Teeter Contour Power Assembly Instructions Manual - User Manual

Download PDF User Manual

Full Text Searchable PDF User Manual

Inversion Table

Assembly Instructions

*Inversion Table images may

vary slightly from your model.

Contour Power

HANG U

YEAR

ARRANT

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING THE INVERSION TABLE.

WARNING

SAVE THESE INSTRUCTIONS

FAILURE TO FOLLOW INSTRUCTIONS AND WARNINGS COULD RESULT IN SERIOUS INJURY OR DEATH.

BEFORE YOU BEGIN:

Review all steps before beginning assembly and read all precautions before using the inversion table.

Carefully adhere to the Assembly Instructions and Owner’s Manual to help ensure safety and product integrity.

Read and understand all the instructions, view the instructional video, review all other accompanying documents, and inspect the

equipment before using the inversion table. It is your responsibility to familiarize yourself with the proper use of this equipment

and the inherent risks of inversion, such as falling on your head or neck, pinching, entrapment, or equipment failure. It is the

responsibility of the owner to ensure that all users of the product are fully informed about the proper use of the equipment and all

safety precautions.

DANGER

- To reduce the risk of electrical shock:

• Always unplug the appliance from the electrical outlet immediately after using and before cleaning.

WARNING

- To reduce the risk of burns, fire, electric shock, or injury to persons:

• An appliance should

NEVER

be left unattended when plugged in. Unplug from outlet when not in use, and before putting on or

taking off parts.

•

DO NOT

operate under blanket or pillow. Excessive heating can occur and cause fire, electric shock, or injury to persons.

• Close supervision is necessary when this appliance is used near children, or by or near invalids, or disabled persons.

• Use this appliance only for its intended use as described in this manual.

DO NOT

use attachments not recommended by the

manufacturer.

•

NEVER

operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged,

or dropped into water. Return the appliance to a service center for examination and repair.

•

DO NOT

carry this appliance by supply cord or use cord as a handle.

• Keep the cord away from heated surfaces.

•

NEVER

operate the appliance with the air openings blocked. Keep the air openings free of lint, hair, and the like.

•

NEVER

drop or insert any object into any opening.

•

DO NOT

use or store product outdoors.

•

DO NOT

operate where aerosol (spray) products are being used or where oxygen is administered.

•

DO NOT

use if you are over 6 ft 6 in (198 cm) or over 300 lbs. (136 kg). Structural failure could occur or head/neck may impact

the floor during inversion.

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING THE INVERSION TABLE.

WARNING

SAVE THESE INSTRUCTIONS

FAILURE TO FOLLOW INSTRUCTIONS AND WARNINGS COULD RESULT IN SERIOUS INJURY OR DEATH.

BEFORE YOU BEGIN:

Review all steps before beginning assembly and read all precautions before using the inversion table.

Carefully adhere to the Assembly Instructions and Owner’s Manual to help ensure safety and product integrity.

•

DO NOT

operate where aerosol (spray) products are being used or where oxygen is administered.

•

DO NOT

use if you are over 6 ft 6 in (198 cm) or over 300 lbs. (136 kg). Structural failure could occur or head/neck may impact

the floor during inversion.•

DO NOT

allow children to use this machine.

• Keep body parts, hair, loose clothing and jewelry clear of all moving parts.

• To disconnect, turn all controls to the off position, then remove plug from outlet. To unplug, grasp the plug, not the cord.

• Connect this appliance to a properly grounded outlet only. See Grounding Instructions.

CAUTION

- To Reduce The Risk Of Injury From Moving Parts – Unplug Before Servicing.

WARNING

- To Reduce The Risk Of Electric Shock – Unplug Before Cleaning or Servicing.

WARNING

- To reduce the risk of injury to persons:

• The inversion table has no user serviceable parts.

• This product is intended for indoor home use only.

DO NOT

use in any commercial, rental or institutional setting.

•

DO NOT

use the equipment without a licensed physician’s approval and a review of the medical contraindications, as noted in the

Owner’s Manual.

• Failure to assemble and/or use the equipment as directed may void the manufacturer’s warranty on this product and could result

in injury or death.

• Choose a level surface for assembling and operating the table.

• Follow each step in sequence.

DO NOT

skip ahead.

• Make sure that all fasteners are secure.

•

ALWAYS

test and inspect the table. Make sure the table rotates smoothly to inverted position and back.

•

ALWAYS

replace defective components immediately and/or keep the equipment out of use until repair.

• Keep cord away from heated surfaces.

•

DO NOT

handle plug or appliance with wet hands.

• Keep children away from extended foot support (or other similar parts).

•

ALWAYS

activate the Safety Lock when not in use. Remove the Safety Key and store in secure location.

Grounding Instructions

•

This product must be grounded. If it should malfunction or break down, grounding provides a

path of least resistance for electric current to reduce the risk of electric shock. This product

is equipped with a cord having an equipment-grounding conductor and a grounding plug.

The plug must be plugged into an appropriate outlet that is properly installed and grounded

in accordance with all local codes and ordinances.

DANGER

Improper connection of the equipment-grounding conductor can result in a risk

of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to

whether the product is properly grounded. Do not modify the plug provided with the product -

if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

•

This product is for use on a nominal 120-V circuit, and has a grounding plug that looks like

the plug illustrated in sketch A in Figure 1. A temporary adapter that looks like the adapter

illustrated in sketches B and C in Figure 2, may be used to connect this plug to a 2-pole

receptacle as shown in sketch B if a properly grounded outlet is not available. The temporary

adapter should be used only until a properly grounded outlet (sketch A) can be installed by a

qualified electrician. The green colored rigid ear, lug, or the like extending from the adapter

must be connected to a permanent ground such as a properly grounded outlet box cover.

Whenever the adapter is used, it must be held in place by a metal screw.

FIGURE 1

FIGURE 2

Unpacking Instructions

FIGURE 3

Follow these important unpacking instructions to properly remove the parts from the box and

avoid damage to your new inversion table.

IMPORTANT:

The Table Bed Assembly is heavy – be sure to complete this step with two people.

• Remove all cardboard and packing materials from the box.
• To disengage the Table Bed from the A-Frame, carefully

LIFT the support beam high enough

to clear the Crossbar and Rubber Bumper on the A-Frame. Then, slide

BACK

and separate

the Table Bed Assembly from the A-Frame (Figure 3).

• Set the Table Bed Assembly to the side and continue unpacking.
• Be sure to remove protective plastic from all items prior to assembly.

TIP:

Unpack materials and prepare to set up your Contour Power Inversion Table in its

permanent location. Keep in mind that you will require an electrical outlet to power your table.

Support Beam

Crossbar

Items for Assembly

A-Frame
FlexTechnology

Table Bed

Head Pillow

Bolts, Washers & Nuts (2)

Chicago Post and Bolt (2)

Pan Head Bolts (4)

Decompression Arch

Adjustable Acupressure Nodes (4pk)

Main Shaft

with

Deluxe EZ-Reach

Ankle Lock System

Hand Grips

Safety Keys (2)

Tools

10/13mm Wrenches (2)

5mm Allen Wrench

CP-1100
CP-1300

EP-1105

EP-1149

CP-0038

CP-1128

IA-1650

E6-1374

NX-1620

P1-1015
CP-1250

F5-1088

IA-1149

ITEMS FOR ASSEMBLY

ITEM NUMBER

Items are not shown to scale.

CP-1300

CP-1100

CP-1128

EP-1105

EP-1149

IA-1149

NX-1620

CP-1250

F5-1088

P1-1015

CP-0038

IA-1650

E6-1374

Before reading further, study the drawing below to familiarize yourself with the

important components of your new Teeter Hang Ups

inversion table.

Before Beginning

Head Pillow

FlexTechnology

Table Bed

Rotation Control Button
Motor Housing

Safety Keys

Handles
Spreader Arms

De-Rattler Knob
Height-Selector Locking Pin

Main Shaft
Crossbar
A-Frame
Deluxe EZ-Reach

Ankle Lock System

Ankle Comfort Dial

1
2
3

5
6
7
8
9
10
11
12
13

WARNING LABEL PLACEMENT

Important: Please review all labels and supporting materials before using your inversion table.

We hope you enjoy your new Teeter Hang Ups Inversion Table!

If you have any questions, please contact our Customer Service Department at 1.800.847.0143 or www.teeter-inversion.com.

This drawing indicates the locations

of the warning labels found on your product.

If a label is missing, illegible or is removed,

contact Customer Service at the phone number

or website found at the bottom of this page to

request a complimentary replacement label.

Note: Image and labels below

not shown at actual size.

IA-2007-M

WARNING

AVERTISSEMENT/ ADVERTENCIA

Ankles must be properly secured before use.

REPLACE LABEL IF DAMAGED, ILLEGIBLE, OR REMOVED.

Les chevilles doivent etre convenablement a obtenu avant l’usage.

REMPLACER L'ETIQUETTE SI ENDOMMAGE OU ENLEVE.

Los tobillos deben estar propiamente asegurados antes de usarse.

REEMPLACE LA ETIQUETA SI ESTÁ DAÑADA O SE HA PERDIDO.

WARNING/ AVERTISSEMENT/ ADVERTENCIA

TIPPING HAZARD

: For upright storage, leave A-Frame open wide enough to remain stable, or secure to the wall to prevent tipping. In households with

small children, the table should be stored flat on the floor, not upright.

DANGER DE RENVERSEMENT:

Pour un rangement en position verticale, laissez le cadre en A suffisamment ouvert pour qu'il reste stable,

ou appuyez-le sur un mur pour éviter les chutes. Dans les foyers avec de jeunes enfants, cette table devrait être rangée à plat sur le sol et non

pas debout.

PELIGRO DE DESLIZAMIENTO:

Para guardar la tabla parada, deje la estructura A lo suficiente abierta para que quede estable, o asegúrela a la

pared para prevenir que se deslice y caiga. En casa con niños pequeños, la tabla debe guardarse acostada sobre el piso, no parada.

NX-1750-M 0910-1

REPLACE LABEL IF DAMAGED, ILLEGIBLE, OR REMOVED. REMPLACER L'ETIQUETTE SI ENDOMMAGE OU ENLEVE.

REEMPLACE LA ETIQUETA SI ESTÁ DAÑADA O SE HA PERDIDO.

WARNING

AVERTISSEMENT/ ADVERTENCIA

Remove key when not in use and store out of the reach of children.

REPLACE LABEL IF DAMAGED, ILLEGIBLE, OR REMOVED.

Enlevez la clé lorsque l’appareil n’est pas utilisé et conservez-la hors de portée des enfants.

REMPLACER L'ETIQUETTE SI ENDOMMAGE OU ENLEVE.

Cuando no esté en uso retire la llave y guárdela fuera del alcance de los niños.

REEMPLACE LA ETIQUETA SI ESTÁ DAÑADA O SE HA PERDIDO.

CP-1770 0311-1

WARNING

- To reduce the risk of personal injury or death:

•

Read and understand all the instructions before using the inversion table. It is your

responsibility to familiarize yourself with the proper use of the equipment and the inherent

risks of inversion, such as falling on your head or neck, pinching, entrapment or

equipment failure.

•

Do not allow children to use the machine.

•

Keep children, bystanders, and pets away from the machine while in use.

•

Keep body parts, hair, loose clothing and jewelry clear of all moving parts.

•

Height/ Weight capacity: 4ft 8in - 6ft 6in (142-198 cm); 300 lbs (136 kgs).

•

This product is for indoor household use only.

•

DO NOT

use below garage floor or grade level.

DANGER

To reduce risk of electric shock, always unplug this appliance from the electrical

outlet before cleaning.

WARNING

To reduce the risk of burns, fire, electric shock, or injury to persons:

•

DO NOT

leave unattended when plugged in. Unplug before putting on or taking off parts.

•

NEVER

operate if it has a damaged cord or plug, or if it has been dropped or damaged.

Contact the manufacturer for evaluation.

•

DO NOT

attempt to fix this appliance if damaged.

•

NEVER

operate the appliance with the air opening blocked.

•

Connect this appliance to a properly grounded outlet only.

GROUNDING INSTRUCTIONS

This product must be grounded. If it should malfunction or breakdown, grounding

provides a path of least resistance for electric current to reduce the risk of electric shock.

This product is equipped with a cord having an equipment-grounding conductor and a

grounding plug. The plug must be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes and ordinances.

DANGER

- Improper connection of the equipment-grounding conductor can result in a risk

of electric shock. Check with a qualified electrician or serviceman if you are in doubt as

to whether the product is properly grounded. Do not modify the plug provided with the

product - if it will not fit the outlet have a proper outlet installed by a qualified electrician.
This product is for use on a nominal 120v AC 60Hz 1a circuit* and has a grounding plug.

Make sure that the product is connected to an outlet having the same configuration as

the plug. No adapter** should be used with this product.

*Unless otherwise specified due to special order

**For outside USA only: use a certified, grounded adapter.

WARNING

Replace Labels if Damaged, Illegible, or Removed.

www.teeter-inversion.com, www.inversioninternational.com

CP-1725 0511-0

Step 1

Back

Front

Right

Left

Right

Left

FIGURE 4

FIGURE 5

Crossbar

Spreader Arms

Open the A-Frame (CP-1100).

• To stand the inversion table A-Frame upright, first move it onto its side (Figure 4), and

then carefully lift it up onto its feet.

• Open the A-frame wide enough so that it is stable and can stand upright on its own

(Figure 5).

• Lock the Spreader Arms to secure the legs into position.

Step 2

Install the Table Bed Assembly (CP-1300) to the A-Frame (CP-1100)

IMPORTANT:

The Table Bed Assembly is heavy - be sure to complete this step with two people.

• Lift the Table Bed Assembly (CP-1300) and hold in inverted position.
• Lower the Table Bed Assembly so the back of the Table Bed rests behind the Crossbar

(Figure 6), and place the shrouds on either side of the motor housing onto the top of the

A-Frame.

• Using the Allen Wrench (IA-1149), secure one Chicago Post & Bolt (CP-0038) to the side of

the shroud (Figure 7), and two Pan Head Bolts (CP-1128) to the front of the shroud (Figure 8).

Complete on both sides.

FIGURE 6

Crossbar

FIGURE 7

FIGURE 8

Step 3

Attach the Upper Support Arms to the Table Bed (CP-1300).

• Leave the Table Bed in the inverted position.
• Push on the Support Beam on the back of the Table Bed Assembly so that the two holes

align evenly with the holes at the base of the Upper Support Arms (Figure 9). You may have

to exert extra pressure to ensure that the Support Beam slides over the Rubber Spacers.

• Insert the two bolts (EP-1128) into the open holes (Figure 9).
• Fasten each bolt with a washer and nut (Figure 10).
• Use the Allen Wrench (IA-1149) to steady each bolt and tighten the nuts using the 10/13 mm

open end Wrench provided (F5-1088) (Figure 10).

FIGURE 9

Support Beam

Upper Support Arms

Rubber Spacers

FIGURE 10

Step 4

Insert the Main Shaft (NX-1620) into the Table Bed (CP-1300).

• Plug in the power supply. Be sure that the Hand Crank is not engaged in the motor and that

the Safety Lock has been turned off (Figure 11). See Step 6 for more information on the

Safety Lock.

NOTE:

he Safety Lock Key will remain in the lock when disabled and the table is in use.

• Rotate the bed upright to the horizontal position (

Figure 12) by pressing forward (towards

Ankle System) on the Rotation Control Button on the Motor Housing.

• Loosen the De-Rattler Knob at the base of the Main Shaft Housing.
• With the height adjustment settings on the Main Shaft facing up, insert the end of the Main

Shaft into the Main Shaft Housing at the base of the Table Bed (Figure 13).

• Pull out the Height Selector Locking Pin to allow the Main Shaft to slide in further,

then release the pin to engage a hole. (Refer to the Owner’s Manual for proper height

adjustment before use.)

NOTE:

The De-Rattler Knob is an optional feature that prevents a slight shift when you

invert. Product security is not compromised if you choose to not tighten the knob.

•

Finish rotating the bed upright to its “start” position. The Main Shaft must rest against the

Crossbar of the A-frame (Figure 14). If the Main Shaft does not rest on the Crossbar as

shown in Figure 14 then the Table Bed has been assembled backwards onto the A-frame

FIGURE 11

Safety Key

Hand Crank

FIGURE 12

De-Rattler Knob

Main Shaft Housing

Height-Selector Locking Pin

Crossbar

Proper Resting Position

FIGURE 13

FIGURE 14

Step 5

Attach the Hand Grips (P1-1015) to the Table Bed (CP-1300) Assembly

• Insert a Hand Grip into the receiving end of the Table Bed Asssembly, located near the

Motor Housing (Figure 15).

• Screw in the handle and tighten (Figure 16).
• Repeat with the other handle.

FIGURE 15

FIGURE 16

Step 6

WARNING

Read the Owner’s Manual lthoroughly before using your Teeter Hang Ups

Inversion Table. Improper settings could result in serious injury or death!

Safety Lock and Key (CP-1250)

• The Safety Lock allows the table to be deactivated without the need to unplug

the power supply.

• Insert the Safety Key (CP-1250) and turn clockwise to disable the Safety Lock and engage

the motor. The Safety Key will remain in place when the table is in-use (Figure 17).

• Upon completion of your inversion session, turn the Safety Key counterclockwise, remove

from the Motor Housing and store in a secure place for future use.

Before Use

• Check that the Safety Lock (Figure 17) is disabled.
• Test the table rotation by pressing the Rotation Control Button (Figure 18).
• Test the Hand Crank by following the instructions on page 4 of the Owner’s Manual.

Disengage the Hand Crank after testing.

• Ensure that all fasteners are secure.
• Please register your warranty online at www.teeter-inversion.com
• For your reference, the serial number can be found on the back of the Table Bed Main

Shaft Housing.

FIGURE 17

FIGURE 18

Safety Keys

FIGURE 20

Tipping Hazard: For upright storage, leave A-frame open wide

enough to remain stable, or secure to the wall to prevent tipping.

In households with small children, the inversion table should be stored

flat on the floor, not upright.

WARNING

Maintenance

• Unplug the inversion table before performing maintenance.
• To clean the Table Bed, wipe down with a damp cloth.
• Do not use abrasive cleaners.

Storing the Inversion Table

• Loosen the De-Rattler Knob.
• Pull the height-selector locking pin, slide the Main Shaft in all the way, and engage the pin

in the storage setting.

• By pressing the Rotation Adjustment Button, rotate the Table Bed to its fully inverted

position until it reaches the Crossbar (Figure 19).

• Unplug the inversion table before storing.
• Pull up on the Spreader Arms to fold the A-Frame (Figure 20), leaving the A-Frame legs

open to a width of at least 12” for stability.

CAUTION:

Proceed carefully. This product is heavy. Folding the A-Frame may pinch

fingers if not done cautiously.

• Be sure to leave the A-Frame partially open, as to prevent tipping.
• Ensure that the electrical cord has been properly stored while not in use.

FIGURE 19

Maintenance / Storage

U.S. and Foreign Patents Pending. Teeter Hang Ups is a registered trademark of Teeter.

Specifications subject to change without notice.

CP-1705 0712-2

Any modification to

this device will void

the UL Listing.

MDSS GmbH

Schiffgraben 41

30175 Hannover, Germany

REP

If you have any problems assembling the equipment, or questions about its use, please contact customer service at:

USA: Teeter

Toll Free (Phone) 800-847-0143

(Fax) 800-847-0188

info@teeter-inversion.com

www.teeter-inversion.com

International: Inversion International, Ltd.

(Phone) +1-242-362-1001

(Fax) +1-242-362-1002

info@InversionInternational.com

www.InversionInternational.com

Ask a Question ?