Full Text Searchable PDF User Manual
Installation
1. Insert the round base to the back pole (as indicated)
of your LED weather station, turn the base to the right
to secure it in position.
2. Plug the AC/DC adaptor into any 230V European
AC household outlet. Plug the DC jack into the lower
back of the clock. The top front of the clock will show
and the indoor-outdoor temperatures and
weather forecast display will appear. Your LED weather
station is ready to work for you.
Battery Back Up
1. Slide the battery door at the back case, insert 3 x AAA batteries with correct + and - polarity signs inside
the battery compartment. Replace the battery cover.
2. When AC power is off, the batteries will power t he clock to keep track of the time and alarm time.
3. When only the back-up batteries is used, the LED panel is off.
Power Up Reception and Signal Strength Display
1. After plug in AC power, the clock starts to receive DCF signal.
Icon blinks. Display shows
2.
When strong DCF signal is detected, display shows with 3 bars
When weak or no DCF signal is detected, display shows with 1 bar
or . You will need to place the clock to another area for better
reception, or unplug the AC/DC jack to start over reception again. During
reception, the signal strength may move from 1 bar to 2 bars to 3 bars. This
is normal since the clock is detecting DCF signal and other signals in the
air at the same time.
3. If the clock does not catch DCF time signal for 7 minutes, it will go back
to normal time display
4. During reception, press TIME button once will go to normal time
display.
Press HR again will return to reception mode and signal strength indication.
Successful reception or failed reception
Icon becomes static on (stop blinking) when reception is successful Icon
disappears when reception is failed
Weak or no RC signal Is
detected
Successful Reception
Automatic Reception and Manual Reception
Automatic reception : this clock starts reception automatically everyday at 1:00am. If auto recpetion fails at
1:00 am, it will start again at 2:00 am. If fails at 2:00 am, it will start again at 3:00 am.
If auto recpetion fails at 3:00 am still fails, it will start reception every 3 hours until it succeeds to catch correct
DCF time.
Manual reception : press HR button once anytime to start manual reception of DCF time signal. The LED time
display will go to radio controlled reception mode
To Set Time and Alarm Time
After power up, if press
TIME
button once, time digits go to 0:00 am (default
start-up time). The clock continues to receive DCF signal. The icon is still
blinking.
Press HR button once will go back to radio controlled reception mode (as above)
TO SET TIME
Press and hold
TIME
button and at the same time press HR button once at a time
to set hour.
Press and hold
TIME
button and at the same time press
MIN
button once at a time
to set minute.
SET ALARM 2
TO SET ALARM 1 TIME
1. Slide the Alarm Switch to
ALM
1.
2. Press and hold
ALM
button and at the same time press HR button once at a time to set hour.
3. Press and hold
ALM
button and at the same time press
MIN
button once at a time to set minute.
TO SET ALARM 2 TIME
1. Slide the Alarm Switch to
ALM
2.
2. Press and hold
ALM
button and at the same time press HR button once at a time to set hour.
3. Press and hold
ALM
button and at the same time press
MIN
button once at a time to set minute.
TO TURN ON/OFF ALARM 1 or/and ALARM 2
1. To turn on
Alarm 1
only, slide the alarm switch to
ALM
1, ALM 1 LED lights up on upper left of the hour
digits.
2. To turn on
Alarm 2
only, slide the alarm switch to
ALM
2, ALM 2 LED lights up on lower left of the hour
digits.
3. To turn on both
Alarm 1
and
2,
slide the alarm switch to
ALM
1 + 2, both ALM 1 and ALM 2 LED light up.
4. To in-activate both
Alarm 1
and
2
permanently, slide to
ALM OFF.
Both ALM 1 and ALM 2 LED turn off.
TO USE THE SNOOZE ALARM
When time reaches the set
ALARM 1
and/or
ALARM 2
time, the clock will beep with the
ALM
1 and/or
ALM
2
LED blinking.
Press the
SNOOZE
button once, the alarm sound will stop and
ALM
1 or
ALM
2 LED keep blinking. Alarm will
sound againin 5 minutes.
TO STOP THE ALARM
When time reaches the set
ALARM 1
and/or
ALARM 2
time, the clock will beep with the
ALM
1 and/or
ALM
2
LED blinking.
Press and hold the
SNOOZE
button for 2 seconds, the alarm sound will stop and ALM 1 or ALM 2 LED
becomes static. Alarm 1 and/or Alarm 2 will sound again same time next day.
TO TURN OFF ALARM 1 AND/OR ALARM 2 PERMANENTLY
Slide the alarm switch to
ALM OFF.
Alarm sound will stop and both
ALM
1 and
ALM
2 LED's turn off.
TO SET SNOOZE DURATION (from 5 to 60 minutes)
Press and hold
SNOOZE
and time display will show "05" (default snooze duration) and then press
MINUTE
button to set your desired snooze duration.
TO READ MAXIMUM-MINUMUM INDOOR-OUTDOOR TEMPERATURES
Simply press the
button to view the maximum indoor and outdoor temperatures. Press
MAXCLEAR
to reset the
Max readings. The readout will now appear as — and will start to record the maximums again.
Then press the button to view the minimum indoor and
outdoor temperatures. Press MAXMINCLEAR to reset the
Min readings. The readout will now appear as — and will start to record the minimums again.
IF YOU LOSE THE OUTDOOR TEMPERATURE
When the outdoor temperature digits show '—--", the wireless transmission is either interrupted or lost. Press the
CLEAR
button at the back of your LED weather station, then press
RESET
button at the back of the outdoor
transmitter. If you continue to lose the outdoor temperature display, try placing the transmitter in a different
location until you have smooth transmission of temperature data.
USING THE WEATHER FORECASTER AND BAROMETER
Your LED weather station has a built-in barometer which measures the barometric pressure. After power up,
the display shows Sunny & Cloudy icons. Your LED weather station takes around 24 hours to gather data of
barometric pressure changes and predicts next 1 2 - 2 4 hours weather conditions.
There are four types of weather display of the predicted weather condition :
TROUBLE SHOOTING
Press the
RESET
button on the back of the base thermometer and then press
RESET
button located on the
back of the outdoor transmitter. Once you do this, your clock will be reset to default setting and needs to be
up-dated by DCF time signal again.
TO USE THE HI-LO DIMMER SWITCH
Simply slide the
LO-HI DIMMER
switch at the back of the clock to adjust the LED brightness to a comfortable
level to you in the dark.
CARE OF YOUR CLOCK
1. Do not expose your clock to extreme temperatures, water or direct sunlight.
2. Avoid contact with any corrosive materials
3. Do not subject the clock to excessive force, dust or humidity
4. Do not open the inner back case or tamper with any components of this clock
5. Do not plug in any other AC/DC adaptor with incorrect specifications or voltage
6. Do not place your clock in range of
strong interferences. (TV, Microwave…)
SUNNY
SUNNY & CLOUDY
CLOUDY
RAINY
Your weather forecaster also has weather tendency indicator, when the air pressure is going up (the weather will
improve) the UP arrow will appear, when the air pressure is going down (the weather will go worse) the DOWN
arrow will appear.
Remarks : Moving your weather station around your house or your building will affect its accuracy because the
sudden change of temperature or height/altitude will affect the accuracy of your weather station. It
will take 24 hours to get stable again to predict next 12-24 hours weather condition.
Your weather station predicts next 12 - 24 hours weather conditions. It may not match with the current weather
condition outside.
Instruction Manual
WS 6830
RC tower Icon blinking
Strong DCF signal is detected,
Minute digits may start counting
01,02,03...60,00,01,02.... trying
to match with the correct seconds
DfJJY signal
Failed Reception
SET ALARM 1