Porter-Cable MODEL 505 Instruction Manual - User Manual

Full Text Searchable PDF User Manual

Instruction

manual

The Model and Serial No. plate is located on the main
housing of the tool. Record these numbers in the
spaces below and retain for future reference.

Model No. ______________________________________

Type ___________________________________________

Serial No. _______________________________________

IMPORTANT

Please make certain that the person who is
to use this equipment carefully reads and
understands these instructions before
starting operations.

ESPAÑOL: PÁGINA 15
FRANÇAISE : PAGE 29

To learn more about Porter-Cable

visit our website at:

http://www.porter-cable.com

Part No. 907436 - 03-0

-05

Finishing Sander

MODEL

505

Read and understand all warnings and operating instructions

before using any tool or equipment. When using tools or equipment, basic
safety precautions should always be followed to reduce the risk of personal
injury. Improper operation, maintenance or modification of tools or equipment
could result in serious injury and property damage. There are certain
applications for which tools and equipment are designed. Porter-Cable strongly
recommends that this product NOT be modified and/or used for any application
other than for which it was designed.

If you have any questions relative to its application DO NOT use the product
until you have written Porter-Cable and we have advised you.

Online contact form at

www.porter-cable.com

Postal Mail: Technical Service Manager

Porter-Cable Corporation

4825 Highway 45 North
Jackson, TN 38305

Information regarding the safe and proper operation of this tool is available from
the following sources:
Power Tool Institute
1300 Sumner Avenue, Cleveland, OH 44115-2851

www.powertoolinstitute.org

National Safety Council
1121 Spring Lake Drive, Itasca, IL 60143-3201

American National Standards Institute, 25 West 43rd Street, 4 floor, New York,
NY 10036

www.ansi.org

ANSI 01.1Safety Requirements for Woodworking

Machines, and the U.S. Department of Labor regulations

www.osha.gov

SAVE THESE INSTRUCTIONS!

IMPORTANT SAFETY INSTRUCTIONS

. . . . . . . . . . . . . . . . . . . . . . . . . .2

SAFETY GUIDELINES

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

GENERAL SAFETY RULES

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

ADDITIONAL SPECIFIC SAFETY RULES

. . . . . . . . . . . . . . . . . . . . . . . .6

ADDITIONAL SAFETY RULES FOR PAINT REMOVAL

. . . . . . . . . . . . .6

CARTON CONTENTS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

FUNCTIONAL DESCRIPTION

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

ASSEMBLY

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

OPERATION

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

TROUBLESHOOTING

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

MAINTENANCE

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

SERVICE

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

ACCESSORIES

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

WARRANTY

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

ESPAÑOL

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

FRANÇAISE

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

SERVICE CENTER LOCATIONS . . . . . . . . . . . . . . . . . . . . . . .

back cover

TABLE OF CONTENTS

IMPORTANT SAFETY INSTRUCTIONS

Some dust created by power sanding, sawing, grinding, drilling,

and other construction activities contains chemicals known (to the

State of California) to cause cancer, birth defects or other reproductive harm. Some

examples of these chemicals are:

●

lead from lead-based paints

●

crystalline silica from bricks and cement and other masonry products

●

arsenic and chromium from chemically-treated lumber

Your risk from these exposures varies, depending on how often you do this

type of work. To reduce your exposure to these chemicals: work in a well

ventilated area, and work with approved safety equipment, always wear

NIOSH/OSHA approved, properly fitting face mask or respirator when using

such tools.

indicates an imminently hazardous situation which, if not

avoided, will result in death or serious injury.

indicates a potentially hazardous situation which, if not

avoided,could result in death or serious injury.

indicates a potentially hazardous situation which, if not

avoided,may result in minor or moderate injury.

used without the safety alert symbol indicates potentially

hazardous situation which, if not avoided, may result in

property damage.

CALIFORNIA PROPOSITION 65

It is important for you to read and understand this manual. The
information it contains relates to protecting YOUR SAFETY and
PREVENTING PROBLEMS. The symbols below are used to help
you recognize this information.

SAFETY GUIDELINES - DEFINITIONS

Read all instructions. Failure to follow all

instructions listed below may result in electric shock, fire and/or

serious injury. The term "power tool" in all of the warnings listed

below refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

SAVE THESE INSTRUCTIONS

1) Work area safety

Keep work area clean and well lit.

Cluttered or dark areas invite

accidents.

Do not operate power tools in explosive atmospheres, such as in the

presence of flammable liquids, gases or dust.

Power tools create

sparks which may ignite the dust or fumes.

Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety

Power tool plugs must match the outlet. Never modify the plug in any

way. Do not use any adapter plugs with earthed (grounded) power
tools.

Unmodified plugs and matching outlets will reduce risk of electric

shock.

Avoid body contact with earthed or grounded surfaces such as

pipes, radiators, ranges and refrigerators.

There is an increased risk of

electric shock if your body is earthed or grounded.

Do not expose power tools to rain or wet conditions.

Water entering a

power tool will increase the risk of electric shock.

Do not abuse the cord. Never use the cord for carrying, pulling or

unplugging the power tool. Keep cord away from heat, oil, sharp
edges or moving parts

. Damaged or entangled cords increase the risk

of electric shock.

When operating a power tool outdoors, use an extension cord

suitable for outdoor use.

Use of a cord suitable for outdoor use reduces

the risk of electric shock.

3) Personal safety

Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired
or under the influence of drugs, alcohol or medication.

A moment of

inattention while operating power tools may result in serious personal
injury.

Use safety equipment. Always wear eye protection.

Safety equipment

such as dust mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce personal injuries.

Avoid accidental starting. Ensure the switch is in the off-position

before plugging in

. Carrying power tools with your finger on the switch

or plugging in power tools that have the switch on invites accidents.

GENERAL SAFETY RULES

Remove any adjusting key or wrench before turning the power tool

on.

A wrench or a key left attached to a rotating part of the power tool

may result in personal injury.

Do not overreach. Keep proper footing and balance at all times.

This

enables better control of the power tool in unexpected situations.

Dress properly. Do not wear loose clothing or jewelry. Keep your

hair, clothing and gloves away from moving parts.

Loose clothes,

jewelry or long hair can be caught in moving parts.

If devices are provided for the connection of dust extraction and

collection facilities, ensure these are connected and properly used.

Use of these devices can reduce dust-related hazards.

4) Power tool use and care

Do not force the power tool. Use the correct power tool for your

application.

The correct power tool will do the job better and safer at the

rate for which it was designed.

Do not use the power tool if the switch does not turn it on and off.

Any power tool that cannot be controlled with the switch is dangerous
and must be repaired.

Disconnect the plug from the power source before making any

adjustments, changing accessories, or storing power tools.

Such

preventive safety measures reduce the risk of starting the power tool
accidentally.

Store idle power tools out of the reach of children and do not allow

persons unfamiliar with the power tool or these instructions to
operate the power tool.

Power tools are dangerous in the hands of

untrained users.

Maintain power tools. Check for misalignment or binding of moving

parts, breakage of parts and any other condition that may affect the
power tools operation. If damaged, have the power tool repaired
before use.

Many accidents are caused by poorly maintained power

tools.

Keep cutting tools sharp and clean.

Properly maintained cutting tools

with sharp cutting edges are less likely to bind and are easier to control.

Use the power tool, accessories and tool bits etc., in accordance

with these instructions and in the manner intended for the
particular type of power tool, taking into account the working
conditions and the work to be performed.

Use of the power tool for

operations different from those intended could result in a hazardous
situation.

5) Service

Have your power tool serviced by a qualified repair person using only

identical replacement parts.

This will ensure that the safety of the

power tool is maintained.

GENERAL SAFETY RULES

continued

ADDITIONAL SPECIFIC SAFETY RULES

SAVE THESE INSTRUCTIONS!

Hold power tools by insulated gripping surfaces when performing an
operation where the cutting tool may contact hidden wiring or its own
cord.

Contact with a "live" wire will make exposed metal parts of the tool

"live" and shock the operator.

Use proper safety equipment.

Wear safety goggles for eye protection, wear

hearing protection, and wear a protective mask to minimize breathing in the
fine dust created while sanding.

Always disconnect the sander cord plug from the power circuit before
changing abrasive sheets.

Such preventive safety measures reduce the

risk of starting the power tool accidentally.

Sanding of lead-based paint is not recommended.

Lead-based paint

should only be removed by a professional.

Always maintain a firm grip on the sander handles

with both hands to

prevent loss of control.

Do not operate sander without all guards and covers

securely in place.

Wear eye and hearing protection. Always use safety glasses.

Everyday

eyeglasses are NOT safety glasses. USE CERTIFIED SAFETY EQUIPMENT.
Eye protection equipment should comply with ANSI Z87.1 standards.
Hearing equipment should comply with ANSI S3.19 standards.

Use of this tool can generate and disburse dust or other

airborne particles, including wood dust, crystalline silica dust and
asbestos dust.

Direct particles away from face and body. Always operate

tool in well ventilated area and provide for proper dust removal. Use dust
collection system wherever possible. Exposure to the dust may cause
serious and permanent respiratory or other injury, including silicosis (a
serious lung disease), cancer, and death. Avoid breathing the dust, and
avoid prolonged contact with dust. Allowing dust to get into your mouth or
eyes, or lay on your skin may promote absorption of harmful material.
Always use properly fitting NIOSH/OSHA approved respiratory protection
appropriate for the dust exposure, and wash exposed areas with soap and
water.

SYMBOL

DEFINITION

........................ volts

........................ amperes

........................ hertz

........................ watts

........................ kilowatts

........................ farads

µF

........................ microfarads

........................ litres

........................ grams

........................ kilograms

bar

........................ bars

........................ pascals

........................ hours

min

........................ minutes

........................ seconds

........................ no-load speed

…/min or …min-

......... Revolutions or reciprocations per minute

or d.c. ................ direct current

or a.c. ................ alternating current

........................ two-phase alternating current

........................ two-phase alternating current with neutral

........................ three-phase alternating current

........................ three-phase alternating current with neutral

........................ rated current of the appropriate fuse-link in amperes

........................ time-lag miniature fuse-link where X is the symbol

for the time/current characteristic, as given in IEC 60127

........................ protective earth

........................ class II tool

IPXX

........................

symbol

SAVE THESE INSTRUCTIONS!

Extreme care should be taken when removing paint. The
peelings, residue, and vapors of paint may contain lead, which
is poisonous. Exposure to even low levels of lead can cause
irreversible brain and nervous system damage. Young and
unborn children are particularly vulnerable.

Before beginning any paint removal process you should determine whether the
paint you are removing contains lead. This can be done by your local health
department or by a professional who uses a paint analyzer to check for lead.

Lead-based paint should only be removed by a professional.

Persons removing paint should follow these guidelines:

Keep the work area well ventilated.

Open the windows and put an

exhaust fan in one of them. Be sure the fan is moving air from inside to outside.

Remove or cover any carpets, rugs, furniture, clothing, cooking

utensils, and air ducts.

Such preventive safety measures reduce the risk of

exposure.

Place drop cloths in the work area to catch any paint chips or peelings.

Wear protective clothing such as extra work shirts, overalls and hats.

Such

preventive safety measures reduce the risk of exposure.

Work in one room at a time.

Furnishings should be removed or placed in

the center of the room and covered. Work areas should be sealed off from the
rest of the dwelling by sealing doorways with drop cloths.

Children, pregnant, or potentially pregnant women and nursing

mothers should not be present in the work area until the work is done and
all cleanup is complete.

Such preventive safety measures reduce the risk of

injury.

Wear a dust respirator or a dual filter (dust and fume) respirator mask

which has been approved by the Occupational Safety and Health
Administration (OSHA), the National Institute of Safety and Health (NIOSH),
or the United States Bureau of Mines.

These masks and replaceable filters are

readily available at major hardware stores. Be sure the mask fits. Beards and
facial hair may keep the masks from sealing properly. Change filters often.
DISPOSABLE PAPER MASKS ARE NOT ADEQUATE.

Keep food and drink out of the work area.

Wash hands, arms, and face

and rinse mouth before eating or drinking. Do not smoke or chew gum or
tobacco in the work area.

Clean up all removed paint and dust by wet mopping the floors

. Use a

wet cloth to clean all walls, sills and any other surfaces where paint or dust is
clinging. DO NOT SWEEP, DRY DUST OR VACUUM. Use a high phosphate
detergent or trisodium (TSP) to wash and mop areas.

At the end of each work session, put the paint chips and debris in a

double plastic bag, close it with tape or twist ties and dispose properly.

Such preventive safety measures reduce the risk of exposure.

10. Remove protective clothing and work shoes in the work area to avoid
carrying dust into the rest of the dwelling.

Wash work clothes separately. Wipe

shoes off with a wet rag, then wash that rag with the work clothes. Wash hair and
body thoroughly with soap and water.

SAVE THESE INSTRUCTIONS!

ADDITIONAL SAFETY RULES FOR PAINT REMOVAL

If an extension cord is used, make sure the conductor size is large enough to
prevent excessive voltage drop which will cause loss of power and possible
motor damage. A table of recommended extension cord sizes will be found in
this section. This table is based on limiting line voltage drop to 5 volts (10 volts
for 230 volts) at 150% of rated amperes.

If an extension cord is to be used outdoors, it must be marked with the suffix W-
A or W following the cord type designation. For example – SJTW-A to indicate it
is acceptable for outdoor use.

RECOMMENDED EXTENSION CORD SIZES FOR USE WITH PORTABLE ELECTRIC TOOLS

Length of Cord in Feet

115V

25 Ft.

50 Ft.

100 Ft.

150 Ft.

200 Ft.

250 Ft.

300 Ft.

400 Ft.

500 Ft.

230V

50 Ft.

100 Ft.

200 Ft.

300 Ft.

400 Ft.

500 Ft.

600 Ft.

800 Ft. 1000 Ft.

0-2

2-3

3-4

4-5

5-6

6-8

8-10

10-12

12-14

14-16

16-18

18-20

Nameplate Ampere Rating

EXTENSION CORD SELECTION

MOTOR

Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60
cycle A.C. current and voltage within plus or minus 5 percent of that shown on
the specification plate on the tool. Several models, however, are designed for
A.C. current only. Refer to the specification plate on your tool for proper voltage
and current rating.

Do not operate your tool on a current on which the voltage is not
within correct limits. Do not operate tools rated A.C. only on D.C.
current. To do so may seriously damage the tool.

1) Sander
2) Instruction Manual
3) Replacement Parts List
4)One Abrasive Sheet

CARTON CONTENTS

SAVE THESE INSTRUCTIONS!

FOREWORD

Your Porter-Cable Finishing Sander is equipped to accept adhesive backed
abrasives (4

" width) or conventional abrasive sheets (4

" x 11").

This Sander is suitable for coarse, medium, or fine sanding of wood, plaster,
metal, and plastics. It is ideal for leveling wallboard joints, finishing cabinets,
rubbing and polishing furniture, fitting screens and doors, or for general
finishing work.

NOTE: This tool is shipped completely assembled. No assembly time or

tools are required.

SELECTING THE RIGHT ABRASIVE SHEET

When you select the proper type of abrasive, you can achieve the finest
finish on your work. In general, coarser grit sizes will remove the most
material and finer grit sizes will produce the best finishes.

You will obtain the best results if you select the proper size and type of
abrasives. Use only garnet, aluminum oxide, and silicon carbide with
finishing sanders. Flint paper is unsatisfactory for machine sanding due to its
weak structure.

Before starting to work, make sure you have the right abrasive for the
workpiece. Make sure you use the correct size abrasive paper or cloth. Cut,
do not tear, the abrasive sheets to size.

ATTACHING ADHESIVE BACKED ABRASIVES

Adhesive backed abrasives (ten
yard rolls) and a convenient
dispenser are available from your
Porter-Cable distributor.

To install adhesive backed
abrasives, cut a 9" long piece of
abrasive from roll, align abrasive
with sander pad, and press in
place (Fig. 1).

To remove the abrasive, warm the
pad for a few minutes, then lift one
corner with your fingernail and
peel off.

ATTACHING CONVENTIONAL ABRASIVES

Press the front clip toward the base and slip one end of the abrasive
sheet under the clamp (Fig. 2).

Stretch the abrasive sheet tightly over the pad (Fig. 3), and bend up over
the pad edge.

Press the rear clip toward the base. Slip the free end of the abrasive
sheet under the clamp (Fig. 4).

FUNCTIONAL DESCRIPTION

ASSEMBLY

Fig. 1

OPERATING THE SWITCH

This tool is equipped with a trigger
switch (A) Fig. 5. A switch locking
button (B) Fig. 5 is located on the
left side of the handle. Start the
motor by depressing the trigger.
Stop the motor by releasing the
trigger. To keep the motor running
without holding your finger on the
trigger, depress the trigger, push
in on the locking button and
release the trigger. To release the
locking button, depress the trigger
and release.

Make sure switch is off before inserting cord plug into power
circuit outlet.

Fig. 2

Fig. 3

Fig. 4

Fig. 5

OPERATION

STARTING TO WORK

This finishing sander has been designed for one or two hand operation, and
can easily be guided over the work surface. The normal weight of the
machine is sufficient for efficient sanding. Putting additional pressure on the
machine only slows down the speed of the pad, reduces the sanding
efficiency, and puts an additional burden on the motor. Also, additional
pressure might cause the sander to “jump”. Always start the machine
before placing it on the work surface. Once it has started, ease it down on
the work surface evenly and move it slowly back and forth in wide,
overlapping arcs. When you are through sanding, lift the sander off of the
work before stopping the motor.

WORKING PROCEDURE

The action of the Porter-Cable Finishing Sander causes thousands of tiny
abrasive grits to move in circular orbits against the work at high speed. Each
grain moves in the same direction at a constant speed so the cutting action
is uniform over the entire pad surface. Crossing and re-crossing of the
abrasive grits from all directions quickly levels surface irregularities to a fine,
uniform smoothness. Start the work with an abrasive grit just coarse enough
to remove the high spots and excessive roughness. Follow with a second
sanding using a grit one or two grades finer. Continue with successively
finer grits until the desired finish is obtained. DO NOT GO FROM A COARSE
GRlT TO A VERY FINE GRIT IN ONE STEP. Swirl marks will be impossible to
remove.

REQUIREMENTS FOR FINE FINISHING

In general, the coarser grits remove the most material in the shortest
time. The finer grits produce a smoother finish. By selecting the proper
type of abrasive, your workpiece can have a very smooth and even
finish.

REMOVING PAINT AND VARNISH

Read and follow instructions in “

ADDITIONAL SAFETY

RULES FOR PAINT REMOVAL

”.

Your sander will do a good job of removing old paint and varnish if you follow
these two instructions. First, use a coarse, open-coat abrasive to avoid the
usual clogging of the abrasive surfaces. Second, keep the machine moving
over new areas to avoid heating and softening the material being removed.
Try to work the entire surface at the same time by working in wide,
overlapping arcs. Do not concentrate on small areas. If liquid removers or
heaters are used to speed the work, be sure the surface is cool and dry and
the excess material has been scraped away before using the sander.

CABINETS AND DOORS

The orbital motion of the Porter-Cable Finishing Sander is ideally suited for
finishing doors, cabinet fronts, and other workpieces where wood grain is
perpendicular to that of a joining piece. Since the motion is circular, the
machine may be moved in any direction and crossed from one part to the
other without regard to direction of grain. A uniform and smooth finish will
result on both parts. The same procedure may be used to even joints in
cabinets The sander may be worked on both sides and in all directions to
obtain a smooth matching joint. By properly changing from coarser to finer
grit abrasives, you can achieve an excellent finish.

For assistance with your tool, visit our website at

www.porter-cable.com

for a

list of service centers or call the Porter-Cable help line at 1-800-487-8665.

TROUBLESHOOTING

KEEP TOOL CLEAN

Periodically blow out all air passages with dry compressed air. All plastic parts
should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic
parts. They could possibly dissolve or otherwise damage the material.

Wear ANSI Z87.1 safety glasses while using compressed air.

FAILURE TO START

Should your tool fail to start, check to make sure the prongs on the cord plug are
making good contact in the outlet. Also, check for blown fuses or open circuit
breakers in the line.

LUBRICATION

This tool has been lubricated with a sufficient amount of high grade lubricant for
the life of the unit under normal operating conditions. No further lubrication is
necessary.

BRUSH INSPECTION

(If applicable)

For your continued safety and electrical protection, brush inspection and
replacement on this tool should ONLY be performed by an AUTHORIZED
PORTER-CABLE SERVICE STATION or a PORTER-CABLE

•

DELTA FACTORY

SERVICE CENTER.

At approximately 100 hours of use, take or send your tool to your nearest
authorized Porter-Cable Service Station to be thoroughly cleaned and inspected.
Have worn parts replaced and lubricated with fresh lubricant. Have new brushes
installed, and test the tool for performance.

Any loss of power before the above maintenance check may indicate the need
for immediate servicing of your tool. DO NOT CONTINUE TO OPERATE TOOL
UNDER THIS CONDITION. If proper operating voltage is present, return your tool
to the service station for immediate service.

MAINTENANCE

PORTER-CABLE LIMITED

ONE YEAR WARRANTY

Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original
purchase. We will repair or replace at our option, any part or parts of the product and accessories
covered under this warranty which, after examination, proves to be defective in workmanship or
material during the warranty period. For repair or replacement return the complete tool or accessory,
transportation prepaid, to your nearest Porter-Cable Service Center or Authorized Service Station.
Proof of purchase may be required. This warranty does not apply to repair or replacement required
due to misuse, abuse, normal wear and tear or repairs attempted or made by other than our Service
Centers or Authorized Service Stations.

ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, WILL LAST ONLY FOR ONE (1) YEAR FROM THE DATE
OF PURCHASE.

To obtain information on warranty performance please write to: PORTER-CABLE CORPORATION,
4825 Highway 45 North, Jackson, Tennessee 38305; Attention: Product Service. THE FOREGOING
OBLIGATION IS PORTER-CABLE’S SOLE LIABILITY UNDER THIS OR ANY IMPLIED WARRANTY
AND UNDER NO CIRCUMSTANCES SHALL PORTER-CABLE BE LIABLE FOR ANY INCIDENTAL
OR CONSEQUENTIAL DAMAGES. Some states do not allow limitations on how long an implied
warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.

This warranty gives you specific legal rights and you may also have other legal rights which vary
from state to state.

WARRANTY

REPLACEMENT PARTS

When servicing use only identical replacement parts. For a service parts list or to
learn more about Porter-Cable visit our website at

www.porter-cable.com

SERVICE AND REPAIRS

All quality tools will eventually require servicing, or replacement of parts due to
wear from normal use. For assistance with your tool, visit our website at

www.porter-cable.com

for a list of service centers or call the Customer Care

Department at

1-800-487-8665.

All repairs made by our service centers are fully

guaranteed against defective material and workmanship. We cannot guarantee
repairs made or attempted by others.

Should you have any questions about your tool, feel free to write us at any time.
In any communications, please give all information shown on the nameplate of
your tool (model number, type, serial number, etc.).

A complete line of accessories is available from your Porter-Cable

•

Delta

Supplier, Porter-Cable

•

Delta Factory Service Centers, and Porter-Cable

Authorized Service Stations. Please visit our Web Site

www.porter-cable.com

for a catalog or for the name of your nearest supplier.

Since accessories other than those offered by Porter-
Cable

•

Delta have not been tested with this product, use of

such accessories could be hazardous. For safest operation,
only Porter-Cable

•

Delta recommended accessories should

be used with this product.

SERVICE

ACCESSORIES

The following are trademarks of PORTER-CABLE

•

DELTA (Las siguientes son marcas registradas de PORTER-CABLE

•

DELTA S.A.) (Les

marques suivantes sont des marques de fabriquant de la PORTER-CABLE

•

DELTA): Auto-Set

, BAMMER

, B.O.S.S.

, Builder’s Saw

Contractor’s Saw

, Contractor’s Saw II™, Delta

, DELTACRAFT

, DELTAGRAM™, Delta Series 2000™, DURATRONIC™, Emc²™, FLEX

, Flying

Chips™, FRAME SAW

, Grip Vac™, Homecraft

, INNOVATION THAT WORKS

, Jet-Lock

, JETSTREAM

, ‘kickstand

, LASERLOC

, MICRO-

SET

, Micro-Set

, MIDI LATHE

, MORTEN™, NETWORK™, OMNIJIG

, POCKET CUTTER

, PORTA-BAND

, PORTA-PLANE

, PORTER-

CABLE

&(design), PORTER-CABLE

PROFESSIONAL POWER TOOLS, PORTER-CABLE REDEFINING PERFORMANCE™, Posi-Matic

, Q-

&(design), QUICKSAND

&(design), QUICKSET™, QUICKSET II

, QUICKSET PLUS™, RIPTIDE™&(design), SAFE GUARD II

, SAFE-LOC

Sanding Center

, SANDTRAP

&(design), SAW BOSS

, Sawbuck™, Sidekick

, SPEED-BLOC

, SPEEDMATIC

, SPEEDTRONIC

, STAIR EASE

The American Woodshop

&(design), The Lumber Company

&(design), THE PROFESSIONAL EDGE

, THE PROFESSIONAL SELECT

, THIN-

LINE™, TIGER

, TIGER CUB

, TIGER SAW

, TORQBUSTER

, TORQ-BUSTER

, TRU-MATCH™, TWIN-LITE

, UNIGUARD

, Unifence

UNIFEEDER™, Unihead

, Uniplane™, Unirip

, Unisaw

, Univise

, Versa-Feeder

, VERSA-PLANE

, WHISPER SERIES

WOODWORKER’S CHOICE™.
Trademarks noted with ™ and ® are registered in the United States Patent and Trademark Office and may also be registered in other countries.
Las Marcas Registradas con el signo de ™ y ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y también pueden
estar registradas en otros países. Marques déposées, indiquées par la lettre ™ et ®, sont déposées au Bureau des brevets d’invention et
marques déposées aux Etats-Unis et pourraient être déposées aux autres pays.

PORTER-CABLE • DELTA SERVICE CENTERS

(CENTROS DE SERVICIO DE PORTER-CABLE • DELTA)

(CENTRE DE SERVICE PORTER-CABLE • DELTA)

Parts and Repair Service for Porter-Cable • Delta Power Tools are Available at These Locations

(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable • Delta)

(Locations où vous trouverez les pièces de rechange nécessaires ainsi qu’un service d’entretien)

Authorized Service Stations are located in many large cities. Telephone

800-487-8665

731-541-6042

for assistance locating one. Parts and

accessories for Porter-Cable

•

Delta products should be obtained by contacting any Porter-Cable

•

Delta Distributor, Authorized Service

Center, or Porter-Cable

•

Delta Factory Service Center. If you do not have access to any of these, call

888-848-5175

and you will be directed to

the nearest Porter-Cable

•

Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en muchas grandes ciudades.

Llame al

800-487-8665

ó al

731-541-6042

para obtener asistencia a fin de localizar una. Las piezas y los accesorios para los productos Porter-

Cable

•

Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable

•

Delta, Centro de Servicio Autorizado o Centro

de Servicio de Fábrica Porter-Cable

•

Delta. Si no tiene acceso a ninguna de estas opciones, llame al

888-848-5175

y le dirigirán al Centro de

Servicio de Fábrica Porter-Cable

•

Delta más cercano. Des centres de service agréés sont situés dans beaucoup de grandes villes. Appelez au

800-487-8665

ou au

731-541-6042

pour obtenir de l’aide pour en repérer un. Pour obtenir des pièces et accessoires pour les produits Porter-

Cable

•

Delta, s’adresser à tout distributeur Porter-Cable

•

Delta, centre de service agréé ou centre de service d’usine Porter-Cable

•

Delta. Si

vous n’avez accès à aucun de ces centres, appeler le

888-848-5175

et on vous dirigera vers le centre de service d’usine Porter-Cable

•

Delta le

plus proche.

PC7.2-0105-164

CANADIAN PORTER-CABLE

•

DELTA SERVICE CENTERS

ALBERTA

Bay 6, 2520-23rd St. N.E.
Calgary, Alberta
T2E 8L2
Phone: (403) 735-6166
Fax: (403) 735-6144

BRITISH COLUMBIA

8520 Baxter Place
Burnaby, B.C.
V5A 4T8
Phone: (604) 420-0102
Fax: (604) 420-3522

MANITOBA

1699 Dublin Avenue
Winnipeg, Manitoba
R3H 0H2
Phone: (204) 633-9259
Fax: (204) 632-1976

ONTARIO

505 Southgate Drive
Guelph, Ontario
N1H 6M7
Phone: (519) 767-4132
Fax: (519) 767-4131

QUÉBEC

1515 Ave.
St-Jean Baptiste, Suite 160
Québec, P.Q.
G2E 5E2
Phone: (418) 877-7112
Fax: (418) 877-7123

1447, Begin
St-Laurent, (Mtl), P.Q.
H4R 1V8
Phone: (514) 336-8772
Fax: (514) 336-3505

ARIZONA

Phoenix 85013-2906
4501 N. 7th Ave.
Phone: (602) 279-6414
Fax: (602) 279-5470

CALIFORNIA

Ontario 91761 (Los Angeles)
3949A East Guasti Road
Phone: (909) 390-5555
Fax: (909) 390-5554

San Diego 92111
7290 Clairemont Mesa Blvd.
Phone: (858) 279-2011
Fax: (858) 279-0362

San Leandro 94577 (Oakland)
3039 Teagarden Street
Phone: (510) 357-9762
Fax: (510) 357-7939

COLORADO

Denver 80223
700 West Mississippi Ave.
Phone: (303) 922-8325
Fax: (303) 922-0245

FLORIDA

Davie 33314 (Miami)
4343 South State Rd. 7 (441)
Unit #107
Phone: (954) 321-6635
Fax: (954) 321-6638

Tampa 33634
4909 West Waters Ave.
Phone: (813) 884-0434
Fax: (813) 888-5997

GEORGIA

Forest Park 30297 (Atlanta)
5442 Frontage Road,
Suite 112
Phone: (404) 608-0006
Fax: (404) 608-1123

ILLINOIS

Addison 60101 (Chicago)
400 South Rohlwing Rd.
Phone: (630) 424-8805
Fax: (630) 424-8895

Woodridge 60517 (Chicago)
2033 West 75th Street
Phone: (630) 910-9200
Fax: (630) 910-0360

KANSAS

Overland Park 66214
9201 Quivira Road
Phone: (913) 495-4330
Fax: (913) 495-4378

MARYLAND

Elkridge 21075 (Baltimore)
7397-102 Washington Blvd.
Phone: (410) 799-9394
Fax: (410) 799-9398

MASSACHUSETTS

Franklin 02038 (Boston)
Franklin Industrial Park
101E Constitution Blvd.
Phone: (508) 520-8802
Fax: (508) 528-8089

MICHIGAN

Madison Heights 48071 (Detroit)
30475 Stephenson Highway
Phone: (248) 597-5000
Fax: (248) 597-5004

MINNESOTA

Eden Prairie 55344
9709 Valley View Road
Phone: (952) 884-9191
Fax: (952) 884-3750

MISSOURI

St. Louis 63146
11477 Page Service Drive
Phone: (314) 997-9100
Fax: (314) 997-9183

NEW YORK

Flushing 11365-1595 (N.Y.C.)
175-25 Horace Harding Expwy.
Phone: (718) 225-2040
Fax: (718) 423-9619

NORTH CAROLINA

Charlotte 28270
9129 Monroe Road, Suite 115
Phone: (704) 841-1176
Fax: (704) 708-4625

OHIO

Columbus 43229
1948 Schrock Road
Phone: (614) 895-3112
Fax: (614) 895-3187

Cleveland 44125
8001 Sweet Valley Drive Unit #19
Phone: (216) 447-9030
Fax: (216) 447-3097

OREGON

Portland 97230
14811 North East Airport Way
Phone: (503) 255-6556
Fax: (503) 255-6543

PENNSYLVANIA

Willow Grove 19090 (Philadelphia)
520 North York Road
Phone: (215) 658-1430
Fax: (215) 658-1433

TEXAS

Carrollton 75006 (Dallas)
1300 Interstate 35 N, Suite 112
Phone: (972) 446-2996
Fax: (972) 446-8157

Houston 77022-2122
536 East Tidwell Rd.
Phone: (713) 692-7111
Fax: (713) 692-1107

WASHINGTON

Auburn 98001(Seattle)
3320 West Valley HWY, North
Building D, Suite 111
Phone: (253) 333-8353
Fax: (253) 333-9613