or more

accurate adjustment, completely independent of the power line or frequency of your

country. As well, the 300 Hz calibrated light, used as an external light source is

completely independent from possible power line fluctuations, which could influence

the result by regular light. The 300 Hz of the

Speed Light

are generated by a

stabilized quartz oscillator and permit a very exact adjustment. Please put the

Stroboscope Testrecord

with the fine lines upward on your turntable. Here you also

have the possibility to choose between two different speeds.

With the outside scale you can detect the speed of 33 Hz and with the inside scale you can detect the

speed of 45 Hz. Again, the big advantage of the

Clearaudio

Stroboscope Testrecord

is, that you can place

your cartridge onto the

Stroboscope Testrecord

, while measuring the speed, as there are grooves provided

on the disc. This means, for the first time a real time speed analysis is possible under realistic

circumstances.

Press the button of the speed light source and place it parallel over to the scale and adjust the motor or

turntable speed until the horizontal lines do not move anymore.

- Tip -

As more accurate your turntable speed is adjusted, as better the overall sonic appearance of the record

playback will be!

It is mandatory to check the speed several times through out the year, to ensure that other influences are

not minimizing the sound quality.

Technical Data:

Speed Light

Light source:

blue LED / 300 Hz precision light source (calibrated)

Battery:

V23GA – 12 V – Alkaline (Art. No.: AC039/B)

(Technical changes are subject without notification)

Date: 10/2016

Clearaudio electronic GmbH

Spardorfer Str. 150

91054 Erlangen

Germany

Phone: +49 9131 40300 100

Fax: +49 9131 40300 119

www.clearaudio.de

www.analogshop.de

info@clearaudio.de

Ask a Question ?