PDF User Manual

  1. Home
  2. Manuals
  3. Luxline Portable 8 Operation Manual

Luxline Portable 8 Operation Manual

Made by: Luxline
Type: Operation Guide
Category: Water Heater
Pages: 16
Size: 0.24 MB

 

Download PDF User Manual



Full Text Searchable PDF User Manual



background image

 

 

OPERATION GUIDE 

 

 

 
 
 
 
 
 
 

For customer service on this appliance: 
 
Phone: 1300 371 858 
Web: luxline.com.au / luxline.co.nz

 

 

 

GMK10191

 

 
 

 

 


background image

 
Thank you for choosing a Luxline Portable 8 hot water system. This manual contains 
information to help you get years of safe and enjoyable service from your gas hot 
water system. Please take the time to read it in full before operating. 
 
 
 
 
 
 
 
 
 
 
 
 

IMPORTANT! 

 
Read these instructions for use carefully.  Familiarise yourself with the appliance 
before connecting it to its gas container. Keep these instructions for future reference. 

 
 

IMPORTANT! 

 
This appliance is designed to be used with a source water temperature of 20°C or 
below. If the temperature of the outlet water exceeds 50°C the burners will shut off. 
You will need to turn the water flow off and on again to reignite the burners. 

 
 

THIS APPLIANCE IS NOT INTENDED FOR THE SUPPLY OF DRINKING WATER. 
 
THIS APPLIANCE IS INTENDED FOR THE SUPPLY OF HEATED WATER FOR 
THE PURPOSES OF WASHING AND CLEANING ONLY. 
 
CHECK AND CONFIRM SAFE WATER TEMPERATURE BEFORE USING THIS 
APPLIANCE. WATER FROM THIS APPLIANCE MAY BE VERY HOT. 
 
THIS APPLIANCE MUST BE PROTECTED FROM RAIN. 

 

 

 


background image

GENERAL   WARNINGS   

 

This appliance shall only be used with a propane gas refillable container 
certified to AS2469. It may be hazardous to attempt to fit other types of gas 
containers. 
 
This appliance shall only be used with a propane gas refillable container 
certified to AS2469. It may be hazardous to attempt to fit other types of gas 
containers. 
 
This appliance shall only be used with the approved 1200mm propane gas 
hose and regulator assembly that have been supplied. 
 
This appliance is to be stored in a dry and well-ventilated location away from 
direct sunlight. Do not store when still connected to the cylinder. 
 
Make sure that the cylinder is disconnected and is stored in a well-ventilated 
area, out of reach of children, and free from direct sunlight, heat and ignition 
sources. If being stored indoors, ensure that the location complies with 
AS/NZS1596. 
 
This appliance must only be serviced by an authorised person. It must be 
returned to its place of purchase for services and repairs. 

DANGER!   

 

 

Use outdoors only. 

 

Only use in well ventilated areas. 

 

Caution: Accessible parts may be very hot. Keep young children away. 

 

Do not use this appliance if it is leaking, damaged, or not operating properly. 

 

Do not use this appliance if it has damaged or worn seals. 

 

This appliance shall only be used in an above ground open-air situation with 
natural ventilation, without stagnant areas, where gas leakage and products of 
combustion are rapidly dispersed by wind and natural convection. 

 

Only use the hose assembly as supplied with this appliance for connection to 
the cylinder.  DO NOT USE ADAPTORS. 

 

Children must be supervised by an adult at all times when using this 
appliance. 

 

Never leave appliance unattended when operating. 

 

Do not use as a cooking appliance or modify for any other reason. 

CARBON   MONOXIDE   HAZARD   

USING THIS APPLIANCE IN AN ENCLOSED SPACE MAY CAUSE DEATH.  DO 
NOT USE IN CARAVANS, TENTS, MARINE CRAFT, CARS, MOBILE HOMES, OR 
SIMILAR LOCATIONS. 

 


background image

IMPORTANT   

 

Avoid twisting or kinking the flexible gas hose. 

 

If there is a leak in your appliance (smell of gas), immediately attempt to 
turn off the cylinder valve.  Remove the appliance to a well-ventilated 
location away from any ignition source. Check for leaks using soapy 
water. Do not try to detect leaks using a flame. 

 

Do not attempt to move or relocate the appliance when it is operating. 
Extinguish the burner and allow it to cool. Disconnect the gas cylinder 
then move the appliance using the handle. 

CHECKING   FOR   GAS   LEAKS   

 

Check that seals between the appliance and the gas container are in place 
and in good condition before connecting the gas container. 

 

If the O-ring on the POL fitting of the gas hose is missing, 
worn, or damaged, you must obtain a replacement from 
an authorised service centre. 

 

NEVER

 check for leaks with a flame or pilot light. 

 

To safely check for leaks, use the ‘soapy water’ method. 
Coat the connection points (i.e. the connection between 
the hose and the hot water system, and the connection between the hose and 
the gas bottle) with a thin layer of soapy water. If you see bubbles appear, turn 
the cylinder gas control off and retighten the connection before re-testing. 

 

Inspect the appliance regularly for signs of wear, leaks or 
incorrect operation. If symptoms such as burner flares, 
lighting issues, hose or connection damage, or leaks from 
the seals or gas controls are identified, do not attempt to 
repair; contact customer service. 

 

There is a plastic ring seal inside the gas hose adaptor. If 
the seal is missing, worn, or damaged, you must obtain a 
replacement from an authorised service centre. 

 

To check if gas remains in the cylinder, disconnect from the appliance and 
hold the cylinder in a vertical position then shake from side to side.  If there is 
a sound or feel of liquid movement inside the cylinder contains gas. 

 

Change the gas cylinder outside in a well-ventilated location away from 
people, animals, and ignition sources such as naked flames, pilot lights, and 
electrical equipment such as heaters.  

 

 

 


background image

HANGING   THE   APPLIANCE   

OUTDOOR USE ONLY – The appliance must be used outdoors only. Combustible 
surfaces, fabrics, and flammable materials must be kept at least 1000mm away from 
the sides and top of the appliance while it is operating.  
 
The appliance is designed to be hung upright against a non-combustible vertical 
surface. Do not operate from a non-upright position. Doing so can be dangerous and 
will damage the appliance. 
 
Do not operate the appliance in a dusty environment, or within 300mm of any 
electrical appliances or electrical wires. 
 
During operation, ensure that the combustion air inlets on the sides of the unit and 
the combustion air exhaust on the top of the unit are kept free from obstructions. 

APPLIANCE   PERFORMANCE   

Important – this appliance is designed to be used with a source water temperature of 
20°C or below. If the temperature of the outlet water exceeds 50°C the burners will 
shut off; you will be required to turn the water flow off and on again to reignite the 
burners. 
 
This appliance is designed to raise the outlet water temperature by a maximum 
(average) of 25°C above the source water temperature. The temperature increase 
can be adjusted using the gas regulator and water regulator control knobs located at 
the front of the device. Increasing the gas flow, or decreasing the water flow, will 
increase the outlet water temperature.  
 

SAFETY   FEATURES   

The appliance is equipped with the following safety features: 
 

Over temperature sensor.

 The appliance will not allow the burner to remain in 

operation once the outlet water temperature reaches 50°C. To relight the burner you 
will need to turn the water flow off and back on. 
 

Water flow sensor.

 Water must be flowing through the system to allow the burner to 

ignite. If the water supply is restricted (for example: if you shut off the water flow at 
the showerhead), the burner will be extinguished and will not relight until the water 
flow recommences. 

 

 

 


background image

SAFETY   INSTRUCTIONS   

This appliance must only be used in an above ground open-air situation with natural 
ventilation, without stagnant areas, where gas leakage is rapidly dispersed by wind 
and natural convection. 
 
The following figures show outdoor areas suitable for use with this appliance. 
Rectangular areas have been used in these figures – the same principles apply to 
any other shaped areas. 
 
Any enclosure in which the appliance is used shall comply with one of the following: 
 

A)

 

An enclosure with walls on all sides, but with no overhead cover, such as: 

 

B)

 

Within a partial enclosure that includes an overhead cover and no more than 
two walls, such as: 

 

 


background image

 

C)

 

Within a partial enclosure that includes an overhead cover and more than two 
walls, the following shall apply: 

a.

 

At least 25% of the total wall area is completely open 

b.

 

30% or more in total of the remaining wall side, back and front wall 
areas is open and unrestricted. 

c.

 

In the case of balconies, 20% or more of the total wall area shall remain 
open and unrestricted. 

For example: 

 

 

 

 


background image

PARTS   INCLUDED   

Description 

Quantity 

Identification 

Remarks 

Portable gas 
water heater

 

1 piece

 

 

 

Shower head with 
shower hose

 

1 set

 

 

 

Gas regulator 
with gas hose

 

1 set

 

 

Test for leaks 

after fitting 

(see page 4) 

Gas adaptor

 

1 piece

 

 

Already fitted at the 
factory 

Water adaptor

 

1 piece

 

 

 

Teflon tape

 

1 roll

 

 

 

Batteries 

2 pieces

 

 

 

Washers 

2 pieces 

 

 

Portable 12V 
water pump

 

1 piece

 

 

Not required for 
operation 

Hanging kit 

1 set

 

 

Not required for 
operation 

 

TOOLS   REQUIRED   FOR   ASSEMBLY   

 

 

Shifting spanner 

 
 

   

 


background image

PREPARING   THE   APPLIANCE   

Before use, it is important to prepare the appliance by installing the proper adaptors 
to suit its intended use. In this example, we will be preparing the portable water 
heater to be used with a garden hose water input. (To use with other water input 
sources such as a water pump, please consult the pump instruction manual or 
contact us for advice). 
 
1) Remove the heater and all components from the box and place them on a table in 
front of you. Remove the Styrofoam. Identify the gas input, hot water output, cold 
water input, and battery box on the underside of the heater. 
 
2) Insert the two ‘D’ batteries into the battery box, with polarities as shown, and close 
the battery box lid. 

 

3) Fit the gas hose with regulator to the gas adapter fitting on the ‘gas input’. Tighten 
the connection with a spanner, taking care not to over-tighten as this could damage 
the nut or the gas inlet adaptor. Test for leaks after fitting (see CHECKING FOR GAS 
LEAKS on page 4). 

 

Wrap the ‘water input’ thread with two rotations of Teflon tape and the install the 
supplied garden hose adaptor. Tighten the adapter connection with a spanner, taking 
care not to over-tighten as this could break or crack the inlet pipe. 

 

4) To attach the showerhead to the supplied flexible shower hose, first place one of 
the supplied washers in the threaded fitting between the shower hose and 
showerhead. Then screw the fitting onto the showerhead. 

 

5) Attach to the included hand showerhead. Note that you can also apply Teflon tape 
to this threaded connection to avoid leaks.  

   

 


background image

10 

OPERATING   THE   APPLIANCE   

Now that the appliance has been prepared with the proper adapter fittings and 
connections for our intended use (with a garden hose water supply) we can set it up 
for operation. 
 

1)

 

Find a suitable sturdy, non-combustible vertical surface to hang the appliance. 
The surface should be at least 1000mm clear from the sides and 1000mm 
from the top of all combustible surfaces, fabrics, flammable materials, and 
people. Hang the appliance on a suitable vertical surface by the handle 
attached to the back cover of the heater. The appliance is ready to be 
connected to gas and water hoses. 

2)

 

Attach the flexible hose and regulator to the ‘gas inlet’. Tighten this connection 
with a spanner, taking care not to over tighten as doing so may damage the 
pipe. 

3)

 

Connect the other end of the flexible hose and gas regulator to the propane 
gas cylinder. Hand-tighten the connection in an anti-clockwise direction. Note: 
never place the gas cylinder directly beside or above the appliance. 

4)

 

Turn the gas cylinder on (open) in an anti-clockwise direction one full turn, and 
then check the connections for leaks with soapy water. DO NOT use a flame. 
If a leak is detected, turn the cylinder valve off (close) and retighten all 
connections and retest. 

5)

 

Once you determine that there are no leaks present with the gas valve open, 
turn the cylinder valve to the off (close) position. 

6)

 

Place the second supplied washer inside the threaded fitting on the loose end 
of the shower hose. Attach this fitting to the ‘water outlet’ connection. If 
necessary, you can use Teflon tape to avoid leaks. 

7)

 

Prepare a garden hose with a ‘quick fitting’ plug and attach it to the male 
garden hose fitting already installed on the ‘water inlet’ pipe. (This appliance is 
also compatible with other forms of water supply including low voltage water 
pumps. For information on how to connect to this please consult your pump 
accessory instruction manual or contact us). 

8)

 

Ensure that the flow regulation switch on the showerhead is in the ‘off’ 
position. 

9)

 

IMPORTANT: It is important that when starting the appliance that the gas 
regulator is set to the minimum position, fully to the left, indicated by the thin 
dotted end of the curved line. 

10)

 

IMPORTANT: It is important that when starting the appliance that the water 
regulator is set to the maximum position, fully to the left, indicated by the thick 
dotted end of the curved line. 

11)

 

 Turn the gas cylinder on in an anticlockwise direction one full turn. 

12)

 

 Open the valve for your water supply. Water should not start to flow out of the 
showerhead as it is still in the ‘off’ position. 

13)

 

 When ready, slide the flow regulation switch on the showerhead to the ‘on’ 
position. Water will start to flow through the showerhead within a few seconds. 
You should hear a series of clicks and then the burner should ignite. The 
burner flame can be seen operating through the viewing window located at the 
front of the appliance. 

 


background image

11 

14)

 

 Adjust the temperature of the water flowing from the showerhead by turning 
the ‘gas’ and ‘water’ knobs. 

a.

 

Turning the gas knob towards the 

 symbol will increase gas flow.  

Turning the gas knob towards the 

 symbol will decrease gas flow. 

b.

 

Turning the water knob towards the 

 symbol will increase water flow. 

Turning the water knob towards the 

 symbol will decrease water 

flow.  

c.

 

For higher temperatures increase the gas flow and decrease the water 
flow.   

d.

 

You can also adjust the temperature of the water flowing from the 
showerhead using the ‘season’ control knob. The ‘Summer’ setting 
turns off some burners to save gas.  The ‘Winter’ setting turns on all 
burners to provide hotter water.  

 

Warning! Take care to test the temperature of the water flowing from the 
showerhead, as it may be hot enough to cause injury.  

 
The water flow can be stopped at any time by sliding the regulation switch on the 
shower head to the ‘off’ position. The burner will extinguish.  
 
To reignite the burner, slide the flow regulation switch to the ‘on’ position. Water will 
commence to flow and the burner will ignite within 5 seconds. 

WATER   CYCLING   INSTRUCTIONS   

To achieve maximum water temperature at higher flow rates you can ‘cycle’ the 
water. To do this, pump the water from a source reservoir (such as a bucket) through 
the heater and back into the reservoir. You can cycle the water as many times as 
required to reach your desired temperature, up to 50°C. 

STORING   THE   APPLIANCE   

1)

 

After use, turn the cylinder gas valve in a clockwise direction to the ‘off’ (close) 
position. The burner will continue to operate until all gas has been bled from 
the hose and regulator assembly. 

2)

 

Wait for the flame to go out, then turn the appliance control valve(s) off. 

3)

 

Turn off the water supply at the garden hose tap. Disconnect the ‘quick fitting’ 
garden hose attachment from the ‘water inlet’. 

4)

 

Disconnect the regulator and hose assembly from the appliance and gas 
cylinder and store away. 

5)

 

Disconnect the showerhead and hose from the ‘water outlet’, hold the shower 
head approximately 1 metre from the ground and allow all water to drain out 
before rolling up and storing away. 

 

   

 


background image

12 

DISCONNECTING   FROM   CYLINDER   

1.

 

Check that the appliance is fully extinguished, the gas cylinder control valve is 
in the fully ‘off’ position and all surfaces are cool. 

2.

 

Loosen the connection to the gas cylinder in a clockwise direction. 

DRAINING   THE   HEATER   WHEN   STORING   BELOW   0

°

C   

When the ambient temperature is below freezing, it is essential to drain the 
water after using the heater.  Failure to do so will void your warranty. 

1.

 

Ensure that the heater is disconnected from the gas supply. 

2.

 

Ensure that the heater is disconnected from the water supply. 

3.

 

Ensure that the shower hose is disconnected from the heater. 

4.

 

Turn the water flow knob to 

5.

 

Operate the drain valve at the base of the appliance until all water has drained 
from the heater.  

CARE   INSTRUCTIONS   

Using warm soapy water with a mild detergent wipe down all surfaces and areas of 
the appliance, taking care not to allow water to enter the burner outlets. 
 
Before each use, check that the screen filter on the ‘gas inlet’ and ‘water inlet’ pipes 
is in place and cleaned of any particles. 

 

DO NOT submerge the appliance in a sink or bowl. 

 

DO NOT use abrasive cleaners or bleach. 

 

   

 


background image

13 

TROUBLESHOOTING   

This guide should be followed in case of failure of the appliance to operate correctly. 
If problems persist contact us. 
 

DO NOT MODIFY THE APPLIANCE. DO NOT ATTEMPT TO REPAIR THE 
APPLIANCE. 

 

Problem 

Cause 

The appliance will 
not light at all 

Make sure you have new batteries installed in the correct 
position. Check the cap of the battery case for instructions on 
how they should be installed. 
Check for sufficient water pressure. The unit must have a 
minimum of 0.25 MPa of sustained water pressure to activate 
the burners.  
There may be debris or epoxy residue in the water regulator. 
Check that the water inlet filter screen is clean. To flush the 
system, you can reverse the hookup by taking the water inlet 
pipe and hooking it up to the water outlet side and back. 
The gas cylinder may be contaminated by air. Turn the unit on 
and off several times to purge the air from the gas. 
Check that the shower flow water regulator is in the open 
position. 

Water flows 
through the unit, 
but is not hot 

New batteries may be required for the ignition switch. Check 
the cap of the battery case for instructions on how they should 
be installed. 
Check that the water pressure is at least 0.25 MPa to activate 
the burners. 
Ensure that the liquid propane regulator is threaded all the 
way to the unit and that you have an adequate amount of gas 
in your propane bottle. 
Verify that you have hooked up both the incoming and 
outgoing water supply properly. The showerhead should be 
attached to the water outlet (located at the centre) and the 
water inlet should be attached to your incoming connection 
(located at the far right) as labelled. 

Water is not hot 
enough 

Adjust the gas regulator and water regulator to meet your 
desired temperature. To increase temperature, turn the gas 
regulator control from minimum to maximum and turn the 
water regulator control from maximum to minimum. 
Turn the burner control knob, in the centre of the unit, to the 
Winter setting.  This will activate more burners. 
Check source water temperature. If the source water 
temperature is too cold then you can ‘cycle’ the water (see 

WATER CYCLING INSTRUCTIONS

 on page 11). 

Check that there is a blue flame in the ‘viewing window’. If you 
see a yellow flame it could mean a breakdown in the gas 
regulator. Please call us directly if this happens; do not 
attempt to use the heater. 

 

 

 


background image

14 

The unit starts for 
a short amount of 
time and then 
shuts off 

Check your gas cylinder to ensure it is not empty. If using a 
new cylinder, try to cycle the unit on and off by using the 
showerhead switch several times to purge the air from the gas 
lines. 
 
You can check if the gas cylinder is empty by using a 
scale.  Disconnect the bottle and place it on a scale, making 
sure the valve is firmly closed.  The tare (empty) weight of the 
bottle is stamped on the neck ring. The difference between the 
scale reading and the tare weight indicates approximately how 
much gas is in the bottle. 
Do not expose the water heater to strong winds. 
This unit activates at a sustained water pressure of 0.25 MPa. 
If your supply water pressure is below the minimum, the unit 
will not ignite. 

SPECIFICATIONS   

Model number 

Portable 8 

Injector size 

0.62 mm 

Total nominal gas consumption 

28 MJ/h 

Gas pressure 

2.8 kPa 

Min water pressure 

0.25 MPa 

Max water pressure 

1.0 MPa 

Size 

500 x 300 x 135 mm 

Weight 

5.3 kg 

Gas input connection 

¼

 (with pre-fitted adaptor) 

Water input connection 

½

 

Water output connection 

½

 

 
 

 

 


background image

15 

WARRANTY   INFORMATION   

The Luxline Portable 8 Hot Water System comes with a 2 year warranty (parts and labour), provided it has been 
operated and maintained as per the manufacturer’s specifications outlined in the instruction manual. (These 
specifications comply with AS2658.) 
 
In the event of defects arising from faulty workmanship and/or materials for a period of two years from the date of 
purchase, Luxline will replace or repair the unit free of charge. In accordance with Australian Consumer law, you 
are entitled to a refund or a replacement in the event of a major failure, and compensation for any other 
reasonably foreseeable loss or damage. You are also entitled to have the unit replaced or repaired if it fails to be 
of acceptable quality and the failure does not amount to a major failure. 
 
When a legitimate warranty claim is made, Luxline is responsible for the cost of the repairs, which include: 
• Any transport or postage costs associated with sending the Luxline Hot Water System from the repair centre to 
the customer. 
• Parts and labour for up to two years after the date of purchase. 
 
Luxline is not responsible for: 
• Any transport or postage costs associated with sending the Luxline Hot Water System to an approved repair 
centre for an under-warranty assessment 
• Any costs for repairs (including labour and call-out fees) where a Luxline Service Agent was not used. 

Warranty   Conditions   

These are the benefits provided to you by this warranty and in addition to other rights and remedies available to 
you under the law. 
 
All Luxline Portable 8 Hot Water Systems must be used and serviced in accordance with the manufacturer’s 
instruction manual (which complies with AS2658). 
 
Any service, inspection, repair or replacement activities associated with Luxline products must only be carried out 
by an approved Luxline agent. To claim this warranty, the customer will need to provide proof of purchase in the 
form of a receipt or financial transaction statement in the name of the purchaser. 
 
This warranty only applies to the Luxline Portable 8 Hot Water System and its internal components. The warranty 
does not include any accessories, fittings, attachments or pumps after the initial 30 days of purchase. 
 
In the circumstance where a failed component is replaced under warranty, the balance of the original warranty will 
remain effective. The replacement part does not carry a new warranty. 
If the Luxline Portable 8 Hot Water System is deemed not to be faulty or not covered under warranty, a service 
fee will be charged. Return postage costs will be the responsibility of the customer. 
 
Customers who want to make a warranty claim must contact the Luxline Service Centre. No hot water systems 
will be assessed without proof of purchase. 

Warranty   Exclusions   

The warranty will become void in the following circumstances: 
• The tamper sticker has been damaged or removed from the hot water system. 
• The hot water system has been damaged through accidental damage, abuse, improper use, acts of god, or 
improper maintenance. 
• The hot water system has been altered or repaired by persons other than a Luxline approved repairer. 
• The hot water system has been damaged through sediment and/or sludge in the water supply. 
• The hot water system has been damaged through frozen water in the pipes. (The instruction manual includes 
instructions for drainage). 
 
Additionally, the warranty only applies to the original purchaser – it cannot be transferred. 

 


background image

 
 
 

 

 

 

1300 371 858 

luxline.com.au / luxline.co.nz