Full Text Searchable PDF User Manual
Technical data
NLCUT1
Supply voltage:
230V 50/60Hz
Consumption:
ca. 1W
Contact rating:
changeover contact 16A 250V~μ cos
ϕ
= 1
Parallel compensation:
not allowed
Accuracy: ±2,5s/d
Terminal capacity:
single strand multi strand
1,5 to 4 mm
2
1,5 to 2,5 mm
2
Program pictures:
8
Battery reserve:
100h
Storage ambient:
-10°C to +60°C
Working ambient:
-10°C to +55°C
1000W 1000W 2500W 1000W
2000W 1000W
For saftety, when the time switch is connected to the mains supply the contact should not be
used on an isolated low voltage supply. And when the time switch is connected to the isolated
voltage supply the contact should not be used on the mains supply.
Connection
1 2
5
4
3
L
N
State of output
= On
= Off
±
1h C
S OK
R
Hand switch
Choose function
Summer- / winter
changeover
Setting the hours, minutes
and days
Delete
Fixing the hours, minutes,
days and continuous
switching
Programming Buttons
12345
67
Actual or „On“ time
Weekday
Day number
„Off“ time
Symbol for
„Set actual time“
„Off“ days
Liquid Crystal Display
S
OK
+
Safty notes
This product may be installed only by a qualified electrician. Non-compliance may result in a fire hazard or electric shocks. Before installation, read
the operating instructions and observe the product-specific requirements for the installation location. Use only original spare parts for repair and
maintenance. Unauthorised opening and repair by other persons will invalidate all claims for liability, replacement or warranty services.
Function
The
NLCUT1
is a microprocessor controlled digital time switch. Eight programs of your choice can be stored and used to control the automatic operation of your electrical equipment.
Each individual weekday can have a separate program or you can have several days operating on the same „Block“ program. To program the
NLCUT1
a „picture“ is used and when this is complete
the chosen times are stored in the microprocessor memory. The summer-/winter changeover can be programmed for hand or automatic operation.
Presentation
Approximately 30 seconds after the supply voltage is connected the symbols
appear on the LCD.
Before any operations the complete memory must be reset.
2. Memory reset
1. Starting
This can only be done after a Reset.
Summer- / winter changeover can be made manually or automatically if set.
If manual changeover is required choose
no
during the date input. Automatic
changeover depends on your country / area. Choose the appropriate setting
for your country / area.
3. Setting date and summer- / winter changeover
press both at
the same time
The time switch memory is completely clear.
NLCUT1
N292338/00
±
1h
The time switch will follow the next „On“ or
„Off“ program
Display
= On
Display
= Off
Otherwise use
to set another day
Press until
display is as shown
12. Correcting mistakes
(only in the mode of programmation)
Hold & Press
both buttons
together
Display
Display
The time switch will remain in continuous
„On“ or „Off“ position until it is changed.
Press once
The time switch returns immediately to pro-
gram mode
9.1 Terminating continuous switching
S
S
S
S
OK
OK
OK
12345
67
12345
67
12345
67
12345
67
S
S
S
OK
OK
OK
Press to change to off hour
S
S
OK
OK
S
S
OK
OK
Press once
Press once
Set off hour
Set off minute
S
OK
Press once
12345
67
12345
67
12345
67
12345
67
12345
67
Press several
times until correct
„picture“ is shown
C
Press until the
actual time is shown
Set other days
as required
Press once
If the clock is on the correct day press
S
OK
OK
OK
This function only applies to channel 1
The switch condition
must
first be chosen
Press to give desired function
Display
= On
Display
= Off
S
Press
C
Press once
END
Press until actual
time is displayed
11. Summer-/ Winter changeover
This function is only available if
no
was
chosen during date input for
summer- / winter selection (see 3)
OK
Press once
END
In the above example the time switch
stays „On“ for 14 days. At 0:00 hours on
the 15th day the time switch returns to its
program mode.
S
Press to choose the
number of days
(d1 to d99)
S
OK
OK
12345
67
12345
67
12345
67
End of program
Press once
5.3 Single day programs
Press until this
display appears
Press once
Press once
Set On hour
Set On minute
Press until this
display appears
Set times as 5.1 above
The switch condition
must
first be chosen
Display
= On
or
= Off
Press as required
END
only if it is
necessary
Press once
10. Continuous switching for a
chosen number of days
Press until the actual time goes forward
1 hour (summer) or back 1 hour (winter)
10.1 Terminating continuous
switching
Set On day
Set On Minute
Press until the
correct year is set
Press once
Press once
Press once
Choose
(See table below)
Setting of the beginning of summer
code 1
End date setting code
code 0
Set the end date
as above
Press until the
correct day is set
Press until the
correct month is set
Each program has an On- and Off-time.
5.1 7 Day block program. Each day the same
Set the Off hour
Press until this
display appears
Press once
Press once
Press once
Set the On hour
Set the On minutes
S
S
S
OK
OK
OK
Set the year
Press once
Press once
Press once
The start date is set.
Set the day
Set the month
Set the Off minutes
End of program
Press once
6. Check switching times
Press several times until
correct „picture“ is shown
Press until the
actual time is shown
7. Delete switching times
9. Continuous switching
Press once to either
C
END
13. Checking the date setting
S
S
OK
OK
12345
67
12345
67
Press once
Press once
Press once
Actual time is now set
Press until the correct
hour is shown
Press until the correct minute is shown
The weekday will shown
automatically.
Choice
no
press once
4. Setting actual time
Choice
Summer
begins
Summer
ends
Country /
area
E
A
Gb
no
H
1
ST
Sunday
in April
4th Sunday
in October
last Sunday
in October
last Sunday
in October
last Sunday
in April
last Sunday
in march
only
North
America
GB
EU
No
changeover
No
changeover
Enter here the date for the beginning of
summer for your country / area as well as
the end of summertime. E.g. 31
ST
March is
shown for the beginning of Summertime. In
the following years it starts on the same day
irrespective of the date.
12345
67
After setting the summer start
now set the actual time
Press as required
8. On and Off manual operation
Code d
+
This function is not available if
no
was
chosen during date input for
summer- / winter selection (see 3)
S
S
Press to delete program
and set a new programm
or-
OK
5.2 Day Monday to Friday program
5. Setting switching time
+