PDF User Manual

  1. Home
  2. Manuals
  3. Leviton Remote control HCCUR Owner's Manual

Leviton Remote control HCCUR Owner's Manual

Made by: Leviton
Type: Owner's Manual
Category: Remote Control
Pages: 16
Size: 0.15 MB

 

Download PDF User Manual



Full Text Searchable PDF User Manual



background image

Universal Remote Control

Cat. No. HCCUR

Owners Manual

DI-000-HCCUR-00A

DI-000-HCCUR-00A

7/5/02, 2:18 PM

1

 


background image

R

EAD

 T

HIS

 F

IRST

!

S

AFETY

 C

ONSIDERATIONS

Remember to exercise good common sense when using
the Home Automation features of your Remote - especially
when scheduling unattended devices. There can be some
unexpected consequences if not used with care. For
example, an empty coffee pot can be remotely turned on.
If that should happen, your coffee pot could be damaged
from overheating. If an electric heater is turned on by
remote control while clothing is draped over it, a fire could
result. DO NOT USE the remote for the control of high power
heating appliances such as portable heaters.

WARNING:

 TO PREVENT ELECTRIC SHOCK HAZARD, DO

NOT EXPOSE ANY PART OF THE HOME AUTOMATION SYSTEM
TO RAIN OR MOISTURE

CAUTION:

 TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT DISASSEMBLE ANY PART OF THE HOME AUTOMATION
SYSTEM’S PLUG-IN MODULES OR CONTROLLERS. NO USER-
SERVICEABLE PARTS ARE INSIDE. IF YOU SPILL LIQUID ON A
UNIT, DISCONNECT THE UNIT FROM THE AC OUTLET TO
PREVENT POSSIBLE FIRE OR SHOCK HAZARD AND CONSULT
AUTHORIZED SERVICE PERSONNEL.

POWERLINE OPERATED EQUIPMENT OR ACCESSORIES
CONNECTED TO ANY OF THESE UNITS SHOULD BEAR THE UL
LISTING OR CSA CERTIFICATION MARK AND SHOULD NOT
HAVE BEEN MODIFIED IN ANY WAY THAT MIGHT DEFEAT THEIR
SAFETY FEATURES.

2

DI-000-HCCUR-00A

7/5/02, 2:19 PM

2

 


background image

FCC C

AUTION

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.

OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS:

(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE,

AND

(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,

INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED
OPERATION.

This equipment generates and uses radio frequency
energy, and if not installed and used properly, that is, in
strict accordance with the manufacturers instructions, it
may cause interference to radio and television reception. It
has been type tested and found to comply with the limits
for remote control devices in accordance with the
specifications in Sub-Parts B and C of Part 15 of FCC Rules,
which are designed to provide reasonable protection
against such interference in a residential installation.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause interference to radio or television reception, which
can be determined by unplugging the equipment, try to
correct the interference by one or more of the following
measures.

Reorient the antenna of the radio/TV experiencing the
interference.

Relocate the interface with respect to the radio/TV.

Move the interface away from the radio/TV.

Plug the interface into an outlet on a different electrical
circuit from the radio/TV
experiencing the interference.

If necessary, consult your local Dealer for additional
suggestions.

NOTE:

 Modifications to any of the components in this kit will

void the user’s authority to operate this equipment.

3

DI-000-HCCUR-00A

7/5/02, 2:19 PM

3

 


background image

C

ONTENTS

I

NTRODUCTION

.................................................................. 5

G

ETTING

 S

TARTED

.............................................................. 6

6-

IN

-1 R

EMOTE

.............................................................. 6

S

ETTING

 U

P

 

YOUR

 R

EMOTE

................................................... 6

B

UTTON

 D

ESCRIPTIONS

..................................................... 6

S

ETTING

 

UP

 

FOR

 TV, VCR,

C

ABLE

 B

OX

 

AND

 S

ATELLITE

 R

ECEIVER

.................................. 8

U

SING

 AUX 

TO

 

CONTROL

A

 S

ECOND

 TV, VCR, C

ABLE

 B

OX

 

OR

 S

ATELLITE

 R

ECEIVER

...... 9

S

EARCHING

 F

OR

 C

ODES

................................................ 10

I

DENTIFYING

 C

ODES

 

FOUND

 

USING

THE

 S

EARCH

 P

ROCEDURE

................................................ 11

S

ETTING

 

THE

 TV S

LEEP

 T

IMER

........................................... 12

C

ONTROLLING

 M

ODULES

.................................................. 12

T

O

 

SET

 

THE

 HC S

LEEP

 T

IMER

............................................ 13

C

HANGING

 

THE

 H

OUSE

 C

ODE

: ....................................... 14

T

ROUBLESHOOTING

........................................................... 15

W

ARRANTY

.................................................................... 16

4

DI-000-HCCUR-00A

7/5/02, 2:19 PM

4

 


background image

I

NTRODUCTION

Congratulations on your purchase of a Leviton Universal
Remote Control.

Make your lights and appliances go to work for you....

The Remote will control most or all of your video and audio
equipment. But what really sets it apart from other remotes
is that you can also control almost any light or appliance
in your home - even in another room! And it’s easy to set
up. Within minutes, you can be using your Remote to dim
the lights, start brewing a fresh pot of coffee and play your
favorite movie!*

Here are just some of the things you can do with your
Remote...

Control your entire audio/video and lighting setup for
the ultimate Home Theater experience.

Turn on lights at night to scare away intruders if you
hear a noise.

Start the coffee from your bedroom when you wake
up.

Turn on your electric blanket before the movie ends, so
you it’s nice and warm when you go to bed.

Use this manual to become familiar with your Remote....

This manual will explain how to set up your Remote to use it
with your existing Audio/Video equipment.

Next it will show you how you can use it to set up a
Transceiver Module and Lamp Module (sold separately) to
operate electrical products in your home.

* Requires Leviton Home Control Modules, sold separately.

5

DI-000-HCCUR-00A

7/5/02, 2:19 PM

5

 


background image

G

ETTING

 S

TARTED

6-

IN

-1 R

EMOTE

The 6-in-1 Remote lets you control practically everything
electrical in your home. It has IR technology that lets you
control all your TV, VCR, Cable and Satellite equipment,
and RF technology that lets you control lamps and
appliances anywhere in your home.

To find out more about configuring the Remote to work
with your audio/video equipment, refer to the following
section titled “Setting Up Your Remote.”

1.

Push the tab and lift off the battery cover.

2.

Fit two AAA batteries, taking care to
match the + and - marks in the battery
compartment.

S

ETTING

 U

P

Y

OUR

 R

EMOTE

B

UTTON

 D

ESCRIPTIONS

INDICATOR LIGHT

The indicator light flashes when the remote is operating.

POWER

Works in the same way as your original remote.

SET UP

Used for programming the remote.

HOUSE SYMBOL

Lets you control modules to operate lamps and
appliances around the home.

6

DI-000-HCCUR-00A

7/5/02, 2:19 PM

6

 


background image

TV, VCR, CBL, AUX1, AUX2, SAT

Used to select the device to control. SAT includes DBS
receivers.

0-9

Used as your original remote and to enter device codes.

LAST

Selects the last channel viewed on your TV, VCR, Cable
Box or Satellite Receiver.

CHANNEL +/-

Works like your original remote. Also used to switch
modules on and off.

MUTE

Works the same as your original remote.

VOLUME +/-

Works like your original remote. Also used to brighten and
dim lamps connected to Modules.

TIMER

Used to set the Sleep Timer to automatically switch off the
TV or modules after a preset time.

CAP (CAPTION)

Has different function depending on Mode e.g. TV Closed
Caption in TV Mode.

PLAY, REW, FF, STOP, PAUSE

Work the same as on your original remote.

REC

Record button. Works the same as your original remote.
You must press the REC button twice to begin recording.

SHIFT

For accessing additional functions.

DISP (DISPLAY)

Used to access on-screen information

7

DI-000-HCCUR-00A

7/5/02, 2:19 PM

7

 


background image

S

ETTING

 

UP

 

FOR

 TV, VCR, C

ABLE

 B

OX

 

AND

 S

ATELLITE

 R

ECEIVER

1.

Turn on the device you want to control (TV,
VCR, cable box, satellite receiver etc.).

2.

Press and hold SETUP until the LED
indicator lights steadily. Release the SETUP
button.

3.

Press and release mode button for the
device you want to control. The LED blinks
once. Use AUX1 or AUX2 for CD
equipment.

4.

Enter the 3 digit Code from the Code List
(separate sheet). The LED turns off after
the last digit entered.

5.

Point the remote at the device and press
the POWER button. Your device should
turn off.

6.

Turn your device on and press CHANNEL+.
If the device responds, setup is complete.

NOTES:
For CD players 

use the AUX 1 or AUX 2 buttons.

If your TV/VCR/Cable Box/Satellite Receiver does not
respond

, try the other codes for your brand. If it still doesn’t

respond, try the Code Search method on page 10.

If the LED blinked rapidly when you entered the code

, you

may have entered an invalid code. Recheck the code in
the code list (separate sheet) and try again.

If some buttons do not operate your equipment

, try one of

the other codes for your brand.

8

DI-000-HCCUR-00A

7/5/02, 2:19 PM

8

 


background image

U

SING

 AUX 

TO

 

CONTROL

 

A

 S

ECOND

 TV, VCR, C

ABLE

 B

OX

OR

 S

ATELLITE

 R

ECEIVER

The AUX button is normally used to control an audio
component, but it can also be configured to control a
second TV, VCR, cable box or satellite receiver.

1.

Turn on the equipment you want to control.

2.

Press and hold SETUP until the LED
indicator lights steadily. Release Setup
button.

3.

Press the AUX1 or AUX2 button.

4.

Press and release the mode button that
matches the A/V equipment you want to
control. The LED blinks once.

5.

Enter the 3 digit Code from the Code List.
The LED turns off after the last digit
entered.

6.

Point the remote at your audio
component and press the POWER button.
Your audio component should turn off.

7.

Turn your audio component on and press
CHANNEL +. If it responds, setup is
complete.

9

DI-000-HCCUR-00A

7/5/02, 2:19 PM

9

 


background image

NOTES:

If your audio/video component does not respond

, try the

other codes for your brand. If it still doesn’t respond, try the
Code Search using the followingmethod.

If the LED blinked rapidly when you entered the code

, you

may have entered an invalid code. Recheck the code in
the code list (separate sheet) and try again.

S

EARCHING

 F

OR

 C

ODES

1.

Turn on the device you want to control.

2.

Press and hold SETUP until the LED
indicator lights steadily. Release Setup
button.

3.

Press the mode button that matches the
equipment you want to control. The LED
blinks once.

4.

Press CHANNEL + repeatedly* until the
device to be controlled changes channel.

If you accidentally go past the code,  press

CHANNEL -repeatedly until the channel
changes again.

5.

Press and release the ENTER button to
complete the setup.

*NOTE:

 You might have to press CHANNEL+ many times

(50+). If the device does not have a Channel Up function,
use the PLAY button (VCR only) or the POWER button.

10

DI-000-HCCUR-00A

7/5/02, 2:19 PM

10

 


background image

I

DENTIFYING

 C

ODES

 

FOUND

 

USING

 

THE

 S

EARCH

 P

ROCEDURE

1.

Press and hold the SETUP until the LED
indicator lights steadily. Release Setup
button.

2.

Press the mode button that matches the
equipment you want to identify. The LED
blinks once.

3.

Press and release SETUP. The LED blinks
once.

4.

To find the first digit, press each number
button from 0 to 9 until the LED blinks. The
number you pressed is the first digit of the
code.

5.

Press each number button from 0 to 9
again as above to find the second digit.

6.

Press each number button in turn to find
the third digit. When the third digit has
been found, the LED goes out.

11

DI-000-HCCUR-00A

7/5/02, 2:19 PM

11

 


background image

S

ETTING

 

THE

 TV S

LEEP

 T

IMER

The Sleep Timer automatically turns off the TV after the time
you set. Press the TV button, then follow the
instructions below to set the Sleep Timer:

1.

Press and hold TIMER until the LED

indicator lights steadily. Release the TIMER
button.

2.

Use the number buttons to enter the sleep
time required (1 to 99 minutes).

3.

Press ENTER to confirm the setting.

NOTE:

 Take care to leave the remote pointing at

the TV to ensure it turns off the TV at the time you
set.

C

ONTROLLING

M

ODULES

If you have purchased and installed a Transceiver Module,
you can control it and other modules as follows:

1.

Press and release the button with the
House symbol on it.

2.

Use the number buttons to enter the Unit
Code number of the chosen module. (You
do not need to enter ‘0’ first for a single
digit number.)

3.

Press the appropriate button for the
function you require (refer to next page).

12

DI-000-HCCUR-00A

7/5/02, 2:19 PM

12

 


background image

HOME CONTROL FUNCTIONS:

On:

CHANNEL +

Off:

CHANNEL –

Bright:

VOLUME +

Dim:

VOLUME –

All Lamps On:

POWER

All Modules Off: MUTE

NOTE:

 You cannot dim or brighten an Appliance Module. If the

module was off and you press Bright or Dim (VOLUME+ or
VOLUME-) this will simply turn the module on.

T

O

 

SET

 

THE

 H

OME

 C

ONTROL

 (HC) S

LEEP

 T

IMER

The Sleep Timer switches off the chosen modules after the
preset time.

1.

Press and release the button with the
House symbol on it.

2.

Press and hold TIMER until the LED
indicator lights steadily. Release the TIMER
button.

3.

Use the number buttons to enter the
module Unit Code for the module to be
turned off.

4.

Press the desired function button (e.g.
CHANNEL - to turn the module off after the
preset time).

5.

Using the number buttons enter the sleep
time required (1 to 99 mins).

13

DI-000-HCCUR-00A

7/5/02, 2:19 PM

13

 


background image

6.

Press ENTER to confirm the setting.

C

HANGING

 

THE

 H

OUSE

 C

ODE

:

The Remote defaults to House Code A, and in most cases
you will not need to change this unless you are
experiencing interference from a neighboring Home
Control system.

1.

Press and release the button with the
House symbol on it.

2.

Press and hold SETUP until the LED
indicator lights steadily. Release Setup
button.

3.

Use the number buttons to enter the
number equivalent to the chosen House
Code (1=A, 2=B ..16=P).

4.

Press the ENTER button to confirm the
House Code. The LED turns off.

NOTE: 

The House Code you choose must match

the House Code on the Transceiver and Modules
you are using it with.

14

DI-000-HCCUR-00A

7/5/02, 2:19 PM

14

 


background image

T

ROUBLESHOOTING

The Transceiver Module doesn’t respond to the remote:

Check the House Code on the Transceiver Module is
set to ‘A.’ If you have changed the House Code on the
remote (see p. 19), check that it matches the House
Code on the module.

Press the ON/OFF button on the front of the Transceiver
to confirm it operates the equipment connected to it.

The Transceiver Module works, but other modules don’t
respond:

Check that the Module has the same House Code as
the Transceiver Module.

Try plugging the Module into a different outlet.

NOTE:

 when you use an RF Transceiver (such as the HCPRF)

to control Modules, you will be able to control up to 16
Modules. E.G., when you press 1-6-ON you turn on Module
number 16.

The Remote won’t control your Audio/Video equipment, or
doesn’t work at all:

Use manual controls or the original remote control to
confirm the equipment is working properly.

Be sure you pressed the device key for the device you
want to control.

Reenter the code for your A/V product from the code
listings on the separate sheet included.

Try searching for codes as described on page 10.

Replace the Remote’s batteries.

15

DI-000-HCCUR-00A

7/5/02, 2:19 PM

15

 


background image

LIMITED 2 YEAR WARRANTY AND EXCLUSIONS

Leviton warrants to the original consumer purchaser and not for the benefit of
anyone else that this product at the time of its sale by Leviton is free of defects
in materials and workmanship under normal and proper use for two years
from the purchase date. Leviton’s only obligation is to correct such defects by
repair or replacement, at its option, if within such two year period the product
is returned prepaid, with proof of purchase date, and a description of the
problem to Leviton Manufacturing Co., Inc., Att: Quality Assurance
Department, 59-25 Little Neck Parkway, Little Neck, New York 11362-
2591 (In Canada send to Leviton Mfg. of Canada Ltd., 165 Hymus Blvd.,
Point Claire, (Quebec), Canada H9R 1E9)
. This warranty excludes and there
is disclaimed liability for labor for removal of this product or reinstallation.
This warranty is void if this product is installed improperly or in an improper
environment, overloaded, misused, opened, abused, or altered in any manner,
or is not used under normal operating conditions or not in accordance with
any labels or instructions. There are no other or implied warranties of any
kind, including merchantability and fitness for a particular purpose, but if any
implied warranty is required by the applicable jurisdiction, the duration of any
such implied warranty, including merchantability and fitness for a particular
purpose, is limited to two years. Leviton is not liable for incidental, indirect,
special, or consequential damages, including without limitation, damage to,
or loss of use of, any equipment, lost sales or profits or delay or failure to
perform this warranty obligation. The remedies provided herein are the
exclusive remedies under this warranty, whether based on contract, tort or
otherwise.

For Technical Assistance Call:

1-800-824-3005 (U.S.A. Only)

1 800 405-5320 (Canada Only)

www.leviton.com

DI-000-HCCUR-00A

16

DI-000-HCCUR-00A

7/5/02, 2:19 PM

16