SEWOO LK-P43 User Manual - User Manual

Download PDF User Manual

Full Text Searchable PDF User Manual

All specifications are subject to change without notice

USER’S MANUAL

MODEL : LK-P43

SEWOO TECH CO.,LTD.

374-2, Gajang-dong, Osan-si, Gyeonggi-do, 447-210, Korea

TEL : +82-31-459-8200 FAX : +82-31-459-8880

www.miniprinter.com

P43 Rev. A 06/13

Table of Contents

Safety Caution

2. Unpacking

3. Product Overview

4. Installation & Usage

4-1. Display

4-2. Installing the Battery

4-3. Removing the Battery

4-4. Charging the Battery

4-5. Installing Belt Clip

4-6. Interface Cap Installation

4-7. Roll Paper Installation

4-8. Install / Uninstall the External Paper Guides

4-9. Peel Mode

4-10. Shoulder Strap Installation

4-11. Diagnostic Test

5. Peripherals Connection

5-1. Interface Cable Connection

6. Printer Cleaning

6-1. Print-Head Cleaning

6-2. Platen Roller Cleaning

7. Pritner Specification

7-1. Specification

8. CPCL Command Compatibility

9. ESC/POS Command Compatibility

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTION

For higher reliability and safety, consider the following precautionary measures.
Read and follow the instructions carefully before running of the product.

1. Safety Caution

WARNING

Failure to follow these instructions could result in fire, electric shock,
or other injuries, or property damage

Indication

Prohibition

(Potential risk of electric shock or fire)

(Turn off the power at installation,
transportation, wiring and inspection.)

(You may get hurt and it can be broken
when it falls)

(Potential risk of fire or unit malfunction)

(Potential risk of discoloration or
electric shock)

(Potential risk unit malfunction, electric
shock or fire. When the product needs
to be repaired, please contact in place
where you ordered.inspection.)

(Potential risk of electric shock or fire)

Must follow

Do not disassemble

Unplug the power from
the outlet

Grounding to prevent
electric shock

Do not handle the product
with wet hands

Dealer

Do not pull or touch the power plug
with wet hands.

Do not pull out the power plug to turn
off the product.

Do not install the product in uneven or
inclined surface.

If the product that needs to be repaired,
please contact in place where you
ordered.

Please do not give excessive shock.

Keep product away from the water
and other material.

Do not disassemble, repair or modify
the product.

Do not bend the wire and do not allow
the wire to be pressed by heavy object.

If a power plug is broken or a plug is
cut or worn, do not use it.

Do not overload the power plug into
one outlet.

CAUTION

SHOULDER
STRAP RING

3. Product Overview

CHARGER
CONNECTOR

COVER OPEN
BUTTON

Front

Bottom

PEELER BODY

PEELER WING

BATTERY

BELT CLIP
CONNECTOR

SERIAL

USB

DISPLAY

2. Unpacking

Printer

Battery

Belt Clip

AC cord

Optional

Standard

USB Cable

Quick Reference

Adaptor

Paper

Shoulder Strap

Serial Cable

4-1. Display

4. Setting Up the Product

Button

Name

unction

Paper Feed /
Down Button

Advances the supply.  Clears error message.
Moves down through menu options.
1. Refer to 4-9 for Diagnostic  Test  information.
2. Refer to the service manual regarding Hexadecimal
     Dumping.

Enter Button

Selects the highlighted menu option.

Up Button

Moves up through menu options.

Power Button

Turns the printer on and off.  Press to turn
power on.  Press for three seconds to turn power off.
Wakes the printer from  sleep mode.

NOTE

1. The battery status LEDs indicate amount of power remaining.
    Actual run-time remaining depends on factors such as the contents of output,
    distance to computer, etc.
2. When the battery level is very low, high density printing can result in the printer
    switching off during printing resulting in possible loss of data.

4-2. Installing the Battery

NOTE

Remove the battery. Insert the battery as shown.
Replace the battery.

You must fully charge the battery when you receive the printer.
Batteries can be charged in the printer or in an optional external cradle.

4-3. Removing the Battery

Remove the battery. Lift out the battery.

4-4. Charging the Battery

1. Be sure that the printer is turned off
2. After open the DC JACK cover, insert DC JACK into the printer.
3. Plug the power code to electrical outlet.

3-4-1 The status of lamp in charging

Status Charging Charging Completed

Charging Lamp

Red

Green

If there is trouble while charging the battery, the charge indicator LED blinks green.
Try unplugging and reconnecting charger, charging should resume.
Charging is complete when the LED changes to solid green.

NOTE

The belt clip is included with the printer but is not required to be used or installed!

4-5. Belt Clip Usage

Insert screw into belt clip.

Tighten the screw with driver as shown.

NOTE

4-6. Interface Cap Installation

1 2

3 4

When Interface Cap separated from

the printer, try to array the Cap Hook

in horizontal direction as shown in the

image.

Using a sharp tool, insert the Cap

Hook to the hole which is located in

the right side of Interface Cap.

When Cap Hook inserted, install the Cap

Cover in direction of an arrow as shown

in the image.

Close the Interface Cap cover.

NOTE

If the users close the cover with one hand,

it would not be closed completely.

Please use both hands to close.

4-7. Roll Paper Installation

1 2

3 4

Put the stock in so it unrolls from the

bottom. Remove the stock core when

it is empty. Pull a short length of stock

out of the printer.

Open the Paper cover by pressing the

Open button and set the width of paper

guide by turning the knob with finger.

After inserting the paper, adjust the

paper guide to little wider than paper size.

Then pull the paper out and close the

paper cover.

Close the Paper cover with both hands

and run the paper line up by pressing

the Feed button.

Be cautious to handle the product when Printer Cover is an open position.

You may have a potential risk of injury when Paper Cover closes

CAUTION

Using sharp tool, push External Paper

Guides in order to detach from the

printer. Press circle on the middle of

external paper guide with tool.

Assemble two (inner & outer) External

Paper Guides as shown in figure and

press three points to fix firmly inner

guide with outer guide.

The outer cover of External Paper Guides
will be separated.

Two external paper guides will be
installed to printer.

External Paper
Guides

4-8. Install / Uninstall the External Paper Guides

Uninstall the External Paper Guides

Install the External Paper Guides

1 2

When install the external paper, set the printer 20mm above from the

ground. Then insert the paper in right direction to the backside of the

printer paper slot and adjust the paper guide to fit the paper properly.

Please set apart the printer and paper at least

twice of the paper length.

Recommendation

300mm이상

20mm이상

300mm이상

20mm이상

CAUTION

20mm or more

300mm or more

Paper (1)

Label Paper

Engraved Line

Paper (2)

Label Paper

When users operates the peeler like the image below that has
slits on the label(1) and the perforated label(2), there might be
an error in the peeler function

CAUTION

4-9. Peel Mode

1 2

With a roll of stock installed, slide the

peeler body towards the back of the

printer.

Press the Feed button.

Peel Mode

Non-Peel Mode

Push the peeler body until you see

two complete triangles.

Press the Feed button.

Pull down the Peeler Wing while pressing

the Cover open button slightly.

Insert the strap into the hook of the printer.

Place the end of the strap into the

hook of shoulder strap.

After pulling out the end of the strap tightly,

put it into the clip to be fastened.

Optional

4-10. Shoulder Strap Installation

4-11. Diagnostic Test

1 2

NOTE

Turn off the printer.

The information label prints.

Press and hold the Feed button

and Power button.

1. For Hex Dump mode, do steps 1-2 then

press the Feed button.
2. After printing ASCII pattern, the diagnostic

test is complete.
3. If the Feed button is not pressed to go to

Hex Dump mode, the printer exits

diagnostics after three seconds.

The Sample of Self-test Printout

Upon initial installation or for troubleshooting, you can run the diagnostic test to

get information about:

Firmware version, emulation, codepage, sensor settings, interface settings, etc.

If no issues are found with diagnostic test, examine other devices and software.

The diagnostic test is working independent of devices and software.

●

Do Not Overheat the Motor

To prevent the motor from overheating, stop the printer for at least 30 seconds after
continuously printing 1.5 meters.

5. Peripherals Connection

5-1. Interface Cable Connection

1. Connect the USB or Serial cable to the cable connector on the printer.

2. Connect the interface cable into the USB or Serial port of the device
(PDA, PC, etc.)

NOTE

Use cable only offered by the printer manufacturer.

Serial

USB

6-1. Print-Head Cleaning

6. Printer Cleaning

If the interior of the printer is dusty, printing quality can be lowered.

In this case, follow the instructions below to clean the printer.

NOTE

1. Make sure to turn the printer power off prior to cleaning.
2. The print-head can become very hot during printing;
allow the printer approximately10 minutes to cool before cleaning.
3. Do not touch the print-head, it can be damaged by static electricity.
4. Take care not to allow the print head to become scratched and /or damaged
in any way.

1. Use an applicator swab moistened with an isopropyl alcohol to clean the

print-head and remove any dust.

2. Once cleaning is complete, allow the printer to dry then install the stock

and close the cover.

Print-Head

6-2. Platen Roller Cleaning

1.Clean the platen roller with a clean soft cloth moistened with isopropyl

alcohol or a cleaning pen.
2. Turn the platen roller with your finger to clean the entire surface.

Platen Roller

Printing Method

Direct Thermal

Printing Speed

80mm/sec

Resolution

203 DPI X 203 DPI

Character

ALPHA NUMERIC Character, Extension Character

Barcode

One-Dimensional
Barcodes

UPCA +2/+5, UPCE +2/+5, EAN8 +2/+5,
EAN13 +2/+5, EAN 128, Interleaved 2 of 5,
Extended Code 39, Codabar (NW7), Code 128,
Code 93, PostNet

Two-Dimensional
Barcodes

PDF417, MaxiCode, Aztec, QR Code (Quick Response),
Datamatrix

Stacked One-
Dimensional
Barcodes

GS1 Databar (RSS or Composite Code)

Emulation

ESC/POS, ZPL, CPCL Command compatible

Driver

Windows (2000, XP, Vista, 7, 8), Symbian OS
Windows mobile(Pocket PC, 2003, 6x), Android,
Windows CE 4.2/5.0/6.0, Linux, Blackberry

Sensor

Black-Mark Upper/Lower, Gap, Cover open,
Peeler Detect, Peeler S/W, Media-Width Detect

Paper

Paper Type

Thermal Paper

Width

112mm

Thickness

Roll : 0.06 ~ 0.165 mm / Fanfold : 0.06~0.15 mm

External Diameter

Max.

58mm

Internal Diameter

12.5mm±0.5mm

Reliability

TPH

25.4km (1,000,000in)

Battery

Continuous Printing 62min
Standby for 60hours
Printing Length: 140M

Communications

Serial(RS-232C), USB

7-1. Specification

7. Printer Specification

Display

TFT-LCD (RGB) 240X400

Adaptor

Input

AC 100 ~240V 50/60Hz

Output

9.0V, 4.0A

Battery

Battery Type

Li-ion

Output

7.4V, 19.24wh

Charging Time

3.7 Hrs Charging

Size

WXDXH(mm)

166 X 174 X 82

WXDXH”

6.5 X 6.9 X 3.2

Weight

1Kg (With battery)

Environment Sealing

IP44

Temperature

Operation

-10 ~ 50

℃

Storage

-20 ~ 60

℃

Humidity

Operation

35 ~ 80%

Storage

10 ~ 90%

Printer Commands

Compatibility

○

FORM

○

JOURNAL

○

UNITS

○

Comments

○

TEXT

Compatibility

TEXT

○

FONT-GROUP(FG)

○

TEXT CONCATENATION

○

MULTILINE(ML)

○

COUNT

○

SETMAG

○

SCALABLE TEXT

Linear Bar Codes

Compatibility

BARCODE

○

BARCODE-TEXT

○

Two-Dimensional Bar Codes

Compatibility

PDF417 (PORTABLE DATA FILE)

○

MAXICODE

○

QRCODE

●

DATAMATRIX

●

GS1(RSS)

●

NOTE

Compatible

Partially
Compatible

Not Compatible

○

●

△

Compatible with only

commanders provided by

the manufacturer.

8. CPCL Command Compatibility

Graphics

Compatibility

BOX

○

LINE

○

INVERSE-LINE

○

PATTERN

○

GRAPHICS

○

PCX

○

Advanced Commands

Compatibility

CONTRAST

○

TONE

○

JUSTIFICATION

○

PAGE-WIDTH

○

PACE

○

NO-PACE

○

WAIT

○

REWIND

TENSION

SPEED

○

SETSP

○

ON-OUT-OF-PAPER

ON-FEED

○

PREFEED

○

POSTFEED

○

PRESENT-AT

COUNTRY/CODE PAGE

○

FORMAT FILES

○

BEEP

○

CUT

PATIAL-CUT

MCR

●

Line Print Mode

Compatibility

SETLP

○

SETLF

○

Moving With X and Y Coordinates

○

LMARGIN

○

SETBOLD

○

SETSP

○

Special ASCII Characters

○

SETFF

○

SET-TOF

○

SETLP-TIMEOUT

○

ESC / POS

Command Compatibility

No.

Command

Function

Horizontal tab

Print and line feed

Print and carriage return

Print end position label to start printing

CAN

Cancel print data in page mode

DLE EOT

Real-time status transmission

DLE ENQ

Real-time request to printer

ESC FF

Print data in page mode

ESC SP

Set character right-side spacing

ESC !

Set print mode

ESC $

Set absolute print position

ESC %

Select/cancel user-defined character set

ESC &

Define user-defined characters

ESC *

Set bit image mode

ESC -

Turn underline mode on/off

ESC 2

Set 1/6 inch line spacing

ESC 3

Set line spacing using minimum units

ESC ?

Cancel user-defined characters

ESC @

Initialize printer

ESC D

Set horizontal tab positions

ESC E

Select emphasized mode

ESC G

Select double-strike mode

ESC J

Print end feed paper using minimum units

ESC L

Select page mode

ESC M

Select character font

ESC R

Select international character set

ESC S

Select standard mode

ESC T

Select print direction in page mode

ESC V

Set/cancel 90

cw rotated character

ESC W

Set printing area in page mode

ESC

＼

Set relative position

ESC a

Align position

ESC d

Print and feed paper n lines

ESC t

Select character code table

ESC {

Set/cancel upside-down character printing

FS p

Print NV bit image

FS q

Define NV bit image

GS !

Select character size

GS $

Set absolute vertical print position in page mode

GS *

Define downloaded bit image

GS /

Print down-loaded bit image

GS B

Turn white/black reverse printing mode on/off

GS H

Select printing position of HRI characters

GS I

Transmit printer ID

GS L

Set left margin

GS W

Set printing area width

＼

Set relative vertical print position in page mode

GS a

Enable/disable Automatic Status Back(ASB)

GS f

Select font for HRI characters

GS h

Set bar code height

GS k

Print bar code

GS r

Transmit status

GS v 0

Print raster bit image

GS w

Set bar code width

< Add >

101

GS S C

Set Serial Baudrate

102

DLE EOT n

Selects card read mode / Cancel card read mode

103

GS S P

Power Save Mode