Full Text Searchable PDF User Manual
Auto Levelling Rotating Laser
and Electronic Receiver
Rotation Speed & Side Mount
Vertical Operation & Specifications
Laser output sign lies near the output aperture.
Do not stare directly into laser beam.
Do not disassemble the instrument or attempt to
perform any internal servicing. Repairs and service
should be performed only authorised service
centres of Redback Lasers.
This instrument complies with the safety
Classification standards of laser radiation.
CAUTION: Class II laser <1mW at 635nm.
Do NOT stare into laser beam or aim at
Follow relevant Australian Standards
AUTO1™ Included Accessories
AUTO1™ Laser Unit
Protective Carry Case
Standard “AA” Batteries
LR700 Electronic Receiver
Receiver Staff Clamp
Side Mount Bracket (wall mount)
Copyright © CMI LasersTM RedBack lasersTM and Level1LasersTM . All rights reserved CMI Industries Pty Ltd 2012
No artwork or photographs produced by CMI Industries Pty Ltd may be used copied or reproduced without the written consent
from CMI Industries Pty Ltd
1. Control Panel
2. Dot Laser Output
3. Rotating Laser Output
4. Pendulum Lock
5. Vial for Vertical Rotation Mode
6. DC Input (optional Power Supply)
7. Battery Compartment 6x “AA”
8. Tripod 5/8”-11tpi Mount
5/8” – 11tpi Screw
Place laser on Tripod or on a stable surface, rotate the pendulum locking
knob to the un-locked position (marked as “ON”) then press the power
button on the control panel. The laser will auto level, the laser head will
rotate and emit a laser beam.
The AUTO1 operates on 6 x standard Alkaline “AA” batteries, simply un-
screw the battery compartment where indicated and insert batteries in the
Turning Laser On For Levelling
Rotation Speed Selection
Turning Laser On For Levelling
has three rotation speeds (Low, Medium and High), under
normal conditions high speed is recommended when using the LR700
electronic receiver. If you are using the laser indoors visibly a slower rotation
speed may increase the visibility of the line produced.
Rotation speed is changed by pressing the speed button on the control panel
an LED light will indicate the selected speed, further presses of this button
wil toggle between the three available speeds.
The Side Plate can be used in two ways; firstly as a wall mount in horizontal
levelling mode and secondly as a side mount for vertical rotation mode.
The plate clips onto the bar at the back of the AUTO1 laser and is removed
by pressing the attachment level.
Side Mount Plate
Vertical Rotation Mode
can be placed on its side with the side mount plate attached
and used for vertical rotation, this can be handy for any indoor vertical
alignment off the rotating beam.
To operate the AUTO1 in vertical rotation mode DO NOT unlock the pendulum,
leave it in the “OFF” position, use the adjustment screw on the side mount to
level off the bubble vial on the AUTO1. Once the bubble is central in the vial
press the power button on the laser and the laser head will begin to rotate,
the rotating beam being a vertical line and the dot beam being level.
Another application where the vertical mode can be usefull is site squaring
by aligning the dot laser beam along one axis of the 90 degree square and
then using the receiver to pick up the rotating beam which is at 90 degrees
to the dot laser beam.
Range with LR700 Receiver
Self Levelling Range
IP Dust Water Resistance
C to +40
6 x “AA” Alkaline
Power LED Flash
The LR700 is an electronic laser receiver/detector and comes with a staff
clamp bracket which allows you to attach the receiver to a measuring staff.
Power up by pressing the power button, hold the receiver so the reception
window is facing the rotating laser (upright for horizontal and on its side
for vertical rotation). When the reception window is level with the rotating
beam the LED indication lights and Sound will alert you, When the laser
beam is absolutely level with the receiver the central green LED is illuminated
the red LED’s above and below indicate when the laser beam is just above or
below the central line on the receiver.
The Bubble vial will help you hold the receiver and staff vertical when taking
readings. The line on the staff clamp lines up with the level mark on the
receiver. Note that the receiver only works on the rotating beam and not the
dot, and that high speed rotation tends to work better than medium or slow.
LR700 Receiver operation
12 Month WARRANTY - LEVEL 1 LASERS
Level 1 Lasers
distributed by CMI Industries Pty Ltd
P.O. Box 7324 - Geelong West - Victoria - 3218 - Australia
Ph: (03) 5228 0796 email: firstname.lastname@example.org
CMI Industries Pty Ltd provides consumers with a warranty to our products, this is in addition to
requirements of any relevant legislation such as the Competition and Consumer Act 2010. Definitions:
“CMI”, “We” or “Our” “Level1Lases” refers to CMI Industries Pty Ltd (ABN 29 102 713 922) of 8 Autumn
St, Geelong West, Victoria 3218 ph (03) 5228 0777
“You” or “Consumer” refers to the initial purchaser of the product.
“Product” refers to goods manufactured by or for CMI Industries Pty Ltd under the brand of
“Material” refers to material or component used in the construction and manufacture of the product.
“Workmanship” refers to handling, assembly and manufacturing processes done by or for CMI
Industries Pty Ltd in order to manufacture the products.
“Warranty Period” For Level1Laser Products is
. Warranty period is from original purchase
date, no extension is made in the event of warranty replacement products supplied or time spent being
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are
entitled to a replacement or refund for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods
fail to be of acceptable quality and the failure does not amount to a major failure.
CMI warrants that our products will be free from defects in material and workmanship for the warranty
CMI promises to repair or replace, free of charge, the product or part of product if found to be faulty
due to defective workmanship or materials within the duration of the warranty as long as the following
terms and conditions are met;
• Product must not have been misused or abused, must not have incurred accidental damage or had
un-authorised repair or tampering that has caused or contributed to its fault or failure.
• You must contact CMI by phone, mail or email immediately when a fault or defect has become
apparent and within the warranty period.
• Product must be returned to store of purchase or directly to CMI, we will cover cost of postage only
when sent by our reply paid Australia Post service (Australian Main land and Tasmania only) details will
be provided upon phone, post or email communications with us.
• CMI will cover cost of freight back of repaired or replaced product to original purchase store or you
directly (depending on how it was sent Australian Main Land and Tasmania only).
• CMI will determine whether to repair or replace the product or part of product on a case by case
• Further exclusions in this warranty include damage or defect caused by use of non-original
accessories or parts, damage in transportation, normal wear and tear, damage through moisture,
damage due to electric surge, failure due to neglect or damaged caused by adjustments not outlined in
Subject to the requirements of all applicable Australian Acts or legislation and to the extent permitted
by law, CMI accepts no liability (whether expressed or implied) of any nature whatsoever for any loss
of earnings, hiring of replacement equipment, Inaccurate work carried out by the consumer or agent,
damage or injury arising as a result of any fault in the product. It is the consumers responsibility to
maintain good working practices and regularly test their tools for accuracy and serviceability.
Calibration of the product is not covered by warranty subject to the requirement of all applicable
Australian Acts or legislation and to the extent permitted by law,
A CMI product returned that fails to fall within the terms and conditions of this warranty will be quoted