TekPower TP3016M Series User Manual - User Manual

Download PDF User Manual

Full Text Searchable PDF User Manual

User Guide

TP3016M Series

Switching Mode DC Power Supply

Introduction

I. Quick Start

1.1 Front Panel Description

1.2 Pre-Checking

1.3 Quick Start

1.4 Output Checking

II. Specifications

2.1 Major Specification

2.2 Supplementary Characteristic

III. Operation

3.1 Keypad

3.2 Front Panel

3.3 Voltage Setting

3.4 Current Setting

3.5 Output Switch

3.6 Data Saving Operation

3.7 Recall Saving Operation

3.8 USB Power Charging

IV. Calibration

4.1Voltage Calibration

4.2 Current Calibration

Introduction

Thank you for selecting the TP3016M Switching DC Power Supply, please read this user guide before
the operation.

Safety

This manual contains important safety and operation instructions for correct use of power supply.
Read through the manual and pay attention to the markings and labels of this unit to be connected.

Do not install the substituted spare parts or operate the modification without permission, please
send the unit back for A/S to our authorized dealers or factory for guaranty of the stability of the unit.

Pay special attention to the information of WANRINGS or CAUTIONS to avoid the damage to power
supply or connected equipment and human injured.

Please contact the trained technicians for repair service.

Safety Marks

WARNING:

Failure to observe this warning may cause injury to persons and damage to power supply or
connected equipment.

CAUTION:

Failure to observe this warning may result in damage to equipment and improper functioning of
power supply.

Grounding

High Voltage

Attention on the Warning or Caution

Specification Compliance

TP3016M Switch mode DC Power Supply is compliance with the specification described in this manual.

The content or specification of this manual is subject to change, without prior notice.

Product Features

TP3016M is the single output switch mode DC power supply with max. 30V output voltage, 1.6A
output current and max. output power as 50W.

TP3016M is integrating the AC/DC and DC/DC 2nd level voltage regulator technology, the AC/DC
input is adapting the worldwide voltage range. The DC/DC is using the synchronous buck mode, which
with the high efficiency and high speed dynamic response performance.

TP3016M can be set the voltage and current through the keypad of front panel and save the setting
groups for further performance.

TP3016M also has the 4 digit voltage and current meter, as well as the fantastic handheld size. The
TP3016M is perfect for solving a variety of loading conditions and applications.
Please find the following main features of TP3016M:

●

Handheld design

●

Without noise of fan

●

4 digits LCD display

●

Output short circuit protection

●

High speed dynamic response

●

Once power cut-off, automatically protect under power off status

●

The output has the automatic recognition of USB charging port

●

Can be calibrated via software operation

I. Quick Start

This chapter describes the basic check points on TP3016M for making sure the proper operation, as
well as the functions of TP3016M.

1.1

Front Panel Description

1 – Current Setting Indicator
2 – Voltage Setting Indicator
3 – Measured Value Display
4 – Keypad
5 – USB Charging Ports
6 – DC Output Terminals

1.2 Pre-Checking

Before the operation, please check the accessories are fully included, if any missing, please contact
the local distributor.

□

Power Cord – 1PC (Compliance with the standard voltage of the region)

□

User Guide – 1PC

Connect with power and switch on TP3016M, the unit start the self-system checking, the LCD displays
0.5s, date of manufacturing, production lot, model number version number in turn.

1.3 Quick Start

OUT Button

Press and light

OUT

button, the power supply is under output status and read the measuring value of

voltage or current in the display. Press again OUT button to exit output function.

UP Arrow Key + DOWN Arrow Key

Press

arrow key to activate the LCD backlit

Press

DOWN

arrow key to exit the LCD backlit

LEFT Arrow Key + RIGHT Arrow Key

Press LEFT arrow key to decrease the contrast of LCD

Press

RIGHT

arrow key to increase the contrast of LCD

V/A Key

Press the

V/A

key to activate voltage measurement and read the voltage value from display.

Push the

V/A

key again to switch current measurement and read the current value from the display

USB Button

Push and light the

USB

button and adjust voltage to 5.2V and the current as 3A to enter USB

power charging mode; then, push and light the

OUT

button, the TP3016M is working as

power charger.

Push the USB button again and USB button lights out to exit USB power charging mode.

SET Button

V/A Button

+ Direction Arrow Keys

Push the

SET

button, by pressing the direction arrow keys to adjust the voltage value setting, Push

the

V/A

button to switch the current value setting mode, by pressing the direction arrow keys to

measured current value.

1.4 Output Checking

1.41 The output voltage regulation mode check

This is for checking the functions of power supply under non-load voltage stability.

1)

Switch on the product, the power is off and the indicators of CC & CV are light off.

Push and light the

OUT

button, the indicator of CV is light on at LCD display.

Setting the voltage of power supply
Push the

V/A

button and shift to voltage display mode, adjust various voltage values then, check

the voltage value displayed at LCD is approaching the settled voltage value and within the
tolerance, current value is showed as 0A.

Make sure the voltage can be adjusted from 0.5V to max. 30V.

1.42 The output constant current mode check

This is for checking the functions of power supply under constant current mode.

1)

Switch on the product, the power is off and the indicators of CC & CV are light off.

Adjust voltage value as 30V.

Connect the resistance (3Ω/50W) between output terminals.

Push and light the

OUT

button, the indicator of CC is also light.

Setting the current of power supply
Push

V/A

button and shift to current display mode, adjust various current values, then, check the

current value displayed at LCD is approaching the settled current value and within the tolerance.

Make sure the current can be adjusted from 0A to the max. value.

1.43 The output short circuit protection check

This is for checking the function of short circuit protection of output.

Switch on the product, the power is off and the indicators of CC & CV are light off.

Adjust voltage value is over 5V and current value is over 1A.

Push and light the

OUT

button.

Connect the output terminals by wire for short circuit, the light of

OUT

button is off and output

off.

1.44 The USB charging function check

This is for checking USB charging function.

1)

Switch on the product, the power is off and the indicators of CC & CV are light off.

Push and light the

USB

button. Adjust the voltage as 5.1V and current as 2.0A.

Push and light

OUT

button.

Make sure the power supply under CV mode, the CV indicator is light in LCD.

Setting the current value and make sure the current value can be adjusted from 0A to the max.
value of measuring range. Do not adjust voltage.

II. Specification

2.1 Major Specification

Input Voltage

110AC~ 60Hz

Input Current

Output Rating

Voltage range

0.5V~30V

Current range

0~3.75A

Line Regulation

％

of output + offset

Voltage

≦

0.01%+3mV

Current

≦

0.01%+3mA

Load Regulation

％

of output + offset

Voltage

≦

0.02%+3mV

Current

≦

0.02%+3mA

Measurement Accuracy

Voltage

10mV

Current

1mA

Measured Value Accuracy
@ 25

℃

％

of output + offset

Voltage

≦

0.05%+5mV

Current

≦

0.05%+5mA

Measurement Speed

Voltage

100ms/ones

Current

100ms/ones

Setting Value Accuracy @
25

℃

％

of output + offset

Voltage

≦

0.05%+5mV

Current

≦

0.05%+5mV

Ripple and Noise
20HZ-20MHZ

Voltage

≦

10mVrms/100mVp-p

Current

≦

10mVrms/100mVp-p

Temperature Coefficient
@ 0~40

℃

±%of output + offset

Voltage

≦

0.05%

Current

≦

0.1%

Dimensions

185x88x38 mm

Weight (Net )

370g

2.2 Supplementary Characteristic

Build-in EEPROM
Recommended Calibration Time

：

1 Time/Year

AC Input Power: 110VAC, 60 Hz

Operating Temperature: 0 to 40

℃

Storage Temperature: -20 to 70

℃

III. Operation

Check the rating label of the power supply and ensure that it complies with the AC mains voltage that
is to be used.

Connect the power supply to the AC minas using the provided power cord.

3.1 Keypad Description

OUT

Output check

V/A

Voltage & Current Shift

USB

5V Cell Phone Charging

SET/ENTER

Voltage & Current Setting/Enter

STORE/RECALL

Data Saving/Recall

DOWN

LEFT

RIGHT

Direction Arrow Keys

3.2 Front Panel

After power on, the panel operation mode is the default setting of power supply and all the
functional buttons can be operated.

3.3 Voltage Setting

The voltage setting range is from 0.50V to 30V; follow the setting steps as below:

Switch on the power supply

Push the

OUT

button to stop the output setting and light off

OUT

button

Push and light the

SET/ENTER

button, the max. value position is flickering of voltage setting area

Push the

LEFT

RIGHT

arrow keys to move the cursors

Push the

DOWN

arrow keys to change the settings

Push

SET/ENTER

button and light off this button to exit voltage setting mode

ENTER

OUT

SET

0 0.0 0

V ------------- >

3 0.0 0

V ---------------> OK

Remark:

I.

It is possible to set voltage values once the outputs are valid. However, for protection of the
load, it is recommended to stop output before voltage setting.

II.

Due to the total power limit, current settings might be decreased automatically once
voltage setting increasing.

3.4 Current Setting

The current setting range is from 0.000A to 1.66A, follow the setting steps as below:

Switch on the power supply

Push the

OUT

button to stop the output setting and light off

OUT

button

Push and light the

SET/ENTER

button, the max. value position is flickering of voltage setting area.

Push the

V/A

button, the max. value position of current setting is flickering and current setting is

activated

Push the

LEFT

RIGHT

arrow keys to move the cursors

Push the

DOWN

arrow keys to change the settings

Push

SET/ENTER

button and light off this button to exit current setting mode

ENTER

OUT

SET

V/A

0. 000

A --------->

2.000

A ------------ > OK

Remark:
I.

It is possible to set current values once the outputs are valid. However, for protection of the
load, it is recommended to stop output before current setting.

3.5 Output Switch

Under the panel operating mode, by pushing

OUT

button to shift output status. Once

OUT

button

lighted, the measured values displayed at LCD; push

OUT

button again to exit output mode.

3.6 Data Saving Operation

Under the voltage setting or current setting mode, push the

STORE

button to save the values of

voltage or currents into memory of power supply for future recall purpose. (as below steps)

Refer 3.3 or 3.4 for voltage or current setting mode.

Push

STORE

button to enter data saving mode, the min. value position is flickering and displayed

STORE

icon in LCD.

Move

DOWN

arrow keys to select storage group serial number.

Click

ENTER

button to confirm data saving, click

STORE

button to exit data saving mode.

SET

STORE

ENTER

-----> OK

3.7 Recall Saving Operation

Under the panel operating mode, push the

RECALL

button for getting the saved data from memory;

follow the setting steps as below:

1.

Switch on the power supply

Push

RECALL

button to enter data recall mode, the min. value position is flickering and displayed

RECALL

icon in LCD.

Move

DOWN

arrow keys to recall the stored group serial number, the default values from

voltage or current setting mode displayed in LCD.

Click

ENTER

button to confirm data recall, click

STORE

button to exit data recall mode.

RECALL

ENTER

--------> OK

3.8 USB Power Charging

Push the

USB

button and light the green indicator, the default setting is voltage @ 5.1V and current

@ 2.0A, the LCD will display 5.1V, current value also can be as 0A. Connect the mobile phone via USB
cable for power charging.

The USB ports are suitable for both android mobile phone and l Iphone, with automatic check
function, the product can set the proper charging current automatically.

1.

Push and light the

OUT

button to activate output mode.

Push the

USB

button and

USB

indicator is off to exit USB charging mode.

USB

OUT

IV Calibration

Follow the below chart, connect the 5 digit displayed volt meter, current meter, resistance
(10Ω/100W) into the output terminals, calibration follow the steps start from point of zero voltage -
voltage coefficient – current zero – current coefficient.

Hold the

SET

button to switch on power supply till “

REF

” displayed in LCD to enter calibration mode.

4.1 Voltage Calibration

At the power supply displayed

2.000A

05.00V

in setting area of LCD and

**.**V

displayed in main

part of LCD. Connect the output terminal with an external reference voltage meter and shift to CV
mode. Hold the

LEFT

RIGHT

arrow keys to move the cursors to left or right and push the

DOWN

arrow keys to adjust the values same as readings of external reference voltage meter, then

click

ENTER

button to finish the voltage bias calibration.

At the power supply displayed

2.000A

30.00V

in setting area of LCD, hold the

LEFT

RIGHT

arrow

keys to move the cursors to left or right and push the

DOWN

arrow keys to adjust the values

same as readings of external reference voltage meter, then click

ENTER

button to finish the voltage

gain calibration.

4.2 Current Calibration

Push the

V/A

button and power supply displayed

0.500A

20.00V

in setting area of LCD and

*.***A

displayed in the main part of LCD. Connect the output terminals with the external reference current
meter and the load (6Ω/100W), shift to CC mode. Hold the

LEFT

RIGHT

arrow keys to move the

cursors to left or right and push the

DOWN

arrow keys to adjust the values same as readings of

the external reference current meter, then click

ENTER

button to finish the current bias calibration.

At the power supply displayed

3.000A

20.00V

in the setting area of LCD, hold the

LEFT

RIGHT

arrow keys to move the cursors to left or right and push the

DOWN

arrow keys to adjust the

values same as readings of external reference voltage meter, then click

ENTER

button to finish the

current gain calibration.

Push

OUT

button to exit and restart the power supply to complete the calibration function.

Ask a Question ?