PDF User Manual

  1. Home
  2. Manuals
  3. LG Colour Television Owner's Manual

LG Colour Television Owner's Manual

Made by: LG
Type: Owner's Manual
Category: TV
Pages: 13
Size: 0.08 MB

 

Download PDF User Manual



Full Text Searchable PDF User Manual



background image

Colour Television

OWNER'S MANUAL

Please read this manual carefully before operating
your set. 
Retain it for future reference.
Record model number and serial number of the set. 
See the label attached on the back cover and quote
this  information to your dealer when you require
service.

Model number

:

Serial number

:

P/NO : 3828VA0159H-2/2 (PC81A, 009K/017N TX, EN)

 


background image

Installation

Connection of external equipment

Power

This set operates on an AC mains supply, the voltage is as indicated on the label
on the back cover. Never apply DC power to the set. In the event of thunderstorms
or powercuts, please pull out the aerial and mains plugs.

Warning

To prevent fire or shock hazard, do not expose the set to rain or moisture.

Service

Never remove the back cover of the set as this can expose you to very high
voltage and other hazards. If the set does not operate properly, unplug it and call
your dealer.

Aerial

Connect the aerial cable to the socket marked 

+

75

¥

on the back cover. For the

best reception an outdoor aerial should be used.

Location

Position your set so that no bright light or sunlight falls directly onto the screen.
Care should be taken not to expose the set to any unnecessary vibration, moisture,
dust or heat. Also ensure that the set is placed in a position to allow a free flow of
air. Do not cover the ventilation openings on the back cover.

Battery installation

The remote control handset is powered by two AA type batteries. Gently pull down
the cover of the remote control handset until the battery compartment is exposed.
Install two batteries as indicated by the polarity symbols (

§]

and 

§^

) marked inside

the compartment. 

Note : To avoid damage from possible battery leakage, remove the batteries if you
do not plan to use the remote control handset for an extended period of time.

You can connect additional equipment, such as VCRs, camcorders etc. to your set.

Aerial socket

1.  Connect the RF out socket of the VCR to the aerial socket on the back of the set.
2.  Connect the aerial cable to the RF aerial in socket of the VCR.
3 . Store the VCR channel on a desired programme number using the 'Manual

programme tuning' section.

4.  Select the programme number where the VCR channel is stored.
5.  Press the PLAY button on the VCR.

Euro scart socket

1.  Connect the Euro scart socket of the VCR to the Euro scart socket of the set.
2.  Press the PLAY button on the VCR.

If your VCR outputs a switching voltage connect to Euro scart socket. If 

Auto

AV On 

is selected, the set will switch to AV 1 (AV) mode automatically. 

Otherwise press the TV/AV button on the remote control handset to select 

AV

1  

(

AV

). The VCR playback picture appears on the screen.

You can also record programmes received by the TV on video tape.

Audio/Video in sockets (option)

1.  Connect the audio/video out sockets of the VCR to audio/video in sockets of

the set.

2.  Press the TV/AV button to select 

AV 2

3.  Press the PLAY button on the VCR.

The VCR playback picture appears on the screen.

Headphone socket (option)

In some models which have a headphone sockets can perform this function.
Insert the headphone plug to the headphone socket on the front panel. You can
listen to the sound  through the headphone. To adjust the headphone volume,

press the 

¢‚/¢”

button. If you press the 

W

W

button, the sound from the headphone

is switched off.

 


background image

Location and function of controls

1

PR.LIST

2

3

4

5

6

7

8

0

OK

PR

VOL

VOL

PR

9

MENU

SLEEP

ARC

TV/AV

PSM

Q.VIEW

1

10

6

12

16

14

8

11

15

2

All the functions can be controlled with the
remote control. Some functions can also be
adjusted with the buttons on the front panel of
the set.

Remote control handset

Before you use the remote control handset,
please install the batteries.

1.  POWER 

switches the set on from standby or off to
standby.

2.  MUTE

switches the sound on or off.

3.  NUMBER BUTTONS

switch the set on from standby or directly
select a number.

4.  NO FUNCTION

5.  NO FUNCTION

6.  MENU

selects a menu.

7.

TELETEXT BUTTONS (option)
These buttons are used for teletext.
For further details, see the Teletext
section.

8.

Q.VIEW
return to the previously viewed
programme.

9.  NO FUNCTION

10.  TV/AV

selects TV or AV mode.
clears the menu from the screen.
switches the set on from standby.

11.  ARC (Aspect Ratio Control)

change the picture format.

12. PSM (Picture Status Memory)

recalls your preferred picture setting.

13.  NO FUNCTION

14.

¡ª/¡

(Programme Up/Down)

selects a programme or a menu item.
switches the set on from standby.

¢‚/¢”

(Volume Down/Up)

adjusts the volume.
adjusts menu settings. 
OK
accepts your selection or displays the
current mode.

15. SLEEP

sets the sleep timer.

16. PR. LIST

displays the programme table.

17. VCR BUTTONS (option)

control a LG video cassette recorder.

COLOURED BUTTONS

These buttons are used for teletext (only
TELETEXT models) or programme edit.

TV/AV

PSM

TEXT MENU

1

2

3

4

5

6

7

8

9

0

OK

PR

PR

VOL

VOL

Q.VIEW

MIX

TIME REVEAL

SIZE

HOLD UPDATE INDEX

ARC

SLEEP

PR.LIST

SSM/

MODE

M

T

X

T

EYE

SP/LP ON/OFF

CH+

REW

PLAY

FF

CH

P/STILL

STOP

REC

2

3

4

1

5

6

7

8

9

10

11

12

13

14

15

16

17

3

With TELETEXT

Without TELETEXT

 


background image

Basic operation

On and off

1.

Press the main power button to switch the set on.

2.

If the set is in standby mode, press the 

r

¡ª/¡

TV/AV or NUMBER buttons

on the remote control handset to switch it on fully. 

3.  Press the 

r

button on the remote control handset. 

The set reverts to standby mode. 

4.

Press the main power button again to switch the set off. 

Note : If, while the set is switched on, the mains plug is disconnected the set will
switch to standby or power on when the mains plug is replaced in the mains power
socket.

Programme selection

You can select a programme number with the 

¡ª/¡

or NUMBER buttons.

Volume adjustment

Press the 

¢‚/¢”

button to adjust the volume.

Mute function

Press the 

W

W

button. The sound is switched off and the display 

W

W

appears. 

You can cancel it by pressing the  

W

W  

 

or 

¢‚/¢”

button.

Quick view

Press the Q.VIEW button to view the last programme you were watching.

On screen language selection

The menu can be displayed on the screen in desired language. First select your
language.

1.

Press the MENU button to select the Station menu.

2.

Press the 

¡ª/¡

button to select 

Language

3.

Press the OK button.

4.

Press the 

¡ª/¡

or 

¢‚/¢”

button to select your desired language.

5.

Press the OK button. 
All the on screen displays will appear in the selected language.

6.

Press the TV/AV button to return to normal TV viewing. 

Front panel 

Shown is a simplified representation of front panel. Here shown may be
somewhat different from your set.

v

v  

 

r

r  

   

  y

y

MENU    OK   

¢‚

VOL

¢” ¡

PR

¡ª

VIDEO    AUDIO   

18

14

21

19 20

6

22

Location and function of controls

18. MAIN POWER

switches the set on or off.

19. POWER/STANDBY INDICATOR

illuminates brightly when the set is in standby mode.
dims when the set is switched on.

20. REMOTE CONTROL SENSOR

21. AUDIO/VIDEO IN SOCKETS (AV2) (option)

Connect the audio/video out sockets of external equipment to these sockets.

22. HEADPHONE SOCKET (option) 

Connect the headphone plug to this socket.

POWER

AV2

 


background image

The dialogue between you and your set takes place on screen with an operator
menu. The buttons required for the operating steps are also displayed.

Menu selection

1.

Repeatedly press the MENU button to display each menu.

2.

Press the 

¡ª/¡

button to select a menu item.

The selected menu item changes from green to purple.

3.

Press the 

¢‚/¢”

button to change the setting of a menu item or OK button to

display the sub menu.

Note : 
a.  In the AV mode, the Station menu is not displayed.
b.

In the teletext mode, menus are not displayed.

c.

In some models, the 

System BG

or 

will not display in the 

Auto

or

Manual

programme

menu.

d.

In some models, the 

Game

will not display in the Special menu.

On screen menus

Station menu

Picture menu

Special menu

TV programme

Auto 

O

programme

Manual

O

programme

Program me

O

edit

Language

()

OK

MENU

TV®AV

System

BG

Storage 

O

from

1

Start

()

O

}{

OO

MENU

O

TV®AV

Input

O

TV

Child

O

lock

O

Off

Auto

O

sleep

O

Off

AVL

Off

Blue  back

Off

Game
()

O

}{

O

OK

O

MENU

O

TV®AV

O

Contrast

63

'

O

Brightness

31

·

O

Colour

31

O

Sharpness

31

()

O

}{

O

OK

O

MENU

O

TV®AV

System

BG

Channel

V®UHF

20

Fine

{{{

Search

OOOOOO

Name

C

20

Auto  AV

Off

Storage

1

()

O

}{

O

OK

O

MENU

O

TV®AV

0

ARD

5

ARD1

1

FDZ

6

FDZ1

2

C12

7

C12

3

S4

8

S44

4

CH

-

5

9

CH

-

5

}{

Delete

Copy

()

Move

Skip

 


background image

Setting up TV stations

Up to 100 TV stations can be stored in this set by programme numbers (0 to 99).
Once you have preset the stations, you will be able to use the 

¡ª/¡

or NUMBER

buttons to scan the stations you programmed.
Stations can be tuned using automatic or manual modes.

Auto programme tuning

All stations that can be received are stored by this method. It is recommended that
you use auto programme during installation of this set.

1.

Repeatedly press the MENU button to select the Station menu.

2.

Press the

¡ª/¡

button to select 

Auto programme

.

3.

Press the OK button to display the 

Auto programme

menu.

Option :
In some models, the display 

System L

or 

DK

(

BG

or 

I

) appears. 

In that case, press the 

¡ª/¡

button to select 

System

then select your local TV

system with the 

¢‚/¢”

button.

L

: SECAM L/L’(France)

DK

: PAL D/K, SECAM D/K (East Europe)

BG

: PAL B/G, SECAM B/G (Europe/East Europe)

I

: PAL I/II (U.K./Ireland)

4.  Press the 

¡ª/¡

button to select 

Storage from

.

5.

Select the beginning programme number with the 

¢‚/¢”

button or NUMBER

buttons. Any number under 10 is entered with a numeric ‘0’ in front of it, i.e. ‘05
for 5.

6.  Press the 

¡ª/¡

button to select 

Start

.

7.  Press the OK button to begin auto programming.

All receivable stations are stored. The station name is stored for stations which
broadcast VPS (Video Programme Service), PDC (Programme Delivery
Control) or TELETEXT data. If no station name can be assigned to a station,
the channel number is assigned and stored as 

C

(V/UHF 01-69) or 

S

(Cable

01-47), followed by a number.
To stop auto programming, press the MENU button. 
When auto programming is completed, the 

Programme edit 

menu appears

on the screen. See the ‘Programme edit’ section to edit the stored programme.

8.  Press the TV/AV button to return to normal TV viewing.

Manual programme tuning

Manual programme lets you manually tune and arrange the stations in whatever
order you desire. Also you can assign a station name with five characters to each
programme number.

1.

Repeatedly press the MENU button to select the Station menu.

2.

Press the 

¡ª/¡

button to select 

Manual programme

3.

Press the OK button to display the 

Manual programme

menu.

Option : 
In some models, the display 

System L 

or 

DK 

(

BG

or 

I

appears. 

In that case, press the 

¡ª/¡

button to select 

System

then select your local TV

system with the 

¢‚/¢”

button.

L

: SECAM L/L’(France)

DK

: PAL D/K, SECAM D/K (East Europe)

BG

: PAL B/G, SECAM B/G (Europe/East Europe)

I

: PAL I/II (U.K./Ireland)

4.

Press the 

¡ª/¡

button to select 

Channel

. Press the 

¢‚/¢”

button to select

V/UHF

or 

Cable 

as required.

5.

Press the 

¡ª/¡

button to select 

Search

. Press the 

¢‚/¢”

button to commence

searching. If a station is found the search will stop. 

6.

If this station is the one required, press the 

¡ª/¡

button to select 

Storage

.

Select the desired programme number with the 

¢‚/¢”

button or NUMBER

buttons. Any number under 10 is entered with a numeric ‘0’ in front of it, i.e.
05’ for 5.

7.

Press the OK button to store it. The display 

Stored

will appear.

8.

To store another station, repeat steps 4 to 7.

Note : If programmed station has poor quality sound, select the system again in
the Manual programme menu.

 


background image

Setting up TV stations

Assigning a station name
1.

Repeat the Manual programme tuning steps 1 to 3.

2.

Press the 

¡ª/¡

button to select 

Name

.

3.

Press the 

¢”

button. You can use a blank, 

+

-

, the numeric 

to 

and the

alphabet 

A

to 

Z

With the 

¢‚

button you can select in the opposite direction.

4.

Select the next position by pressing the OK button and then take your choice
of the second character, and so on. 

5.

Repeat the ‘Manual programme tuning’ steps 6 to 7.

Auto AV setting
If your VCR outputs switching voltage when it is switched to playback, select 

Auto

AV On

with the VCR connected to the Euro scart socket. The set is automatically

switched to AV mode when an AV signal is input. But if you want to keep on
watching TV mode, set 

Auto AV

to 

Off

.

1.

Repeat the ‘Manual programme tuning’ steps 1 to 3.

2.

Press the 

¡ª/¡

button to select 

Auto AV

.

3.

Press the 

¢‚/¢”

button to select 

On 

or 

Off

.

4.

Repeat the ‘Manual programme tuning’ steps 6 to 7.

Press the TV/AV button to return to normal TV viewing.

Fine tuning

Normally fine tuning is only necessary if reception is poor.

1.  Repeat the ‘Manual programme tuning’ steps 1 to 3.
2.

Press the 

¡ª/¡

button to select 

Fine

.

3.

Press the 

¢‚/¢”

button to fine tune for the best picture and sound.

4.

Repeat the ‘Manual programme tuning’ steps 6 to 7.

5.

Press the TV/AV button to return to normal TV viewing. 
The finely tuned programme will be indicated by yellow number during
programme selection.

Calling the programme table

You can check the programmes stored in the memory by displaying the
programme table.

Displaying programme table
Press the PR. LIST button to display the 

Programme table

.

Note :
a.

You may find some blue programmes. They are skipped during auto
programming or in the programme edit mode.

b.

Some programmes with the channel number shown in the programme table
indicate there is no station name assigned.

Selecting a programme in the programme table 
Select a programme with the 

¡ª/¡

or 

¢‚/¢”

button.

Then press the OK button.  
The set switches to the chosen programme number.

Paging through a programme table
There are 10 programme table pages in which contain 100 programmes. 
Pressing the 

¡ª/¡

or 

¢‚/¢”

button repeatedly turns the pages.

Press the TV/AV button to return to normal TV viewing.

 


background image

Setting up TV stations

Programme edit

This function enables you to delete or skip the stored programmes. Also you can
move some stations to other programme numbers or insert a blank station data
into the selected programme number.

1.

Repeatedly press the MENU button to select the Station menu.

2.

Press the 

¡ª/¡

button to select 

Programme edit

.

3.

Press the OK button to display the 

Programme edit

menu.

Deleting a programme 
1.

Select a programme to be deleted with the 

¡ª/¡

or 

¢‚/¢”

button. 

2.

Press the RED button twice. 
The selected programme is deleted, all the following programmes are shifted
up one position.

Copying a programme 
1.

Select a programme to be copied with the 

¡ª/¡

or 

¢‚/¢”

button. 

2.

Press the GREEN button.
All the following programmes are shifted down one position.

Moving a programme 
1.

Select a programme to be moved with the 

¡ª/¡

or 

¢‚/¢”

button. 

2.

Press the YELLOW button. 

3.

Move the programme to the desired programme number with the 

¡ª/¡

button.

4.

Press the YELLOW button again to release this function.

Skipping a programme number 
1.

Select a programme number to be skipped with the 

¡ª/¡

or 

¢‚/¢”

button.

2.

Press the BLUE button. The skipped programme turns to blue.

3.

Press the BLUE button again to release the skipped programme. 
When a programme number is skipped it means that you will be unable to
select it using the 

¡ª/¡

button during normal TV viewing. If you want to select

the skipped programme, directly enter the programme number with the
NUMBER buttons or select it in the programme edit or table menu.

Note : The programme number 01 cannot be skipped.

Press the TV/AV button to return to normal TV viewing.

 


background image

Picture adjustment

Other functions

Picture adjustment

You can adjust picture contrast, brightness, colour intensity and sharpness  to the
levels you prefer.

1.

Repeatedly press the MENU button to select the Picture menu.

2.

Press the 

¡ª/¡

button to select the desired picture item.

3.

Press the 

¢‚/¢”

button to make appropriate adjustments.

4.

Press the OK button to store it for the picture 

User

.

To recall your preferred setting, press the PSM button until the desired picture
(

Dynamic

Mild

Standard

or 

User

) appears. The picture 

Dynamic

Mild

and

Standard

are programmed for good picture reproduction at the factory and cannot

be changed.

Picture format

You can watch the TV in various picture formats; Standard, Wide or Zoom.

Repeatedly press the ARC button to select your desired picture format.

Standard

This picture format is 4 to 3 of general TV.

Wide

You can enjoy the cinema (the picture format of 16:9) or general TV programme
through the 16:9 mode. 
The screen 16:9 is viewed just like that but the screen 4:3 is magnified to the left
and right so that the screen 16:9 is full.

Zoom 

You can enjoy the cinema in a vast screen through the Zoom mode. 
The screen 4:3 is magnified to the upper/lower and left/right sides so that the
screen 16:9 is full. The bottom and top of the picture may be lost.

Note :
a.  When you switch the set to standby or off, the 

Wide

or 

Zoom

picture format is

reset to the 

Standard

(4:3).

b.

In the manual AV mode, 

Wide

picture format is not available.

TV and AV modes

Inputs can be set for TV or AV mode. AV mode is used when a video cassette
recorder (VCR), or other equipment is connected to the set.

Note : When a VCR is connected via the aerial socket the set is used in TV mode.
See the ‘Connection of external equipment’ section.

1.  Repeatedly press the MENU button to select the Special menu.
2.

Press the 

¡ª/¡

button to select 

Input

.

3.

Press the 

¢‚/¢”

button to select

TV

AV 1 

(

AV

or 

AV 2

.

The two AV modes are :
AV1 (AV) : VCR connected to the Euro scart socket on the back
AV2          : VCR connected to the AV2 sockets on the front panel (option)
In some models, AV 2 (and Audio/Video in sockets) is an optional function.
Only a set with the AV 2 (and Audio/Video in sockets) can perform this
function.

Alternatively you can select the TV or AV mode by pressing the TV/AV button.

Auto sleep

If you select 

Auto sleep On

the set will automatically switch itself to standby mode

approximately ten minutes after a TV station stops broadcasting.

1.  Repeatedly press the MENU button to select the Special menu.
2.

Press the 

¡ª/¡

button to select 

Auto sleep

.

3.

Press the 

¢‚/¢”

button to select 

On

.

4.

Press the TV/AV button to return to normal TV viewing. 

 


background image

Child lock

The TV can be set so that the remote control handset is needed to control it. This
feature can be used to prevent unauthorized viewing.

1.  Repeatedly press the MENU button to select the Special menu.
2.

Press the 

¡ª/¡

button to select 

Child lock

.

3.

Press the 

¢‚/¢”

button on the remote control handset to select 

On

.

4.

Press the TV/AV button to return to normal TV viewing. 

With the lock on, the display 

Child lock on

appears on the screen if any button on

the front panel is pressed while viewing the TV.

Note : The display 

Child lock on

not appears on the screen if any button on the

front panel is pressed while displaying the menus.

AVL (Auto volume leveler)

If you select 

AVL On

, the set automatically keeps on an equal volume level even if

you change programmes.

1.  Repeatedly press the MENU  button to select the Special menu.
2.

Press the 

¡ª/¡

button to select 

AVL

.

3.

Press the 

¢‚/¢”

button to select 

On

.

4.

Press the TV/AV button to return to normal TV viewing. 

Blue back

If you have set 

Blue back On

, the blue background appears on the screen when

there is no or poor signal.

1.  Repeatedly press the MENU button to select the Special menu.
2.

Press the 

¡ª/¡

button to select 

Blue back

.

3.

Press the 

¢‚/¢”

button to select 

On

.

4.

Press the TV/AV button to return to normal TV viewing.

Sleep timer

You don’t have to remember to switch the set off before you go to sleep. The sleep
timer automatically switches the set to standby after the preset time elapses.
Press the SLEEP button to select the number of minutes. The display 

r

r

--- will

appear on the screen, followed by 

10

,

20

30

60

90

120

,

180 

and 

240 

The timer

begins to count down from the number of minutes selected.

Note : 
a.

To view the remaining sleep time, press the SLEEP button once.

b.

To cancel the sleep time, repeatedly press the SLEEP button until the display

r

r

--- appears.

c.

When you switch the set off, the set releases the preset sleep time.

Game (option)

The game is an optional function. Only a set with Game option can perform this
function. 

1.

Repeatedly press the MENU button to select the Special menu.

2.

Press the 

¡ª/¡

button to select 

Game

.

3.

Press the OK button to start the game.
Press the 

¢‚/¢”

and 

¡ª/¡

buttons to move and tilt the gun to the left and right.

Press the OK button to fire the gun or to continue the game. The game score
are displayed on the screen.

4.

Press the TV/AV or MENU button to return to normal TV viewing. 

Other functions

 


background image

Teletext (or TOP text) is an optional function, therefore only a set with the teletext

system can receive the teletext broadcast.

Teletext is a free service broadcast by most TV stations which gives up-to-the-

minute information on news, weather, television programmes, share prices and

many other topics.

Switch on/off 

Press the TEXT button to switch to teletext. The initial page or last selected page

appears on the screen. Two page numbers, TV station name, date and time are

displayed on the screen head line. The first page number indicates your selection,

while the second shows the current page displayed. Press the TEXT or TV/AV

button to switch off teletext. The previous mode reappears.

SIMPLE text (standard teletext)

Press the NUMBER, 

¡ª/¡

button to select a teletext page.

TOP text (option)

The user guide displays four fields-red, green, yellow and blue at the bottom of the

screen. The yellow field denotes the next group and the blue field indicates the

next block. Press the NUMBER, 

¡ª/¡

or coloured buttons to select a teletext page. 

FASTEXT 

The teletext pages are colour coded along the bottom of the screen and are

selected by pressing the corresponding coloured button. Press the INDEX button

to select the index page. Press the NUMBER or 

¡ª/¡

button to select a teletext

page.

Programming a colour button in LIST mode

If the TV is in SIMPLE text,TOP text or FASTEXT, press the MODE button to

switch to LIST mode. Press the NUMBER, 

¡ª/¡

or four coloured buttons to select a

teletext page.

1.

Using the NUMBER buttons, select the page you wish to programme.

2.

Wait until the page is displayed on the screen and press the OK button.  The

page numbers in the colour boxes along the bottom of the screen change to

“000?”.

3.

Press a colour button to store the page number. From now on, you can select

this page with the same coloured button.

4.

The three other coloured buttons are programmed in the way.

Special teletext functions

REVEAL

Press this button to display concealed information, such as solutions of riddles or

puzzles. Press this button again to remove the information from the display.

SIZE

Selects double height text. Press this button to enlarge the top half of the page.

Press this button again to enlarge the bottom half of the page. Press this button

again to return to the normal display.

UPDATE

Displays the TV picture on the screen while waiting for the new teletext page. The

display      will appear at the top left hand corner of the screen. When the updated

page is available then display

will change to the page number. Press this button

to view the updated teletext page.

HOLD

Stops the automatic page change which will occur if a teletext page consists of 2 or

more sub pages. The number of sub pages and the sub page displayed is, usually,

shown on the screen below the time. When this button is pressed the stop symbol

is displayed at the top left hand corner of the screen and the automatic page

change is inhibited. To continue press this button again.

MIX

Displays the teletext pages superimposed on the TV picture. To switch the TV

picture off press this button again.

TIME
When viewing a TV programme, press this button to display the time at the top
right hand corner of the screen. Press this button again to remove the display. In
the teletext mode, press this button to select a sub page number. The sub page
number is displayed at the bottom of the screen. To hold or change the sub page,
press the 

¡ª/¡

or NUMBER buttons. Press again to exit this function.

Teletext (option)

 


background image

Troubleshooting check list

The mains plug-(plugged in and

switched on)
Is the TV switched on

Try another channel (weak signal)

Check aerial (plugged into TV?)

Check aerial (broken lead?)

Check aerial

Check for local interference

Adjust contrast

Adjust brightness

Adjust colour

Adjust volume

Check the batteries in remote control

Check Audio/Video sockets (VCR

only)

Symptoms

No picture, no sound

Sound OK, poor picture

Picture OK, poor sound

Picture blurred

Lines or streaks in picture

Poor reception on some channels

No colour

Poor colour

Remote control does not work

Check these items and try
to adjust these