Teeter Hang Ups EP-950 Assembly Instructions Manual - User Manual

Download PDF User Manual

Full Text Searchable PDF User Manual

Inversion Table

Assembly Instructions

EP-950

1. It is your responsibility to familiarize yourself with the

proper use of the equipment and the inherent risks of

inversion, such as falling on your head or neck, pinching,

entrapment or equipment failure.

2. This product is not designed for persons over 6’6” (198

cm) or over 300 lbs (136 kg). Structural failure could occur

or head/neck may impact

oor during inversion. Serious

injury or death could result.

DO NOT

use the equipment without a licensed physician’s

approval and a review of the medical contraindications, as

noted in the Owner’s Manual.

4. Failure to assemble and/or use the equipment as directed

may void the manufacturer’s warranty on this product and

could result in injury or death.

DO NOT

use the inversion table until you have thoroughly

and carefully read the Owner’s Manual, viewed the

DVD, reviewed all other accompanying documents, and

inspected the equipment.

6. Choose a level surface for assembling and operating the

table.

7. Follow each step in sequence. Do not skip ahead.
8. Make sure that all fasteners are secure.
9.

ALWAYS

test and inspect the table. Make sure the table

rotates smoothly to inverted position and back.

10. Replace defective components immediately and/or keep

the equipment out of use until repair.

PRE-ASSEMBLY

Before you begin:

Review all steps before beginning assembly and read

all precautions before using the inversion table. Carefully adhere to the

Assembly Instructions and Owner’s Manual to help ensure user safety

and product integrity.

WARNING

ITEMS FOR ASSEMBLY

Carefully remove the individual parts from the carton. You should have all

of the items listed below. If any items are missing or damaged, contact

Customer Service at 1-800-847-0143.

PRE-ASSEMBLY

Items for Assembly Item Numbers

A-frame Base

(EP-1100)

EZ-Angle Tether

(F5-1008)

Table Bed Assembly

(EP-1140)

Bolts and Nuts

(EP-1149)

Head

Pillow (EP-1105)

Main Shaft with

Ankle Lock System

(IA-1107)

Front Ankle Assembly

Ankle

Bar (F5-1047)

Rubber Plugs (2)

(F5-1056)

Foam Rollers (2)

(F5-1051)

Bolt

Sleeve (IA-1110)

Sleeve

Screw

(IA-1112)

Rear Bar Assembly

Rear Bar w/

Heel

Cups (IA-1113)

Bolt/Nut

(IA-1116)

Rubber Plug

(F5-1056)

Foot Platform

Assembly

Foot

Bar

(IA-1119)

Foot Pieces (2)

(IA-1118)

Screw

(IA-1123)

Screwdriver (F5-1130)

Over EZ Handles

Left Handle

(GL-9518)

Right Handle

(GL-9522)

Threaded Bolts (4)

(GL-9523)

Shrouds

(GL-9524)

1/4” Bolts (4)

(GL-9525)

Roller Hinges (2)

(TR-1001)

Wrenches (2)

(F5-1088)

Allen Wrench

(EP-1150)

(EP-1100)

(EP-1140)

(EP-1105)

(GL-9524)

(GL-9525)

(TR-1001)

(F5-1088)

(IA-1149)

(EP-1149)

(F5-1008)

Teeter

Hang

Ups

EP-950

(GL-9518)

(IA-1107)

(F5-1047)

(F5-1051)

(IA-1110)

(IA-1113)

(IA-1116)

(IA-1119)

(IA-1118)

(IA-1112)

(F5-1056)

(IA-1123)

(F5-1056)

(GL-9522)

(F5-1130)

Bolts will

come pre-

assembled

in handles

and

shrouds.

(EP-1150)

(GL-9523)

Before Beginning

Before reading further, study the drawing below to familiarize yourself

with the important components of your new Teeter Hang Ups

inversion table.

ASSEMBLY

Table Bed

A-frame

Main Shaft

Ankle Lock

System

Adjustable

Foot Platform

Over EZ-Handles

Stability Feet

Rear and

Front Ankle

Clamps

EZ-Angle

Tether Strap

Teeter

Hang

Ups

EP-950

Crossbar

Traction Handles

ASSEMBLY

Step One

Assemble the A-frame Base

(EP-1100) and Install the

Handles

(GL-9518, GL-9522)

and Shrouds (GL-9524)

• Open the A-frame and make sure

the spreader arms are locked.
Rest the A-frame on the

oor

(Figure 1). The Crossbar is at the
front.

• Insert two double threaded bolts

(GL-9523) through the base of
the Left Handle (marked with
an “L”) and hand tighten on the
outside with the nuts provided.
(See Figure 2) Line up and insert
the opposite end of the bolts
through the corresponding 1/3”
holes on the outside of the hinge
plate. Loosely tighten with nuts,
then use the wrenches provided
to tighten both sets of nuts,
being careful not to over tighten.
Repeat with the Right Handle.

• Place each shroud over the

outside edge of the corresponding
handle. Line up and insert the
shroud bolts (GL-9525) through
the smaller 1/4” holes in the
hinge plate (See Figure 2). Use
the wrenches provided to tighten
the nuts, being careful not to over
tighten.

Figure 1

Figure 2

spreader arms

front

back

Teeter

Hang

Ups

EP-950

Crossbar

Right

Left

Figure 2A

NOTE: Nuts and bolts may
be packaged separately or

assembled in

handles and shrouds.

( L )

Step Two

Attach the Upper Support

Arms to the Table Bed

(EP-1141)

• Before following this step, make

sure you have read the orange
insert that came attached to the
Table Bed.

• Place the Table Bed face down

on the

oor and push down on

the Support Beam, so the two
holes align evenly with holes
at the base of Upper Support
Arms (Figure 3). You may have
to exert extra pressure to ensure
the Support Beam slides over the
rubber spacers.

• Insert the two bolts (EP-1149)

through the rubber spacers and
into the open holes.

• Fasten each bolt with a nut.

• Use the Allen Wrench to steady

(EP-1150) the bolts, tighten the
nut onto the bolt with the larger
wrench (F5-1088) (Figure 4).
Repeat with the second bolt.

ASSEMBLY

Figure 3

Figure 4

Teeter

Hang

Ups

EP-950

Support Beam

Upper Support Arms

ASSEMBLY

Step Three

Install the Roller Hinges

(TR-1001) onto the Table Bed

(EP-1140)

• For ease-of-assembly, rest the

Table Bed against the side of the
A-frame (Figure 5).

• Open the Cam Locks on each side

of the Table Bed (Figure 5A).

• With the Pivot Pins facing

outward, insert the Roller Hinges
into the brackets on each side of
the Table Bed. The Roller Hinges
must slide between the Cam
Locks and the brackets.

• Make sure the Roller Hinges are

in the same hole setting on both
sides. Figure 6 shows the Roller
Hinges engaged correctly in
setting C.

• Push down on the Cam Locks

(Figure 6A) to secure the hinges.

NOTE: Refer to the Owner’s

Manual for an explanation of the
hole settings. If you are unsure,
use setting C to start.

Teeter

Hang

Ups

EP-950

A B C

Figure 6A

Figure 6

Figure 5A

Pivot Pin

Figure 5

ASSEMBLY

Step Four

Attach the Table Bed

(EP-1140) to the

A-frame (EP-1100)

• Holding each side near the

Roller Hinges, pick up the
Table Bed and stand at the
front of the A-frame where
the Crossbar is located. Lower
each Pivot Pin into the A-frame
hinge plates one at a time
(Figure 7). You may need to
push outward on the A-frame
in order to slide the second
Pivot Pin into the hinge. Figure
9 shows the correct placement
of the Pivot Pin into the hinge
plate.

• Make sure that both Pivot Pins

are seated at the base of the
slot in the hinge plate. Check
to make sure that the self-
locking hooks have closed over
both Pivot Pins (Figure 9), and
the table rotates smoothly.

WARNING

Failure of the self-locking hooks to close over both Pivot Pins is indication of

improper assembly and if not corrected, could result in serious injury or death!

Figure 9

Figure 7

Teeter

Hang

Ups

EP-950

Figure 8

ASSEMBLY

Step Five

Insert the Main Shaft (IA-1107) into

the Table Bed (EP-1140)

• Loosen the De-rattler knob on the Main

Shaft Housing.

• With the height adjustment settings on

the Main Shaft facing up, slide the end
of the Main Shaft into the Main Shaft
Housing on the Table Bed.

• Pull out the height-selector locking pin

to allow the Main Shaft to slide in
farther (Figure 10). For the purpose of
easy assembly, slide in the Main Shaft
and release the pin in the last height
setting (Refer to the Owner’s Manual
for proper height adjustment before
use).

NOTE: The De-rattler knob is an

optional accessory that helps prevent
a slight shift in the table when you
invert. The security of the product is
not compromised if you choose not to
tighten the knob.

• The Main Shaft must rest against the

Crossbar of the A-frame
(Figure 11). The Crossbar prevents
the table from rotating forward when
the user steps on the Foot Platform.
If the Main Shaft does not rest on the
Crossbar as shown in Figure 11 then
the Table Bed has been assembled
backwards onto the A-frame and this
must be corrected before use.

Figure 10

Teeter

Hang

Ups

EP-950

De-rattler Knob

Main Shaft

Housing

Height-Selector

Locking Pin

Figure 11

Crossbar

Step Six

Install the Front Ankle Assembly

• Gather the Ankle Bar (F5-1047),

Black Plugs (F5-1056), Foam

Rollers (F5-1051), Bolt Sleeve

(IA-1110), and Sleeve Screw (IA-

1112).

• Stand in front of the Main Shaft

and slide the Ankle Bar over the

ratchet housing into the slot

(Figure 12).

• Align the bolt holes. Insert the

Bolt Sleeve through the holes

and secure with the Sleeve

Screw (Figure 13).Position one

Allen Wrench on the Sleeve

Screw and one on the Bolt

Sleeve to tighten.

• Slide the Foam Rollers over each

side of the Ankle Bar (Figure 14).

• Insert the Black Plugs into both

ends of the Ankle Bar (Figure

14).

Figure 14

Figure 13

Figure 12

Ratchet Housing

Allen Wrench

ASSEMBLY

Teeter

Hang

Ups

EP-950

ASSEMBLY

Step Seven

Install the Rear Bar Assembly

•

With the rounded corners

of the rear foam Heel Cup

facing down, insert the Rear

Bar with one Heel Cup (IA-

1113) into the large hole

at the bottom of the Main

Shaft (Figure 15).

• Insert the Bolt (IA-1116) to

secure the Rear Bar to the

Main Shaft, and attach the

nut with the wrenches (F5-

1088) provided (Figure 16).

• Slip the other Heel Cup

(rounded corners down) onto

the Rear Bar and push the

Rubber Plug (F5-1056) into

the Rear Bar (Figure 17).

Figure 15

Figure 16

Figure 17

Teeter

Hang

Ups

EP-950

ASSEMBLY

Step Nine

Attach the EZ-Angle Tether Strap

(F5-1008) to Limit the Degree of

Rotation

• Hook the clip at the end of the tether

strap to the loop at the base of the
table bed (Figure 20) to limit your
degree of rotation.

• See the Owner’s Manual insert for

further instructions on adjusting the
strap.

Figure 20

Teeter

Hang

Ups

EP-950

Step Eight

Install the Foot Platform

Assembly

• Slide the Foot Bar (IA-1119)

with one Foot Piece (IA-

1118) in the hole below the

ratchet (Figure 18).

• Slide the Foot Piece onto the

Bar (Figure 19).

• Insert the screws (IA-1123)

onto the Foot Platform and

tighten with the screw driver

(F5-1130) (Figure 19).

Note:

The Foot Pieces are

designed with a High and

Low setting. Position in the

Low setting (screws facing

up) for ease of assembly.

Refer to Owner’s Manual for

a description of the settings.

Figure 18

Figure 19

Low Setting

ASSEMBLY

CHANGING THE ROLLER HINGE SETTING

•

Stand with your legs on either side of the Main
Shaft.

• Reach under each Roller Hinge with your index

ngers. Use your thumbs to release the locks over

the Roller Hinges (See Figure 21).

• Lift both sides of the table out of the A-frame at

the same time. You may rest the table on the
Crossbar of the A-frame.

• Unlock the Cam Locks for each Roller Hinge.

Change the Roller Hinges to the desired setting (A,
B or C) (Figure 22).

• Re-lock the Cam Locks. Replace the Roller Hinges

into the hinge plates of the A-frame.

MAINTENANCE

•

To clean the Table Bed, wipe down with a damp
cloth. Do not use abrasive cleaners.

STORING THE INVERSION TABLE

• Loosen the De-rattler knob.

• Pull the height-selector locking pin and slide the

Main Shaft in all the way to the

nal hole setting.

Engage the pin in the storage setting.

• Rotate the table opposite from use until the table

has turned 180 degrees and rests against the
Crossbar on the A-frame.

•

Pull up on the spreader arms to fold the
A-frame (Figure 23).

WARNING: This operation

may pinch

ngers if not done slowly and carefully.

Figure 22

Read the Owner’s Manual thoroughly before using your Teeter Hang Ups

Inversion Table. Improper settings could result in serious injury or death!

WARNING

ADJUSTMENTS / MAINTENANCE / STORAGE

Teeter

Hang

Ups

EP-950

A B C

Figure 21

Figure 23

If you have any problems assembling the equipment,

or questions about its use, please contact customer service at:

USA:

Teeter

9902 162

St. Ct. E., Puyallup, WA 98375

Toll Free (Phone) 800-847-0143 (Fax) 800-847-0188

Local (Phone) 253-840-5252 (Fax) 253-840-5757

mail@teeter-inversion.com

www.teeter-inversion.com

International:

Inversion International, Ltd.

PO Box: AP 59245

New Providence Island, Bahamas

(Phone) +1-242-362-1001 (Fax) +1-242-362-1002

mail@InversionInternational.com

www.InversionInternational.com

U.S. patents apply.

Teeter Hang Ups is a registered trademark of Teeter

Speci

cations subject to change without notice.

International Law Prohibits Any Copying, EP-2021; 0108-0

Classi

ed as Medical Equipment, Part I in accordance with

UL 60601-1 and CAN/CSA C22.2; General Requirements for Safety in

accordance with Underwriters Laboratories, Inc.

Any Modi

cation to this device will void the UL Classi

cation.

Ask a Question ?