PDF User Manual

  1. Home
  2. Manuals
  3. Noztek Pro User Manual

Noztek Pro User Manual

Made by: Noztek
Type: User Manual
Category: Sander
Pages: 5
Size: 0.23 MB

 

Download PDF User Manual



Full Text Searchable PDF User Manual



background image

 

  

     PRO USER MANUAL 
 

 

 
 

 
 
 

1.  Safety 
2.  Introduction 
3.  Specifications 
4.  Extrusion operation 
5.  Colour mixing 
6.  Changing the nozzle 
7.  Maintenance 
8.  Troubleshooting 

 
 
 
 

 


background image

 

WARRANTY NOTE 

Equipment manufactured by Noztek carries the standard machine tool guarantee 
of freedom from defects in workmanship and material for one year from date of 
shipment. 
TO INSURE THAT YOUR WARRANTY IS HELD IN EFFECT, PROPER 
OPERATION PROCEDURES MUST BE OBSERVED. 
NOTE: READ THE SAFETY PRECAUTIONS BEFORE OPERATING THIS 
MACHINE. 
 
 
 
 
 
 
 

GENERAL SAFETY NOTES 

Know your equipment 
Carefully read the instruction manual. 
Learn the use and limitations of the equipment. 
 
 
 
DO NOT operate or use this equipment for any purpose other than its intended 
use. 
DO NOT modify this equipment. 
DO NOT perform adjustments or maintenance while system is operating or 
energize 
 
Do not clean the equipment with flammable solvents. 
Do not wash down the equipment with water. This could cause an electrical 
hazard. 
Do not probe into extruder vent with the machine running. Never Use a metal 
probe in the vent area. The screw may shear the probe, causing extensive 
damage to the barrel and screw. A wooden probe is recommended. 
A face shield, insulated gloves, etc. should be worn around the extruder during 
operation. They must be worn when adjusting the die, cleaning the screw, etc. 
The extruder temperatures are extremely hot. 
The feed hopper must be installed on the extruder feed section at all times when 
in operation 
Never put hands in the feed section or vent to remove material. 
Do not switch on the motor until the recommended temperature has been 
reached 
 

 


background image

 

 

 
 
Introduction 
 

The Noztek desktop extruder has been designed to produce high quality ABS 
and PLA filament for use with 3D printers. For best results we recommend using 
extrusion grade polymer pellets. 
 

Maintenance 

Your Noztek Pro comes complete with an emergency stop button. If you are 
using the 45 degree bracket it is very important that the extruder is secured to a 
workbench using the mounting holes in the bottom of the bracket. 

 


background image

 

In an emergency simply hit the button and the Noztek Pro will completely switch 
off. To restart, simply untwist the button. 

 
Extrusion operation 

 

  Remove the unit from the packaging 

  If you are using the 45 degree bracket, secure the extruder to a bench 

using the mounting holes. 

  Make sure you are in a well ventilated area 

  Plug the extruder into the mains. 

  Switch on the heater element and adjust the temperature gauge to the 

desired setting. For ABS we recommend between 180 – 200 degrees 
Celsius and PLA between 165 -175c. To adjust the heat setting press the 
set key once, the temperature led will then flash, then the click up or down 
key to adjust. When you reach the desire temperature click the set button 
to engage. Let the extruder barrel heat fully this should take about 15 
minutes. 

  Once the required temperature has been reached, fill the hopper with 

resin pellets. 

  Switch on the screw motor (Do not switch on the motor until the 

recommended temperature has been reached). 

  Switch on the fan  

  After a few minutes you will see plastic filament starting to extrude, 

carefully feed this through the guide, This filament will be hot so use heat 
resistant gloves 

  Extrude approximately 5m of filament, switch off the motor, cut off the 

excess material, and then restart the motor. This should help to eliminate 
any air bubbles and metal particles in the system. 

  Adjusting the temperature also affects the tolerance of the filament. The 

higher the temperature, the thinner the filament. The lower the 
temperature, the thicker the filament.  

  Make these adjustments in 5 degree Celsius increments. 

  If the extruder is left unattended for any period of time we recommend 

using a mains timer switch. 

 

 
 
Changing the nozzle 

 
Before attempting this operation please use insulated gloves. 
To switch between nozzle sizes to heat up the unit to175c, unscrew the nozzle, 
clean off any excess plastic from the internal threads, and then screw on new 
nozzle. 
 

 
 

 


background image

 

Colour Mixing 
 

Adding colours is simple. Mix the natural and the colorant at the given ratio. Then 
pour it into the hopper. It will take 10-20 minutes to see changes in the colour. It 
is also possible to mix colorant to get new colours. For example, blue and yellow 
make green.  

 

 
 
 
 
Maintenance 

 
Regular cleaning of your plastic extrusion tooling during the disassembly 
process lengthens tooling life, helps reduce scrap and helps maintain 
tighter tolerances on your final product. Use a wire brush and fine metal pick to 
clean the threads and the screw assembly. 
 
 
Note: Common practice is to use a propane torch to burn out excess material 
from the tip. 
CAUTION: Do not heat excessively or cause material to be red hot. 

 

 

Noztek UK   

info@noktek.com

  

www.noztek.com

 

 
Unit D05, Riverside Business Centre, Haldane Place, Wandsworth., London 
SW18 4UQ 
 
44 203 394 6208