PDF User Manual

  1. Home
  2. Manuals
  3. Lexmark 1361760 Manual

Lexmark 1361760 Manual

1361760 K30CLR

Made by: Lexmark
Type: Manual
Category: Printer Accessories
Pages: 1
Size: 0.65 MB

 

Download PDF User Manual



Full Text Searchable PDF User Manual



background image

Q: Cartridge will not print?
A:

 If the cartridge does not print after

     refilling, rest the print nozzles on a 
     wet tissue. This will draw ink through
     the nozzles. Leave for 10 minutes 
     and try printing again.  

Use a blade or sharp knife to remove the cap
from the top of the cartridge. Insert the blade
into the sealing joint between the cap and
the body and carefully pry it off . Note: Be 
very careful not to break the cap.

Cap

Phone Support
  1300 730 018

E

a

s

re

f

ls

y

il

P

a

ra

ti

re

p

o

n

- Put on the gloves supplied 

- Cover your work area in newspaper
   in case of accidental spillage. 

- Read these instructions thoroughly

- Remove the cartridge from your 
  printer (only do this when 
  ready to refill.)

NB:

 Ink stains so we would 

       recommend you wear old 
       clothes or an apron when 
       refilling.
   

Preparation:

Kit Contents:

3 x ink bottles (blue, red, yellow)
1 x plastic gloves 
1 x absorbent pad
4 x stickers

1

S

e

p

 

t

O

n

e

e

p

S

t
 T

h

re

e

3

2

S

e

p

 

t

T

w

o

S

te

p

 F

o

u

r

e

S

t

p

 F

iv

e

e

p

 
i

S

t

S

x

5

6

4

T

b
 
o
i

ro

u
le

s

h
o

t

n

g

?

Q: Prints with streaks through text or
     image?
A: 

This could mean that the print nozzles 

     are blocked, therefore preventing ink to 
     flow freely. To correct this problem use 
     the printers cleaning routine. If this does
     not work, rest the print nozzles on a wet
     tissue. This will draw ink through the 
     nozzles. Leave for 10 minutes and try
     printing again. 

Q: Ink stains on hands and clothes?
A: 

To clean your hands, first wash

     thoroughly in soap and warm water.
     If the stains persist, try using bathroom 
     cleaner. It may take several washes to 
     remove the ink. There is no real solution 
     to ink stained clothes. However if you 
     are using a dy cleaner, you can tell them 
     the ink is based upon water soluble dye 
     with ethylene glycol added.
  

S

te

p

 S

e

v

e

n

7

Matchstick

Replace the cap on top of the cartridge 
(see step 2) and secure with two of the
stickers provided. Alternatively you can use 
super glue or a hot melt glue gun to stick  
the cap back on. 

S

e

p

 
i

h

t

t

E

g

Using the absorbent pad, clean any 
foreign materials or excess ink. If
the nozzles on the bottom of the cartridge
leak, blot with tissue until leaking stops. 

Lexmark 

1361760

Printer Compatibility:

Lexmark PM-100,PM-3200,5000,5700,7000,
7200,OPTRA COLOR 40,40n,45,45n,45n 
SOLARIS,Z11,Z31

Instructions

www.easyrefills.com.au

Kit Code: K30CLR

l

G

e

n

e

ra

 I

n

fo

rm

a

ti

o

n

Easyrefills manufacturers all refill kits at it’s
Queensland headquarters. Importing the 
finest quality American made inks that are 
in most cases better than or equal to 
original manufacturers specifications. Each
kit has a shelf life of two years and is 
covered by a 100% guarantee.

Cartridge Stats:

Colour: Tri-colour (Red, Blue, Yellow)
Ink Capacity: 5 ml per chamber
Weight when full: 68 grams

Number of refills per kit:

8 refills per kit

AUSTRALIAN MADE

www.easyrefills.com.au

E

s

 

t

a

y

re

fi

lls

k

i

Copyright 2004 Easyrefills. All names and numbers used are 
         registered trademarks of their respective owners.

Insert the plug provided into the refilling
hole. Gently squeeze the sides of the 
cartridge while resealing the hole. An air
tight seal must be formed. Cover the hole
and plug with one of the stickers provided.

8

Using the drill tool provided, drill a hole 
at point ‘A’. Once you have penetrated the 
first layer of plastic you will meet a sponge.
Stop drilling when you feel this sponge.

Insert the refill needle into the hole containing 
the ink you wish to refill. Angle the needle 
toward the ink outlet hole at the bottom of 
the cartridge and push down as far as 
possible.

S-l-o-w-l-y and gently squeeze the ink refill 
bottle to force ink into the cartridge. This 
must be done with very little pressure, pulling
the needle upward as you go. Each chamber
takes approximately 5ml of ink. 

Repeat Steps 4-5  for each colour you wish
to refill. Using the absorbent pad clean any 
foreign materials or excess ink from the 
top of the cartridge.

Install the cartridge into your printer and
run the head cleaning utility (see printer 
manual). For best results wait 20 minutes 
before you resume printing. 

Place the cartridge on the absorbent pad 
provided. If a few drops of ink leak onto 
the pad do not worry, this is normal.

Identify which colour is under each refilling 
hole by using the end of a matchstick or
toothpick as shown above. Insert the match-
stick into the hole as far as possible,
remove and check for colouring on stick.

View From Top

Body

Print Nozzles

Sealing joint

Cap

Body

Sticker #1