PDF User Manual

  1. Home
  2. Manuals
  3. LG 563LE Owner's Manual

LG 563LE Owner's Manual

FLATRON LCD 563LS FLATRON LCD 563LE

Made by: LG
Type: Owner's Manual
Category: Monitor
Pages: 10
Size: 0.53 MB

 

Download PDF User Manual



Full Text Searchable PDF User Manual



background image

A1

Introduction

The 563LE Flat Panel Monitor has an active matrix TFT (Thin-Film
Transistor) LCD (Liquid Crystal Display).
This monitor is designed for use in small working areas or for those who need
more working space on the desk.

Features

The

563LE

is a 15.0-inch (15.0 inches viewable) intelligent micropro-cessor

based monitor. 

Digitally controlled auto-scanning is done with the microprocessor for horizontal
scan frequencies between 31 and 61kHz, and vertical scan frequencies
between 56 and 75Hz. 

The microprocessor-based digital controls allow you to adjust conveniently a
variety of image controls by using the OSD (On Screen Display).

The monitor is shipped with 14 factory pre-programmed video modes that are
permanently resident. In addition, there are 16 user-storable modes, for a total
of 30 memory modes.

Plug and play capability if supported by your system.

This monitor has DDC 2B function.

*

Compliant with the following regulated specifications :

*

- EPA E

NERGY

S

TAR

- Swedish TCO’99

ENGLISH

*

For detailed information, please refer to the 

Reference Guide

provided .

 


background image

Connecting the Monitor

A2

On the back of the monitor are two plug-in connections; one for the AC
power cord, and the other for the signal cable from the video card.

Power off both the monitor and PC.

Connect the 15 pin VGA connector of the supplied signal cable to the output
VGA video connector on the PC and the matching input connector on the rear
of the monitor. The connectors will mate only one way. If you cannot attach
the cable easily, turn the connector upside down and try again. When mated,
tighten the thumbscrews to secure the connection.  

Locate the appropriate MAC to VGA adapter block at your local computer
store. This adapter changes the high density 3 row 15 pin VGA connector to
the correct 15 pin 2 row connection to mate with your MAC. Attach the other
end of the signal cable to the side of the adapter block with 3 rows.

Connect the attached adapter block/signal cable to the video output on your
MAC.

Connect the plug from the AC-DC adapter into the connector on the display
unit.

Connect one end of the AC power cord into the AC-DC adapter.

Plug the other end into a properly grounded three-prong AC outlet. 

Power on the PC, then the monitor.

If you see the 

NO SIGNAL

message, check the signal cable and

connectors. 

After using the system, power off the monitor, then the PC.

3

2

1

Power Cord

Signal Cable 

D-15P

IBM PC

MACINTOSH

D-15P

Mac Adapter

*

NOTE :

If you see the “OUT OF

RANGE” message, check to make
sure your system is set to one of the
factory preset modes.(see page A8)

1

2

3

3

2

1

4

5

6

2'

2

2'

AC-DC adapter

 


background image

A3

Location and Function of Controls

Rear View

Front View

VESA wall mounting

Connected to another object
(stand type and wall-mounted
type - 

optional

)

Kensington Security Slot

Connected to a locking
cable that can be
purchased separately at
most computer stores

NOTE : 

This monitor accept a 75mm x 75mm VESA-compliant mounting interface pad.

D-Sub Signal Connecter

ID Label

DC Power Connecter

-

+

Power Indicator

Power  Button

AUTO/SET Button

Buttons

OSD Button

OSD

AUTO

/SET

• •

• •

 


background image

Control Panel Function

A4

Front Panel Controls

OSD

        AUTO/SET

Use this button to enter and from the on
screen display (OSD).

Use these buttons to choose or adjust items in
the on screen display.

<Shortcut Keys>

• Brightness and Contrast can be adjusted directly without

entering the On Screen Display (OSD) system. Touch
the         

buttons to adjust the settings and then

the 

OSD button

to save all changes. The Brightness

and Contrast functions are also available in the On
Screen Display (OSD) menu.

OSD

AUTO/SET

OSD Button

Buttons

This indicator lights up green when the
monitor operates normally. If the monitor is in
DPM (Energy Saving) mode (stand-by/
suspend/power off), this indicator color
changes to amber.

Power (DPMS)
Indicator

Use this button to turn the monitor on or off.

Power Button

Use this button to enter a selection in the on
screen display.

* AUTO adjustment function

Touch the 

AUTO

/

SET

button before using OSD menu.

This button is for the automatic adjustment of the screen
position, clock and phase. 

Note

: Some signal from some graphics boards may not function

properly. I

f the results are unsatisfactory

, adjust your monitor’s

Position, Clock and Phase manually.

AUTO/SET Button

Control

Function

OSD Button

AUTO/SET Button

Power Button

Power (DPMS) Indicator

Buttons

P R O C E S S I N G

A U T O   C O N F I G U R A T I O N

100

100

 


background image

Making adjustments to the image size, position and operating parameters of
the monitor are quick and easy with the On Screen Display Control system. A
quick example is given below to familiarize you with the use of the controls.
Following section is an outline of the available adjustments and selections you
can make using the OSD.

To make adjustments in the On Screen Display, follow these steps:

Press the 

OSD Button

, then the main menu of the OSD appears.

To access a control, use the         

Buttons

. When the icon you want

becomes highlighted, press the  

AUTO/SET Button

.

Use the               

Buttons

to adjust the item to the desired level.

Accept the changes by pressing the 

AUTO/SET Button

.

Exit the OSD by Pressing the

OSD Button

.

A5

On Screen Display (OSD) Control Adjustment

NOTE

Allow the monitor to stabilize for at least 30 minutes before making image adjustment.

OSD

OSD

AUTO

/

SET

AUTO

/

SET

1

1
2
3
4
5

6
7

1

2

2
3
4
5

6
7

1
2

3

3
4
5

6
7

1
2
3

4

4
5

6
7

1
2
3
4

5

5

6
7

 


background image

A6

On Screen Display(OSD) Selection and Adjustment 

You were introduced to the procedure of selection and adjusting an item
using the OSD system.  Listed below are the icons, icon names, and icon
descriptions of the items that are shown on the Menu.

OSD Adjust

Description

88

100

BRIGHTNESS CONTRAST

9300K                6500K

COLOR

PRESET    

RED
GREEN
BLUE

61

39

POSITION

Brightness

Used to adjust the brightness of the
screen. 

Contrast 

Adjust the display to the contrast
desired. 

PRESET

RED

GREEN

BLUE

9300K/ 6500K

To appear the displays color
temperature.

• 

9300K:Slightly bluish white.

• 

6500K:Slightly reddish white.

To set your own color levels.

To set your own color levels.

To set your own color levels.

Vertical Position

To move image up and down.

Horizontal Position

To move picture image left and right.

 


background image

A7

On Screen Display(OSD) Selection and Adjustment 

OSD Adjust

Description

TRACKING

CLOCK

PHASE

LANGUAGE

ENGLISH

OSD POSITION

ELAPSED TIME

1 0 2 4 x 7 6 8 / 6 0 H z

P R E S E T   M O D E

SETUP

H

0

To minimize any vertical bars or
stripes visible on the screen
background.The horizontal screen
size will also change.

To adjust the focus of the display.
This item allows you to remove any
horizontal noise and clear or sharpen
the image of characters.

To choose the language in which the
control names are displayed.

To adjust position of the OSD window
on the screen.

To display the use time of monitor

LANGUAGE

OSD POSITION

ELAPSED TIME

CLOCK

PHASE

 


background image

A8

Video Memory Modes

The monitor has 30 memory locations for display modes, 14 of which are
factory preset to popular video modes.

Display Modes (Resolution)

User Modes

Modes 15-30 are empty and can accept new video data. If the monitor detects a
new video mode that has not been present before or is not one of the preset
modes, it stores the new mode automatically in one of the empty modes starting
with mode 15.

If you use up the 16 blank modes and still have more new video modes, the
monitor replaces the information in the user modes starting with mode 15.

1
2
3
4
5
6
7
8
9

10
11
12
13
14

640 x 350
720 x 400
640 x 480
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
832 x 624

1024 x 768
1024 x 768
1024 x 768

31.47
31.47
31.47
35.00
37.86
37.50
35.16
37.88
48.08
46.88
49.72
48.36
56.48
60.02

70
70
60
67
73
75
56
60
72
75
75
60
70
75

Display Modes (Resolution)

Horizontal Freq.(kHz)

Vertical Freq.(Hz)

VGA
VGA
VGA
MAC
VESA
VESA
VESA
VESA
VESA
VESA
MAC
VESA
VESA
VESA

 


background image

A9

Troubleshooting

Check the following before calling for service.

Display Position is incorrect.

Push the  

AUTO/SET 

Button.

If the results are unsatisfactory, adjust the image position using the H position
and V position icon in the on screen display.

On the screen background, vertical bars or stripes are visible.

Push the 

AUTO/SET

Button.

If the results are unsatisfactory, decrease the vertical bars or stripes using the

CLOCK

icon in the on screen display.

Any horizontal noise appearing in any image or characters are
not clearly portraid.

Push the 

AUTO/SET

Button.

If the results are unsatisfactory, decrease the horizontal bars using the 

PHASE

icon in the on screen display.

NO SIGNAL message.

The signal cable is not connected, or is loose. Check and secure the
connection.

OUT OF RANGE message appears.
Picture is blank.

The frequency of the signal from the video card is outside the operating range
of the monitor.

Horizontal Frequency: 31kHz-61kHz
Vertical Frequency: 56Hz-75Hz

*

Use the graphics board's utility software to change the frequency setting (Refer to the
manual for graphics board).

* You can change the setup to the supported resolution using the 

Safe Mode

(Press the

F8 key during booting the system).

The power LED is illuminated amber.

The monitor is in its display power management mode.
There is no active signal coming from the PC.
The signal cable is not fastened securely.
Check the computer power and graphics adapter configuration.

The monitor doesn't enter the power saving off mode (Amber).

Computer video signal is not VESA DPMS standard. Either the PC or the video
controller card is not using the VESA DPMS power management function.

 


background image

A10

Specifications

Type

15.0inch (38.1cm) Flat Panel Active matrix-TFT LCD,
Anti-Glare coating

Viewable Size

15.0inch (38.1cm) 

Pixel pitch

0.3 x 0.3mm

Horizontal Freq.

31 - 61kHz (Automatic)

Vertical Freq.

56 - 75Hz (Automatic)

Input Form

Separate TTL, Positive/Negative

Signal Input

15 pin D-Sub Connector

Display Area

304 x 228mm / 12.0 x 9.0inch

Input Form

Separate, RGB Analog, 0.714Vp-p/75ohm, Positive

Max

VESA 1024 x 768@75Hz 

Recommend

VESA 1024 x 768@60Hz

Normal

33W

Stand-by/Suspend

3W 

Power Off

3W 

Width

38.92 cm / 15.95 inches

Height

36.25 cm / 14.24 inches

Depth

18.24 cm / 7.18 inches

DC 12V  3A

Input

AC 100-240V 50-60Hz 1.2A~0.6A

Output

DC 12V 3A

Net

4.8 kg (10.58 lbs)

Down

Up

30˚

Operating Condition

Temperature

10 ˚C to 35 ˚C

Humidity

10 % to 80 % non-Condensing

Storage Condition

Temperature

-20 ˚C to 60 ˚C

Humidity

5 % to 95 % non-Condensing

NOTE

Information in this document is subject to change without notice.

Display

Sync Input

Video Input

Resolution

Power
Consumption

Dimensions 

Power Input

AC-DC Adapter

Weight

Tilt Range

Environmental
Conditions

-

+