Full Text Searchable PDF User Manual
Instruction and installation manual
1. Safety Precautions
2. Names of Parts
3. The Features of MP02
4. Cartridge Replacement Period
5. Cartridge Replacement Method
6. Troubleshooting
7. After-sales Service
8. Installation Precautions
8-1.Pluming
8-2.Installation Example of the Water Purifier
(Softener)
8-3.Connection
8-4.Water Flowing Test and Leakage Check
8-5.Adjustment of Filtered Water Volume
●
Warranty
Thank you very much for purchasing Cleansui MP02 series. Read these instructions
carefully before use. An installation instruction and warranty are included with this
product, and they must be retained for future reference.
●
Please read all pages use this product in proper way.
●
After reading, retain this book at the place where is ready to access, please.
Contents
●
Commercial water purifier (MP02-1E MP02-2E MP02-3E MP02-4E)
●
Water softener with water purification function (MP02-5E MP02-6E)
MP02 series
2
Failure to follow the safety precautions can lead to a serious accident. They contain extremely
important information related to safety and all instructions must be observed without fail.
Warning
Attention
Prohibition
Instruction
The articles with this mark
indicates possible serious
injury or fatal accident.
Indicates “prohibited” actions.
Indicates “mandatory
instructions”.
Indicates failure to observe
these instructions can cause
minor injury to the user or
damage to surrounding
property.
The degrees of potential danger and damage that can be caused from any improper
use or ignoring the contents of the safety precautions are explained below.
1. Safety Precautions
Attention
Do not use this device to filter hot water above 35
℃
.
Do not use filtered water in fish tanks, etc.
When the filtration performance declines through usage, residual
chlorine may remain in filtered water. This may be fatal to fish.
Do not apply strong force or shock to the water purifier
(softener) and connection.
Keep the heated appliances (frying pan etc.) away from
the water purifier (softener), pipes and hoses.
It causes damage or leakage, and that may result in property damage.
If you have not used the purifier (softener) for more than
half a month, please replacethe cartridge.
Do not touch the “pure water” outlet with your hand or
cloth.
If the wateroutlet becomes soiled by splash back etc. Run
filtered (softened) water for 15 seconds.
For the maintenance of the wateroutlet, clean with a
sterilized soft toothbrush etc.
If you do not keep the wateroutlet clean all the times, bacteria may
multiply.
Do not use detergent and organic solvents (thinners
gasoline etc.) for cleaning.
Please use wet towel etc. for cleaning.
If seasonings that contain salt, sticks to the stainless steel
parts, wipe with a clean damp cloth to remove salt.
Please confirm there is no leakage around connections
and water purifier (softener) once a month.
It is not recommended that customers attempt disassembly
or repairs themselves. Contact your supplier.
It is recommended that the area around the unit be
waterproof to avoid damage should leakage occur.
The ambient temperature must be less than 60
℃
.
The heat may warp and break the water purifier (softener), and that may
cause leakage.
If the working water pressure is more than 0.35MPa,
please adjust it to 0.2MPa with a reducing valve.
(Reducing valve is not included.)
Warning
Attention
Please use tap water that meets the local standards for
drinking water.
It cannot be used to purify hot-spring water, well water or any other
water that contains large amounts of impurities. Uses of the water filter
in this way may be detrimental to your health.
Please consume filtered (softened) water as soon as
possible.
Hollow fibre membrane units MP01-1E and MP02-4E are
recommended for use in ice machines and cold drink
vending machines.
Replace the cartridge regularly.
Recommended purifier cartridge replacement period is 12 months and in
the case of the softener cartridge, it is 6 months. Continuous usage of
the cartridge which is exhibiting reduced water volume output, due to
clogging, may cause damage and leakages, which may result in property
damage. Water purifying performance may not be adequate with the
cartridge that has passed the recommended replacement period.
When you start using a new cartridge, please let the water
flow until there are no more bubbles in the water (About 3
minutes for MP02-1E, 4E, about 5 minutes forMP02-2E, 3E).
Also confirm that there is no leakage at the same time.
To remove the retained water, please let the water flow for
about 2 minutes in the cases of MP02-2E and 3E, about 30
seconds in the cases of MP02-1E, 4E, 5E, 6E before using
everyday.
When the red water flows from tap after cutting the water
supply, you should not put this water through the water
purifier (softener).
If you let the red water flow through the water purifier (softener), the
performance will be considerably impacted.
This system must be used with the dedicated cartridge.
This system must not be installed at any location where it
might become frozen.
This system is not assumed to be used in cold districts.
Don't touch the water purifier (softener) when leakage is
evident.
It causes a short circuit and you may get an electric shock.
3
MP02 series included parts list
Please confirm all parts indicated below are included first.
●
Stainless steel container 1set
(Including a lid for outer tube, outer tube body,
clamp and rubber seal)
●
Cartridge 1
●
Frame plate
(with screws and fixing nuts)
1
●
Plate
(with fixing nuts)
1
●
Mounting frame
(with a screws)
1
Lid for outer tube
Clamp
Rubber seal
Cartridge
Outer tube body
Mounting frame
Fixing nut
Plate
Frame plate
Tap water supply valve
Dedicated stop valve for
water purifier (softener)
Clamp
“OUT” side
“IN” side
Stain steel container
(with a cartridge)
This instruction manual has illustrations in case of using dedicated faucet for filtered (softened) water.
2. Names of Parts
Handle
Dedicated faucet for filtered (softened) water or
other water supplying appliance.
Pressure-resistant blade hose or flexible pipe
From “OUT” side of water purifier (softener) to
dedicated faucet for filtered (softened) water
Pressure-resistant blade hose or flexible pipe
From the dedicated faucet (filtered/softened water)
to “IN” side of water purifier (softener)
“T” joint with a nut
4
3. The Features of MP02
●
MP02-1E
(Hollow fibre membrane)
The less than 0.1 micrometre
pores on the sidewall of hollow
fibre membrane can remove
bacteria, red rust and lead
particle etc.
●
MP02E-2/3E
(granular and fibrous activated
carbon + non-woven fabric)
Granular and fibrous activated
carbon filtrate tap water. This
system can supply large
amount of filtered water with
minerals. This system can be
connected with existing faucet,
coffee machine and rice
washer etc.
●
MP02-4E
(Activated carbon + Hollow fibre
membrane + Non-woven fabric)
This system has the triple filtration
system consists of fibrous activated
carbon, hollow fibre membrane
(polyethylene) and non-woven
fabric. It removes unpleasant
odours, chlorine, mold (2-MIB),
bacteria and metal particles such
as rust, lead and etc.
MP02-1E
60,000L
※
Please use models with hollow fibre membrane to remove bacteria. (MP02-1E, MP02-4E)
※
MP02-2E, MP02-3E, MP02-5E, MP02-6E can not remove bacteria.
※
Please use MP02-5E, MP02-6E to remove water hardness.
MP02-2E
100,000L
MP02-3E
150,000L
MP02-4E
50,000L
For turbidity removing
(Can be used with MP02-2E, 3E, 5E, 6E)
For anti-scale (For tea dispenser,
coffee machine, rice washer etc.)
For ice machine, cold drink
For removing water hardness (Water
softener with purification function)
●
MP02-5E/6E
(Caution-exchange resin + Activated
carbon + Nonwoven fabric)
It removes the hardness components
in tap water (calcium, magnesium).
It also removes free residual chlorine
and unpleasant odours etc.
MP02-5E
5,000L
MP02-6E
3,000L
●
Specifications
Model No.
Cartridge Model Number
Material
Cartridge components
Initial water flow rate
MP02-1E
MP02-2E
MP02-3E
MP02-4E
MP02-5E
MP02-6E
UMM0050E
UMC2100E
UMC2150E
UMC2050E
USC-5E
USC-6E
Hollow fibre
membrane
(Polyethylene)
Granular and fibrous activated carbon,
Non-woven fabric
10
L
/minutes
10
L
/minutes
10
L
/minutes
8
L
/minutes
5
L
/minutes
5
L
/minutes
0.07MPa
0.07
〜
0.35MPa
――
100,000
L
150,000
L
50,000
L
5,000
L
3,000
L
60,000
L
――
――
50,000
L
――
――
――
――
――
――
5,000
L
3,000
L
1.5kg
（
3.3kg
）
1.5kg
（
3.3kg
）
1.6kg
（
3.3kg
）
1.7kg
（
3.0kg
）
4.3kg
（
5.4kg
）
3.5kg
（
5.0kg
）
Maximum diameter 160mm
×
Height 300mm
Hollow fibre membrane
(Polyethylene),
Fibrous activated carbon,
Non-woven fabric
Stainless steel
container
Cartridge
Stainless
ABS resins
Based on
JIS S 3201.
80% removed
Caution-exchange resin,
Activated carbon,
Non-woven fabric
Caution-exchange resin,
Activated carbon,
Non-woven fabric
Minimum working
water pressure
The appropriate working
water pressure range
Filtration
performance
Free residual
chlorine
Turbidity
Minimum working water pressure
(Original hardness 50mg/L)
Weight of the main body
(When filled with water)
Cartridge size
Dimensions of stainless
steel container
Maximum diameter
91mm
×
153mm
Maximum diameter
92mm
×
330mm
Maximum diameter
85mm
×
247mm
Maximum diameter
85mm
×
247mm
Maximum diameter
91mm
×
252mm
Maximum diameter
92mm
×
450mm
Maximum diameter160mm
×
Height 495mm
Maximum diameter160mm
×
Height 380mm
Attention
5
Model
No.
4. Cartridge Replacement Period
Approximate replacement period of the cartridge
MP02-1E
12 months (In case of 160 litres/day use)
MP02-2E
12 months (In case of 270 litres/day use)
MP02-3E
12 months (In case of 410 litres/day use)
MP02-4E
12 months (In case of 135 litres/day use)
MP02-5E
6 months (In case of 27 litres/day use)
MP02-6E
6 months (In case of 16 litres/day use)
Please change the cartridge as soon as
one of the following situations arise:
※
The replacement period differs in
accordance with the amount of water
volume, water quality, pressure and
hardness etc.
●
Water volume decreased steeply (clogging).
●
You experience an unpleasant taste or odour (filtration performance becomes lower).
It is recommended that a plumber facilitate the cartridge replacement.
●
The accumulated stain inside the cartridge will decrease the purifying performance substantially and
result in it being unsanitary.
●
Clogging of the cartridge and degradation of the cartridge body causes leakage.
・
Please contact the store where you bought Cleansui, or installation contractor, and
request maintenance.
※
Refer to P.8
・
The cartridge is a consumable, and therefore a replacement cost will be incurred.
This is for your expense.
The cartridge of a water purifier (softener) is a consumable. Replace it periodically
as recommended in the table below. If you don't replace it...
6
5. Cartridge Replacement Method
Please follow this cartridge replacement method. Failure to follow this method may cause
leakage and destruction.
Attach the dedicated
cartridge only.
When the cartridge is replaced,
place a cloth on the floor as there
will be leakage from the water
inside the cartridge.
1
Close the dedicated faucet for
water purifier (softener) and
dedicated stop valve for water
purifier (softener).
7
Allow the filtered water to flow, and check there is no
leakage.
Dedicated faucet for water purifier (softener): Fully-opened
Fully-open the dedicated faucet for water purifier (softener) gradually. And
drain water in order to remove the inside air and wash the filtration
components (MP02-1E, 4E: 3 minutes MP02-2E, 3E: 5 minutes MP02-5E,
6E: 1 minute). And keeping this situation, check there is no leakage.
2
Unfasten the handle.
Dedicated stop valve
for water purifier
(softener)
Dedicated
faucet for
water
purifier
(softener)
Handle
Rubber seal
Handle
Dedicated stop valve for
water purifier (softener)
Dedicated
faucet for
water purifier
(softener):
Fully-opened
6
Set the outer tube body.
①
Set the rubber seal to the outer tube
body, and insert it into the lid for outer
tube.
②
Set the clamp, and fasten the handle
firmly.
7
9
Adjust the “filtered water flow amount”.
Please keep the dedicated faucet for water purifier (softener) opened,
and adjust the "filtered water flow amount" with the dedicated stop valve
for water purifier (softener).
3
Extend the clamp and take
it off.
4
Remove the outer tube body.
Pull out the outer tube body from the lid
for outer tube body. And remove the
rubber seal.
5
Replace old cartridge with new one
①
Turn the old cartridge counter-clockwise (left)
and remove it.
②
Turn the new cartridge clockwise (right) more
than 2 revolutions,and
screw in completely
.
Appropriate water flow rate
MP02-1E
About 200 ml/sec
MP02-2E
About 200 ml/sec
MP02-3E
About 200 ml/sec
MP02-4E
About 200 ml/2 sec
MP02-5E
About 200 ml/2 sec
MP02-6E
About 200 ml/2 sec
Old cartridge
New cartridge
Clamp
Outer tube body
Lid for outer tube
If the fastening is not enough,
the cartridge may come off and it
can not work properly.
8
Check there is no leakage around the
clamp.
If there is a leakage, check the setting of the rubber seal
and fasten the handle firmly.
8
6. Troubleshooting
Please check the items indicated in below chart.
Please contact the store where you bought Cleansui, or installation
contractor, and request maintenance.
Problem
Potential causes
Solution
●
The filtered (softened) water does not
come out of the faucet.
Dedicated stop valve for water
purifier (softener) is closed.
“OUT” and “IN” connections are
reverse.
Dedicated stop valve for water purifier
(softener) is not fully-opened.
Cartridge is clogged.
Dedicated stop valve for water
purifier (softener) is closed.
Please fully-open the dedicated stop valve for
water purifier (softener).
※
Refer to p.7
Re-connect properly.
※
Refer to p.11
Please fully-open the dedicated stop valve for
water purifier (softener).
※
Refer to p.7
Please replace the cartridge.
Please fully-open the dedicated stop valve for
water purifier (softener).
※
Refer to p.7
●
Despite new cartridge, water volume is
slow.
●
The water flow rate is coming down
gradually.
●
The filtered (softened) water does not
come out.
If there is a leak,
close the dedicated stop valve
for water purifier (softener) first.
Problem
Potential causes
●
There is a leakage from connection.
●
There is a leakage from water purifier
(softener).
Connection is incorrectly done.
The main body of the water purifier
(softener) may be damaged.
■
Before asking for a service (maintenance or repair)
1.Refer to section “6. Troubleshooting” and verify the details of the
situation.
2. Having verified the situation, please contact the store or
contractor.
3. When you make an inquiry, please inform them of the following
points.
①
Product
……
Commercial water purifier/Water softener with
water purification function
Cleansui MP02
②
Model No.
…
MP02-1E
〜
6E
③
Problems
…
Let us know in detail.
■
Warranty
Cleansui comes with a warranty. Full details including dealer's
name, the date of purchase etc. must be completed accurately and
duly returned. The validity of the warranty is 2 year from the date of
purchase, subject to term & conditions listed on the warranty.
■
Replacement of cartridge (sold separately)
1. Please contact the store or contractor when you need to replace
the cartridge or other parts.
2. If you need to buy the cartridge, please quote specific model
number:
Model No. (for MP02-1E) UMM0050E
Model No. (for MP02-2E) UMC2100E
Model No. (for MP02-3E) UMC2150E
Model No. (for MP02-4E) UMC2050E
Model No. (for MP02-5E) USC-5E
Model No. (for MP02-6E) USC-6E
7. After-sale Service
Attention
9
8. Installation Precautions
■
Installation data
●
Diametre of pipe connecting point: G 1/2
●
Appropriate water pressure range:
0.07
〜
0.35 MPa
●
Pressure durability:
1.75 MPa (17.8 kg/cm
2
)
×
1 minute
●
Free residual chlorine: More than 0.1 mg/L of
tap water
Check
points after
installation
Transfer
Installation date / /
①
Water pressure is less than 0.35 MPa.
………………………
□
②
Installed only with included parts.
……………………………
□
③
No leakage.
……………………………………………………
□
④
Adjustment of filtered water volume.
…………………………
□
①
After installation, if you don't use the system for a long time,
close the stop valve with referring to instruction book.
②
Please explain followings to your customer with instruction book.
・
Please explain how to use the purifier (softener) and safety precautions
certainly.
・
Please recommend the regular maintenance by technical expert to your
customer.
・
The warranty is attached with this product. Please hand this instruction book
and warranty to the customer certainly.
The parts which are prepared by installation contractor.
●
Pressure-resistant blade hose or flexible pipe
…
2
●
Dedicated faucet for water purifier (softener)
…
1
●
Stop valve
………………………………
1
●
“T” joint with a nut
……………………………
1
●
At plumbing, connection, and installment of dedicated faucet for water purifier (softener) etc., please prepare the dedicated
stop valve for water purifier (softener), water distribution stopcock and pipes etc. by installation contractor.
※
The pressure-resistant blade hose should be meet the appropriate quality.
Please read this instruction manual carefully. Should you fail to do so and as a result cause
damage to the unit, we will not take responsibility.
Installation is to be done by a plumber only.
Customers are not to attempt installation
themselves.
Read P2 “1. Safety precautions”.
Confirm all parts are included certainly before installation.
Water pressure inspection
Measure the water pressure before installation.
If the working water pressure is more than 0.35MPa
(3.5kgf/cm
2
), please adjust it to 0.2MPa (0.2kgf/cm
2
) with
reducing valve (Reducing valve is not included). The
appropriate static water pressure range is from 0.07 to
0.75MPa (from 0.7 to 7.5kgf/cm
2
), and the appropriate
working water pressure range is from 0.07 to 0.35MPa
(from 0.7 to 3.5kgf/cm
2
).
10
8-2. Installation Example of the Water Purifier (Softener)
Considering the connecting ranges and maintainability ,select appropriate installment style from 3 choices (A
〜
C).
A Vertical installation
C Horizontal installation
B Wall-mounted
Install the tube outer body upright
on the flat place with the
mounting frame.
Prop up the lid for outer tube with
the frame plate, and the outer tube
with the mounting frame.
Install horizontal with the frame
plate and mounting frame. It is
appropriate for small space.
●
Like as the above illustration,
fasten the “OUT”side nipple,
plate, and frame plate with
the fixing nuts, and set the
outer tube body to the
mounting frame.
●
Install the mounting
frame with screws and
fixing nuts firmly, and
set the outer tube body
to the mounting frame.
More than
100 mm
More than
100 mm
A
B
C
For strength protection of outer tube body, the fixing nuts, plate and frame plate should be set while you use this
system.
Please handle the cartridge carefully.
MP02-5E and MP02-6E cannot be used in
horizontal position.
●
Set the water purifier
(softener) to the
mounting frame. The
purifier (softener) should
be touching the floor as
the appropriate position.
Keep the space more than 100 mm from
the floor for cartridge replacement.
Keep the space more than 100 mm from
the side wall or back wall for cartridge
replacement.
8-1. Plumbing
●
Connect “T” joint with a nut and water main, and
dedicated stop valve for water purifier (softener).
※
Dedicated stop valve for water purifier (softener) is a
necessity for after-maintenance (adjustment of filtered water
flow amount, and cartridge exchange etc.).
※
Dedicated faucet for water filtered (softener) should be used
only for purified (softened) water in plumbing.
Attention
For maintenance, the length of pressure-resistant blade hose or
flexible pipe is should not be too long (less than 1 metre). If the
length of pressure-resistant blade hose is too long, loop it at a
moderate pace. Then, pay attention not to break the pressureresistant
blade hose especially.
Dedicated stop valve for
water purifier (softener)
Water main
“T” joint
with a nut
Pressure-resistant blade
hose or flexible pipe
11
①
Connect the dedicated faucet for purifier (softener) or other
faucet and the “OUT” side nipple with the pressure-resistant
blade hose.
②
Connect the dedicated stop valve
for purifier (softener) and the “IN”
side nipple with the pressure-
resistant blade hose.
For strength protection, the fixing
nuts, plate and frame plate
should be set before installation.
●
The lengths of piping between the purifier (softener) and
faucets should be less than 1m. And install the pipes in
the range not to be polluted.
●
Use one faucet per one water purifier (softener) as a principle.
●
When this system is connected with the faucet except dedicated
one, we recommend the combination with something like
automatic drainage function.
Connect the “OUT” side and “IN” side properly.
8-3. Connection
8-4. Water Flowing Test and Leakage Check
8-5. Adjustment of Filtered Water Volume
If there is a leakage from the water purifier (softener), close the stop valve, and contact
with the store where you bought Cleansui, or installation contractor.
If you attach dome nut, tighten the screw with 2 wrenches firmly.
Before that, set a rubber seal certainly.
To use water purifier (softener) properly,
the adjustment of water volume and
enough drainage time are important.
Please observe the indications.
General view of the connection
①
Fully-open the dedicated faucet for water
purifier (softener) , and then open the
dedicated stop valve for water purifier
(softener) gradually.
②
keep this situation, and drain filtered water
until the bubbles disappear from
water.(MP02-1E, 4E: About 3 minutes
Mp02-5E, 6E: About 1 minute)
③
After drainage, close the dedicated faucet
for water purifier (softener), and check
there is no leakage around the filtering
system and piping.
●
The initial drainage time is an estimated
one until the bubbles disappear.
①
Open dedicated faucet for water purifier (softener) fully.
②
Adjust the water volume with dedicated stop valve for water
purifier (softener) .
200 ml
≒
quantity of 1cup of water
MP02-1E
…
Adjust the water flow volume to about 200 ml/sec
MP02-2E
…
Adjust the water flow volume to about 200 ml/sec
MP02-3E
…
Adjust the water flow volume to about 200 ml/sec
MP02-4E
…
Adjust the water flow volume to about 200 ml/2 sec
MP02-5E
…
Adjust the water flow volume to about 200 ml/2 sec
MP02-6E
…
Adjust the water flow volume to about 200 ml/2 sec
③
After the adjustment of water volume, close the faucet for water
purifier (softener).
Adjust the water flow volume
with this dedicated stop valve for
water purifier (softener).
※
This installation instruction manual has illustrations in case of using
dedicated faucet for filtered (softened) water.
①
②
③
Fixing nut
Plate
Frame plate
Dedicated faucet
for water purifier
(softener)
Dedicated stop
valve for water
purifier
(softener)
“OUT” side
“IN” side