Teka E/60.2 Installer Manual

Download PDF User Manual

Full Text Searchable PDF User Manual

Code N

: PRM-00-0001

Revised / Date

: 2006

NSTALLER

’

ANUAL

Page N

: 26 of 95

3 HOBS

When fitting a hob, installers should bear in mind the following series of important

recommendations in order to ensure the safety and correct working of the appliance:

During fitting, recessed hobs should be handled with care to prevent damage to the edges

or the glass surface of vitroceramic models.

With vitroceramic models, carefully check the glass surface to ensure there are no cracks.

Should there be even the slightest crack, do not proceed with installation.

If the hob is to be recessed over an oven, carefully follow all specifications indicated to
ensure correct ventilation.

Before installing, ensure that the gas supply characteristics are compatible with the
regulations indicated on the specification plate (gas type and pressure).

Installation and maintenance of the hob should be carried out by qualified personnel in
accordance with existing regulations.

Cabinet adhesives should be resistant to temperatures of 100

C (Y type protection against

overheating, in compliance with the EN 60335-2-6 standard).

Minimum distances between the hob and extractor hood should be strictly observed: 65 cm

for electric hobs 70 cm for gas and mixed hobs.

Recess measurements should be similarly observed.

Recessed hobs with reinforced plates should be installed more than 15 cm away from side

walls. All other hobs should be installed at a distance of more than 10 cm.

The hobs referred to in this installation manual are compatible with TEKA ovens. In this

case consult the corresponding manual before installing.

The installation process does not differ much from model to model. Below are installation
instructions for each model in the range with both independent and ME controls and for gas,

electric and mixed models.

Code N

: PRM-00-0001

Revised / Date

: 2006

NSTALLER

’

ANUAL

Page N

: 27 of 95

3.1 I

NSTALLATION OF HOB

E/60.2

AND

ES/60.2

E/50

(1) Minimum distance to wall

(2) Minimum ventilation distance

(2)Minimum ventilation distance

(3) Space for recess

Code N

: PRM-00-0001

Revised / Date

: 2006

NSTALLER

’

ANUAL

Page N

: 28 of 95

SM AND CG, EC AND CGC, ECC

(1)

Minimum distance to wall

(2) Minimum ventilation distance
(3) Space for recess

CG LUX 70

CG LUX 60

Code N

: PRM-00-0001

Revised / Date

: 2006

NSTALLER

’

ANUAL

Page N

: 29 of 95

VITROCERAMIC HOBS

(1) Minimum distance to wall

(2) Minimum ventilation distance

(3) Space for recess

Depending on the model in question, the recessing system is designed for cabinets with a work

surface thickness of 20, 30 and 40 mm. In the event that a separation board is not required, the

TT 620

TR 620

TR 620, TZ620 AND TR640

TR 620, TZ620 AND

TR640

Code N

: PRM-00-0001

Revised / Date

: 2006

NSTALLER

’

ANUAL

Page N

: 30 of 95

induction models n

s IR/IT 635, IR/IT 645 and IR 735 include a suplementary casing which shoud

be fitted when installing the appliance under a drawer.

Code N

: PRM-00-0001

Revised / Date

: 2006

NSTALLER

’

ANUAL

Page N

: 31 of 95

Plate N

TR 932

Plates N

s VI TC 60 2I AND VI TC 60 4I

1. Minimum distance between adjacent walls
2. Interior cut measurement
3. Exterior cut measurement
4. External measurement of worksurface

Minimum distance between ajacent walls

2. Interior cut measurement
3. Exterior work surface measurement

Code N

: PRM-00-0001

Revised / Date

: 2006

NSTALLER

’

ANUAL

Page N

: 32 of 95

IR 622, IZ 622, IT622

(1) Minimum distance to wall

(2) Minimum ventilation distance

(3) Space for recess

NOTE: Induction hobs should not be installed above an oven that does not feature forced
ventillation.

The installation process is the same as for vitroceramic
hobs, bearing in mind it will be necessary to take

greater precautions to ensure improved ventilation for
the recess space.
Ventilation openings will need to be thermally isolated

using the insulating blanket supplied with the hob.
This insulating blanket prevents hot air mixing with the

cold air being sucked in.

Warning!

This blanket must not cover ventilation

outlets, preventing the evacuation of air.
Avoid excessive heat build up in the hob.

Code N

: PRM-00-0001

Revised / Date

: 2006

NSTALLER

’

ANUAL

Page N

: 33 of 95

3.2 F

ITTING THE HOB TO ITS RECESS

-{}-

Cristal Gas Series

-{}-

C - Serie Soft plate

B - How to fit this plate in a 60cm
cabinet

D - 60 cm cabinet

E - Detail

The minimum vertical distance from
the hob to the cabinet is 600 mm.

The fitting process is identical to that for other
models.

1) Attach seal

“

”

2) Fix the four clips

“

”

using the two tabs

“

”

in the spaces

“

”

in the hob.

3) Tighten the screws

“

”

See illustration.

Code N

: PRM-00-0001

Revised / Date

: 2006

NSTALLER

’

ANUAL

Page N

: 34 of 95

For models N

s CG.1 4G, CG.1 3G1P and Vitroceramics:

(1)

Self threading screw for kitchen cabinets with a thickness of 20 mm or 30 mm

For model N

CGC AI AL:

CGC 4G AI AL plate and Soft Series:

Fig. 4

Insert the push nuts into the screw

housings (See figure 13).

Having

attached

the

clip

which

corresponds to the thickness of the

surface (20, 30 or 40mm), fully tighten all

screws.

Key :

–

Leaktight seal

–

Work surface

C - Screw

–

Attachment clip

–

Push nut

Step 2

After

checking

that

the

cabinet

measurements

are

correct,

necessart to attach the leaktightness
seale (J) under the hob.

Step 3

Place the clips (K) as shown in the

illustration (fig. 15) attaching them to
the gaps in the lower part of the

housing with the 4.2mm thread screws.

The clips, seal and screws are all
supplied with the appliance.

Place the attachment clips as

shown in the illustration (fig. 12)

If thickness is equal to 30mm,

use self threading screws (M5)

Code N

: PRM-00-0001

Revised / Date

: 2006

NSTALLER

’

ANUAL

Page N

: 35 of 95

In the

600x510 series

, the procedure for fitting the plate is identical to other procedures.

Fig. 5

For the

EX/70 series

, the fitting process is as follows:

-{}-

Turn the hob and correctly position the adhesive

side of the the seal

“

”

(see fig.) around the edge.

The ends of the seal should be joined together

without overlapping.

Place the hob in the space.

Attach with the clips

“

”

, carefully introducing the

tab into the slot

“

”

on the bottom of the hob.

Tighten screw

“

”

until it holds clip

“

”

to the cover

(see illustration).

This hob is designed to be recessed into

worktop surfaces with a thickness of 20, 30
or 40 mm.

Attach the leaktight seal

“

”

underneath the

hob.

Fix the four clips

“

”

using the two tabs

“

”

in the spaces

“

”

in the hob.

Next, place the hob in the space and tighten

the screws

“

”

of the 4 clips with the

corresponding key.

Code N

: PRM-00-0001

Revised / Date

: 2006

NSTALLER

’

ANUAL

Page N

: 36 of 95

TR 932

When the hob is fitted into kitchen cabinets, the installer needs to ensure that there is no contact
between the bottom of the hob and the cabinet. In order to guarantee this it is necessary to fit

some protection which may only be removed with tools.

The back of the lower cabinet needs to feature an opening in order that air may freely circulate.

The wood on the front of the cabinet shoud be removed to ensure an opening that will allow air to

reach the inside of the space where the hob is located.

The distance between the hob and the cabinet should be large enough to ensure sufficient
ventilation.

This protection should be placed at least 20 mm
from the bottom of the hob so that the mains

electric supply cable does not come into contact

with the hob.

Carefully position the hob in the recess
space and attach with the respective

clips. Tighten the screws until it is

correctly fixed in place.

For all models with bevelled edges, before

installing the hob it is necessary to remove any
remains of material and check that the seal is

correctly in place. It is also important that silicone
is not used as there is a risk of breakage when

dismantling.

Code N

: PRM-00-0001

Revised / Date

: 2006

NSTALLER

’

ANUAL

Page N

: 37 of 95

3.3 F

IXING CARDANS IN CONTROL

FREE HOBS TO OVEN

TEKA

Rear view of control panel

1) Disconnect the electrical supply.
2) Remove the telescopic attachments by pushing

the small button marked PUSH (A) with the point

of a screwdriver until it can be pulled out a few
centimetres.

3) Remove the four fasters from the ends.

Partially insert the oven into the space in the
instalation, bearing in mind that the cardan on

the hob should not be moved. A space needs to
be left in order to be able to insert the other end

of the cardan into the back part of the control

panel, and then attaching the fasteners.

5) For electrical connection, connect the hob to the

oven.

6) Place the oven carefully into the recessed

opening and check that the cardans are

correctly connected.

7) Attach the contols to the oven

’

s control panel.

In order for the controls to work correctly, press

in and then turn to free them from the safety

catch.

If the cardans are too short it is possible to attach an
elongation.

C bl d

Code N

: PRM-00-0001

Revised / Date

: 2006

NSTALLER

’

ANUAL

Page N

: 38 of 95

With respect to the CGC 4G AI AL hob

Connecting the hob to the oven is carried out in the same way as before, apart from step 7, which
needs to be altered:

7) Fit the oven trim as instructed in the accompanying manual. Take care to fit the trim correctly.

3.4 G

AS CONNECTION

We would like to remind you once more that connecting the hob to the gas supply should always
be carried out in strict accordance with current installation regulations.

The appliance should be installed in a kitchen that is adequately ventilated, as stipulated in the

current installation regulations.

The hob should be connected to the gas supply via a metal tube. This tube should be placed in

order that it does not touch any moving part of the cabinet or other electrical appliances.

It should be situated in a place where it cannot be obstructed and where its entire length, which

should not exceed 2 metres, may be inspected.

The hob is equipped with a

½”

diametre connection, in compliance with the ISO 228-1 standard.

10/12mm copper tubing is also supplied, which should be soldered to the gas supply pipe. Each

time the connecting nut is dismantled, the joint should be changed.

In order to prevent damage to the hob, when tightening the nut on the gas supply pipe, use a tool

with a maximum grip of 350Kgf/cm.

Once the appliance has been connected to the gas, check it for leaktightness. If you intend to do

this with compressed air, bear in kind that test pressure should not exceed 200g/cm

. In the event

that the test is carried out with gascheck tightness with water and soap.

NEVER USE A NAKED

FLAME!

Minimum flame adjustment

Once the hob has been correctly fitted, check that the minimum flame level is well regulated. In
order to do this, light the gas rings and turn the control quickly from maximum to minimum. If the

flame goes out, they will need to be adjusted.

Code N

: PRM-00-0001

Revised / Date

: 2006

NSTALLER

’

ANUAL

Page N

: 39 of 95

3.5 E

LECTRICAL CONNECTION

Before connecting the hob to the mains supply, check that the voltage and frequency correspond

to the characteristics on the specification panel (situated underneath the appliance).
Ensure that the connection to the mains supply is at the correct voltage.
Mains supply should be provided via a suitable omnipolar switch with a 3mm miminum gap

between contacts and which can carry the required maximum ampage, ensuring that disconnection
in case of emergency or appliance cleaning is guaranteed.
Take care to ensure that the mains supply cable is not in contact with the hob casing.
For those models which do not include a mains supply cable, in order to connect the appliance,

remove the cover situated underneath the hob in order to gain access to the connection terminal.

Having successfully connected the appliance, replace the cover and secure the mains cable with a
jubilee clip in order to prevent pressure on the cable.
The mains supply cable should be at least the H05 VVF type.

Possible electrical connections

TR 932

Induction

Code N

: PRM-00-0001

Revised / Date

: 2006

NSTALLER

’

ANUAL

Page N

: 40 of 95

CONTROL PANEL

4.1 INSTALLATION

LUX glass control panels

Exterior measurements of the panel:

597x120mm

Glass control panels

Exterior measurements of the panel:

560x85mm

Make an opening in the kitchen cabinet with the
following measurements: 557 / 565 mm long, 95 /

110mm high.
Screw in the two fixing plates so that the shafts can

be inserted into the control panel. The left hand

plaque should be placed in such a way that the semi
circle appears on the upper side of the plate, whilst

the hand side plaque should appear with the semi
circle on the lower side of the plate.
To connect the hob to the control panel, insert the

hob connector into the back of the panel.
Attach the cardans.
Insert the panel, introducing it from right to left into
the shafts of the fixing plate.

Make an opening in the kitchen cabinet with the
following measurements: 527x 70 mm.
Screw in the two fixing plates so that the shaft can
be inserted into the control panel.
To connect the hob to the control panel, insert the

hob connector into the back of the panel.
Attach the cardans.
Insert the panel, introducing it from right to left into
the shafts of the fixing plates.

Code N

: PRM-00-0001

Revised / Date

: 2006

NSTALLER

’

ANUAL

Page N

: 41 of 95

Metallic control panels

For all models, a minimum opening of
50 cm

is needed to ensure adequate

ventilation

Make an opening in the kitchen cabinet with the following

measurements: 435 x 70 mm.
To make this opening, draw the outline and the

attachment holes with the paper stencil supplied with the
panel.
Attach the plate with 4 screws so that the higher part is to

the right.
Insert the panel from right to left within the the plate that

has just been attached.
Check that the panel is in the correct place and finish

attachment.
To connect the hob to the control panel, insert the hob
connector into the back of the panel.
Attach the cardans.

Code N

: PRM-00-0001

Revised / Date

: 2006

NSTALLER

’

ANUAL

Page N

: 42 of 95

Models IR/IT 635, IR 735 and IR/IT 645 feature new casings manufactured from synthetic glass
fibre which allow for a reduction in the height of the hob, improving their installation above other

electrical appliances such as ovens, dishwashers or even closed drawers.

Ask a Question ?

PDF User Manual

ES/60.2 E/50 SM CG EC CGC ECC CG LUX 60 TR 620 TZ620 TR640 TR 932 IR 622 IT622

Full Text Searchable PDF User Manual