Full Text Searchable PDF User Manual
© Copyright 2013 P1 / 16
User Manual
TecSys GmbH www.tecsys.de
Version 1.0 March. 2013
© Copyright 2013 P2 / 16
Contents
Welcome
4
Package contents ........................................................... 4
Getting to know
5
Front view ..................................................................... 5
Rear view ...................................................................... 6
Optional I/O interface .................................................... 7
Specification
8
Installation Guide
9
Take our the system unit ................................................ 9
Install the Power Adapter .............................................. 10
Install a LCM Customer Display ...................................... 11
Install a Second Display ................................................ 12
2nd VGA Power Setting ................................................. 13
Install the MSR / Fingerprint / iButton Module ................ 14
Version Change History
16
© Copyright 2013 P3 / 16
Notices
The information contained in this document is subject to change without notice.
We make no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose. We shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or use of this material.
Proprietary information contained in this document is copyright protected. Changes in this document or in the products
described herein may be made without prior notice.
TRADEMARK
Intel
®
/ Cedarview
®
are registered trademarks of Intel
®
Corporation. Microsoft
®
and Windows
®
are registered
trademarks of Microsoft Corporation.
Other trademarks mentioned herein are the property of their respective owners.
© Copyright 2013 P4 / 16
Welcome
The following illustration displays the package contents of your new product.
Package contents
POS
Power adapter
Power cord
COM-RJ45 cable (x2)
Driver CD
© Copyright 2013 P5 / 16
Getting to know
Front view
Fingerprint
Zero Bezel Touch screen
MSR
Base
I-Button
© Copyright 2013 P6 / 16
Rear view
Cable cover
LCM display
Peripheral dummy cover
Peripheral dummy cover
2
nd
display dummy cover
2
nd
display
Power button
© Copyright 2013 P7 / 16
Optional I/O interface
© Copyright 2013 P8 / 16
Specification
POS
Main Board
CPU
Intel CedarView D2550 processor 1.86 GHz 1M Cache
Chipset
NM10
System Memory
SO-DIMM DDR3 x1, total up to 4G 1066MHz
cooling
Fanless
Display
LCD Size
15" LCD
Brightness
300nits
Resolution
1024 x 768
Touch Screen
True Flat Resistive touch
True Flat P-CAP touch (option)
Storage
HDD Type
1 x 2.5” SATA HDD
External I/O Ports
DC Input
1 (19V-IN)
Cash Drawer
1 x RJ 11 (24V)
LAN(10/100/1000)
1
USB Port
4 x USB 2.0
VGA Port
1 (12V power enabled by BIOS)
Serial Port
RJ48 x 4 (COM3 5V/0.5A ; COM4 12V/0.5A selected by BIOS setting)
Power Switch
1
Expansion
mini PCI-E Socket
1
AUDIO
Internal Speaker
2x2W
Peripherals
2nd Display
10.4
”
LCD (800x600)
LCM Display
Char. x line 2x20 ( USB interface )
MSR
ISO 3-Tracks Slim MSR ( USB interface )
I-Button
1 (USB interface )
Fingerprint
1 (USB interface )
OS Support
Windows Embedded POSReady 2009,Windows XP Professional for Embedded,Windows 7
Power Supply
65W/19V-4pin Lock
Certifications
FCC, Class A, CE, LVD
Dimensions ( W x D x H )
430x215x330
Weight
5.86KG
Operating Temperature
0°C ~ 35°C (32°F ~ 95°F)
Storage Temperature
-20°C ~ 60°C (-4°F ~ 140°F)
Humidity
20% ~ 85% RH non condensing
© Copyright 2013 P9 / 16
Installation Guide
Take our the system unit
1.
Take the system unit out of the carton. Remove the unit from the carton by holding it by the foam inserts.
2.
Another carton includes the accessories: Power adapter (65W), power cord, COM-RJ45 cable(x2), and Driver CD.
© Copyright 2013 P10 / 16
Install the Power Adapter
1.
Remove the Cable cover.
2.
Route the power adapter through the stand gap.
3.
Connect the cable to the DC-IN port on system IO panel.
①
②
③
© Copyright 2013 P11 / 16
Install a LCM Customer Display
1.
Place the system face down. Make sure not to scratch the screen. Remove the 2 x screws to open the dummy
cover.
2.
Assemble the LCM customer display hinge into the customer display slot and fasten 2 x screws. Route the LCM
display cable through the stand gap as shown in the picture.
3.
Open the cable management and connect the LCM customer display into any USB ports.
①
②
③
© Copyright 2013 P12 / 16
Install a Second Display
1.
Place the system face down. Make sure not to scratch the screen. Remove the 2 x screws to open the dummy
cover.
2.
Assemble the 2
nd
display hinge into the customer display slot and fasten 2 x screws. Route the 2
nd
display cable
through the stand gap as shown in the picture.
3.
Open the cable management and connect the 2
nd
display into VGA port and adjust voltage to +12V in BIOS (refer
to Chapter 6)
①
②
③
© Copyright 2013 P13 / 16
2nd VGA Power Setting
1.
Power on the system, and press the <DEL> key when the system is booting up to enter the BIOS Setup utility.
2.
Select the Advanced tab.
3.
Select
VGA/COM Power and LCD Brightness Configuration
Ports and press <Enter> to go to display the
available options.
4.
To switch on the power, select
"+12V" press <Enter>. Please
save the change by pressing F10.
© Copyright 2013 P14 / 16
Install the MSR / Fingerprint / iButton Module
MSR/Fingerprint/iButton module can be installed to either side of the system. Choose one side and follow the steps
below. Make sure the unit is powered down before starting.
1.
Open the diverse cover.
2.
Connect MSR/Fingerprint/iButton to System connector.
3.
Insert the MSR/Fingerprint/iButton in place and fasten the screw on the back to secure the module.
MSR
Fingerprint
iButton
© Copyright 2013 P15 / 16
Safety information
IMPORTANT SAFETY INSTRUCTIONS
1)
Carefully read and follow these instructions. Pay attention to the danger and caution labels displayed on the
product.
2)
Only operate the product based on the type of power indicated on the label. Consult your dealer or local power
company if unsure of the type of power available.
3)
Make sure the power cord is placed safely where it would not be walked on. Do not rest anything on the power
cord.
4)
In disconnecting the machine from the electrical power supply, first switch off the power button, and then remove
the power plug from the wall socket.
5)
This product must not be placed on an unstable platform such as a stand or table for its fall may cause serious
damage to the product.
6)
Slots and openings are there to provide proper ventilation, prevent overheating and ensure reliable operation of
the product, thus must not be blocked or covered. Do not place the product on a bed, sofa, rug or the like so as to
avoid blocking the openings. Unless proper ventilation is provided, never place the product over or near a radiator,
heat register or a built-in installation.
7)
Never insert any kind of objects through the openings/slots to avoid touching dangerous voltage points which
could cause electric shock or fire.
8)
If there is smoke or strange smell, unplug the power cord from the power outlet immediately and request repair
from your dealer.
CE
This device complies with the requirements of directive 2004/108/EC with regard to “Electromagnetic
compatibility”.
FCC
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause
undesired operation
© Copyright 2013 P16 / 16
Version Change History
Version
Change Date
Change Content
V1.0
March, 2013
1
st
Release