Tecnolec TL115W-U Instruction Manual - User Manual

Download PDF User Manual

Full Text Searchable PDF User Manual

FP8QGHU&RXQWHU

Larder Fridge

MODEL:

7/:

-U

TL115SL-U

INSTRUCTION MANUAL

Names of parts

○

1 Evaporator

○

Wire

Shel

ves

○

3 Crisper Cover

○

4 Crisper Box

○

5 Leveling Feet

○

6 Bottle Racks

○

7 Recessed Handle

○

8 Door Switch

○

9 Thermostat and lamp assembly

THANK YOU FOR PURCHASING THIS

TECNOLEC

PRODUCT

This booklet contains the information you will require to install and operate your new
appliance.

It is important and worthwhile spending time to fully read this booklet so you will
understand how to operate the appliance safely and efficiently.

Please keep this booklet in a safe place so that you can refer to it when required.

ELECTRICAL CONNECTION (UK ONLY)

For your safety please read the following information.

Warning: This appliance must be earthed.

The appliance must be connected to a 240 volts 50 cycle AC supply by means of a three
pin socket, suitably earthed and should be protected by a 13 amp fuse in the plug.
The appliance is supplied with a standard 13 amp 3-pin plug fitted with a 13-amp fuse.
Should the fuse require replacement, it must be replaced with a fuse rated at 13 amp and
approved to BS1362.
If the mains plug is unsuitable for the socket outlet in your home or is removed for any
other reason, then the cut off plug should be disposed of safely, do not insert the cut off
plug into a mains outlet to prevent the hazard of electric shock. Remove the fuse before
disposal.
There is a danger of electric shock if the cut off plug is inserted into any 13-amp socket
outlet.

How to wire a 13 amp plug:

Important

The wires in the mains lead on this appliance are colored in accordance with the following
code:
Green and Yellow - Earth
Blue – Neutral
Brown – Live

As the colours may not correspond with the markings identifying the terminals in your plug
proceed as follows.
The green and yellow wire must be connected to the terminal in the plug which is marked

with the letter E or with the earth symbol

or colored green and yellow.

The blue wire must be connected to the terminal marked N.
The brown wire must be connected to the terminal marked L.
You must make sure the mains cord is firmly secured under the cord clamp.

REFRIGERATOR SAFETY INFORMATION

Check that the voltage marked on the rating plate matches that of your local supply.

Failure to use the correct voltage will render the guarantee VOID and may cause damage to
the appliance.

The manufacturer accepts NO responsibility for using any other voltage than that marked on
the rating plate.

This appliance is intended for domestic use only; any other use may invalidate the warranty
and might be dangerous.

This appliance is intended for indoor use only, do not use or store outdoors. This appliance
shall not be exposed to rain.

The mains plug shall be the main disconnect device and shall remain operable at all times.
A short power-supply cord is provided to reduce the risk of a tripping hazard.

To disconnect from the mains completely, turn the appliance OFF, then remove the plug from
wall outlet.

Do not immerse the appliance, its lead or plug in water or any other liquid.

Remove all food and unplug from the supply when not in use and before cleaning the
appliance.

If the mains lead becomes damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified person with a specially prepared lead of the same type and rating
to avoid a hazard.

Do not operate the appliance with a damaged cord or plug or after the appliance malfunctions
or has been damaged in any way.

Do not let cord hang over edge of the surface, or touch hot surfaces.

Do not place the appliance on or near hot surfaces, or in direct sunlight.

Children must be supervised to make sure they do not swing on the door.

Accessible surfaces may get hot when in use, use handles and knobs at all times.

Always attach a plug to the appliance, and then plug it into the wall outlet and switch on.

If you are discarding an old appliance with a lock or catch fitted to the door, ensure that it is
left in a disabled condition to avoid the entrapment of young children when playing.

As old refrigeration appliances may contain CFC’s which will damage the ozone layer, when
disposing of any refrigeration appliance please contact your local waste disposal department
for advice on the correct method of disposal.

This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been

given supervision or instruction concerning use of the appliance by a person responsible for
their safety.

Children should be supervised to ensure that they do not play on or near the appliance.

This appliance is for refrigerating food only.

REFRIGERANT

The refrigerating gas contained in the circuit of this appliance is Isobut

ne (R600a); it causes

a low level of pollution but is inflammable.

CAUTION

Extreme caution must be used when moving the appliance.

WARNINGS:
Do not damage the refrigerant circuit.

Do not use electrical appliances inside the food storage compartments of the
appliance, unless they are of the type recommended by the manufacturer.

If the appliance is installed in a carpeted area, do not let the carpet block the
ventilation holes in the base of the unit, adjust the levelling feet after a few hours to
compensate for carpet movement.

Keep ventilation openings, in the appliance enclosure or the built in structure clear of
obstructions.

Installation

Position the appliance and allow to stand for two to three hours before it is turned on
for the first time to allow the system to settle. Do not position next to any heat source
e.g. cooker, boiler or in direct sunlight etc.

A clearance of 10 cm must be left between the sides of the appliance and any adjacent
cabinets or walls to allow for adequate air circulation. The appliance is not designed for
recessed installation (“building in”).

Install on a good firm level surface, and any unevenness of the floor should be
corrected prior to installation, slight unevenness can be overcome by adjusting the
front feet.

Do not keep your appliance in a room where the temperature is likely to fall below 16
degrees C (61 degrees F) at night and/or especially in winter, as it is designed to
operate in ambient temperatures between +16 and +32 degrees C (61 and 90 degrees
F). At lower temperatures the appliance may not operate, resulting in a reduction in
the storage life of the food.
Do not place the appliance near cookers or radiators or in direct sunlight, as this will cause
extra strain on the appliance’s functions.
If installed next to a source of heat such as a fridge, maintain the following minimum
clearances.
Choose a well-ventilated location with no less than 10cm clearance around the refrigerator.
Place the refrigerator in a location with a firm base in order to prevent vibration and excessive
noise.
Level the refrigerator by adjusting the two front feet.

Instructions for use

Remove all packing materials and check for damage, if the appliance is damaged, do
not use the appliance, contact the store where you purchased the appliance. Wash
the interior of the appliance using lukewarm water containing a little bicarbonate of
soda in the proportion of 1 teaspoon to 1.2 litres (2 pints) of water. Do not use
detergents or soaps as they may taint the food. After cleaning, dry all parts
thoroughly.

Temperature Control

The refrigerator is designed to maintain an internal storage temperature in the
refrigerator compartment between 0

℃

to +

℃

To enable adjustment of the temperature in the appliance it is fitted with an
adjustable thermostat located in the fridge compartment, which can be adjusted from
setting 1(warmest) to 7 (coldest). For normal working temperature it is recommended
to adjust the thermostat control to the position

.0, after a few hours readjust the

thermostat to the desired temperature. There is also an off position “0”. Which
turns the refrigerator off. Note this dose not disconnect the appliance from the mains
supply. To do this you must remove the mains plug from the wall outlet.

To obtain a lower internal temperature turn the thermostat temperature control
clockwise to a higher number. To obtain a higher internal temperature turn the
thermostat control anticlockwise to a lower number. The internal temperature and
temperature control setting is dependent on a number of factors:

1. Varying ambient temperatures.
2. The number of times the appliance door is opened and how long the door remain

open.

3. The amount and temperature of the food and drink introduced into the appliance.
4. The weather conditions and time of year e.g. summer/winter.
5. The positioning of the appliance and an adequate air circulation to the sides and

back of the cabinet.

Never place hot or warm foods into the refrigerator or leave the doors open for longer
than necessary as this will raise the temperature and cause excessive amounts of
moisture thus increasing the amount of ice in the refrigerator compartment.

The Internal Light

The internal light will automatically switch ON and OFF whenever the refrigerator
door is opened or closed. To change the light bulb, see the section on changing the
light bulb.

Storage of fresh food in the refrigerator

Food should always be covered tightly with foil, plastic film, placed in bags or stored

in airtight containers. This will prevent food from dehydrating and prevent the strong

smell of some foods transferring to milder ones.

To store raw meat wrap in polythene bags or airtight containers and place on the

lowest shelf.

Do not allow raw meat to come into contact with cooked foods. For safety, only store

raw meat for two or three days. Fruit and vegetables should be thoroughly cleaned

and placed in the vegetable/ salad bin.

Milk and other liquids should be sealed with lids and placed in the bottle shelf on the

door.

Refrigerator defrost process

The refrigerator defrosting process is carried out automatically every time the

compressor stops.The defrost water drains from the cabinet into a tray placed on the

top of compressor to the rear of the unit where it evaporates.

Cleaning and maintenance

Before any cleaning or maintenance is carried out you must disconnect the appliance

from the mains supply by removing the plug, never remove the plug by pulling on the

mains cord. Remove the plug by pulling on the plug itself. It is recommended that when

clearning the appliance, both the inside and outside, can be cleaned using warm water

and a little bicarbonate of soda. Use 1 teaspoon to 1.2 litres of water.If the appliance is

to be used for a long period of time then it is recommended to remove all the food stuff,

clean the inside of the appliance and leave the door open to allow the air to circulate

thus avoiding unpleasant odours.

Changing the light bulb
Note.

Light bulbs are not covered by the warranty.

Turn the thermostat to the off position (0)

and disconnect from the mains. Push the clip at the base of light to the rear to release the

lamp cover. The Lamp is located in the back of the thermostat housing, unscrew the lamp

in an anti-clockwise direction until the lamp comes out of the lamp fitting.Screw a new

10 Watt (E14 Base) lamp into the lamp fitting in a clockwise direction until tight. Replace

the lamp cover back into position and click back into place. Set the thermostat to your

preferred setting and close the door.

If the appliance is not operating correctly:

Please check the following points.

Is there a power failure? (Check by turning on a house light)

Has the fuse blown or has the circuit breaker tripped?

Has the door been closed correctly?

Check the thermostat has been set correctly.

Check the mains plug seated in the wall socket correctly and the socket switch is on.

Reversing the door

This refrigerator has been built with the door hinges on the right. If you wish to

change the opening direction, follow the instructions below:

1. Remove the upper hinge cover (6) first.

2. Remove the two screws (1) that hold the upper hinge (5) (right side) to the fridge

body. Remove the upper hinge (5).

3. Lift the door and place it on a padded surface to prevent scratching it.

4. Reverse the hole cover plate (7) from the left side to the right.

5. Remove the foot (3) and the two screws (8) that hold the lower hinge (2) and

remove the lower hinge (2).

6. Remove the left front foot (4) and transfer it to the right side.

7. Before fitting the lower hinge (2), swap over the hinge pin (9) to the other side of

the lower hinge (2). Then install the lower hinge (2) onto the left side of the lower

frame with two screws (8), then re-fit the foot(3).

8. Position the door in place making sure the door seats onto the lower hinge (2).

9. Align the door in the closed position secure the upper hinge (5) in the top fame on

left side with two screws (1). Remember, do not tighten the two screws (1) until

the top of the door is leveled with the top of the fridge.

10. Install the upper hinge cover (6) on the upper hinge.

FIGURE 1 - REPRESENTATIVE POSITION OF COMPONENTS PRIOR TO

DOOR REVERSAL.

FIGURE 2 - R

EPR

ESENTATIVE POSITION OF COMPONENTS AFTER

DOOR REVERSAL.

Wipe the inner and outer surface of the refrigerator and its accessories with a wet cloth.

If they are too dirty, scrub them with a mild detergent, and then clean them with

water and dry them with clean cloth. After this, a small quantity of glass wax is

recommended to polish the refrigerator surface with a flannelette.

Once a month clean the condenser circuit and compressor with a stiff brush to remove

dust and deposits that may adversely affect the performance of the appliance.

1. When the refrigerator does not work

Check if there is a power failure.

Check if the power plug is plugged into the power outlet.

Check that the fuse has not blown.

2. When the refrigerator is cooling excessively

The temperature control dial may be set too high.

If you place foodstuffs containing a lot of moisture directly under the cool air

outlets, they will freeze easily. This does not indicate a malfunction.

3. When the refrigerator is not cooling sufficiently

The food may be packed too tightly together which will block the flow of cool air.

You may have put something hot or a lot of foodstuffs into the refrigerator.

The door may not have been closed properly.

The door gaskets may be damaged.

The refrigerator may not be ventilated.

There may be insufficient clearance between the refrigerator and the surfaces

immediately both sides and above.

The temperature control dial may not be set properly.

4. When condensation form on the outside of the refrigerator.

Condensation may form on the outside when the humidity is high such as during a

wet season. This is the same result as the condensation formed when chilled water

is poured into a glass. If does not, therefore, indicate a failure, wipe dry with a dry

cloth.

5. When you hear a sound like water flowing.

A sound like water flowing is the refrigerant flowing. It does not indicate a

malfunction.

6. When the cabinet’s side/rear panel heats up

The side panel of the cabinet will heat up when the door is opened or closed

frequently, when starting the unit and when the unit operates in summer with high

ambient outside temperature, in such case, do not touch the panel, it results from

the dissipation of the heat from inside the cabinet, and it does not mean the

something is wrong with the refrigerator.

Maintenance

Troubleshooting

Before calling for service

Please check the following points:

1. The refrigerator is not working

Check the plug is inserted correctly into the wall socket

Check there is power to the wall socket by plugging in another appliance, if the other

appliance works, check the fuse in the appliance plug.

2. The refrigerator is noisy when running

Check the appliance is level and is not in contact with another appliance or kitchen

furniture.

3. The refrigerator does not cool sufficiently.

If the door has been opened too often, or it has been left open for a while it will take

time for the appliance to reach its set temperature.

Check the air flow around the refrigerator has not been reduced due to insufficient

clearance.

NOTE: The following characteristics should not be looked upon as a problem.
A gentle trickling sound caused by coolant flowing through the pipe.
Compressor operating at high temperature.

Prolonged off periods

If the refrigerator is not in use for a long period of time, proceed as follows:

Disconnect the refrigerator from the main supply by removing the plug from the

socket.

Clean and dry the inside as instructed under the heading of cleaning the appliance.

Leave the door open to prevent any unpleasant smells from building up while the

appliance is not in use.

If there is a power failure for a short time keep the door closed check the contents of

the refrigerator every so often.

Tips for Saving Energy

1.Make sure that the appliance is not near a heat source.
2.Place the appliance in a dry and well-ventilated and no direct sunlight place.
3.It is always a good practice to pack, wrap and cover the food before storing.
4.Food and beverages shall cool to room temperature before storing.
5.Keep space between the food when load food into the appliance to allow
circulation of air.
6.Long time or frequent door openings can cause internal temperature rise so
the door shall be closed as soon as possible after use.
7.Keep the appliance door gasket sealing well and the appliance ventilation
openings(if any) free.
8.Do not leave frozen food at room temperature to thaw. You could defrost the
food by putting it in the fridge to thaw slowly. Make sure you avoid defrosting
food or food juices drip onto other food.
9. The pre-set combination of drawers, baskets and shelves has already been
set in the most efficient use of this product.

Do's and Don'ts

Do-

Clean your appliance regularly.

Do-

Take off any unusable leaves on vegetables and wipe off any soil.

Do-

Keep raw meat and poultry below cooked food and dairy products.

Do-

Leave lettuce, cabbage, parsley and cauliflower on the stem.

Do-

Wrap cheese firstly in greaseproof paper and then in a polythene bag, excluding As

much air as possible. For best results, take out of the fridge compartment an hour before
eating.

Do-

Wrap raw meat and poultry loosely in polythene or aluminium foil. This prevents

drying.

Do-

Wrap fish and offal in polythene bags.

Do-

Wrap food with a strong odour or which may dry out, in polythene bags, or aluminium

foil or place in airtight container.

Do-

Wrap bread well to keep it fresh.

Do-

Chill white wines, beer, larger and mineral water before serving.

Do-

Keep food for as short a time as possible and adhere to "Best before" and "Use by"

etc. dates.

Do-

Store commercially prepared food in accordance with the instructions given on the

packets.

Do-

Always choose high quality fresh food and be sure it is thoroughly clean before

Storing it.

Do-

Wrap all food in aluminium foil or food quality polythene bags and make sure any

air is excluded.

Do-

Keep ventilation openings, in the appliance enclosure clear of obstruction.

Don't-

Cover the shelves with any protective materials which may obstruct air circulation.

Don't-

Store poisonous or any dangerous substances in your fridge. It has been designed

for the storage of edible foodstuffs only.

Don't-

Consume food which has been refrigerated for an excessive length of time.

Don't-

Store cooked and fresh food together in the same container. They should be

packaged and stored separately.

Don't-

Let defrosting food or food juices drip onto already stored food.

Don't-

leave the door open for long periods, as this will make the appliance more costly

to run and cause excessive ice formation.

Don't-

Use sharp edged objects such as knives or forks to remove the ice.

Don't-

Use hairdryers, or electrical appliances for defrosting only use item recommended

by the manufacturer.

Don't-

put hot food into the appliance. Let it cool down first.

Don't-

Try to keep frozen food which has thawed; it should be eaten within 24 hours or

cooked and refrozen.

Don't-

Damage the refrigerant circuit at any time.

NOTE:

DO NOT POSITION YOUR APPLIANCE IN AN EXCESSIVELY COLD OR HUMID AREA

SUCH AS A GARAGE/CELLAR OR OUTBUILDINGS ETC.

Technical data

Brand Tecnolec

Appliance type

Larder Fridge

Star rating

Total gross volume (l.)

Total storage volume (l.)

115

Freezer storage volume (l.) 0L

Refrigerator st orage volume

115

Maximum bulb power (W) 10W

Climate Class +Ambient Range N (+16C to +32C)

Energy class (1) A

Power consumption (kWh/year) (2) 1

Supply voltage (V/Hz)

220-240V

~ ,

50Hz

Noise [dB(A)re 1 pW]

<40

Refrigerating agent R600a/21g

Outside dimensions (W x D x H)

500

0*840mm

Insulation Blowing Gas

Cyclopentane

(1) Energy class: A…..G (A= economical…G= less economical)

(2) The real power consumption depends on using conditions and

appliance location.

0mm

500

1010

0mm

Ask a Question ?