Full Text Searchable PDF User Manual
A42
Quick Start Guide
Outdoor mount
This access point can be configured as an outdoor model and
mounted to any wall or pole. This configuration protects against
the sun, rain and dust.
Remove the rear door and outdoor seal from the bottom of
the access point. Attach the universal mounting plate to any
outdoor wall or pole using screws or zip ties (not included). The
small tabs should be at the top of the plate so the cable exits
through the bottom of the access point.
Open the slit in the side of the rubber gasket and place the Eth-
ernet cable through the hole. Plug the cable into Ethernet 1 for
802.3af PoE or Ethernet 2 for 12-24v passive PoE. Ensure the
second hole still has its rubber plug in place. Place the rubber
gasket into the channel surrounding the ports on the access
point. Place the rear cover on the access point and snap into
place. Finally, place the access point over the mounting plate
and slide down until it locks into place.
To unlock, insert a small, flat screwdriver into the hole on the
side of the access point. Slide the access point until it disen-
gages from the mounting plate.
Ò
openmesh.com/a-outdoor
Ethernet or junction box mount
This access point can be mounted to any US or European-style
junction box for secure installations in hotel and resort guest
rooms, dorms, care facilities and more.
Remove the rear door and outdoor seal from the bottom of
the access point. Attach the universal mounting plate with the
smooth side against the wall to a junction box using the desig-
nated screw holes. Connect the small Ethernet cable (included)
to the female connection in the wall, then pull it through the
mounting plate and plug into Ethernet 1 for 802.3af PoE or
Ethernet 2 for 12-24v passive PoE. Connect any pass-through
device to the unused Ethernet port and position the cable in
the bottom channel of the access point. Next, place the access
point over the mounting plate and slide down until it locks into
place.
To unlock, insert a small, flat screwdriver into the hole on the
side of the access point. Slide the access point until it disen-
gages from the mounting plate.
Ò
openmesh.com/a-ethernet
1.
2.
We help professionals create powerful, easy-to-use networks that automatically spread Internet
connections throughout hotels, apartments, retail stores, restaurants, small and medium-sized
businesses—and just about anywhere else.
The Open Mesh A Series access points are a modular, plug-and-play professional WiFi solution
that works with CloudTrax, a free cloud-based network controller that can manage
an unlimited number of switches, access points and networks around the world.
openmesh.com
© 2017 Open Mesh, Inc. All Rights Reserved.
111 SW 5th Ave, Suite 1150, Portland, OR USA 97204
The software included in this product contains copyrighted software that is licensed under GPL. A copy of that
license, along with instructions on how to obtain the source code, is available at http://www.openmesh.com/gpl.
Access point overview
LED indicator
Ethernet port 1, 802.3af PoE
Reset Button
Cable Channel
USB 2.0
Ethernet port 2, 12-24v passive PoE
Cloud management
1. Download the CloudTrax mobile app for iOS or Android,
or sign up at
cloudtrax.com. (It’s included with this access
point.)
2. Follow the prompts to verify your account and create your
first network. If you already have a network, create a new
one by navigating to
Network → Create new network.
3. Follow the prompts to add your first access point. If you’re
adding this access point to an existing network:
In the CloudTrax mobile app: select
Add Access Point from
the top menu and scan the QR code on the bottom of the
access point.
On cloudtrax.com: navigate to
Manage → Access Points →
Add New and enter the MAC address. Use the drop-down
arrow to enter multiple MAC addresses at once or upload a
CSV file.
Repeat this process to add as many access points as
required.
4. Set your configuration. Once your access point has power
and Internet, CloudTrax will configure the access point and
start reporting status within a few minutes.
Mounting bracket overview
T-rail ceiling mount
Remove the rear door and outdoor seal from the bottom of the
access point. Attach the fixed t-rail clips to the back of the uni-
versal mounting plate by pushing the top of the clip through the
plate and securing the bottom of the clip to the mounting peg:
use the narrow peg hole for ⁹/₁₆" t-rails and the wider peg hole
for 15/₁₆" t-rails. Attach the adjustable clips to the mounting plate
by pushing the top of the clip through the plate and snapping
the bottom of the clip into the channel. Pull the Ethernet cable
through the center of the mounting plate and plug into Ethernet
1 for 802.3af PoE or Ethernet 2 for 12-24v passive PoE. Next,
place the access point over the mounting plate and slide until it
locks into place. Clip the cable channel cover in place. Finally,
attach the access point to the ceiling rail by placing the fixed
clip against the rail and sliding the adjustable clips until secure.
Ò
openmesh.com/a-ceiling
¹⁵/16" rails ⁹/16" rails
Continued on reverse side
Physical installation
This access point is designed to be installed virtually anywhere,
indoors and out. Regardless of how you mount this access
point, keep the following in mind:
● This access point can use 802.3af or 12-24v passive PoE
input. Connect to an 802.3af-compatible PoE switch or PoE
injector in Ethernet 1, or 12-24v passive PoE in Ethernet 2.
● Place the access point in the center of the room and away
from any metallic surfaces.
● This access point radiates signal primarily to the front and
sides. This access point will only provide limited coverage
directly behind it.
● Do not place heavy objects on the access point.
● Install the access point in an area free from strong
electromagnetic sources.
● Check the Ethernet cables to ensure they are fully secured
to both the access point and PoE injector or switch.
● Do not install this access point in plenum spaces. Use the
ceiling mount instead.
Support and resources
Visit
help.cloudtrax.com for additional resources, video guides
and to contact technical support.
US single
gang box
US dual
gang box
EU/UK
Wall or solid ceiling mount
Remove the rear door and outdoor seal from the bottom of
the access point. Attach the universal mounting plate to any
solid surface with the smooth side against the wall (screws are
not included). If the Ethernet cable is in the wall or ceiling, pull
it through the mounting plate; if the cable is outside the wall
or ceiling, place it in the cable channel. Plug the cable into
Ethernet 1 for 802.3af PoE or Ethernet 2 for 12-24v passive PoE.
Next, place the access point over the mounting plate and slide
down until it locks into place.
To unlock, insert a small, flat screwdriver into the hole on the
side of the access point. Slide the access point until it disen-
gages from the mounting plate.
Ò
openmesh.com/a-wall
LED State
Indication
Solid Purple
or Yellow
AP is booting
Solid Red
Firmware upgrade in
progress
Flashing Red
or Purple
Offline: no default route or
DNS down
Solid Teal
Online in gateway mode
Flashing
Green
Online in repeater mode,
mesh speed <=2Mbps
Solid Green
Online in repeater mode,
mesh speed >2Mbps
Solid White
Settings change in progress
Visit
help.cloudtrax.com for a complete list
of LED indications.