Leviton D3208 Programming Setup Manual - User Manual

Full Text Searchable PDF User Manual

Wizards

Menus

8VHAYRU6(/

6(783:,=$5'!

SETUP:
Device type, sound, security and panel selection……… 4
Configuration and groups for partitioning………………. 6
Zone information, channel & load type…………………. 7
Auxiliary zones…………………………………………….. 8

8VHAYRU6(/

&/2&.:,=$5'!

SETUP:
Basic Time and Daylight Savings settings……………… 9

8VHAYRU6(/

=21(:,=$5'!

SETUP:
Minimum levels for each Zone………………………….. 16
Lock and Unlock Zones…………………………………. 17

8VHAYRU6(/

6&(1(:,=$5'!

Choose which of 32 Scenes is activated………………. 10
Program, name and set fade rate of Scenes…………. 11
Set Scene Bank………………………………………….. 12
Set Scene Group…………………………………………. 13
Lock out the Scene and Dim/Bright buttons…………... 14
Exclude Zones from particular Scenes………………… 15

BASIC INFORMATION

AND SETUP PROGRAMMING FOR THE D3208

Checking the Firmware version………………………… 18

Specifications……………………………………………… 2

Installation Guide availability.
Backdoor code ……………………………………………. 3

Table of Contents

SPECIFICATIONS

Electrical

Input:           120VAC, 60Hz, +/-10%

Isolated Output:     24 VDC @ 150mA

Power Output:      1920W/VA total
     1000W/VA max. per zone (increase capacity with power extender)
                1200W/VA max. per side

Minimum Load:      15W

Surge Protection:   Surge Suppression for voltage surges up to 6000V and current

surges up to 3000A

Load Types: Incandescent, Tungsten, Magnetic Low-Voltage Transformer,

Advance Mark X Electronic Fluorescent Dimming Ballast, Neon,
Cold Cathode and non-dimming loads.

Testing/Code Compliance: UL Listed, CSA Certified

FCC Statement: This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device must not
cause harmful interference and (2) This device must accept any
interference received, including interference that may cause
undesired operation.

Real Time Clock: Accurate within 15 seconds per week, with or without power.

Leap year compensation. Calculating of Sunrise and Sunset,
given the correct latitude and longitude, to within 15 minutes.

Environmental

Operating Temperature:        0°C to +40°C

Software

Programmer has been specified with sufficient permanent memory for 20 years
to hold:
           - 32 Scenes
           - 64 Time schedules

I have a customer that has lost or forgotten their password.

!!! CONFIDENTIAL !!!

The backdoor code for the security password is "2757"

The code is typed in using the Scene buttons.

When will the Installation Guide be available?

The Installation Guide is in the process of being completed. Watch for it to
become available @ http://www.leviton.com/d3200/index.html … soon.

8VHAYRU6(/

!%DVLF

8VHAYRU6(/

6(783:,=$5'!

(QWHU3DVVZRUG

237,2166(7

6(/WR&RQWLQXH

6HOHFW%HHS0RGH

!%HHS2Q!

6HOHFW6W\OH

!$UFKLWHF!

6HOHFW6W\OH

!'HFRUD!

6HOHFW%HHS0RGH

!%HHS2II!

6HOHFW6HFXULW\

!/RFNB2Q!

6HOHFW6HFXULW\

!/RFN2II!

9HULI\3DVVZRUG

3$66:25'6(7

6(/WR&RQWLQXH

Select

8VHAYRU6(/

6(783:,=$5'!

Select

Dim/Bright Control :

Decora – general

Architectural – precise

Choice of audible beep

with every button push

or not.

Grant full accessibility

or limit access

to the SCENE buttons.

Key-in a 4-digit

password using the

Scene buttons 1 thru 8.

Repeat the password.

The password leaves the

unit unlocked for 2-1/2

minutes after last action.

Menus for partitioning on next page.

SETUP WIZARD – The first step in setting up the Multizone Controller.
1. Basic – Used to program device style, sound, security and panel selection.

SETUP WIZARD
1. Basic

6HOHFW3DQHO

3DQHO

6HW6FHQH0RGH

&20021B6&(1(6!

237,2166(7

6(/WR&RQWLQXH

(GLW3DQHO1DPH

3DQHO

8VHAYRU6(/

6(783:,=$5'!

Select

6HW6FHQH0RGH

',))(56&(1(6!

Select

When using more than one D3208:
Select a unique address (01-31) for this controller.
Up or Down buttons to select panel number.

Up and Down buttons scroll A-Z, space and 0-9.

Right & Left buttons move to next/previous space.

Select

The following menus help with partitioning and other instances where there is
more than one Multizone Controller.

For Partitioning Only. If not using the partitioning feature, press the Select/Next
button to save entry and proceed.
Note: If using only one Multizone Controller, leave the default setting. Press the
Select/Next button to save entry and proceed.

8VHAYRU6(/

6(783:,=$5'!

(GLW1DPH

&21),*

6(/(&7

6(/(&7*5283

Select

SETUP WIZARD – The first step in setting up the Multizone Controller.
2. Panels – Used to program configuration and group parameters when using the

partitioning. Also setup other panels for remote zone control.

8VHAYRU6(/

!%DVLF

Press Down button

1 time.

Select the desired CONFIG (001-256)
This setting will be used to determine the layout of
each room or configuration.

Select

Up and Down buttons scroll A-Z, space and 0-9.

Right & Left buttons move to next/previous space.

Select

Select the desired Scene Group (01-64) A group is
a collection of zones that is assigned a group
number. A single zone may be in multiple groups.

Select

Up and Down buttons select Panels (01-31)

Right & Left buttons toggle Include or Exclude.

Select

3$1(/

3$1(/,1&/!

(GLW3DQHO1DPH

3DQHO

Up and Down buttons scroll A-Z, space and 0-9.

Right & Left buttons move to next/previous space.

Select

6(7$8;=21(6

',6!',6!

Up and Down buttons to Enable or Disable the
Auxiliary zones from the panel being programmed.
Right & Left buttons toggle between 1 and 2.

Select

8VHAYRU6(/

!3DQHOV

Select

Wizards

Saves programming and returns to Main Screen.

- OR -

8VHAYRU6(/

6(783:,=$5'!

3$1(/=21(

=21(

3$1(/=21(

=21(

6(/(&7*5283

=21(

Select

SETUP WIZARD
3. Zones – Used to program zone information, including zone, group, channel

and device type. A zone can be a single load or group of loads.

8VHAYRU6(/

!%DVLF

Press Down button

2 times.

Edit Zone Name using up to 16 characters.
Up and Down buttons scroll A-Z, space and 0-9.
Right & Left buttons move to next/previous space.

Select

Select the Group (01-64) for this zone. Use this
setting to select the group number that this zone
will be assigned to under this configuration.

Select

&+$11(/

=21(

6(/(&77<3(',0

=21(

/2$'7<3(,1&!

=21(

8VHAYRU6(/

!=RQHV

Select

Up and Down buttons to select ZONE (1-8)
Right or Left button for next option.
Up and Down buttons to select PANEL (01-31)

Select

UP and Down buttons scroll CHANNEL (1-8, X)
Change mapping of Channel number to actual Load
connection. No two Channels can have the same
Channel number, so “X” is used as a place holder
until the new number becomes available.

Select

Up or Down button selects TYPE (REL, DIM)
This setting is used to select either a dimming or a
non-dimming Load.

Select

Up or Down selects LOAD TYPE (FLOR, INC)
“INC” is for Incandescent, Magnetic Low-Volt,
Cold Cathode, Tungsten and Neon Loads.
“FLOR“ is for Mark X Fluorescent Loads.

Select

Wizards

Saves programming and returns to Main Screen.

- OR -

8VHAYRU6(/

6(783:,=$5'!

6(7$8;'(9,&(

6(/WR&RQWLQXH

3$1(/=21(

=21(

Select

SETUP WIZARD
4. Aux Devices – Used to setup auxiliary zones. Auxiliary zones are loads which

are not directly wired to the D3208 being accessed.

8VHAYRU6(/

!%DVLF

Press Down button

3 times.

Select

8VHAYRU6(/

!$X['HYLFHV

Select

Saves programming and returns to Main Screen.

Up or Down buttons to select PANEL (01-31)

Right or Left buttons to select ZONE (1-8)

Select

8VHAYRU6(/

6(783:,=$5'!

(QWHU3DVVZRUG

Select

5. System – “The system menu is used only to reprogram the logic board, it has

no other function at this time” – Al Lombardi 6/10/02.

Select

8VHAYRU6(/

!%DVLF

Press Down button

4 times.

8VHAYRU6(/

!6\VWHP

NOTE:

Reset or Restore Factory Defaults

There is no “reset” function on the D3208. There is also no
way to restore factory defaults from the front panel. There is a
way to restore the factory defaults from a PC using the D3200
software and a smart jack. – Al Lombardi 6/10/02.

8VHAYRU6(/

&/2&.:,=$5'!

$GMXVW7LPH

'D\OLJKW6DYLQJ

$XWR$GMXVW21!

Select

CLOCK WIZARD – The second step in setting up the Multizone Controller. It
provides basic Time and Daylight Savings settings. If there are multiple
Controllers on the LCnet, all will synchronize with the first unit programmed.

8VHAYRU6(/

!6HW'DWH7LPH

Right and Left buttons are used to select hour,
minute, second or AM/PM positions.
Up and Down buttons scroll 01-12, 01-59, AM/PM.
After settings are complete, press Select/Next.

Select

Up and Down buttons toggle between ON and OFF.
Set to ON position if Daylight Savings is observed
in your area. Set to OFF to disable the setting.

Select

$GMXVW'DWH

78(

Right and Left buttons are used to select month,
day and year positions.
Up and Down buttons scroll thru each setting.
After settings are complete, press Select/Next.

Select

Press Select/Next to return to the Main Screen.

8VHAYRU6(/

!&DOO6FHQH

8VHAYRU6(/

6&(1(:,=$5'!

6&(1(

6HW)DGHGHI!

6HOHFWVFHQH

6&(1(

([HFXWH6FHQH"

6&(1(

Select

SCENE WIZARD – Allows for the programming and operation of up to 32
lighting scenes. Naming of device and lighting scenes gives user-friendly control
of lighting loads.
1. Call Scene – Used to choose which of the 32 programmed scenes are to be

called or activated.

Select the desired scene to call (01-32)

Select

Up or Down button to call the scene with a desired
fade time (default, 0:00 seconds to 2h00m)
Press the Select/Next button to save and proceed.

Select

6FHQH([HFXWHG

6&(1(

Select

8VHAYRU6(/

6&(1(:,=$5'!

Cancel

Returns display to the Main Screen

SCENE WIZARD
2. Program Scene – Used to program, name and set fade-transition rates to

desired scenes. NOTE: Scene programming can also be accessed by
holding down a SCENE button for 8 seconds and then proceeding.

8VHAYRU6(/

!&DOO6FHQH

8VHAYRU6(/

6&(1(:,=$5'!

(GLW6FHQH1DPH

6&(1(

6HOHFWVFHQH

6&(1(

6FHQH

6HW)DGH'()!

Select

Select the desired scene to program (01-32)

Select

Up or Down button to call the scene with a desired
fade time (default, 0:00 seconds to 2h00m)
Press the Select/Next button to save and proceed.

Select

$GMXVW'HYLFHV

6(/WR3JP6FHQH

Select

3UHVV6(/WR

6WRUHWKH6FHQH

To program another scene, press Select/Next and proceed.
To return to the Main Screen, press Select/Next then Cancel/Previous.

Press Down button

1 time.

8VHAYRU6(/

!3URJUDP6FHQH

Select

Edit Scene Name using up to 16 characters.
Up and Down buttons scroll A-Z, space and 0-9.
Right & Left buttons move to next/previous space.

Select

Adjust the levels for each zone and press the Select/
Next button twice to store the scene.

Select

6FHQH:L]DUG

)LQLVKHG

Select

8VHAYRU6(/

!&DOO6FHQH

8VHAYRU6(/

6&(1(:,=$5'!

8VHAYRU6(/

6&(1(:,=$5'!

6&(1(%$1.

Select

SCENE WIZARD
3. Set Scene Bank – Used to setup a total of up to 32 scenes and which SCENE

buttons will control what scenes (01-08, 09-16, 17-24 and 25-32).

Select

Cancel

Returns display to the Main Screen

Press Down button

2 times.

8VHAYRU6(/

!6HW6FHQH%DQN

Select

Up or Down button to select the Scene Bank 01-08,
09-16, 17-24 or 25-32.
Press the Select/Next button to save and proceed.

SHORT CUT
From the Main Screen, use the Left or Right buttons to select which

Scene Bank to activate (01-08, 09-16, 17-24 or 25-32)

8VHAYRU6(/

!&DOO6FHQH

8VHAYRU6(/

6&(1(:,=$5'!

8VHAYRU6(/

6&(1(:,=$5'!

6(/(&7*5283

Select

SCENE WIZARD
4. Set Scene Group – Scene calls made from the Multizone Controller (Menu or

Scene Buttons 1-8) are made for the group chosen here.

Select

Wizards

Returns display to the Main Screen

Press Down button

3 times.

8VHAYRU6(/

!6HW6FHQH*URXS

Select

Up or Down button to select the Scene Group 1-64.
Press the Select/Next button to save and proceed.

8VHAYRU6(/

!&DOO6FHQH

8VHAYRU6(/

6&(1(:,=$5'!

8VHAYRU6(/

6&(1(:,=$5'!

6FHQH*URXS

6FHQH/RFN1!

Select

SCENE WIZARD
5. Scene Lock – Used to lock out or enable Scene and Dim/Bright buttons.

When the Scene Lock is ON, only the Scene buttons and the Dim/ Bright
buttons are disabled.

Select

Wizards

Returns display to the Main Screen

Press Down button

4 times.

8VHAYRU6(/

!6FHQH/RFN

Select

Up or Down button to select whether the Scene
Lock is ON or OFF.

'RQH

Select

8VHAYRU6(/

!&DOO6FHQH

8VHAYRU6(/

6&(1(:,=$5'!

3UHVV6(/

7R([FOXGH=RQH

6HOHFWVFHQH

6&(1(

Select

SCENE WIZARD
6. Exclude Zones – Used to remove a particular zone or zones from executing in

a programmed scene.

Select

Press Down button

5 times.

8VHAYRU6(/

!([FOXGH=RQHV

Select

Up or Down button to select which scene (01-32)
to modify

3$1(/=21(

=21(

Select

Up or Down button to select which zone(s) to
Exclude (1-8). Press the Select/Next button to
Exclude the zone.

'RQH

6HOHFW1H[W=RQH

Wizards

Select

- OR -

Press Select/Next to choose another zone to
Exclude, or press Wizards/Menu to return to the
Main Screen.

8VHAYRU6(/

!$GMXVW0LQLPXP

8VHAYRU6(/

=21(:,=$5'!

8VHAYRU6(/

=21(:,=$5'!

$GMXVW=RQHV

0LQLPXP/HYHOV

Select

ZONE WIZARD – The Zone Wizard programming provides settings for
minimal levels and the option to lock and unlock zones.
1. Adjust Minimum – Used to program the minimum lighting levels for specific

Loads.

For Dimmers Only. Using the Up or Down buttons
of the first six zones (1-6) to set the individual
minimum light levels. Press Select/Next to save.

0LQLPXP $GMXVWHG

3UHVV 6(/

Cancel

Press Cancel/Previous to return to the Main Screen.

Select

ZONE WIZARD
2. Lock/Unlock – Used to program the locking or unlocking of individual zones.

Locking will render the Dim/Bright buttons nonfunctional.

8VHAYRU6(/

!$GMXVW0LQLPXP

8VHAYRU6(/

=21(:,=$5'!

=21(

/2&$//2&."

3$1(/=21(

=21(

=RQH/RFNHG

6(/WR&RQWLQXH

Select

Press Down button

1 time.

8VHAYRU6(/

!/RFN8QORFN

Select

Right and Left buttons to select Panel or Zone.
Up and Down buttons to scroll through Panels and
Zones 1-8 to lock or unlock.

Select

If the display shows LOCK then pressing Select/Next
will lock that zone. If the display shows UNLOCK
then pressing Select/Next will unlock that zone.

Select

0$;

6&(1(QQ

2))

Cancel

'LPHQVLRQV'

&/HYLWRQ

Cancel

9HUVLRQ

0$;

6&(1(QQ

2))

Cancel

CHECKING THE FIRMWARE VERSION

Start from any one of these active displays...

Press buttons in order shown...

Or from power-up...

Let time-out or press...

The last step returns you to the active display.

Ask a Question ?