PDF User Manual

  1. Home
  2. Manuals
  3. LG 37LC2D Owner's Manual

LG 37LC2D Owner's Manual

42LC2D\ 42PC3DV\ 42PC3D\ 42PC3D-UD\ 50PC3D-UD\ 50PC3D\ 32LC2D\ 42PC3DV-UD

Made by: LG
Type: Owner's Manual
Category: LCD TV
Pages: 17
Size: 1.75 MB

 

Download PDF User Manual



Full Text Searchable PDF User Manual



background image

   

 

EUT Type: 37” LCD TV/ Monitor 

FCC ID: BEJ37LDD

 

Test Report No.: GETEC-E3-05-081 

FCC Class B Certification 

 

 

APPENDIX H 

: USER’S MANUAL   

 

 


background image

Please read this manual carefully before operating your set. 
Retain it for future reference.
Record model number and serial number of the set. 
See the label attached on the back cover and quote 
this  information to your dealer 
when you require service.

P/NO : 3828TUL527A (0511-REV00)

Printed in Korea

OWNER’S MANUAL

LCD TV

MODELS: 32LC2D

37LC2D
42LC2D

PLASMA TV

MODELS: 42PC3D

42PC3D-UD

42PC3DV

42PC3DV-UD

50PC3D

50PC3D-UD

Internet Home Page : http://www.lge.com

http://www.lg.ca

 


background image

Warning

WARNING

:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to

the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of suffi-
cient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of

important operating and maintenance (servicing) instructions in the literature accompanying the appli-
ance.

NOTE TO CABLE/TV INSTALLER:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric
Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the building, as close to the point of the cable entry as prac-
tical.

REGULATORY INFORMATION

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment. 

CAUTION:

Do not attempt to modify this product in any way without written authorization from LG Electronics Corporation.
Unauthorized modification could void the user’s authority to operate this product.

U.S.A. only -----------------------------------------------

COMPLIANCE:

The responsible party for this product’s compliance is:
LG Electronics U.S.A., Inc.
1000 Sylvan Avenue, Englewood Cliffs, NJ  07632
Phone: 1-201-816-2000
http://www.lgusa.com

---------------------------------------------------------------

CAUTION

RISK OF ELECTRIC SHOCK
        DO NOT OPEN

W

W

arning

arning

 


background image

Safety Instructions

WARNING :

To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This Apparatus To Rain Or Moisture.

Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the
apparatus.

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings. 

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any of the ventilation openings. Install in

accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has
two blades and a third grounding prong. The wide blade
or the third prong is provided for your safety. When the
provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or

pinched particularly at plugs, convenience recepta-
cles, and the point where they exit from the apparatus.

11. Only use the attachments / accessories specified by

the manufacturer.

Safety Instructions

Safety Instructions

Ow

ner's

 M

an

ual

 


background image

Safety Instructions

12. Use only with a cart, stand, tripod, bracket, or table

specified by the manufacturer, or sold with the appa-
ratus. When a cart is used, use caution when moving
the cart / apparatus combination to avoid injury from
tip-over.

13. Unplug this apparatus during lightning storms or when

unused for long periods of time.

14. Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been
damaged in any way, such as power supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normal-
ly, or has been dropped.

On Disposal 

a. The fluorescent lamp used in this product contains a small amount of mercury.
b. Do not dispose of this product with general household waste.

Disposal of this product must be carried out in accordance to the regulations of your local authority.

Note

- If the TV feels cold to the touch, there may be a small “flicker” when when it is turned on. This is normal, there is noth-

ing wrong with TV.

- Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have

no adverse effect on the monitor's performance.

- Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some

temporary distortion effects on the screen.

CAUTION concerning the Power Cord

Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that
appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain.

Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords,
or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire.
Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discon-
tinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer.

Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or
walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.

 


background image

Introduction

Controls

Controls

(Model Name: 32/37/42LC2D) 

(Model Name: 32/37/42LC2D) 

- This is a simplified representation of front panel. 
- Here shown may be somewhat different from your TV.

R

CH

VOL

VOL

ENTER

ENTER

MENU

MENU

INPUT

INPUT

ON/OFF

ON/OFF

CHANNEL Buttons

VOLUME Buttons

ENTER Button

MENU Button

INPUT Button

ON/OFF Button

Remote Control Sensor

Power/Standby Indicator

• illuminates red in standby mode.

• illuminates green when the set is

switched on.

 


background image

Introduction

Connection Options (Model Name: 32/37/42LC2D)

Connection Options (Model Name: 32/37/42LC2D)

AC IN

AV IN 2

AV IN 2

L/

L/MONO

MONO

R

AUDIO

AUDIO

S-VIDEO

S-VIDEO

VIDEO

VIDEO

HDMI/DVI IN

HDMI/DVI IN

DIGITAL AUDIO OUT

DIGITAL AUDIO OUT

OPTICAL

OPTICAL

RS-232C IN

RS-232C IN

(CONTROL

(CONTROL&SERVICE)

SERVICE)

REMOTE

CONTROL

RGB IN

RGB IN

(PC

(PC

/

DTV)

DTV)

AUDIO IN

AUDIO IN

(RGB/DVI)

(RGB/DVI)

VIDEO

VIDEO

AUDIO

AUDIO

MONO

(

)

VIDEO

VIDEO

AUDIO

COMPONENT IN

COMPONENT IN

S-VIDEO

S-VIDEO

AV IN 1

AV IN 1

AV OUT

AV OUT

ANTENNA

ANTENNA

IN

CABLE

CABLE

IN

AC IN

AUDIO Input

S-VIDEO Input

VIDEO Input

DIGITAL AUDIO OUT

OPTICAL

AV OUT

AV IN1

COMPONENT IN 1/2

HDMI / DVI IN

ANTENNA IN

CABLE IN

AUDIO IN 
(RGB/DVI)

RGB IN 
(PC/DTV)

AC IN

RS-232C INPUT
(CONTROL&SERVICE)

REMOTE CONTROL Port

- Here shown may be somewhat different from your TV.

 


background image

Installation

Installation

Installation

Desktop Pedestal Installation

4 inches

4 inches

4 inches

4 inches

4 inches

4 inches

4 inches

4 inches

For proper ventilation, allow a clearance of 4" on each side and from the wall.

GROUNDING

Ensure that you connect the earth ground wire to prevent pos-
sible electric shock. If grounding methods are not possible,
have a qualified electrician install a separate circuit breaker.
Do not try to ground the unit by connecting it to telephone
wires, lightening rods, or gas pipes.

Power

Supply

Short-circuit

Breaker

• The TV can be installed in various ways such as on a wall, or on a desktop etc.
• The TV is designed to be mounted horizontally.

 


background image

Installation

How to join the product assembly to the wall to protect the set tumbling

- Set it up close to the wall so the product doesn’t fall over when it is pushed backwards. 
- The instructions shown below is a safer way to set up the product, which is to fix it on the wall so the prod-

uct doesn’t fall over when it is pulled in the forward direction. It will prevent the product from falling for-
ward and hurting people. It will also prevent the product from damage caused by fall. Please make sure
that children don’t climb on or hang from the product. 

42PC3D/42PC3DV/50PC3D

Notes

• When moving the product to another place undo the ropes first.
• Use a product holder or a cabinet that is big and strong enough for the size and weight of the product. 
• To use the product safely make sure that the height of the bracket that is mounted on the wall is same

as that of the product. 

2

1

3

Use the bracket and the bolt to fix the product to the wall as shown in the picture. 

Secure the bracket with the bolt (not provided as parts of the product, must purchase separately) on
the wall.

Use a sturdy rope (not provided as parts of the product, must purchase separately) to tie the product.
It is safer to tie the rope so it becomes horizontal between the wall and the product.

1

2

3

32/37/42LC2D

If the set will be mounted on a desk top, insert the 2 eye-bolts and tighten them securely in the upper
holes as shown.

Install the wall brackets on the wall with 2 bolts*, (not supplied with the product), as shown.

Match the height of the eye-bolts and the wall brackets.

Check to be sure the eye-bolts and the brackets are tightened securely.

Secure the TV assembly to the wall with strong strings or wire cables, (not supplied with the product), as
shown.

1

2
3
4
5

 


background image

Installation

Digital Audio Output

1

2

3

Connect one end of an optical cable to the TV
Digital Audio Optical Output port.

Connect the other end of the optical cable to the
digital audio optical input on the audio equipment.

See the external audio equipment instruction
manual for operation. 
When connecting with external audio equip-
ments, such as amplifiers or speakers, please
turn the TV speakers off. 

HDMI/DVI IN

DIGITAL AUDIO OUT

OPTICAL

RS-232C IN

RS-232C IN

(CONTROL&SERVICE)

- Send the TV’s audio to external audio equipment (stereo system) via the Digital Audio Output Optical port.

CAUTION

Do not look into the optical output port. Looking at the laser beam may damage your vision.

1/2

Monitor Out Setup

1

2

Connect the second TV or monitor to the TV’s

AV

OUTPUT

jacks.

See the Operating Manual of the second TV or
monitor for further details regarding that device’s
input settings.

S-VIDEO IN

(R) AUDIO (L) VIDEO

VIDEO

VIDEO

AUDIO

MONO

(

)

VIDEO

VIDEO

AUDIO

UDIO

COMPONENT IN

S-VIDEO

AV IN 1

AV OUT

- The TV has a special signal output capability which allows you to hook up a second TV or monitor.

1/2

• Component 1-2, RGB-PC/RGB-DTV,

HDMI/DVI, DTV input sources cannot be used
for Monitor out.

• When connecting with external audio equip-

ments, such as amplifiers or speakers, please
turn the TV speakers off.

(Refer to p.43)

• We recommend to use the video and audio

output jacks for VCR recording.

 


background image

Installation

- This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings. 

PC Setup

When connecting with a D-sub 15 pin cable

1

2

3

4

Connect the RGB output of the PC to the 

RGB IN

(PC/DTV)

(32/37/42LC2D Model) 

/ RGB

(PC/DTV)

(42PC3D/3DV/50PC3D Model) jack on

the set.

Connect the PC audio outputs to the 

AUDIO IN

(RGB/DVI)

(32/37/42LC2D Model)

/AUDIO

(RGB/DVI)

(42PC3D/3DV/50PC3D Model) jack on

the set.

Turn on the PC and the set. 

Select

RGB-PC

input source with using the

TV/VIDEO

button on the remote control.

(R) AUDIO (L)

RGB-PC OUTPUT

REMOTE

CONTROL

RGB IN

(PC

/

DTV)

AUDIO IN

AUDIO IN

(RGB/DVI)

1

2

PC

When connecting with a HDMI to DVI cable

1

2

3

4

Connect the DVI output of the PC to the 

HDMI/DVI IN 

jack on the set.

Connect the audio outputs of the PC to the 

AUDIO IN (RGB/DVI) 

(32/37/42LC2D Model)

/AUDIO (RGB/DVI) 

(42PC3D/3DV/50PC3D Model) jack on the set.

Turn on the PC and the set. 

Select

HDMI/DVI

input source with using the 

TV/VIDEO

button on the remote control.

(R) AUDIO (L)

DVI-PC OUTPUT

HDMI/DVI IN

DIGITAL AUDIO OUT

OPTICAL

RS-232C IN

RS-232C IN

(CONTROL&SERVICE)

REMOTE

CONTROL

RGB IN

(PC

/

DTV)

AUDIO IN

AUDIO IN

(RGB/DVI)

ANTENNA

IN

CABLE

IN

PC

• If the PC has a DVI output and no HDMI output, a separated audio connection is necessary.
• If the PC does not support Auto DVI, you need to set the output resolution appropriately. To get the

best picture quality, adjust the output resolution of PC graphics card's output resolution to
1024x768, 60Hz.

1

2

 


background image

30

Installation

1. To get the best picture quality, adjust the PC

graphics card to 1024x768, 60Hz.

2. Depending on the graphics card, DOS mode may

not work if a HDMI to DVI Cable is in use.

3. When Source Devices connected with HDMI1/DVI

Input, output PC Resolution (VGA, SVGA, XGA),
Position and Size may not fit to Screen.Press the
ADJUST button to adjust the screen Position of TV
SET and contact an PC graphics card service cen-
ter.

4. When Source Devices connected with HDMI/DVI

Input, output TV SET Resolution (480p, 720p,
1080i) and TV SET Display fit EIA/CEA-861-B
Specification to Screen. If not, refer to the Manual
of HDMI/DVI Source Devices or contact your ser-
vice center.

5. In case HDMI/DVI Source Devices is not connect-

ed Cable or poor cable connection,  "NO SIGNAL"
OSD display in HDMI1/DVI Input. In case that
Video Resolution is not supported TV SET output
in HDMI/DVI Source Devices, "INVALID FORMAT"

OSD display. Refer to the Manual of HDMI1/DVI
Source Devices or contact your service center.

6. Check the image on your TV. There may be noise

associated with the resolution, vertical pattern,
contrast or brightness in PC, HDMI/DVI mode. If
noise is present, change the PC or HDMI/DVI
mode to another resolution, change the refresh
rate to another rate or adjust the brightness and
contrast on the menu until the picture is clear. If the
refresh rate of the PC graphic card can not be
changed, change the PC graphic card or consult
the manufacturer of the PC graphic card.

7. Avoid keeping a fixed image on the TV's screen for

a long period of time. The fixed image may become
permanently imprinted on the screen.

8. The synchronization input form for Horizontal and

Vertical frequencies is separate.

Supported Display Resolution 

(RGB-PC, HDMI/DVI Mode)

Resolution

*

640x350

*

720x400

640x480

Horizontal

Frequency (kHz)

31.468

31.469

31.469

37.861

37.500

70.09

70.08

59.94

72.80

75.00

Vertical

Frequency (Hz)

Resolution

* RGB-PC only

800x600

1024x768

Horizontal

Frequency (kHz)

35.156

37.879

48.077

46.875

48.363

56.476

60.023

56.25

60.31

72.18

75.00

60.00

70.06

75.02

Vertical

Frequency (Hz)

 


background image

Installation

* Adjustment for screen Position, Size, and Phase

* Initializing (Reset to original factory values)

- To initialize the adjusted values

Close

POSITION

G

SIZE

PHASE

RESET

Adjust

D

F

G

E

Close

POSITION

SIZE

PHASE

RESET    

G

Adjust

Initialize Settings

Position This function is to adjust

picture to left/right and
up/down as you prefer. 

Size

This function is to mini-
mize any vertical bars or
stripes visible on the
screen background. And
the horizontal screen size
will also change. 

Phase

This function allows you to
remove

any horizontal

noise and clear or sharpen
the image of characters.

Mini Glossary

- When RGB connect to PC input and select the RGB-PC, this function is used. 
- When HDMI/DVI connect to PC input and select HDMI/DVI input, this function is used. 
- In RGB-DTV mode, SIZE and PHASE is not available.
- After connecting RGB-PC or HDMI/DVI to PC input and checking the screen quality.

Press the 

ADJUST

button and then use 

/

E

button to select 

POSITION

,

SIZE

, or 

PHASE

.

Press

ENTER

button and then use 

/

E

/

/

buttons to make

appropriate adjustments.

• The 

PHASE

adjustment range is -16 ~ +16.

(In HDMI/DVI-PC mode, 

PHASE

is not available.)

• The 

SIZE

adjustment range is -50 ~ +50.

Press

ENTER

button.

1

2

3

Press the 

ADJUST

button and then use 

/

E

button to select the

RESET 

option.

Press

ENTER

button and then use 

/

button to select 

Yes

.

Press

ENTER

button.

1

2

3

Screen Setup for PC mode

 


background image

Reference

No. Pin 

Name

1 No 

connection

2

RXD (Receive data)

3

TXD (Transmit data)

4

DTR (DTE side ready)

5

GND

6

DSR (DCE side ready)

7

RTS (Ready to send)

8

CTS (Clear to send)

9

No Connection

1

5

6

9

2
3
5
4
6
7
8

RXD

TXD

GND

DTR
DSR
RTS
CTS

TXD

RXD

GND

DSR
DTR

CTS
RTS

PC

7-Wire Configurations

(Serial female-female NULL modem cable)

D-Sub 9

3
2
5
6
4
8
7

TV

D-Sub 9

2
3
5
4
6
7
8

RXD

TXD

GND

DTR
DSR
RTS
CTS

TXD

RXD

GND

DTR
DSR
RTS
CTS

PC

3-Wire Configurations

(Not standard)

D-Sub 9

3
2
5
4
6
7
8

TV

D-Sub 9

- Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system) and

control the Monitor’s functions externally.

- Connect the serial port of the control device to the RS-232C jack on the TV back panel.
- RS-232C connection cables are not supplied with the TV.

T

T

ype of Connector; D-Sub 9-Pin Male

ype of Connector; D-Sub 9-Pin Male

RS-232C Configurations

RS-232C Configurations

External Control Device Setup

External Control Device Setup

RS-232C Setup

RS-232C Setup

HDMI/DVI IN

DIGITAL AUDIO OUT

OPTICAL

RS-232C IN

(CONTROL&SERVICE)

PC

 


background image

Reference

Set ID

Set ID

- Use this function to specify a TV ID number. 
- Refer to ‘Real Data Mapping’. See page

56

.

• Baud rate : 9600 bps (UART)
• Data length : 8 bits
• Parity : None
• Stop bit : 1 bit
• Communication code : ASCII code

* Use a crossed (reverse) cable.

Communication Parameters

Communication Parameters

1. Press the 

MENU

button and then use 

/

E

button to select the

SETUP

menu.

2. Press the 

G

button and then use

/

E

button to select 

Set ID

.

3. Press the 

G

button and then use 

/

E

button to adjust 

Set ID

to

choose the desired TV ID number. The adjustment range of 

Set ID

is 1 ~ 99.

4. Press 

EXIT

button to return to TV viewing or press 

MENU

button to

return to the previous menu.

Previous

MENU

EZ Scan

Manual Scan

Channel Edit

DTV Signal

Input Source

Input Label

Set ID

G

1

SETUP

G

VIDEO

AUDIO

TIME

OPTION

LOCK

Transmission

* [Command 1]: First command to control the set.(j,k,m or x)
* [Command 2]: Second command to control the set.
* [Set ID]: You can adjust the set ID to choose desired monitor

ID number in Setup menu. Adjustment range is 1
~ 99. When selecting Set ID ‘0’, every connected
the TV is controlled. Set ID is indicated as decimal
(1~99) on menu and as Hexa decimal (0x0~0x63)
on transmission/receiving protocol.

* [DATA]: To transmit command data.

Transmit ‘FF’ data to read status of command.

* [Cr]: Carriage Return

ASCII code ‘0x0D’

* [   ]: ASCII code ‘space (0x20)’

[Command1][Command2][  ][Set ID][  ][Data][Cr]

T

T

ransmission / Receiving  Protocol

ransmission / Receiving  Protocol

OK Acknowledgement

* The Monitor transmits ACK (acknowledgement) based on

this format when receiving normal data. At this time, if the
data is data read mode, it indicates present status data. If
the data is data write mode, it returns the data of the PC
computer.

[Command2][  ][Set ID][  ][OK][Data][x]

Error Acknowledgement

* The Monitor transmits ACK (acknowledgement) based on

this format when receiving abnormal data from non-viable
functions or communication errors.

[Command2][  ][Set ID][  ][NG][Data][x]

Data 1: Illegal Code

2: Not supported function
3: Wait more time

22. Channel Tuning

m

a       

physical/program high

major/program low

major low      minor high       minor low        attribute

23. Channel Add/Del

m

b                  00 ~ 01

24. Key

m

c                  

key code

25. Input Select              x            b                 

*

(Refer to p.

59

)

COM-
MAND 2

COM-
MAND 1

DATA 0

(Hexadecimal)

DATA 1

(Hexadecimal)

DATA 2

(Hexadecimal)

DATA 3

(Hexadecimal)

DATA 4

(Hexadecimal)

DATA 5

(Hexadecimal)

01. Power  

a

0 ~ 1

02. Input Select 

b

0 ~ 8

03. Aspect Ratio 

c       

*

(Refer to p.

56

)

04. Screen Mute 

d

0 ~ 1

05. Volume Mute 

e

0 ~ 1

06. Volume Control 

f

0 ~ 64

07. Contrast 

g

0 ~ 64

08. Brightness 

h

0 ~ 64

09. Color 

i

0 ~ 64

10. Tint 

j

0 ~ 64

11. Sharpness 

k

0 ~ 64

12. OSD Select 

l

0 ~ 1

13. Remote Control Lock Mode  k 

m

0 ~ 1

14. Treble 

r

0 ~ 64

15. Bass  

s

0 ~ 64

16. Balance  

t

0 ~ 64

17. Color Temperature  

u

0 ~ 2

18. ISM Method

j

p       

*

(Refer to p.

58

)

19. Low Power

j

q

0 ~ 1

20. Orbiter Time Setting

j

r

1 ~ FE

21. Orbiter Pixel Setting

j

s

1 ~3

COMMAND 1 COMMAND 2

DATA

(Hexadecimal)

Command Reference List

Command Reference List

* Command 

18~21

: 42PC3D/3DV, 50PC3D models only

 


background image

Reference

1. Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water

and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe
the screen.

2. Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV.

To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.
Please be sure not to use a wet cloth.

If you expect to leave your TV dormant for a long time (such as a vacation), it’s a good idea to
unplug the power cord to protect against possible damage from lightning or power surges.

- Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have

your new TV. Be sure to turn the power off and unplug the power cord before you begin any cleaning.

Cleaning the Screen

Cleaning the Screen

Cleaning the Cabinet

Cleaning the Cabinet

Extended

Extended

Absence

Absence

Maintenance

Maintenance

Product Specifications

Product Specifications

• The specifications shown above may be changed without prior notice for quality improvement.

MODEL

Power requirement

Television System

Program Coverage

External Antenna Impedance

Operating Temperature Range

Operating Humidity Range

32LC2D

37LC2D

42LC2D

NTSC-M, ATSC, 64 & 256 QAM

VHF 2 ~ 13, UHF 14 ~ 69, CATV 1 ~ 135, CADTV 1 ~ 135, DTV 2 ~ 69

75

32 ~ 104°F (0 ~ 40°C)

Less than 80%

AC100-240V ~ 50/60Hz 1.5A AC100-240V ~ 50/60Hz 2.0A AC100-240V ~ 50/60Hz 2.5A

MODEL

Power requirement

Television System

Program Coverage

External Antenna Impedance

Operating Temperature Range

Operating Humidity Range

Resolution

42PC3D/3DV-UD

50PC3D-UD

AC100-240V ~ 50/60Hz 2.0A

NTSC-M, ATSC, 64 & 256 QAM

VHF 2 ~ 13, UHF 14 ~ 69, CATV 1 ~ 135, CADTV 1 ~ 135, DTV 2 ~ 69

75

32 ~ 104°F (0 ~ 40°C)

Less than 80%

852 x 480 (Dot)

1366 x 768 (Dot)

 


background image