Tele Radio Panther Installation Instructions Manual

Download PDF User Manual

Full Text Searchable PDF User Manual

Panther

Installation instructions

IM-PN-TX105-A04-EN

Language: English (original)

PN-T21-3
PN-T21-4
PN-T21-6
PN-T21-8
PN-T21-10

Transmitters

CONTENTS

CHAPTER 1: CUSTOMER INFORMATION

Thank you for purchasing a Tele Radio AB product

About this document

Warnings & restrictions

CHAPTER 2: PRODUCT DESCRIPTION

Transmitter front

Transmitter back

Technical data

Frequency band

CHAPTER 3: OPERATION

Start the transmitter

Switch the transmitter off

CHAPTER 4: CONFIGURATION SETTINGS

Radio mode

Automatic shutdown

Erase all transmitters from the receiver

Load select mode

CHAPTER 5: BATTERY GUIDE

Battery precautions

Battery information

Change batteries

CHAPTER 6: GUARANTEE, SERVICE, REPAIRS AND MAINTENANCE

CHAPTER 7: REGULATORY INFORMATION

CE marking

WEEE directive

FCC statement

IC Statement

ANNEX A: FREQUENT TERMS

CHAPTER 1: CUSTOMER INFORMATION

THANK YOU FOR PURCHASING A TELE RADIO AB PRODUCT

Read all instructions and warnings carefully before mounting, installing and
configuring the products.

These instructions have been published by Tele Radio AB and are not subject to any guarantee. The
instructions may be withdrawn or revised by Tele Radio AB at any time and without further notice.
Corrections and additions will be added to the latest version of the instructions. Always download the
installation instructions from our website, www.tele-radio.com, for the latest available version. Keep the
safety instructions for future reference.

IMPORTANT! These instructions are intended for installers. The instructions
containing information about the installation and configuration of the radio remote
control unit on the machine are not intended to be passed on to the end user

. Only

information that is needed to operate the machine correctly by radio remote control may be passed on
to the end user.

Tele Radio AB remote controls are often built into wider applications. Always refer to the applicable
local regulations for installation and safety requirements relating to cranes, hoists or other material
handling and/or lifting equipments using Tele Radio AB products, e.g.:

applicable local and industrial standards and requirements,

applicable occupational health and safety regulations,

applicable safety rules and procedures for the factory where the equipment is being used,

user and safety manuals or instructions of the manufacturer of the equipment where Tele Radio
AB remote control systems are installed.

Tele Radio AB instructions do not include or address the specific instructions and safety warnings of the
end product manufacturer.

For battery precautions, see "Battery precautions" on page 11.

Tele Radio AB products are covered by a guarantee/warranty against material, construction or
manufacturing faults, see "GUARANTEE, SERVICE, REPAIRS AND MAINTENANCE" on page 13

©Tele Radio AB
Datavägen 21
SE-436 32 ASKIM
SWEDEN
Tel: +46-31-748 54 60
www.tele-radio.com

- 3 -

ABOUT THIS DOCUMENT

Every care has been taken in the preparation of this manual. Please inform Tele Radio AB of any
inaccuracies or omissions.

These installation instructions cover general safety issues, main technical specifications, standard
installation, configuration and operating instructions, general troubleshooting and battery information.
Images shown in this document are for illustrative purposes only.

Term and symbol definitions

The capitalized terms and symbol used herein shall have the following meaning:

WARNING! indicates a hazardous situation which, if not avoided, could result in death or
serious injury.

CAUTION! indicates a hazardous situation which, if not avoided, will result in minor or
moderate injury.

IMPORTANT! is used for information that requires special consideration.

NOTE! is used to address practices not related to physical injury.

This symbol is used to call attention to safety messages that would be assigned the signal words
"WARNING" or "CAUTION".

WARNINGS & RESTRICTIONS

Carefully read through the following safety instructions before proceeding
with the installation, configuration, operation or maintenance of the product.
Failure to follow these warnings could result in serious injury and property
damage.

Installing, connecting and mounting

This radio system must not be used in areas where there is a risk of explosion.

Tele Radio AB remote controls are often built into wider applications. Those systems
should be equipped with:

a wired emergency stop where necessary.

a brake.

an audible or visual warning signal.

Always switch off all electrical power from the equipment before installation procedure.

Only licensed or qualified personnel should be permitted to install the product.

To utilize the safety of the system, use the stop relays in the safety circuitry of the object
that you want to control.

When the equipment controlled by the receiver's standard relays is connected via the
stop relays, make sure that the maximum current through the stop relays is still within
the specifications. Contact your representative for assistance.

Avoid registering transmitters in receivers where they are not being used.

- 4 -

Operation

Only qualified personnel should be permitted to access the transmitter and operate the
equipment.

Make sure that the user satisfies the age requirements in your country for operating the
equipment.

Make sure that the user is not under the influence of drugs, alcohol and medications.

Make sure that the user knows and follows operating and maintenance instructions as
well as all applicable safety procedures and requirements.

The user should:

always test the transmitter stop button before operating it. Press the stop button
then twist and pull it out. This test should be done on each shift, without a load.

never use a transmitter if the stop button is mechanically damaged. Contact your
supervisor/representative for service immediately.

never let the transmitter unattended.

always switch the transmitter off when not in use. Store in a safe place.

keep a clear view of the work area at all times.

Maintenance

Keep the safety instructions for future reference. Always download the configuration instruc-
tions from our website for the latest available version.

Always contact your representative for service and maintenance work on the product.

Write down the serial numbers/ ID codes of the receivers and transmitters used. This inform-
ation should be recorded in the “Settings document” for your product (can be downloaded from
www.tele-radio.com).

If error messages are shown, it is very important to find out what caused them. Contact your rep-
resentative for help.

The functionality of the stop button should be tested at least after every 200 hours’ use. Test the
stop button by pressing it and pulling it out.

If the stop button is mechanically damaged, do not use the transmitter. Contact your rep-
resentative for service immediately.

Before maintenance intervention on any remote controlled equipments:

always remove all electrical power from the equipment.

always follow lockout procedures.

- 5 -

CHAPTER 2: PRODUCT DESCRIPTION

TRANSMITTER FRONT

NOTE! Performing a “factory reset” of the unit will return the settings to the factory defaults and all
button remapping will be lost.

PN-T21-10

PN-T21-8

PN-T21-6

PN-T21-4

PN-T21-3

1. LED 1 (red)

2. LED 2 (red)

3. Top LED (red, green)

4. LED 3 (red)

5. LED 4 (red)

6. Button 1

7. Button 2

8. Button 3

9. Button 4

10. Button 5

11. Button 6

12. Button 7

13. Button 8

14. Button 9

15. Button 10

*On PN-T21-4, the default buttons 3, 4 and 6 have been remapped to work as buttons 2, 3 and 4.
Contact your representative for more details.

- 6 -

TRANSMITTER BACK

odel: 000000000

C ID: ABCD0000E

IC: 0000A

-B0000D

ele

-r

adio

1. I/O switch

2. Clip

3. Product label

I/O switch

The I/O switch on the back of the transmitter interrupts the power supply from the battery. When in the
O/off position, the transmitter cannot be started unless the charger plug is connected.

IMPORTANT! When the transmitter is to be transported by air, the I/O switch must be
in the O/off position.

NOTE! The I/O switch should not be used as an on/off button for the transmitter. To start and stop the
transmitter, use the stop button.

TECHNICAL DATA

PN-T21-10

PN-T21-8

PN-T21-6

PN-T21-4

PN-T21-3

Number of buttons

10 x 1-step
button

8 x 1-step
button

6 x 1-step
button

4 x 1-step
button

3 x 1-step
button

Battery

3 x 1.5 V AAA / LR03 Alkaline

I/O switch

Yes

Radio communication

Simplex

Dimensions

66 x 114 x 37.5 mm / 2.6 x 4.5 x 1.5 in

Weight

135 g / 0.29 lbs

Frequency band

2405–2480 MHz

Number of channels

16 (channel 11–26)

Radio frequency output
power

<10 mW

IP code

Operating temperature

-20…+55 °C / -4…+130 °F

- 7 -

FREQUENCY BAND

Channel

Frequency

2405 MHz

2410 MHz

2415 MHz

2420 MHz

2425 MHz

2430 MHz

2435 MHz

2440 MHz

2445 MHz

2450 MHz

2455 MHz

2460 MHz

2465 MHz

2470 MHz

2475 MHz

2480 MHz

- 8 -

CHAPTER 3: OPERATION

Do not perform this action when the receiver is in a session with another
transmitter. The radio communication may be interrupted or broken.

NOTE! Only keep the transmitters that you intend to use registered in the receivers.

NOTE! To establish a radio link between the transmitter and the receiver, both units must be set to the
same radio mode.

1. Press the receiver Function button.

The function LED lights (red).

2. Press the receiver Select button.

The relay LEDs light (red).

3. Press buttons 1 and 2. Keep pressed.

The relay LEDs light (red). The relay LEDs flash (red) 2 times.

4. Release buttons 1 and 2.

The relay LEDs flash (red) 1 time.
The transmitter is registered.

If no transmitter is found within approximately 10 seconds, the receiver exits to normal operation.

START THE TRANSMITTER

1. Start the transmitter by pressing any button on the transmitter.

The top LED lights (green when the battery capacity is good, red when the battery capacity is
poor).

SWITCH THE TRANSMITTER OFF

1. The transmitter switches off when no transmitter button is pressed.

- 9 -

CHAPTER 4: CONFIGURATION SETTINGS

RADIO MODE

NOTE! You cannot change the radio mode from the transmitter. Contact your representative for
assistance.

NOTE! To establish a radio link between the transmitter and the receiver, both units must be set to the
same radio mode.

This transmitter is set to discontinuous radio mode by default. The transmitter starts transmitting as
soon as the batteries are inserted and any transmitter button is pressed. Radio transmission ends when
all transmitter buttons are released.

AUTOMATIC SHUTDOWN

NOTE! Only for continuous radio mode.

NOTE! You cannot change the automatic shutdown time from the transmitter. Contact your
representative for assistance.

Automatic shutdown can save battery capacity by automatically switching the transmitter off following a
preset period of inactivity.

The transmitter automatic shutdown time is set to 3 minutes by default.

ERASE ALL TRANSMITTERS FROM THE RECEIVER

1. Press the receiver Function button.

The function LED lights (red).

2. Press the receiver Select button. Keep pressed (at least 4 seconds).

All relay LEDs light (red). All relay LEDs go out.

3. Release the receiver Select button.

All transmitters are erased from the receiver.

If the function LED flashes (red), one or more transmitters are still registered in the receiver.

LOAD SELECT MODE

NOTE! You cannot change the Load select mode from the transmitter. Contact your representative for
assistance.

Load select mode is deactivated by default (Load select mode 0).

- 10 -

CHAPTER 5: BATTERY GUIDE

BATTERY PRECAUTIONS

Carefully read through the following safety instructions and warnings before using,
charging or disposing of the batteries.

Batteries contain flammable substances such as lithium or other organic solvents, which may
result in overheating, rupture or combustion. Failure to read and follow the below instructions
may result in fire, personal injury and damage to property if charged or used improperly.

Handling and storage

Risk of explosion if battery is replaced with a battery of an incorrect type.

Do not short circuit, disassemble, deform or heat batteries.

Never attempt to charge a visibly damaged or frozen battery.

Do not use or charge the battery if it appears to be leaking, deformed or damaged in
any way.

Do not solder directly onto batteries.

Do not leave the battery in the charger once it is fully charged.

Store in a cool location. Keep batteries away from direct sunlight, high temperature,
and high humidity.

Immediately discontinue use of the battery if, while using, charging, or storing the bat-
tery, the battery emits an unusual smell, feels hot, changes color, changes shape, or
appears abnormal in any other way.

Keep batteries out of reach of small children. Should a child swallow a battery, consult
a physician immediately.

Disposal

When discarding batteries, insulate the + and - terminals of batteries with insulating/ masking tape.

Do not place multiple batteries in the same plastic bag.

Do not incinerate or dispose of batteries in fire.

Do not place used batteries in the household waste. Dispose of used batteries in accord-
ance with the applicable regulations and legal requirements.

Batteries that have been disposed of incorrectly may short circuit, causing them to
become hot, burst or ignite.

- 11 -

BATTERY INFORMATION

Do not recharge the batteries. Attempts to recharge may cause rupture or
hazardous liquids to leak, which will corrode the equipment.

NOTE! Electronics and batteries must be physically separated before disposal. Make sure that
electronics or batteries are not disposed of in household waste.

NOTE! When approximately 10 % of battery capacity remains, the top LED lights red.

CHANGE BATTERIES

Battery type: 3 x 1.5V AAA / LR03 Alkaline

1. Remove the back of the transmitter by unscrewing the 5 screws.

2. Replace the 3 x 1.5V AAA batteries. Use alkaline batteries for

optimal performance.

3. Screw the back of the transmitter into place.

- 12 -

CHAPTER 6: GUARANTEE, SERVICE, REPAIRS AND
MAINTENANCE

Tele Radio AB products are covered by a guarantee/warranty against material, construction and
manufacturing faults. During the guarantee/warranty period, Tele Radio AB may replace the product or
faulty parts. Work under guarantee/warranty must be carried out by Tele Radio AB or by an authorized
service centre specified by Tele Radio AB.

The following are

not

covered by the guarantee/warranty:

Faults resulting from normal wear and tear.

Parts of a consumable nature.

Products that have been subject to unauthorized modifications.

Faults resulting from incorrect installation and use.

Damp and water damage.

Maintenance:

Repairs and maintenance must be carried out by qualified personnel.

Only use spare parts from Tele Radio AB.

Contact your representative for service or any other assistance.

Keep the product in a clean, dry place.

Keep contacts and antennas clean.

Wipe off dust using a slightly damp, clean cloth.

NOTE! Never use cleaning solutions or high-pressure washer.

- 13 -

CHAPTER 7: REGULATORY INFORMATION

Applies to:

PN-T21-3, PN-T21-4, PN-T21-6, PN-T21-8, PN-T21-10

CE MARKING

Hereby, Tele Radio AB, declares that the radio equipment type(s) listed above is/ are in compliance with
Directive 2014/53/EU.

The latest version of the complete EU Declaration of Conformity is available on the Tele Radio AB
website, www.tele-radio.com.

WEEE DIRECTIVE

This symbol means that inoperative electrical and electronic products must not be mixed
with household waste. The European Union has implemented a collection and recycling
system for which producers are responsible. For proper treatment, recovery and recycling,
please take this product to a designated collection point.

Tele Radio AB strives to minimize the use of hazardous materials, promotes reuse and recycling, and
reduces emissions to air, soil and water. When a commercially viable alternative is available, Tele Radio
AB strives to restrict or eliminate substances and materials that pose an environmental, health or safety
risk.

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired
operation.

Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is con-
nected.

Consult the dealer or an experienced radio/TV technician for help.

To satisfy FCC RF exposure requirements, a separation distance of 20 cm or more should be maintained
between the antenna of this device and persons during device operation.

To ensure compliance, operations at closer than this distance is not recommended.

- 14 -

IC STATEMENT

This product complies with Industry Canada's licence-exempt RSSs. Operation is subject to the
following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation
of device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts
de licence. L’exploitation est autorisée aux deux conditions suivantes :

1. l’appareil ne doit pas produire de brouillage;

2. l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible

d’en compromettre le fonctionnement.

To satisfy IC RF exposure requirements, a separation distance of 20 cm or more should be maintained
between the antenna of this device and persons during device operation. To ensure compliance,
operations at closer than this distance is not recommended.

Afin d'assurer la conformité aux exigences de la IC en matière d'exposition aux RF, une distance de
séparation d'au moins 20 cm doit être maintenue entre l'antenne de cet appareil et toute personne à
proximité pendant le fonctionnement de l'appareil. Pour assurer le respect de ces exigences, il n'est pas
recommandé d'utiliser l'appareil à une distance inférieure à celle-ci.

- 15 -

ANNEX A: FREQUENT TERMS

Configuration ID

Numerical code stored in both the transmitter and receiver unit. The receiver unit
can only be controlled by a transmitter with the correct configuration ID.

Continuous radio
mode

When in continuous radio mode the transmitter unit transmits continuously when
it is switched on.

Custom ID

Numerical code stored in the transmitter unit, used to replace the unique ID code.
One or several transmitter units can be configured with the same custom ID and
the receiver will recognise them all as the same transmitter unit.

Discontinuous radio
mode

When in discontinuous radio mode the transmitter unit transmits whenever it is
switched on and a button is pressed. The transmission is interrupted when all but-
tons are released.

Function relay

Standard relay, controlled by the buttons on the transmitter unit.

Interlocking

Prevents a component from functioning when another component is functioning
or operating in a particular way.

Latching relay
functionality

The relay becomes active every time you press a button and remains active until
the button is pressed again.

Load select mode

One or more Load select modes are stored in the transmitter unit. Activating a spe-
cific Load select mode results in a group of preselected relays on the receiver unit,
which may be controlled from the transmitter unit.

Momentary relay
functionality

The relay will only be active while a button is pressed on the transmitter. When
the button is released, the relay will no longer be active.

On relay

Relay that is active when the receiver unit is operating and a radio link is estab-
lished, regardless of whether any other relays are active.

Operating mode

One or more Operating modes are stored in the receiver unit. Each Operating
mode describes which relays on the receiver unit are controlled when specific but-
tons on the transmitter unit are pressed.

Replace ID

Numerical code used to identify the transmitter during the Replace procedure.

Stop relay

Safety related relay controlled by the stop button on the receiver. Intended to inter-
rupt the power supply to a safety application controlled by the receiver unit.

Work relay

Relay that is active when any other specified relay(s) on the receiver unit is/are act-
ive.

Zero position check

Security function ensuring that potentially active buttons/joysticks upon start up
or lost/found radio links must be in the zero position before the system can be
used to avoid unplanned movements of the controlled object.

- 16 -

(This page has intentionally been left blank)

- 17 -

These installation instructions are subject to change without prior notice.

Download the latest installation instructions from

www.tele-radio.com

Ask a Question ?

PDF User Manual

PN-T21-3\ PN-T21-4\ PN-T21-6\ PN-T21-8\ PN-T21-10

Full Text Searchable PDF User Manual