PDF User Manual

  1. Home
  2. Manuals
  3. LockMaster SFG 18H User Manual

LockMaster SFG 18H User Manual

SFG 21H

Made by: LockMaster
Type: User Manual
Category: Gate Opener
Pages: 18
Size: 1.07 MB

 

Download PDF User Manual



Full Text Searchable PDF User Manual



background image

 

www.WholesaleGateOpener.com

 

Rev 11a 

 


background image

 

1

Table of Contents 

 

General Safety ………………………………………..…………………………………......………………….. 2 

Important Safety Instructions ………………………………………..…………………………………........… 3 

Preparation for Installation ………………………………………..…………………………………......…….. 5 

Parts List ………………………………………..…………………………………......…………………………. 6 

Technical Specifications & Feature ………………………………………..………………………………….... 7 

Installation Overview ………………………………………..…………………………………......……………. 8 

Installation of the Opener ……………………………………..…………………………………...... ………. 8 

Manual Operation ………………………………………..…………………………………......……………….. 9 

Fit The Rack ………………………………………..…………………………………......…………………… 9 

Installation of the Limit Switch ………………………………………..…………………………………......... 11 

Connecting of the Control Board …………………………………………..……………………………………. 11 

Setting of the Control Board …………………………………………..…………………………………......….. 13 

Test the reversing sensitivity ……………………………………………………………………….................... 14 

How to learn or erase the remote ………………………………….………..……………………………… 15 

How to use the remote to control the operator ………………………………………..……………………… 15 

Trouble Shooting ………………………………………..…………………………………......………………. 15 

Maintenance ………………………………………..……………………………………………………………… 16 

 

 

 

 

 

 

 

 

 

 

 

 

 


background image

 

2

Thank you for purchasing SFG18 /21H sliding gate opener. We are sure that the products will be greatly 
satisfying as soon as you start to use it. 
The product is supplied with a user’s manual which encloses installation and safety precautions. These 
should be read carefully before installation and operation as they provide important information about safety, 
installation, operation and maintenance. This product complies with the recognized technical standards and 
safety regulations. 

General Safety 

 WARNING! An incorrect installation or improper use of the product can cause damage to persons, 

animals or properties. 
• Scrap packing materials (plastic, cardboard, polystyrene etc.) according to the provisions set out by current 
standards. Keep nylon or polystyrene bags out of children’s reach. 
• This product was exclusively designed and manufactured for the use specified in the present 
documentation. Any other use not specified in this documentation could damage the product and be 
dangerous. 
• The factory declines all responsibility for any consequences resulting from improper use of the product, or 
use which is different from that expected and specified in the present documentation. 
• Do not install the product in explosive atmosphere. 
• The factory declines all responsibility for any consequences resulting from failure to observe Good 
Technical Practice when constructing closing structures (door, gates etc.), as well as from any deformation 
which might occur during use. 
• Disconnect the electrical power supply before carrying out any work on the installation. Also disconnect 
any buffer batteries, if fitted. 
• Fit an omnipolar or magnetothermal switch on the mains power supply, having a contact opening distance 
equal to or greater than 3,5 mm. 
• Check that a differential switch with a 0.03A threshold is fitted just before the power supply mains. 
• Check that earthing is carried out correctly: connect all metal parts for closure (doors, gates etc.) and all 
system components provided with an earth terminal. 
• Fit all the safety devices (photocells, electric edges etc.) which are needed to protect the area from any 
danger caused by squashing, conveying and shearing. 
• Position at least one luminous signal indication device (blinker) where it can be easily seen, and fix a 
Warning sign to the structure. 
• The factory declines all responsibility with respect to the automation safety and correct operation when 
other supplier’s components are used. 
• Only use original parts for any maintenance or repair operation. 
• Do not modify the automation components, unless explicitly authorized by the factory. 
• Instruct the product user about the control systems provided and the manual opening operation in case of 
emergency. 
• Do not allow persons or children to remain in the automation operation area. 
• Keep radio control or other control devices out of children’s reach, in order to avoid unintentional 
automation activation. 
• The user must avoid any attempt to carry out work or repair on the automation system, and always request 
the assistance of qualified personnel. 
• Anything which is not expressly provided for in the present instructions is not allowed. 
• Installation must be carried out using the safety devices and controls prescribed by the EN 12978 
Standard. 

 


background image

 

3

Important Safety Instructions 

 

WARNING – To reduce the risk of injury or death: 

1) READ AND FOLLOW ALL INSTRUCTIONS. 
2) Never let children operate or play with gate controls. Keep the remote control away from children. 
3) Always keep people and objects away from the gate. NO PERSON SHOULD CROSS THE PATH OF 
THE MOVING GATE. 
4) Test the gate opener monthly. The gate MUST reverse on contact with a rigid object or stop when an 
object activates the non-contact sensors. After adjusting the force or the limit of travel, retest the gate opener. 
Failure to adjust and retest the gate opener properly can increase the risk of injury or death. 
5) Use the emergency release only when the gate is not moving. 
6) KEEP GATES PROPERLY MAINTAINED. Read the owner’s manual. Have a qualified service person 
make repairs to gate hardware. 
7) The entrance is for vehicles only. Pedestrians must use separate entrance. 
8) SAVE THESE INSTRUCTIONS. 

Safety Instructions for Installation 

A. Install the gate opener only when: 
1) The opener is appropriate for the construction of the gate and the usage Class of the gate, 
2) All openings of a horizontal slide gate are guarded or screened from the bottom of the gate to a minimum 
of 4 feet (1.22 m) above the ground to prevent a 2-1/4 inch (57.2 mm) diameter sphere from passing through 
the openings anywhere in the gate, and in that portion of the adjacent fence that the gate covers in the open 
position, 
3) All exposed pinch points are eliminated or guarded. 
4) Guarding is supplied for exposed rollers. 
B. The opener is intended for installation only on gates used for vehicles. Pedestrians must be supplied with 
a separate access opening. The pedestrian access opening shall be designed to promote pedestrian usage. 
Locate the gate such that persons will not come in contact with the vehicular gate during the entire path of 
travel of the vehicular gate. 
C. The gate must be installed in a location so that enough clearance is supplied between the gate and 
adjacent structures when opening and closing to reduce the risk of entrapment.   
D. The gate must be properly installed and work freely in both directions prior to the installation of the gate 
opener. Do not over-tighten the opener clutch or pressure relief valve to compensate for a damaged gate. 
E. For gate openers utilizing Type D protection: 
1) The gate opener controls must be placed so that the user has full view of the gate area when the gate is 
moving. 
2) The placard provided marked in letters at least 1/4-in (6.4-mm) high with the word 

WARNING

 and the 

following statement or the equivalent: “ Moving Gate Has the Potential of Inflicting Injury or Death – Do Not 
Start Gate Unless Path is Clear” shall be placed adjacent to the controls, 
3) An automatic closing device (such as a timer, loop sensor, or similar device) shall not be employed. 
4) No other activation device shall be connected. 
F. Controls intended for user activation must be located at least ten feet (10’) away from any moving part of 
the gate and where the user is prevented from reaching over, under, around or through the gate to operate 
the controls. Outdoor or easily accessible controls shall have a security feature to prevent unauthorized use. 

 


background image

 

4

 

G. The Stop and/or Reset button must be located in the line-of-sight of the gate. Activation of the reset 
control shall not cause the opener to start. 
H. A minimum of two (2) WARNING SIGNS shall be installed, one on each side of the gate where easily 
visible. 

 

I. For a gate opener utilizing a non-contact sensor in accordance Usage Class: 
1) See instructions on the placement of non-contact sensors for each Type of application, 
2) Care shall be exercised to reduce the risk of nuisance tripping, such as when a vehicle trips the sensor 
while the gate is still moving, and in the opening direction. 
3) One or more non-contact sensors shall be located where the risk of entrapment or obstruction exists, 
such as the perimeter reachable by a moving gate or barrier. 
J. For a gate opener utilizing a contact sensor in accordance with Usage Class: 
1) One or more contact sensors shall be located where the risk of entrapment or obstruction exists, such as 
at the leading edge, trailing edge, and post-mounted both inside and outside of a vehicular horizontal slide 
gate. 
2) One or more contact sensors shall be located at the bottom edge of a vehicular vertical lift gate. 
3) One or more contact sensors shall be located at the pinch point of a vehicular vertical pivot gate. 
4) A hardwired contact sensor shall be located and its wiring arranged so that the communication between 
the sensor and the gate opener is not subjected to mechanical damage. 
5) A wireless contact sensor such as one that transmits radio frequency (RF) signals to the gate opener for 
entrapment protection functions shall be located where the transmission of the signals are not obstructed or 
impeded by building structures, natural landscaping or similar obstruction. A wireless contact sensor shall 
function under the intended end-use conditions. 
6) One or more contact sensors shall be located on the inside and outside leading edge of a sliding gate. 
Additionally, if the bottom edge of a sliding gate is greater than 6 inches (152 mm) above the ground at any 
point in its arc of travel, one or more contact sensors shall be located on the bottom edge. 
7) One or more contact sensors shall be located at the bottom edge of a vertical barrier (arm). 

 


background image

 

5

Preparation for Installation 

Before proceeding to your opener installation, check if your gate structure is in accordance with the current 
standards, especially as follows: 
The gate sliding track is linear and horizontal, and the wheels are suitable

the gate should be mounted and 

moving freely. Check that the structure is sufficiently strong and rigid, and that its dimensions and weights 
conform to those listed in the specifications table of this document. Make sure that the gate is plumb and 
level. The fence posts must be mounted in concrete. The gate does not bind or drag on the ground. 
• The gate manual operation can be carried out smoothly along its entire run, and there is no excessive side 
slipping. 
• The opening and closing gate stops are positioned. 

 

WARNING: 

Remember that control devices are intended to facilitate gate operation, but can not 

solve problems due to any defects or deficiency resulting from failure to carry out correct installation or 
maintenance. Take the product out of its packing and inspect it for damage. Should it be damaged, contact 
your dealer. Remember to dispose of its components (cardboard, polystyrene, nylon, etc.) according to the 
current prescriptions. 

Refer to the following Figures for gate installation. 

 

 

 
 
 
 
 
 
 
 
 
 

 
 

In sake of safety, a positive stop must be mounted on the two end of ground track. 

 

 

Using the post or wall as a stop, either directly or indirectly, is not 
recommended so as to protect the post or wall against damaging shock 
from the sliding gate. 

 


background image

 

6

It is suggestion that there is a 4”(10cm) distance at least between the gate edge and the gate wall 
when the gate is fully open. 

 

 

 

 

 

 
 
 
 
 

Parts List 

 

 


background image

 

7

Technical Specifications & Features 

Specifications 

·Power supply: 120V/60HZ or 230V/50HZ 

·Motor: 120VAC or 230VAC 

·Absorbed power: SFG18

370W / SFG21

550W 

·Gate moving speed: 

7.9“/second

 20 cm/second 

·Max gate weight: SFG18:800KGS / SFG21:1200KGS                 

·Max torque: SFG18: 24Nm / SFG21: 35Nm 

·Environmental conditions: from -15°C to +40°C 

·Protection class:  IP44 

·Dimensions: 38×28×36 CM

 

·Class of gate opener: I, II 

Features: 

·Easy to install and low maintain. 

·Midway mode   

·Quick selection for gate open/close direction 

·Reliable rolling code technology 

·Emergency release key in case of power failure 

·Stop/Reverse in case of obstruction during gate opening/closing. 

·Built in adjustable auto-close (5

100 seconds) 

·Built in max. Motor running time (MRT) adjustable for multiple safety protection (5

100 seconds) 

·Reliable electromagnetism limit for easy adjustment 

·Can be equipped with wide range accessories 

 

 

 

 

 

 


background image

 

8

Installation Overview 

 

 
 

Installation of the Opener 

Caution:  
*Be sure that the opener is installed in a level and paralleled position and is properly secured. 
Improper installation could result in property damage, severe injury, and/or death. 
* Before starting installation, ensure that there is no point of friction during the entire movement of 
the gate and there is no danger of derailment. 
* Ensure that the safety side panels are present. 
Necessary Tools: 

The following tools 

may be necessary to install the Gate 
opener. You will need screwdrivers, an 
electric drill, wire cutters and a wire 
stripper, a socket set, and possibly 
access to a welder.

 

When install the opener, you should 
build a concrete pad to support the base 
plate of opener in order to maintain 
proper stability. 

The installation proceeds are as 
follows: 
1.

Dig a hole for a concrete pad which 

should be approximately 50 x 30 x 35cm 
(20

x 12

x 14

). It may protrude 10 

cm (4”) above ground and 25 cm (10”) in 
depth underground. Increase the pad 
height if necessary to protect the system 
from flooding, heavy snow etc.   

2.

 Prepare one or more conduits for the 

electrical cables before pour concrete. 
Remember that cable conduits have to 
pass through the hole in the base plate. 

 


background image

 

9

3. 

Pour concrete and before it starts to harden, check that it is parallel to the gate leaf and perfectly level. 

4. 

Mark the position of four expansion anchors according to the position of mounting hole on the base plate 

as soon as concrete become harden. Double check your marking, move the base plate and drill the 4 holes 
using a 10mm (3/8”) masonry bit. Put the 4 expansion anchors (provided) into the holes and firmly tighten. 

5. 

Place the opener onto base plate. Check that it is perfectly parallel to the gate leaf, and then screw the 

four nuts and washers supplied. It's only temporary installation. Further adjustment will be required when 
install the rack or chain. 
 
 

Manual Operation   

The opener should be put in the manual (emergency release) position before fitting the rack, installing the 
opener and limit switch. The process is as follows: 
1) Insert and turn the key clockwise 45° to slide the lock cover. Now the key slot appears. 
2) Insert the T-handle Key

provided

to the key slot and turn it in counter-clockwise 135° to disengage the 

clutch between the gear shaft and power output. Now the opener is in the manual operation. 

         

 

 
 

Fit the Rack 

There are two kinds of rack available as per buyer’s option, which are steel reinforced plastic rack and 
galvanized steel rack. The galvanized steel rack is usually used for the heavy duty gate. 

A. Fit the plastic rack reinforced with steel   

1. Start with gate in closed position 
2. There are four sections of plastic rack which is one meter length, each section for standard package. (you 
can order extra rack from dealer if necessary)   
2. Put one end of rack section on the gear of opener as a temporary support. 
Make rack level and mark the rack’s mounting holes (four holes) on the gate. 
3. Fit the rack by self-threading screws. This kind of plastic rack is quieter and allows height adjustments to 
be made even after it has been fixed. Please keep 1.0mm space between the rack and the gear to avoid the 
weight of the gate leaf effect on the opener. 

 


background image

 

10

 

B. Fit the galvanized steel rack     

1. Start with gate in closed position 
2. There are four sections of steel rack which is one meter length, each section for standard package. (you 
can order extra rack from dealer if necessary) 
2. Put one end of rack section on the gear of opener as a temporary support. 
Make rack level and mark the rack’s mounting holes (three holes) on the gate. 
3. Weld the rack nut on the gate as mark and connect the rack to the gate using the bolt provided. Before 
weld, please keep 1.0mm space between the rack and the gear to avoid the weight of the gate leaf effect on 
the opener. 

 

 


background image

 

11

Important:  

* Check that the rack teeth must engage the gear teeth throughout their full thickness. If not, adjust the 
position of the opener or/and place a few shims between the rack and gate. 
4. Manually slide the gate leaf to ensure the rack is proper on the gear of opener, weld the second nut. 
5. Repeat same steps of first rack section to install the rest rack sections until proper length is reached. 
6. Cut away any excess of the rack (Note: rack length must be longer than actual travel of the gate to 
accommodate limit switch brackets on each gate side.) 
7. Thoroughly fasten the four nuts as well as spring washers onto expansion bolt tightly, enabling the opener 
is firmly secured on the concrete pad during the whole gate travel. 
 
 

Installation of the magnets for the Limit Switches 

Before install limit switch, make sure the gate opener is put in manual operation. (the clutch connected with 
gear shaft is disengaged) and the mains power supply is disconnected. 
Position the two limit stop brackets approximately on the rack and move the gate by hand to fix them in 
place. 

Fit magnets bracket   

Push the gate fully closed by hand. Locate and install the magnet bracket so that the opener will stop at the 
desired close position when the close limit switch approaches it.   
Push the gate fully open by hand. Locate and install the magnet bracket so that the opener will stop at the 
desired open position when the open limit switch approaches it.   

The higher magnet bracket must be installed at left side and lower magnet bracket must be installed 
at right side from the view inside of property.

 Finally adjust the magnet to the proper position by moving 

the gate with the motor. The magnet should be 39 - 59 “away from the magnetic limit switch. If it is too far 
away, the switch will fail to work. The distance between the magnet and the opener should be 1/2” (12mm) 
with the opener cover on. Adjust the position of the magnet until the positions of the opening and closing 
meet the requirement. 

Important Note: 

Please note the two magnet brackets (fixed plate) are different: one is higher and ano the 

other is lower. 
 
 

Connecting of the control board 

Warning

Before making any electrical wire connection or/and setting the control board, make sure 

that the power switch is OFF. 

 

1. Motor 

The 

BLACK

 wire of the motor should be connected into the “6” terminal. 

The 

RED

 wire of the motor should be connected into the “7” terminal. 

The 

YELLOW

 wire of the motor should be connected into the “8” terminal. 

2. Start Capacitor 

One pin of the start capacitor should be wired to the “7” terminal, another to “8” terminal. 

3. Limit Switches 

The 

RED 

wire of the limit switches should be connected into the “9” terminal. 

The 

BLACK

 wire of the limit switches should be connected into the “10” terminal. 

The 

YELLOW

 wire of the limit switches should be connected into the “11” terminal. 

 


background image

 

12

 

4. Alarm Lamp (Optional) 

One wire of the alarm lamp should be connected into the “4” terminal, another should be connected into the 
“5” terminal. 

 


background image

 

13

5. Photocell (Normal Open) (Optional) 

Use a 2-core cable to connect the 

“+ ~”

 terminal of the photocell’s emitter to the “12” terminal, the 

“- ~”

 

terminal to the “13” terminal. Also the 

“+ ~”

 and 

“- ~”

 terminals of the photocell’s receiver should be 

connected to the “12” and “13” terminals in parallel. 
Use another 2-core cable to connect the 

“NO”

 terminal of the receiver to the “14” terminal, the 

“COM”

 

terminal to the “15” terminal.

 

6. Push Button (Optional) 

The push button should be wired to the “15” and “16” terminals. The gate operator works alternately by 
pushing the button (open-stop-close-stop-open).

 

7. Loop Detector (Optional) 

First insert the 

LOOP DETECTOR BOARD

 into the 

CONTROL BOARD

, and then connect the twisted-pair 

to the “17” and “18” terminals. 

8. External Receiver (Optional) 

The 

BROWN

 wire of the external receiver should be connected into the “16” terminal. 

The 

BLACK

 wire of the external receiver should be connected into the “13” terminal. 

The 

RED

 wire of the external receiver should be connected into the “12” terminal. 

9. Wired Keypad (12VDC) (Optional) 

The 

RED

 wire of the wired keypad should be connected into the “12” terminal. 

The 

BLACK

 wire of the wired keypad should be connected into the “13” terminal. 

The 

WHITE

 wire of the wired keypad should be connected into the “16” terminal. 

The 

BLUE

 wire of the wired keypad should be connected into the “15” terminal. 

 

 

Setting of the Control Board 

1. DIP Switches 

The DIP switches are used to set 
the running time of the motor in 
midway mode, auto close time of 
the gate operator and fast change 
the open/close direction which is 
determined by the position of the 
gate operator installed. 
 
 

DIP Switch #1–#2: Running time of the motor in Midway Mode

 

This mode enables user to drive the vehicle through the gate quickly when the gate opens to certain width. 

DIP Switch #1: ON

 – 2 Seconds 

OFF

 – 0 

DIP Switch #2: ON

 – 4 Seconds 

OFF

 – 0 

NOTE: The midway function would be disabled if both DIP switches are turned off. Factory default 
setting is disabled. 
 
 
 
 
DIP Switch #3–#4: Auto close time of the gate operator 
DIP Switch #3: ON

 – 30 Seconds 

OFF

 – 0 

E.g.                   Running time of the operator in midway mode is 2+4=6 seconds. 

 


background image

 

14

DIP Switch #4: ON

 – 60 Seconds 

OFF

 – 0 

NOTE: The auto close function would be disabled if both dip switches are turned to off (factory 
default setting). 

 
 

 
 
DIP Switch #5: Left/Right open 
ON

 – Left open (factory default setting).   

OFF

 – Right open. Turn switch OFF to change the opening direction easy if necessary. 

 

 
2. Potentiometers 

The potentiometer A is to adjust the 

OPEN

 stall force of the gate operator. The Potentiometer B is used to 

adjust the 

CLOSE

 stall force of the gate operator. 

Turn the potentiometer clockwise to increase the stall force. 
Turn the potentiometer counter-clockwise to decrease the stall force. 

 

 
 
 
 
 
 
 
 
 
 
 
 

 

 
 

Test the reversing sensitivity 

For the sake of safety, it is very important to test the reversing sensitivity as soon as the control board set is 
finished. 
The reversing sensitivity adjustment is inverse correlation with stall force adjustment in 

potentiometer A 

and potentiometer B

. In other word, the stall force level is higher; the reversing sensitivity level is lower. 

E.g.                   Auto close time of the gate operator is 30+60=90 seconds. 

 


background image

 

15

Put an immobile object along the gate path, and then operate the gate to strike it during the open and close 
cycles. The gate must reverse as soon as object is struck with it. If the gate doesn’t reverse, please increase 
the reversing sensitivity by turning the potentiometer in counter-clockwise direction. (Turning the stall force 
potentiometer toward to MIN position to increase the reversing sensitivity) 

Note 1: If the sensitivity setting is too higher, the gate will stop or reverses very easy by itself while 
there is little obstruction or resistance such as strong wind or heavy snow sometimes. 
Note 2: Always check the gate reversing function every each time of control board set or restart after 
power off.   

 
 

How to learn or erase the remote 

Learn the remote 

Press and release the learn button, the 

REM

 

LED

   

light will be on, then press the key in the   
remote twice in 2 seconds, the 

REM LED 

light will flash for 4 seconds. Now the   
remote has been learnt successfully. 

Erase all the remote codes 

Press and hold the learn button until the 

REM

 

LED

 light is off. Now all remote codes have been erased. 

 
 

How to use the remote to control the operator 

Key A 

is used to operate the operator to work alternately (open-stop-close- 

stop-open). 
When the Midway Mode function is enabled, 

Key B

 is used to achieve the 

Midway Mode function (open the gate for the pre-setting time). When the 
Midway Mode function is disabled, the operator works alternately (open-stop 
-close-stop-open) by pressing 

Key B

 
 

Troubleshooting 

Have a multimeter to check voltage and continuity. Use caution when checking high voltage terminals. 

1. Motor only runs toward one direction. 

a. The limit switch is failed. Disconnect the limit switches and try it again. 
b. The start capacitor of the motor is failed. Replace the capacitor. 
c. The electric component on the control board may be damaged. Replace the electric component or replace 
the control board. 

2. The gate does not open or close. 

a. The power switch is OFF. Make sure the power switch is ON. 
b. The limit switches are failed. Disconnect the limit switches and try it again. 
c. Connecting wires or terminal blocks are too loose. Check the connecting wires and terminal blocks. 
d. The motor has been damaged. Replace the motor if necessary. 
e. The thermal protector is working because the high temperature after long working time. Please wait for 20 
minutes to let the motor become cold. 

 


background image

 

16

f. The electric component on the control board has been damaged. Replace the electric component or 
replace the control board. 

3. Remote control does not work. 

a. The distance you use the remote is too far away from the opener. Try it again closer. 
b. Remote control is not suitable for receiver. After making sure the codes are correct, erase remote controls 
and then re-program the codes in the device. 
c. Broken receive board. Replace receive board. 
d. The indicator light of remote control is not on. Check the battery in your remote control. Replace the 
battery if necessary. 

4. When you open or close the gate by pressing key #1 and key #2 which have been programmed, 
gate will stop in mid-travel or reverse before reaching the fully limit position. 

a. The opening force or closing force is adjusted too small. Turn the Potentiometer 1 and 2 to increase the 
force. 
b. Gate is obstructed. Remove the obstruction. 

5. The gate opens, but stops and will not return. 

a. Please note the two magnet brackets (fixed plate) are different: one is higher and another is lower. Please 
try to exchange the two brackets position. 
b. Please try to exchange the limit switch wires CL (close) and OP (open). There are two reed switches 
inside the magnetic limit switch: one is upper and another is lower. Maybe the magnet position was installed 
in the middle so it inducts both switches. Adjust the magnet upper or lower. 

6. The gate can open, but fails to close. 

a. Photocell is obstructed. Remove obstruction. 
b. The limit switch is failed. Disconnect the limit switches and try it again. 
c. The start capacitor of the motor is failed. Replace the capacitor. 
d. The electric component on the control board has been damaged. Replace the electric component or 
replace the control board. 

7

The motor runs but the gate doesn’t move. 

The clutch for emergency release is adjusted properly and is not slipping. 

 
 

Maintenance 

Every six months check the following items for proper operation of the unit. 
* Lubricate shafts and sprockets. 
* Keep operator clean at all times. 
* Check and tighten anchors bolts. 
* Check for loose or corroded wire 
* Ensure the operator is well earthed, and correctly terminated. 
* Always check the Stop/Reverse in case of obstruction function when performing any maintenance. If this 
function can’t be made operable, remove this operator from service until the cause of the malfunction is 
identified and corrected.   

 

 
 
 

 
 

 


background image

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

www.WholesaleGateOpener.com

 

7106 S 220th St, Kent WA 98032 USA 

sales@WholesaleGateOpener.com

 

  ©2010-2012 LockMaster All Rights Reserved