TechnoKom AutoGRAPH-Mobile User Manual - User Manual

Download PDF User Manual

Full Text Searchable PDF User Manual

DOCUMENT

VERSION

2.5

MOBILE

VEHICLE AND PERSONAL TRACKING SYSTEM

USER MANUAL

AutoGRAPH-Mobile • USER MANUAL

Contents

Introduction

............................................................................................................................................................

Version history

......................................................................................................................................................

Related documentation

....................................................................................................................................

Software Copyright Notice

..............................................................................................................................

Safe Operation and Exposure to Electromagnetic Fields

..................................................................

Basic Information

.................................................................................................................................................

Scope of Supply

...................................................................................................................................................

Technical Specifications

...................................................................................................................................

Components of AutoGRAPH-Mobile

.........................................................................................................

Getting Started

..................................................................................................................................................

Installation of SIM-cards

............................................................................................................................

Inserting the battery

....................................................................................................................................

Charging the battery

..................................................................................................................................

Switching on / off

.........................................................................................................................................

AutoGRAPH-Mobile Functions

...................................................................................................................

Coordinate acquisition

...............................................................................................................................

Data transmission

........................................................................................................................................

SMS

...................................................................................................................................................................

Alert signal

......................................................................................................................................................

AutoGRAPH-Mobile Operation Modes

....................................................................................................

Tracker Indicators

.............................................................................................................................................

Indication of GNSS receiver operation

...............................................................................................

Indication of GSM modem operation

...................................................................................................

Indication of the battery charging

..........................................................................................................

Drivers Installation

...........................................................................................................................................

Connection to PC

.............................................................................................................................................

Care & Maintenance

.......................................................................................................................................

AutoGRAPH-Mobile Events

.........................................................................................................................

AutoGRAPH-Mobile • USER MANUAL

Introduction

This User Manual applies to the AutoGRAPH-Mobile vehicle and personal tracking device

(hereafter - tracker) produced by TechnoKom Ltd. It contains installation and connection

procedures of the AutoGRAPH-Mobile, as well as its function and control.

This Manual constitutes the Operating Rules to be observed to ensure successful operation of

the controller and its compliance with TU 6811-005-12606363-2016 and warranty provisions.

For proper operation of the AutoGRAPH-Mobile controller, a user should be aware of operating

principles of the personal tracking system as a whole, as well as understand functions of its

individual components. Therefore, it is recommended to study the fundamentals of operation

of GPS navigation, GSM communication, peculiarities of short message service (SMS),

GPRS and the Internet before starting.

Some functions of AutoGRAPH-Mobile controllers depend on capacities and configuration of the
existing mobile network operator (MNO).
Furthermore, some functions may be disabled by the operator, or their operating range may be limited
due to the settings of the network. To check availability of a certain function, contact your mobile
network operator.

IMPORTANT

All information on functions, functional capabilities and other specifications related to AutoGRAPH-
Mobile personal tracking controllers, as well as all information contained in this User Manual is based
on current data (at time of writing) and is deemed to be valid as of the date of publication.
Technokom reserves the right to modify the information or specifications without prior notice or
commitment.

IMPORTANT

Version history

This table provides a summary of the document revision.

Version Description

Date

2.4

Version for the AutoGRAPH-Mobile device with extended battery

capacity and SOS button.

03/2015

2.5

Added description of AutoGRAPH-Mobile events

Added description of AutoGRAPH-Mobile modes

10/2016

AutoGRAPH-Mobile • USER MANUAL

Software Copyright Notice

Products of TechnoKom referred to in this Manual may incorporate software stored in

semiconductor memory or other media, copyrights to which belong to TechnoKom or third

parties. Laws of the Russian Federation and other countries secure certain exclusive rights

of TechnoKom and third parties to the software, which is subjected to copyright, for example,

exclusive rights for distribution or reproduction.

Therefore, any alteration, reverse engineering, distribution or reproduction of any software

incorporated in TechnoKom products, is prohibited to the extent provided by law.

Furthermore, purchase of TechnoKom products does not imply direct, indirect or other

granting of any licenses related to copyrights, patents and patent applications of TechnoKom

or any third party, except for an ordinary, nonexclusive free license for use, which is granted

in virtue of law upon each sale of the product.

Communication protocol between AutoGRAPH-Mobile vehicle and personal tracking

controllers and a data server is considered to be confidential information and intellectual

property of TechnoKom.

The communication protocol between AutoGRAPH-Mobile vehicle and personal tracking

controllers and a communication data server shall be transferred by TechnoKom to integrators

and software manufacturers only upon signing the Confidentiality Undertaking.

Unauthorized distribution of protocol used for communication between AutoGRAPH-Mobile

vehicle and personal tracking controllers and communication data server is strictly prohibited.

Related documentation

Given below is a list of the documentation related to AutoGRAPH on-board controller.

•

MobileConf help file.

This document covers detailed instruction related to

AutoGRAPH-Mobile controller configuring using the MobileConf program. The help file is

supplied with MobileConf program.
•

Control SMS and server commands of AutoGRAPH-Mobile controller

. This

document contains description of the commands format intended to control and configure

AutoGRAPH-Mobile controller remotely via data server or by means of SMS.

AutoGRAPH-Mobile • USER MANUAL

This section contains important information

for effective and safe operation. Please

read the information below before using

AutoGRAPH-Mobile vehicle and personal

tracking controllers.

Performance Characteristics

AutoGRAPH-Mobile vehicle and personal

tracking controllers operate using a GSM/

GPRS module and function as a low power

receiver and transmitter. When the tracker is

ON, it receives and transmits electromagnetic

energy in the radiofrequency range.

Operating band of the tracker ranges from

900 MHz to 1,990 MHz; the tracker uses

digital modulation techniques.

When the tracker is in operation, a call

service system controls the strength of sent-

out RF signal.

Russian National Standards

AutoGRAPH-Mobile on-board vehicle

tracking controllers are designed on the

basis of TU 6811-005-12606363-2016 and

comply with the following standards:
• GOST R MEK 60950-2009. Information

Technology Equipment. Safety.

• GOST R 51318.22-2006. Electromagnetic

Compatibility of Technical Equipment.

Information Technology Equipment. Man-

Made Radio Disturbance. Limits and

Methods of Measurement.

• GOST R 51318.24-99. Electromagnetic

Compatibility of Technical Equipment.

Immunity of Information Technology

Equipment. Requirements and Test

Methods.

•

GOST R Certificate of Conformity: GOST

R № ROSS RU.МN11.Н09267.

•

TR CU Certificate of Conformity: TS RU

D-RU.АL15.V.00712.

Exposure to Electromagnetic

Fields

The design of the AutoGRAPH-Mobile

vehicle and personal tracking controller

complies with the following national and

international standards, which specify the

safe levels of exposure to radiofrequency

electromagnetic fields:

• Ministry of Information Technologies

and Communications of the Russian

Federation. Regulations for application of

user equipment (user radio stations) within

GSM-900/1800 mobile telecommunication

networks, approved under Order of

Ministry of Information Technologies

and Communications of the Russian

Federation No. 114 dated September 20,

2005 (registered with Ministry of Justice of

the Russian Federation on Sep. 28, 2005

under No. 7045).

• United States Federal Communications

Commission, Code of Federal Regulations;

47 CFR part 2 sub-part J.

• American National Standards Institute

(ANSI) / Institute of Electrical and Electronic

Engineers (IEEE) C95.

• Institute of Electrical and Electronic

Engineers (IEEE) C95 1-1999 Edition.

• National Council on Radiation Protection

and Measurements (NCRP) of the United

States, Report 86, 1986.

• International Commission on Non-Ionizing

Radiation Protection (ICNIRP) 1998.

• National Radiological Protection Board of

the United Kingdom 1995.

• Ministry of Health (Canada) Safety

Code 6. Limits of Human Exposure to

Radiofrequency Electromagnetic Fields in

the Frequency Range from 3 kHz to 300

GHz, 1999.

Safe Operation and Exposure to

Electromagnetic Fields

AutoGRAPH-Mobile • USER MANUAL

• Australian Communications Authority

Radiocommunications (Electromagnetic

Radiation - Human Exposure) Standard

1999 (applicable to wireless phones only).

In order to ensure the best communication

quality and compliance with the safety

standards stipulated by the abovementioned

documents, the equipment operating rules

must be followed.

Electromagnetic Interference and

Compatibility

Almost any electronic device is subjected

to electromagnetic interference unless it is

adequately shielded, has proper construction

or is compatible with devices operating in

another frequency band.

Prohibition on Use of Mobile

Communication Devices

If you come across a signage or a notice, which

prohibits the use of mobile communication

devices, turn off your tracker. This is required

to avoid electromagnetic interference with

equipment sensitive to electromagnetic

fields often used in hospitals, health care

institutions or petrol stations.

Medical Devices

Cardiac Pacemakers

Medical Device Manufacturers Association

advises to use mobile communication devices

at distances greater than 15 cm from cardiac

pacemaker so as to prevent the failure of

the latter. These recommendations conform

to the studies carried out by independent

medical laboratories and Research Centre

for Wireless Technologies.

Hearing Devices

Sometimes, use of mobile communication

devices may cause troubles for wearers of

certain hearing devices. In this case, consult

the manufacturer of your hearing device to

select another model.

Other Medical Devices

For other personal medical devices, contact

your physician or device manufacturer to

find out whether your device is adequately

shielded from electromagnetic interference

generated by mobile communication devices.

General Information on Safe Use

Explosion Hazard Zones

SWITCH OFF the tracker when entering the

explosion hazard zone. Explosion hazard

zones include: fuel stations, box girder decks

on sea vessels, facilities or plants for handling

and storage of fuels or chemicals, areas with

chemicals or solid particles such as grains,

dust or metal powder in atmosphere; and any

other locations where it is usually required to

shut off a vehicle’s engine. Explosion hazard

areas are often (yet not always) expressly

marked.

Blasting Areas

In order to avoid interference with blasting

operations, SWITCH OFF the device in

blasting areas or in any locations marked

with “Two-way radio-communication is

prohibited” signage. Observe the signage

instructions and rules.

AutoGRAPH-Mobile • USER MANUAL

Basic Information

The «AutoGRAPH-Mobile» (GLONASS/GPS) personal tracking controller is a portable

autonomous electronic unit which tracks all movements of assets by recording the time and

the route in the form of geographic coordinates received from the satellites of global navigation

system GPS (NAVSTAR) or GLONASS.

In addition to coordinates, the tracker records a number of other parameters: speed, direction

of movement, event counters, state of alert button, etc.

Collected data is transferred by a GSM 900/1800 mobile network operator by means of

General Packet Radio Service (GPRS) to the dedicated server where it becomes available

via the Internet for further analysis and processing by the AutoGRAPH Dispatch Software.

Scope of Supply

№

Description

Qty

AutoGRAPH-Mobile Personal Tracker (GLONASS+GPS)

1 pc.

Power Adapter+USB Cable

1 pc.

Warranty Certificate

1 pc.

AutoGRAPH-Mobile • USER MANUAL

Technical Specifications

Description

AutoGRAPH-Mobile

GPS/GLONASS Receiver

Receiver type

uBlox MAX-M8Q

Supported GNSS

GPS + GLONASS /

GALILEO / Beidou

Channels

Autonomous A-GNSS

Yes

Differential GPS (DGPS)

SBAS (WAAS, EGNOS, MSAS,

GAGAN, QZSS), RTCM

Position accuracy when using GPS/GLONASS GNSS

• Horizontal (typ.), m

• Velocity (typ.), m/s

2.00 (50%)

0.05 (50%)

Time to first fix

, s

Type of GPS/GLONASS antenna

Internal

GSM modem

Communication

GSM / GPRS / SMS

SIM holders

Position accuracy when using LBS

• in city, m

• in the countryside, km

200…1000

1…30

Type of GSM antenna

Internal

General

Connection to PC

USB 2.0

Internal FLASH memory, records

> 270.000

Alert button

Yes

Voice message service

Yes

Built-in accelerometer / motion sensor

Yes

Sleep mode when idling

Yes

Type of rechargeable battery

Li-Ion

Rated battery voltage, V

3.7

Battery capacity, mAh

1800

Charging time, min

approx. 160

External power supply voltage / Charging voltage, V

Operating temperature, °С

-20…+85

AutoGRAPH-Mobile • USER MANUAL

Description

AutoGRAPH-Mobile

Charging temperature, °С

0…+45

Dimensions, mm

92 х 58 х 22

Weight (with battery), g

With nominal signals level -130 dBm.

A wide specified range is supplied as the position accuracy when using LBS depends on base stations location around asset.

AutoGRAPH-Mobile • USER MANUAL

Components of AutoGRAPH-Mobile

1.  GSM LED (orange).
2.  GPS / GLONASS antenna placement.
3.  NAVIGATION/CHARGING LED (bi-colour).
4.  SOS button.

5.  Fastening screw (x4).
6.  POWER button (hidden).
7.  Manufacturer’s label.
8.  Mini USB connector.

AutoGRAPH-Mobile • USER MANUAL

Getting Started

Before turning on the tracker, it is recommended to insert the SIM cards and charge the

battery.

Installation of SIM-cards

The AutoGRAPH-Mobile is equipped with a dual SIM holder.

Do a test of a new SIM card in a cell phone before you install it into the controller. This ensures that GPRS
/ SMS / USSD services are enabled and operate properly, the PIN code matches the code preset in the
controller (in order to prevent locking), and the personal account associated with the SIM card has the
sufficient balance for successful operation of the services.

IMPORTANT

The SIM card installed in the lower retaining slot of the SIM holder is the main card. When

switched on, the AutoGRAPH-Mobile will operate with this SIM card. The SIM card installed

in the upper retaining slot of the SIM holder is the backup card. The tracker will switch to the

backup SIM card, when the primary one is unavailable (disabled, damaged or not inserted).

For proper operation it is quite sufficient to insert main SIM card in AutoGRAPH-Mobile. But

the backup card provides the appropriate operation of the tracker even if the main SIM card is

damaged. Due to this the tracker will stay connected and be able to transfer data.

To install a SIM card:

• Unscrew the four fastening

screws and remove the back cover

of the tracker.
• Insert a SIM card into the lower

retaining slot of the holder with the

card’s contacts facing the PCB

(see fig.1). Be sure that the card’s

keying matches the key on the

PCB.
• If necessary, insert a second SIM

card in the upper retaining slot of

the holder with the card’s contacts

facing downwards (see fig.3).

Be sure that the card’s keying

matches the key on the PCB.
• When the SIM cards are inserted,

replace the back cover and tighten

the four fastening screws.

AutoGRAPH-Mobile • USER MANUAL

Inserting the battery

The AutoGRAPH-Mobile comes with a rechargeable Li-Ion battery. The trackers are supplied

with batteries of 1800 mAh capacity.

To insert the battery:

• Unscrew the four fastening screws and remove the back cover of the tracker.
• Remove the PCB from the case.
•

Connect the battery to the Power connector located on the rear of the PCB (see fig.1).

• Insert the PCB back into the case.
• If necessary, turn on the tracker following the steps described in the “Switching on / off”

section.
•

Replace the back cover and tighten the four fastening screws (see fig.2).

Before installation, check the battery for any damage. Do not use expired batteries. Use only the
battery supplied with the tracker.

IMPORTANT

To prevent incorrect connection, which can damage the tracker’s supply circuit with short-circuit
current, the battery’s connector (male) and the Power connector (female) on the PCB are keyed. Be
sure that the battery’s keying matches the key on the Power connector.

IMPORTANT

AutoGRAPH-Mobile • USER MANUAL

Charging the battery

Before turning on and starting use of the AutoGRAPH-Mobile, it is recommended to charge

the battery.

The AutoGRAPH-Mobile comes with the USB power adapter and a USB cable (USB AM

– USB miniB 5pin) for charging the battery from an electrical mains of 220 V or from a PC.

To charge using the USB power adapter:

Connect the small end of the USB cable to the USB-mini connector of the tracker.

Connect the other end of the USB cable to the power adapter.

Connect the power adapter to a power outlet. Charging will automatically start.

To charge using USB cable:

Connect the small end of the USB cable to the mini USB connector of the tracker.

Connect the other end of the USB cable to a PC. Be sure that the PC is turned on.

Charging will automatically start.

During the charging NAVIGATION / CHARGING LED simultaneously flashes green and red

once a second. When the battery is charged the LED does not flash.

Average charging time is 160 minutes.

When connecting an external power to the tracker (using power adapter or USB cable), the tracker will
automatically start its operation.

NOTE

Switching on / off

When connecting the external power supply (using USB cable) the tracker automatically

switches on. When connecting to the internal battery the tracker must be switched on by

pressing the POWER button to start operation. Before switching on, be sure that the battery

is charged.

The POWER button is hidden in the tracker’s case. To press it:

• Unscrew the four fastening screws, remove the back cover of

the tracker and directly press the button;

• OR insert any pointed object (e.g. small bent paperclip) into

the small hole above manufacture’s label on the back cover.

AutoGRAPH-Mobile • USER MANUAL

Switching on

Before switching on, insert SIM cards into the tracker and connect the battery.

To switch the tracker on:

•  Press the POWER button for a few seconds;
•  As soon as the POWER LED turns on, release the button.
•  The POWER LED is located above the POWER button.

When the back cover is removed it is easy to see the LED

flashing. If the back cover isn’t removed, the LED can be

seen through the hole intended for the access to the POWER

button.

• Now the tracker is ready to operate.

When switching the tracker off, the second press must be performed while the POWER LED is ON (during
about 3 seconds after the first press). Otherwise, the switch off procedure should be started again. It is
made in order to suspend an accidental switching off of the tracker.

IMPORTANT

For proper operation the tracker must connect to a GSM network and acquire the position.

For the first start, it can take up to 23 seconds to determine the coordinates. The tracker’s

operation is indicated with two LEDs. More detailed information on the indication is given in

the “Tracker’s Indication” section.

Switching off

To switch the tracker off:

• Press the POWER button for a few seconds;

• As soon as the POWER LED turns on, release the button and quickly press it again.

• The POWER LED is located above the POWER button. When the back cover is removed

it is easy to see the LED flashing. If the back cover isn’t removed, the LED can be seen

through the hole intended for intended for the access to the POWER button.

• After the second press the tracker turns off.

The AutoGRAPH-Mobile can be set up to turn on only when the external power supply is connected
(5V). This mode can be used when the tracker is installed in a vehicle and allows to preserve the battery
power.

NOTE

AutoGRAPH-Mobile • USER MANUAL

AutoGRAPH-Mobile Functions

Coordinate acquisition

In normal mode, the AutoGRAPH-Mobile

acquires coordinates of the asset after the

specified period and records the coordinates

into FLASH memory. When turning on the

tracker for the first time, it can take up to 26

seconds to acquire the position. The acqui-

sition time depends on how clear the view of

the sky is and for the best performance, it is

recommended to locate the tracker with the

GPS/GLONASS antenna facing the sky. It is

not recommended to cover the tracker with a

metallic object.

State of the GNSS receiver is indicated with

the NAVIGATION/CHARGING LED (see the

“Tracker’s Indication” section). Depending on

settings, the tracker can switch to Standby

mode, when the asset is in an idle state. As

soon as motion is detected, the tracker will

return to normal mode of operation.

Data transmission

Collected tracking data is transferred to a

preset server. The tracker must be covered by

GSM network and GPRS must be available

to transfer the data to the server. The state of

the GSM modem is indicated with the GSM

LED (see the “Tracker’s Indication” section).

When the GSM modem is OFF, the GSM LED

does not flash. If a SIM card is not inserted or

incorrect PIN is entered, the tracker switches

the GSM modem off and data transmission

is not available.

SMS

Incoming SMS

The AutoGRAPH-Mobile supports remote

configuration. To configure the tracker

remotely, you should send an SMS with a

control command to the tracker, ensuring

that the telephone number of the active SIM

card is used. Advanced customers can send

the settings via the data server.

Outgoing SMS

On request, the tracker sends the current

coordinates to the customer by SMS. The

coordinates are sent as a link to an online

mapping service. By default, the tracker sup-

ports Yandex Maps, Yandex Satellite, Goog-

le Maps, and Google Satellite services, but

the customer can specify any other format

of the coordinates using the AGMobileConf

Program.

Also the tracker can be set up to send a no-

tification by SMS, when it enters / exits the

geofenced area.

Alert signal

This option is designed for use in life

threatening or other emergency situations.

The AutoGRAPH-Mobile is equipped with

an SOS button and capable of sending an

alert SMS with the current coordinates of the

asset. In an emergency, press and hold the

alert button for at least 3 seconds.

The AutoGRAPH-Mobile can be customized

to perform the following actions, when the

alert button is pressed:

To send SMS with the current coordinates

The tracker can be set up to send an SMS

with asset’s coordinates to preset telephone

numbers. Up to 4 telephone numbers can be

stored in the tracker’s memory.
The tracker sends two alert SMS messages.

The first message is short and contains

time of alert activation and the current

coordinates, if they are available. The second

SMS contains the current coordinates and

the last valid coordinates of the asset. The

coordinates are sent as a link to an online

mapping service.

The first (short) SMS is designed to be sent

as one message to increase the reliability of

data delivery. The second SMS is longer than

the first one, therefore, it may be received as

AutoGRAPH-Mobile • USER MANUAL

multiple messages, which can cause data loss if one of the messages isn’t delivered to the

customer.
If coordinate acquisition is unavailable using the GNSS, the tracker will determine its

approximate GSM localization. As soon as the coordinates are available, the device will send

them to the customer.

To send data to a preset server

The tracker can be set up to transfer the collected data to a preset server before the next

period of data transfer. Note, that in the alert mode the tracker transfers the data from internal

memory in roaming even if the data transmission in roaming is disabled in the tracker’s

settings.

To make a voice call

The tracker can be set up to send a voice message to preset telephone numbers. The tracker

will call to all preset numbers in sequence until one of the recipients answers the call. When

answering the call, the recipient will hear a preset voice message.

The AutoGRAPH-Mobile remembers state of the SOS button even after the restart. If the tracker does
not perform all preset functions of the SOS button before turning off, it will complete tasks after turning
on.

NOTE

AutoGRAPH-Mobile • USER MANUAL

AutoGRAPH-Mobile Operation Modes

To save battery resources, AutoGRAPH-

Mobile can be configured to switch to Sleep

mode when an asset is not moving or external

power of AutoGRAPH-Mobile is turned off.

The events forcing the device to switch to

Sleep mode can be easily set up by remote

configuration commands or in the MobileConf

program.

When the device is in Sleep mode, main

functional modules of the device are turned

off. Consequently, data is not recorded and

not transferred.

Sleep mode when asset is not moving

The device can be set up to switch to

Sleep mode when the asset equipped with

AutoGRAPH-Mobile is not moving. The

device detects moving according data

from an internal accelerometer and if there

is no moving during specified interval,

AutoGRAPH-Mobile switches to Sleep mode.

As motion is started, the device switches to

normal mode of operation. Also Sleep mode

can be cancelled by pressing SOS button on

the device.

Sleep mode when external power supply is

switched off

The device can be set up to operate only

from external power supply. If this option is

enabled, external power turning off switches

the device to Sleep mode till the external

power is restored.

The switching to Sleep mode can take from 15

to 75 seconds (20 seconds as the average).

After that the external power switches off,

the device stays in normal mode powered

by the internal battery in order to transfer

collected data to server. After transferring the

data, AutoGRAPH-Mobile switches to Sleep

mode.
If it is not available to transfer data, Sleep

mode is delayed for 60 seconds. After that

AutoGRAPH-Mobile tries to send data one

more time and then switches to Sleep mode

even no data has been transferred.
AutoGRAPH-Mobile stays in Sleep mode

until external power is restored, SOS signal

is activated by long press of the button or

special key combination is applied.
If Sleep mode is cancelled by long press of

SOS button, AutoGRAPH-Mobile switches

to Sleep mode again after processing all

operations which are preset for SOS button.
If Sleep mode is cancelled by the special key

combination, AutoGRAPH-Mobile switches

to normal mode for 3 periods of data

transmission but not less than 5 seconds and

not longer than 20 minutes.

To cancel Sleep mode by key combination:

• press SOS button and hold it for at least 1

second (but not longer than 2 seconds);

• pause for at least 1 second (but not longer

than 2 seconds);

• shortly double press SOS button of the

device.

AutoGRAPH-Mobile • USER MANUAL

Tracker Indicators

The AutoGRAPH-Mobile has two LEDs intended to indicate the device operation.
Install SIM cards, connect the battery and turn on the tracker. The tracker will be ready to

operate after location acquisition and connecting to a GSM network.

Indication of GNSS receiver operation

Location data is not available

– NAVIGATION / CHARGING LED (bi-colour) flashes green

twice a second.

Searching for satellites

– NAVIGATION / CHARGING LED flashes green once every

second.

Location is acquired

– NAVIGATION / CHARGING LED flashes green once every three

seconds.

Indication of GSM modem operation

Searching for GSM network

– GSM LED flashes once every second.

The tracker is attached to GSM network

– GSM LED flashes once every three seconds.

GSM modem is turned off

– GSM LED is OFF.

Indication of the battery charging

Battery charging

– NAVIGATION / CHARGING LED flashes green and red simultaneously

once a second.

When turning on the tracker for the first time it can take up to 26 seconds to start normal operation.
In normal operation mode the NAVIGATION / CHARGING LED flashes green and the GSM LED flashes
orange once every three seconds.

NOTE

AutoGRAPH-Mobile • USER MANUAL

Drivers Installation

This section covers the installation procedure of the AutoGRAPH-Mobile tracker drivers.

Fig.1.

Browse to the location where the drivers are saved (Fig.3).

Install the driver. When the driver is installed the system will automatically identify

connected device (Fig.4).

Install drivers for the AutoGRAPH CDC device following the outlined instruction.

The AutoGRAPH-Mobile drivers (AGUSBDriver) can be downloaded for free from the official web site of
the manufacturer (www.tk-chel.ru). The drivers are compatible with Microsoft Windows XP, 7, Vista,
8, Server 2003, Server 2008 and Server 2012.

NOTE

To install the device drivers onto a Microsoft Windows 7 OS:

Connect the tracker to your PC using USB AM – USB microB 5pin data cable. The

system will automatically search for new equipment (Fig.1). For proper operation, it is

necessary to install drivers for both AutoGRAPH and AutoGRAPH CDC devices.

If the Internet connection is available, Windows 7 will automatically connect to

the Windows Update website and install suitable driver for the tracker. If the Internet

connection is not available, continue with the procedure outlined below.

Download the archived drivers folder from the official website of TechnoKom -

AGUSBDriver.zip file and extract files to a temporary directory on a hard drive.

Launch the driver update wizard for new equipment (AutoGRAPH device) and select

“Browse my computer for driver software” to search for drivers manually (Fig.2).

Fig.2.

AutoGRAPH-Mobile • USER MANUAL

Connection to PC

For configuration the tracker and reading the data, it is necessary to connect the AutoGRAPH-

Mobile to a PC. Use USB AM – USB microB 5pin data cable to connect the device to a PC.

To connect the device to a PC:

•  Turn on the tracker.
•  Connect the data cable to mini USB connector of the tracker.
•  Connect the other end of the cable to the PC.
•  If the device drivers have been installed previously, the system will automatically identify

the connected device.
•

The tracker is now ready to operate with the MobileConf configuration program .

Care & Maintenance

Following simple instructions described below, you can maximize the tracker performance.

•  Keep it away from extreme temperatures.
•  Avoid excess moisture and exposure of chemical substances.
•  Don’t drop it and keep it safe.
•  Use only batteries and chargers, approved by the manufacturer. Using incompatible

batteries can damage the tracker.

Fig.3.

Fig.4.

Drivers for the AutoGRAPH-Mobile are successfully installed. The device is ready to

operate with troubleshooting utilities, dispatch software and other applications.

AutoGRAPH-Mobile • USER MANUAL

AutoGRAPH-Mobile Events

AutoGRAPH-Mobile records different events during the operation, e.g. SOS button pressing.

Every event is recorded in a certain data field. To review the device event in the AutoGRAPH

5 Dispatch Software, display data field which that event is recorded in.

The list of AutoGRAPH-Mobile events and data fields, which those events are recorded in,

are given in the table below.

The events of AutoGRAPH-Mobile personal tracking devices equipped with speed dialling buttons on the

front panel

Event

Data field

Button 1 pressed

Digital input 1

Button 2 pressed

Digital input 2

Button 3 pressed

Digital input 3

Button 4 pressed

Digital input 4

Call answer button pressed

Digital input 5

Call decline button pressed

Digital input 6

SOS button pressed

Digital input 7, Alarm button flag

Motion start

Digital input 8, Motion start flag

The events of AutoGRAPH-Mobile personal tracking devices with serial number 515ХХХХ (5150000) and

higher (equipped with big SOS button on the front panel)

Event

Data field

SOS button pressed

Digital input 1, Alarm button flag

Service record

Digital input 2

Service record

Digital input 3

Service record

Digital input 4

Service record

Digital input 5

Service record

Digital input 6

Service record

Digital input 7

Motion start

Digital input 8, Motion start flag

www.tk-nav.com

info@tk-nav.com

TechnoKom ltd.

VEHICLE AND PERSONAL TRACKING SYSTEM

AutoGRAPH

GPS

GLONASS

www.tk-nav.com

info@tk-nav.com

TechnoKom ltd.

VEHICLE AND PERSONAL TRACKING SYSTEM

AutoGRAPH

GPS

GLONASS

Ask a Question ?