Tecnosicurezza T6530/DL User Instructions

Download PDF User Manual

Full Text Searchable PDF User Manual

U S E R I N S T R U C T I O N S

IU_BasicLine_01_eng

T6530/DL

T8530

EM35•20 Technical Manual

CHARACTERISTICS

The StraightBolt lock can be mounted in all four mounting directions. The Basic Electronics

feature a 6-digit Main code that can be changed by the user. With the main code a secondary

code can be activated and deleted. If a valid code has been entered, the lock electronic removes

the blocking for 3 seconds and the bolt can be moved into the housing by turning an internal

driving cam with a turnable entry unit or a knob. After moving the bolt to LOCKED position, the

StraightBolt automatically secures.

ENTRY UNITS

The StraightBolt is compatible with the following NL LOCK Entry units (separate technical

descriptions for Entry units are available). Entry unit spindle/cable hole on the safe door does not

have to exceed 12 mm diameter

EM35•20 Technical Manual rev. 160223

Delta Series: DE20

Bravo: BR50

Premier: PI20

(with separate knob)

DE20-10 Technical Manual

CHARACTERISTICS

The Delta is a low profile electronic entry with “soft touch“ rubber keypad and metal
ring to be mounted with StraightBolt lock. Cable length is approximately 30 cm.
Additional battery box is required (sold separately).

DIMENSIONS / MOUNTING INSTRUCTION

The diameter of the cable hole should be minimum 9 mm, maximum 12 mm. The
hole must be de-burred well to avoid damage to the cable.
Drill and tap door according to picture 1 drawing for the mounting plate

•

Fit the mounting plate (1) on door
using the 2x M4 mushroom-head
supplied screws (2) with "UP TO
ROTATE" oriented upwards

•

Cut spindle (5) length to exceed
8-10 mm lock mounting surface

•

Insert spindle in keypad so that
cable runs in the spindle groove.

•

Fit spring (4) and detent pin (3)
into the hole on the rear of the
keypad

•

Route the spindle through the
cable/spindle hole and move the
unit to the mounting adapters.
Rotate keypad 35-40° CCW until keypad can be fixed on the screw heads and
then rotate CW to straight up. Proceed with installing the lock.

The Delta entry unit can now not be removed!

DE20•10 Technical Manual rev. 110128

Delta

StraightBolt

Bolt work requirements
Lock bolt operations only allowed as described
into the drawing and max load should not
exceed 1KN.

Important:
•

Modifications to the lock (including lock bolt attachments) are not
allowed, and will void the manufacturer’s warranty and Standards
approvals.

•

No through holes on the safe door are allowed within the lock body area beside
the spindle/cable hole.

•

Lock body area should be protected against destructive attacks

DE20xx

EM35•20 Technical Manual

CHARACTERISTICS

The StraightBolt lock can be mounted in all four mounting directions. The Basic Electronics

feature a 6-digit Main code that can be changed by the user. With the main code a secondary

code can be activated and deleted. If a valid code has been entered, the lock electronic removes

the blocking for 3 seconds and the bolt can be moved into the housing by turning an internal

driving cam with a turnable entry unit or a knob. After moving the bolt to LOCKED position, the

StraightBolt automatically secures.

ENTRY UNITS

The StraightBolt is compatible with the following NL LOCK Entry units (separate technical

descriptions for Entry units are available). Entry unit spindle/cable hole on the safe door does not

have to exceed 12 mm diameter

EM35•20 Technical Manual rev. 160223

Delta Series: DE20

Bravo: BR50

Premier: PI20

(with separate knob)

DE20-10 Technical Manual

CHARACTERISTICS

DIMENSIONS / MOUNTING INSTRUCTION

•

Fit the mounting plate (1) on door
using the 2x M4 mushroom-head
supplied screws (2) with "UP TO
ROTATE" oriented upwards

•

Cut spindle (5) length to exceed
8-10 mm lock mounting surface

•

Insert spindle in keypad so that
cable runs in the spindle groove.

•

Fit spring (4) and detent pin (3)
into the hole on the rear of the
keypad

•

The Delta entry unit can now not be removed!

DE20•10 Technical Manual rev. 110128

Delta

StraightBolt

Bolt work requirements
Lock bolt operations only allowed as described
into the drawing and max load should not
exceed 1KN.

Important:
•

Modifications to the lock (including lock bolt attachments) are not
allowed, and will void the manufacturer’s warranty and Standards
approvals.

•

No through holes on the safe door are allowed within the lock body area beside
the spindle/cable hole.

•

Lock body area should be protected against destructive attacks

Br50xx

ST40xx

EM2050/A

EM3550/A

EM3550/A/S (not VdS)

IU_BasicLine_01_eng

LOCK FEATURES

Codes

One Manager

: can open, changes his code, manage users, program time delay, audit

users and lock.

User

: can open and change their own codes.

New codes are rejected when less than 2 digits are different from existing codes.

Time Delay

Time delay programmable from 0 (no time delay) to 99 minutes. Open window from 1 to 19
minutes.
During time delay enabled LED flashes at two seconds intervals. Open window is indicated
by LED then buzzer at 1 seconds intervals alternately (once LED, once beep).

Battery low warning

If battery low (<6V) during motor activation, multiple beeps.

Time penalty

When entering code, a time penalty of 5 minutes will be started after the 4th consecutive
wrong code entered. During time penalty, LED flashes at 10s interval, no access possible
to lock.
Any key pressed during time penalty emits a long beep.
After time penalty, two consecutive wrong codes will start it again.

Additional features

TD override user #9 – When TD active, user #9 always override TD in “dual mode”.
Basic Input/Output features – If standard I/O is activated, silent alarm (+1 on combination
last digit will trigger an alarm output signal) and disable input features are active through
additional 4-wires on-board connector.

Recommandations

•

It is strongly recommended to immediately change the factory codes

•

For security reasons, do not chose codes which could be easy to guess (e.g. 1 2 3

4 5 6)

•

For your new code, do not use any personal data like birthdays or any other data,

that could be derived by knowledge of your person.

•

After code changing, the lock must be tested several times with door in open state.

•

Do not open the lock case, otherwise you compromise the function of the lock and

warranty will be void.

•

In order to prevent any possibility that the code become public or known by

unauthorized persons we strongly recommend to store any data and/or code in a
safety place, where only its rightful owner can access.

IU_BasicLine_01_eng

USERS INSTRUCTIONS

Open

•

Enter a six digits valid code (factory code 1-2-3-4-5-6).

A valid code is followed by a double signal.

An invalid code is followed by a long signal.

•

If time delay is not active open the door.

•

If time delay is active the counting starts (during time delay counting the light flashes

every 2 seconds). When time delay elapses, open window counting starts (during
open window counting the buzzer beeps every 2 seconds). Enter the code again and
open the door.

•

Note: If the door is not opened within 3 (three) seconds, the lock secures

automatically.

Manipulation protection

•

The entry of 4 (four) consecutives invalid codes, will cause a 5 (five) minutes lock

blocking. During this period, the light flashes every 10 seconds and any key pressed
will produce a long signal. After expiration, the entry of 2 (two) more invalid codes,
will restart the 5 minutes blocking period.

Change code

Press and hold

key “0” until double signal.

Enter the old code (double signal).

Enter the new code (double signal).

Repeat the new code (double signal).

Note: In case of errors (long signal) the old code remains valid.

Always perform this operation with the door opened.

Test lock operation several times before closing the door.

Add the user

Press and hold

key “1” until double signal;

the light remains switched on during the
following actions.

Enter the main code.

Enter the new opening code (double signal).

Confirm the new opening code (double

signal).

Note: If the lock features only two codes there will not be the need to select a position for

the new user.

IU_BasicLine_01_eng

Delete the user

Press and hold

key “3” until double signal;

the light remains switched on during the

following actions.

Enter the main code.

The user is now deleted.

Membrane check-up

Press and hold

key “5” until double signal.

Enter the following sequence of numbers:

1-2-3-4-5-6-7-8-9-0.

Double signal = key correctly working.

Long signal = key not working.

Set time delay

Press and hold

key “9” until double signal;

the light remains switched on during the

following actions.

Enter the main code.

Enter time delay value (2 digits, from 00 to 99 minutes) and open window value (2

digits, from 01 to 19 minutes) (double signal).

For instance if you want to program 26 minutes delay and 12 minutes open

window, enter: “2612”.

Confirm time delay value and open window value (double signal).

Note: Time delay value can be increased in every moment; to decrease it, lock must be in

open window.

Battery change

A series of signals during opening indicates that the battery is weak and must be replaced.
Only use fresh 9V-ALKALINE batteries from brand name manifacturers like DURACELL

IU_BasicLine_01_eng

Before operating the unit,

please read this manual thoroughly,

and retain it for future reference.

Correct disposal of this product:

(Waste Electrical & Electronic Equipment)

Applicable in the European Union and other European countries with separate
collection systems.

This marking shown on the product or its literature indicates that it
should not be disposed with other wastes at the end of its working

life. To prevent possible harm to the environment or human health

from uncontrolled waste disposal, please separate this from other
types of wastes and recycle it responsibly to promote the sustainable

reuse of material resources.

Certified ISO 9001 : 2000

TECNOSICUREZZA s.r.l.

Via Cesare Battisti, 276 – 37057 S. Giovanni Lupatoto (VR) – Italy

Tel. +39 045 826 64 70 - Fax +39 045 826 64 69

mail:

info@tecnosicurezza.it

- web:

www.tecnosicurezza.it

Ask a Question ?

PDF User Manual

T8530\ EM2050/A\ EM3550/A\ EM3550/A/S\ DE20 series\ BR50 series\ ST40 series

Full Text Searchable PDF User Manual