Full Text Searchable PDF User Manual
Conforms to
ASTM F1169-10a
Full-Size Crib Standard
GUARDRAIL and CONVERSION KIT sold separately
Please contact retailer.
SUSSEX
MODEL # 6299
ASSEMBLY INSTRUCTIONS
for 4 in 1 Life time Crib
®
THIS PRODUCT CONFORMS TO THE APPLICABLE SECTIONS OF PUBLIC LAW 110-314 AND COMPLIES WITH
THE REQUIREMENTS STATED IN 16 CFR 1219 AND 16 CFR 1217 (WHEN SUSSEX GUARDRAIL IS USED).
02-A-SUCM01-00
(M) Barrel Nut 1
(4 pcs)
”
(25 mm)
( F ) Allenbolt 2 3/4 (70 mm) (8 pcs)
”
( H ) Allenbolt 2
”
(50 mm) (2 pcs)
( J ) Allenbolt 1 1/4 (30 mm)
(4 pcs)
”
( L ) Nut 3/4
(8 pcs)
”
(20 mm)
( W ) Spring Washer (16 pcs)
Make sure the bolts are tightly locked against the washers during assembly.
(Please add an extra ½ revolution to all the bolts when using spring washer after tightening)
(N) Allenkey (2 pcs)
( length may vary)
( O ) Allenbolt 1 1/2
”
(40 mm)
(2 pcs)
02-A-SUCM01-00
FACE / AVANT
INSIDE / INTÉRIEUR
STEP 1.1
- Insert nut 3/4” (20 mm) (L) through the top and bottom holes in
side board from the outside.
- Insert allenbolt 2 3/4"
(F) & spring washer (W)
through the top and bottom holes in headboard
and connect to the headboard. Hand tighten only!
- Repeat STEP 1.1 for other side board
(70 mm)
(70 mm)
STEP 1.2
- Insert barrel nut 1” (25mm) (M) into holes in stabilizer bar
- Connect stabilizer bar to the side board using (4 pcs) allenbolt 2 3/4”
(F)
& spring washer (W)
- Tighten all bolts with allenkey (N)
STEP 1.1
(N)
(L)
(F)
(N)
(F)
(W)
(W)
M. Barrel Nut 1” (25 mm) (4 pcs)
F. Allenbolt 2 3/4 (70 mm) (8 pcs)
”
N
L. Nut 3/4 (20 mm) (4 pcs)
”
W. Spring Washer (8 pcs)
RIGHT / DROIT
INSIDE / INTÉRIEUR
(M)
STEP 1.2
02-A-SUCM01-00
L. Nut 3/4 (20 mm) (4 pcs)
”
- Attach mattress spring (E) to Side board as shown in FIG.3.
- Secure with allenkey (N).
- See FIG. 4 for height adjustment
- Make sure the mattress spring is leveled after assembly.
2
W. Spring Washer (4 pcs)
N. Allenkey (2 pcs)
FIG. 4
Highest
Position
Middle
Position
Lowest
Position
(J)
(N)
(W)
FIG. 3
(W)
(J)
(N)
(L)
J. Allenbolt 1 1/4 (30 mm) (4 pcs)
”
02-A-SUCM01-00
- Insert allenbolt 1 ½" (40 mm) (O) & spring washer (W) through the top holes in side board
into the threaded holes footboard (B). FIG. 5
FIG. 6
- Insert allenbolt 2"
(H) & spring washer (W) through the bottom holes in side board
into the threaded holes footboard (B).
- Tighten all bolts and nuts with allenkey (N)
(50 mm)
N
3
H. Allenbolt 2” (50 mm) (2 pcs)
W. Spring Washer (4 pcs)
(N)
(H)
(W)
(O)
(W)
(B)
O. Allenbolt 1 1/2
”
(40 mm) (2 pcs)
02-A-SUCM01-00
FIG. 5
FIG. 6
Inline
and have
no gap
"
-
-
-
GUARDRAIL and CONVERSION KIT sold separately.
Please contact retailer.
SUSSEX
MODEL # 6299
02-A-SUTM01-00
-Remove the footboard by unscrewing the (4 pcs) allenbolts as shown in FIG.1.
02-A-SUTM01-00
- Remove the allenbolt 1 1/4” (30 mm) (J), spring washer (W) and nut 3/4” (20 mm) (L) on the mattress spring.
- Move Mattress spring to the lowest position as shown in FIG.2.
- Attach the
(J)
and nut
(L) on the lowest hole of side frame.
- Final position as shown in FIG.3.
allenbolt 1 1/4” (30 mm)
, spring washer (W)
3/4” (20 mm)
L. Nut 3/4” (20 mm) ( 4 pcs )
(N)
(2 pcs)
W. Spring Washer (4 pcs)
these hardware are included in the CRIB
Lowest
Position
(J)
(W)
(N)
(L)
J. Allenbolt 1 1/4 (30 mm) (4 pcs)
”
02-A-SUTM01-00
