LG 32LT560H Owner's Manual

Download PDF User Manual

Full Text Searchable PDF User Manual

www.lg.com

OWNER’S MANUAL

LED LCD TV

PUBLIC DISPLAY MODE SETUP

Please read this manual carefully before operating your set and retain it

for future reference.

32LT560H

37LT560H

42LT560H

26LT360C

32LT360C

42LT360C

32CS460C

42CS460C

ENG

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

Always comply with the following precautions to avoid dangerous situations and ensure peak performance
of your product.

TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR
BACK). NO USER SERVICEABLE PARTS
INSIDE. REFER TO QUALIFIED SERVICE
PERSONNEL.

The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert the user to the
presence of uninsulated “dangerous

voltage” within the product’s enclosure that
may be of sufficient magnitude to constitute a
risk of electric shock to persons.

The exclamation point within an
equilateral triangle is intended to alert
the user to the presence of important

operating and maintenance (servicing)
instructions in the literature accompanying
the appliance.

- TO REDUCE THE RISK OF FIRE AND

ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE.

WARNING/CAUTION

Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

Short-circuit

Breaker

Power Supply

Do not install near any heat sources such as

radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

Short-circuit

Breaker

Power Supply

Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type

plug has two blades and a third grounding prong.

The wide blade or the third prong are provided for

your safety. If the provided plug does not fit into your

outlet, consult an electrician for replacement of the

obsolete outlet (Can differ by country).

Short-circuit

Breaker

Power Supply

Protect the power cord from being walked on

or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the

apparatus.

Short-circuit

Breaker

Power Supply

Only use attachments/accessories specified by the

manufacturer.

Short-circuit

Breaker

Power Supply

Use only with a cart, stand, tripod, bracket, or table

specified by the manufacturer, or sold with the

apparatus. When a cart is used, use caution when

moving the cart/apparatus combination to avoid injury

from tip-over.

Short-circuit

Breaker

Power Supply

Unplug this apparatus during lightning storms or

when unused for long periods of time.

Short-circuit

Breaker

Power Supply

Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.

Do not use this apparatus near water.

Short-circuit

Breaker

Power Supply

Clean only with a dry cloth.

Short-circuit

Breaker

Power Supply

ENG

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has

been exposed to rain or moisture, does not operate

normally, or has been dropped.

Short-circuit

Breaker

Power Supply

Do not stick metal objects or any other conductive

material into the power cord. Do not touch the end

of the power cord while it is plugged in.

Keep the packing anti-moisture material or vinyl

packing out of the reach of children. Anti-moisture

material is harmful if swallowed. If swallowed by

mistake, force the patient to vomit and visit the

nearest hospital. Additionally, vinyl packing can cause

suffocation. Keep it out of the reach of children.

CAUTION concerning the Power Cord

(Can differ by country):

It is recommended that appliances be placed upon a

dedicated circuit; that is, a single outlet circuit which

powers only that appliance and has no additional

outlets or branch circuits. Check the specification

page of this owner’s manual to be certain. Do not

connect too many appliances to the same AC power

outlet as this could result in fire or electric shock. Do

not overload wall outlets. Overloaded wall outlets,

loose or damaged wall outlets, extension cords,

frayed power cords, or damaged or cracked wire

insulation are dangerous. Any of these conditions

could result in electric shock or fire. Periodically

examine the cord of your appliance, and if its

appearance indicates damage or deterioration,

unplug it, discontinue use of the appliance, and have

the cord replaced with an exact replacement part by

an authorized service. Protect the power cord from

physical or mechanical abuse, such as being twisted,

kinked, pinched, closed in a door, or walked upon.

Pay particular attention to plugs, wall outlets, and

the point where the cord exits the appliance. Do not

move the TV with the power cord plugged in. Do

not use a damaged or loose power cord. Be sure do

grasp the plug when unplugging the power cord. Do

not pull on the power cord to unplug the TV.

Short-circuit

Breaker

Power Supply

Warning

- To reduce the risk of fire or electrical shock, do

not expose this product to rain, moisture or other liquids.

Do not touch the TV with wet hands. Do not install this

product near flammable objects such as gasoline or

candles, or expose the TV to direct air conditioning.

Short-circuit

Breaker

Power Supply

Do not expose to dripping or splashing and do not place

objects filled with liquids, such as vases, cups, etc. on or

over the apparatus (e.g. on shelves above the unit).

Short-circuit

Breaker

Power Supply

Grounding

(Except for devices which are not grounded.)

Ensure that you connect the earth ground wire to

prevent possible electric shock (i.e. a TV with a three-

prong grounded AC plug must be connected to a three-

prong grounded AC outlet). If grounding methods are not

possible, have a qualified electrician install a separate circuit

breaker. Do not try to ground the unit by connecting it to

telephone wires, lightening rods, or gas pipes.

Short-circuit

Breaker

Power Supply

DISCONNECTING DEVICE FROM THE MAIN POWER

Mains plug is the disconnecting device. The plug must

remain readily operable.

As long as this unit is connected to the AC wall outlet, it is

not disconnected from the AC power source even if the

unit is turned off.

Do not attempt to modify this product in any way without

written authorization from LG Electronics. Unauthorized

modification could void the user’s authority to operate this

product.

ANTENNAS Outdoor antenna grounding

(Can differ by country):

If an outdoor antenna is installed, follow the

precautions below. An outdoor antenna system

should not be located in the vicinity of overhead

power lines or other electric light or power circuits,

or where it can come in contact with such power

lines or circuits as death or serious injury can occur.

Be sure the antenna system is grounded so as to

provide some protection against voltage surges

and built-up static charges. Section 810 of the

National Electrical Code (NEC) in the U.S.A. provides

information with respect to proper grounding of the

mast and supporting structure, grounding of the

lead-in wire to an antenna discharge unit, size of

grounding conductors, location of antenna discharge

unit, connection to grounding electrodes and

requirements for the grounding electrode.

Antenna grounding according to the National

Electrical Code, ANSI/NFPA 70

Short-circuit

Breaker

Power Supply

NEC: National Electrical Code

Ground Clamp

Antenna Lead in Wire

Antenna Discharge Unit

(NEC Section 810-20)
Grounding Conductor

(NEC Section 810-21)

Power Service Grounding

Electrode System

(NEC Art 250, Part H)

Electric Service

Equipment

Ground Clamp

Cleaning

When cleaning, unplug the power cord and wipe

gently with a soft cloth to prevent scratching. Do

not spray water or other liquids directly on the TV

as electric shock may occur. Do not clean with

chemicals such as alcohol, thinners or benzine.

Moving

Make sure the product is turned off, unplugged and

all cables have been removed. It may take 2 or more

people to carry larger TVs. Do not press or put stress

on the front panel of the TV.

ENG

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

Ventilation

Install your TV where there is proper ventilation. Do

not install in a confined space such as a bookcase.

Do not cover the product with cloth or other

materials while plugged. Do not install in excessively

dusty places.

If you smell smoke or other odors coming from the

TV, unplug the power cord and contact an authorized

service center.

Do not press strongly upon the panel with a hand or

a sharp object such as a nail, pencil or pen, or make a

scratch on it.

Keep the product away from direct sunlight.

Short-circuit

Breaker

Power Supply

Never touch this apparatus or antenna during a

thunder or lightning storm.

When mounting a TV on the wall, make sure not to

install the TV by hanging the power and signal cables

on the back of the TV.

Do not allow an impact shock or any objects to fall

into the product, and do not drop anything onto the
screen.

Dot Defect

The LCD panel is a high technology product with

resolution of two million to six million pixels. In a

very few cases, you could see fine dots on the

screen while you’re viewing the TV. Those dots are

deactivated pixels and do not affect the performance

and reliability of the TV.

Generated Sound

“Cracking” noise: A cracking noise that occurs

when watching or turning off the TV is generated by

plastic thermal contraction due to temperature and

humidity. This noise is common for products where

thermal deformation is required.

Electrical circuit humming/panel buzzing: A low level

noise is generated from a high-speed switching

circuit, which supplies a large amount of current

to operate a product. It varies depending on the

product.

This generated sound does not affect the

performance and reliability of the product.

Take care not to touch the ventilation openings.

When watching the TV for a long period, the

ventilation openings may become hot. This does

not affect the performance of the product or cause

defects in the product.

If the TV feels cold to the touch, there may be a small

“flicker” when it is turned on. This is normal, there

is nothing wrong with TV. Some minute dot defects

may be visible on the screen, appearing as tiny red,

green, or blue spots. However, they have no adverse

effect on the TV’s performance. Avoid touching the

LCD screen or holding your finger(s) against it for

long periods of time. Doing so may produce some

temporary distortion effects on the screen.

DISPOSAL (Hg lamp only used in LCD TVs)

The fluorescent lamp used in this product contains a small

amount of mercury. Do not dispose of

this product with general household waste. Disposal of this

product must be carried out in accordance to the regulations

of your local authority.

Preventing “Image burn” or “Burn-in” on your TV screen

If a fixed image displays on the TV screen for a long

period of time, it will be imprinted and become a

permanent disfigurement on the screen. This is “image

burn” or “burn-in” and not covered by the warranty.

If the aspect ratio of the TV is set to 4:3 for a long period

of time, image burn may occur on the letterboxed area of

the screen.

Avoid displaying a fixed image on the TV screen for a

long period of time (2 or more hours for LCD, 1 or more

hours for the Plasma TV) to prevent image burn.

For USA and Canada

FCC NOTICE

This equipment has been tested and found

to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable

protection against harmful interference in a

residential installation. This equipment generates,

uses and can radiate radio frequency energy and,

if not installed and used in accordance with the

instructions, may cause harmful interference

to radio communications. However, there is

no guarantee that interference will not occur in

a particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by turning

the equipment off and on, the user is encouraged

to try to correct the interference by one or more

of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the

equipment and the receiver.

- Connect the equipment to an outlet on a circuit

different from that to which the receiver is

connected.

- Consult the dealer or an experienced radio/TV

technician for help.

This device complies with part 15 of the FCC

Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful

interference and (2) this device must accept any

interference received, including interference that

may cause undesired operation of the device.

Any changes or modifications in construction of

this device which are not expressly approved by

the party responsible for compliance could void

the user’s authority to operate the equipment.

NOTE TO CABLE/TV INSTALLER

This reminder is provided to call the CATV system

installer’s attention to Article 820-40 of the

National Electric Code (U.S.A.). The code provides

guidelines for proper grounding and, in particular,

specifies that the cable ground shall be connected

to the grounding system of the building, as close

to the point of the cable entry as practical.

ENG

ENGLISH

TABLE OF CONTENTS / INSTALLATION MENU

TABLE OF CONTENTS

IMPORTANT SAFETY INSTRUCTIONS

TABLE OF CONTENTS

INSTALLATION MENU

ENTERING THE INSTALLATION MENU

PUBLIC DISPLAY SETUP

TV LINK-LOADER

Changing the Password

Set ID Setup (LT560H, LT360C Only)

Configuration setup

Pro:Centric (LT560H Only)

TV LINK-LOADER KEY FUNCTIONS

DOWNLOAD A SPLASH IMAGE

INSTALLATION MENU

Your TV's OSD (On Screen Display) may differ
slightly from that shown in this manual.

ENTERING THE

INSTALLATION MENU

The feature set up available on this LG
commercial TV which is equipped with ‘TV link’
as shown on the ‘Installation Menu ’. This simple
menu is designed to make it easy and efficient
for the system integrator to install and set up the
institution’s communications system.
Public Display Mode controls operation and
functionality of the TV. Once set up, these settings
are clonable; they can be copied and transferred
to another identical TV. See the TV Link-Loader
section for cloning details.

Accessing the Installation Menu

with the SETTINGS Button

With an LG installer remote, press and hold

down the

SETTINGS

button for five seconds.

The TV screen will show the Channel on-
screen display in the upper-left corner.

Key in “1-1-0-5” and press the

button. This

is the default password. The password can be
changed if desired.

ENG

ENGLISH

INSTALLATION MENU

PUBLIC DISPLAY SETUP

Refer to the PDM menu options as described
below and on the following page. Then set the
options to your requirements.

Use the v or ^ or < or > button to select

desired menu option.

Use the

button to return to previous menu.

Use the

button to exit menu.

Installation Menu (V 2.6)

Public Display Settings

TV Link-Loader
Password Change
Set ID Setup
Configuration Setup
Pro:Centric

ImageyshownymayydifferyfromyyouryTV

Public Display Mode Menu Items

Public Display Settings

ꔊ

Yes

ꔋ

Yes

Virtual

AV1

Enable

100

•

Public Display Mode

•

Power On Defult

•

Input Source

•

Tune Mode

•

Major

•

Minor

•

Aux Source Setting

•

Input Source

•

Setting

•

Minimum Volume

•

Maximum Volume

•

Start Volume

•

Level

•

Power Management

•

Setting

•

Key Management

•

Factory Reset

•

Aspect Ratio

ꕣ

Public Display Mode

If ‘Public Display Mode’ is set to Yes (Enabled), all
functions of the Public Display Settings are active.
If ‘Public Display Mode’ is set to No (Disabled), all
functions of the Public Display mode are not active.

Power On Default

This function allows you to determine the initial channel
number and external input when the TV is turned
On. This feature is useful for an in-house information

Accessing the Public Display Mode

Use the

v or ^

button to select the Public

Display Settings option and press the

button.

Once in the Public Display Settings menu,

use the

v ^

< > button to select and adjust

the menu options to your requirements. If you
want Public Display mode to be enabled, select
‘Yes’ for that option.

Installation Menu (V 2.6)

Public Display Settings

TV Link-Loader
Password Change
Set ID Setup
Configuration Setup
Pro:Centric

ImageyshownymayydifferyfromyyouryTV

Accessing the Public Display Mode

Menu by pressing and holding

down ENTER Button* on the TLL-

1100A Cloner

Press and hold the ENTER button for more that

5 seconds. The TV will automatically display
the Installation Menu after about 5-7 seconds.

* The TLL-1100A TV Link-Loader is not supplied
with this TV.

ENG

ENGLISH

INSTALLATION MENU

channel, since the TV would always select that channel
when it is turned On. When set to No, the TV starts on
the channel it was on before turning off.

Aux Source Setting

The Aux Source Setting feature will enable or
disable each external input. This data will be
retained in non-volatile memory and will survive a
power loss.

Minimum Volume

This function determines the minimum volume level
allowable with the VOLUME (VOL) Up/Down control. In
this way, for example, someone cannot set the volume
too low to hear. The value range is from 0 to 100 —
change values with ADJ Left/Right arrow. The factory
default is 0, which provides the full range of volume
control, if item 009 MAX VOLUME is also set to 100. It
may be best to set the same value on every TV.

NOTE

: The minimum volume level cannot have a value

setting higher than the MAX VOLUME level (described
below).

Maximum Volume

This function determines the maximum volume
level allowable with the VOLUME (VOL) Up/Down
controls. In this way, for example, someone can not
set the volume level high enough to disturb others.
The value range is 0 to 100, with 100 as the default,
which gives the user the full range of volume control,
if item 008 MIN VOLUME is also set at 0. Change
values with ADJ Left/Right arrow keys. It may be
best to set the same value on every TV.

NOTE

: The maximum volume level cannot have a

value setting lower than the MIN VOLUME level
(described previously).

Start Volume

This function allows the Installer to determine
the initial volume level setting when the TV is
turned ON. This feature is useful for an in-house
information channel, since the TV would always
select that Volume level when it is turned on. The
range of values are 0 - 100. If No is selected, the
current volume level will be retained in memory
when the TV is turned Off. At TV turn On, Volume
level is automatically set to the previous level.
Setting is retained in non-volatile memory.

Power Management

Determines hours of no activity before automatic
shutoff. The POWER MANAGE function is for
saving energy. If set to No, Power Manage is
disabled. Settings range from 1 ~ 7, representing
the hours that the unit will remain On, unless
there has been activity from either the control
panel or remote control. Setting is retained in non-
volatile memory.

Key Management

If set to 1, key defeat prevents the end user from
accessing the on-screen menus with the display
front panel, and < or > button do not function. If
set to 0, those keys do function.
Note: The menus can always be accessed by
pressing SETTINGS button on the remote.
Key management when enabled determines
the level of control that the guest has over the
television. Key management has five modes:
(default is ‘0’)

0 = Television is unrestricted and responds to

all commands.

1 = Key defeat ”prevents the television from

responding to “SETTINGS”key presses on
the front panel.

2 = “Key Lock ”prevents the television from

responding to any front panel key press.

3 = “System provider”mode allows access to

the menu system from the front panel or
remote control but access is controlled as
follows

* Accessible items on the menu system
- Main/PIP input select screens
- Sleep Timer
- Aspect Ratio
- Closed Caption
- Full access “Lock”

→y

Q.menu, related to “Setup Menu”, is not
accessible either.

4 = “Key defeat” prevents the TV from

responding to a “SETTINGS” button
pressed on the front panel and remote
control.

5 = “No access Remote/Front panel” prevents

the TV from responding to any button
pressed on the front panel and remote
control.

NOTE

: You must set the Auto Off option to

off in the Time menu to prevent the TV set
from being turned off automatically.

Setting is retained in non-volatile memory.

Factory Reset

Set to 0 for normal.
Set to 1 to load presets to all of the previous item
settings and exit menu.
WARNING: Setting this to 1 will reload the factory
defaults.
Setting is retained in non-volatile memory.

ENG

ENGLISH

INSTALLATION MENU

TV LINK-LOADER

Using the TV Link-Loader along with the USB
cloning procedure, an Installer can quickly set up
and clone multiple TV sets at a property. These
cloned TVs will all have the same Master TV
Setup: Public Display Mode Installation Menu
settings, User A/V settings and the Channel Map.
This newer procedure significantly decreases
the installation time that would be necessary if the
standard RS-232C method were used instead.

Receive from USB

* USB Restriction: NTFS format is not supported.

Plug USB memory card into the USB port of the TV.

Use the v or ^ button to select the

TV Link-

Loader

option and then press the

button.

Installation Menu (V 2.6)

Public Display Settings

TV Link-Loader

Password Change
Set ID Setup
Configuration Setup
Pro:Centric

ImageyshownymayydifferyfromyyouryTV

Use the v or ^ button to select the

Receive

from USB

and press the

button.

• Below explains the naming rules for .TTL files

The supported model line will be in the name
of the file but the screen size will be listed as
"xx".
This allows TVs having the same chassis
model number to use the same ‘*.TTL’ file
without regard to the screen size.
ex) The name of ‘*.TTL’ file is ‘xxLH200C-
UA00000.TLL’ for 32/37/42LH200C model.

TV Link-Loader

Receive from USB

Send to USB
TV Link-Loader

ꕣ

ImageyshownymayydifferyfromyyouryTV

Aspect Ratio

Selects default aspect ratio at power up, see
settings below.
Set to 0 to disable. Aspect Ratio will stay at
previous state.
Set to 1 “Set By Program”.
Set to 2 for 4:3.
Set to 3 for 16:9.
Setting is retained in non-volatile memory.

Level

The level means start volume level. (0 ~ 100)

Setting

The setting is a value between 1 and 7
corresponding to the number of hours desired.

Item

Enable

Disable

Initial

Public Display Mode

Yes

Power On default

Yes

Input Source

TV-MAX_INPUT

Tune Mode

Virtual/Physical

Physical

Major No.

Subject to Ch. Type

Minor No.

Subject to Ch. Type

Aux Input Source Setting

Yes

Input Source

Aux Input (AV1-Max_Input)

AV1

Setting

Enable / Disable

Enable

Minimum Volume

0 ~ 100

Maximum Volume

0 ~ 100

100

Start Volume

Yes

Level

0 ~ 100

Power Management

Yes

Setting

1 ~ 7

Key Management

0 ~ 5

Factory Reset

0 ~ 1

Aspect Ratio

0 ~ 3

ENG

ENGLISH

INSTALLATION MENU

Use the v or ^ button to select the desired

*.TTL

files name and press the

button.

Receive from USB

xxLH200C-UA00001.TLL

xxLH200C-UA00002.TLL
xxLH200C-UA00003.TLL

ꕣ

The TV is changed to Standby mode after a

successful download. If the download failed, the
TV will changed to the initial installation screen.

Send to USB

* USB Restriction: NTFS format is not supported.

Plug the USB memory card into the USB port

of the TV.

Use the v or ^ button to select the

TV Link-

Loader

option and then press the

button.

Installation Menu (V 2.6)

Public Display Settings

TV Link-Loader

Password Change
Set ID Setup
Configuration Setup
Pro:Centric

ImageyshownymayydifferyfromyyouryTV

Use the v or ^ button to select the

Send to

USB

and press the

button.

TV Link-Loader

Receive from USB

Send to USB

TV Link-Loader

ꕣ

Use the v or ^ button to select the desired file

name and press the

button.

Send To USB

Select the file name and press OK to start

ꔠ

ꔡ

xxLH200C-UA00001.TLL

ꕣ

The TV is changed to the initial installation

screen after a successful download.

TV Link-Loader

(LT560H, LT360C Only)

The TLL-1100A TV Link-Loader is not supplied
with this TV. It is available for purchase from your
LG dealer as an optional item. See your LG dealer.
The TV Link-Loader allows a Master TV setup
with Public Display Mode Setup to be copied
and transferred into another identical TVs. Once
copied into another identical TV, the Target TV will
function exactly like the original.

Note

: Please see TLL-1100A Installation and

Operating Guide for complete TV Link-Loader
Setup and Cloning Operating Instructions.

Connections

Connect the MPI cord provided with the TLL-

1100A TV Link-Loader into the TV RS-232C
port.

Connect the other end of the cable with the

stereo mini-plug into the RS-232C input port
which is located on the right side of the Link-
Loader.

On-Off Switch

Just below the RS-232C input on the Link-

Loader is the On-Off Switch. Set the switch to
the On position. TV Link-Loader must be set to
“ComLite System Mode”.

TV Link-Loader Setup

Press and hold the

ENTER

button until the TV

Link Loader LCD display changes from “Ready”
to “Mode in”.

Installation Menu (V 2.6)

Public Display Settings

TV Link-Loader

Password Change
Set ID Setup
Configuration Setup
Pro:Centric

ImageyshownymayydifferyfromyyouryTV

ENG

ENGLISH

INSTALLATION MENU

Changing the Password

If security for the system is a critical issue, the
password can be changed.

Use the v or ^ button to select the

Password

Change

option and then press the

button.

If the password is incorrect, the TV will
return to the installation menu (This feature
is not available for all models).

Key in a new four number password, key in the

password again for confirmation.

The password cannot be “8-7-4-1”. That
sequence of numbers is used to enter the
calibration menu (This feature is not available
for all models).

Password Change

New Password

Confirm Password

* *

* * *

Set ID Setup
(LT560H, LT360C Only)

Use the v or ^ button to select the

Set ID

Setup

option and then press the

button.

Select

Yes

to enable

Set ID Lock

disable

Set ID Lock

Key in a set ID number 1 ~ 99.

Set ID Setup

Set ID Lock

Set ID

◀

Yes

▶

ꕣ

Use the v or ^ button to select the

TV Link-

Loader

option and then press the

button.

‘Ready to Process’ display will appear on the
TV screen.

TV Link-Loader

Receive from USB
Send to USB

TV Link-Loader

Press the

SEND

RECEIVE

button to put the

Link-Loader into Send or Receive mode

Receiving Master TV Setup Data

The LCD will show Receive. Press the ENTER
button to begin receiving. The LCD will show
0XX Prg the progress bar. Check the TV
Volume OSD to show receiving progress. The
Link-Loader will record the TV setup data in its
internal memory. If an error occurs, press the
RECEIVE button to cancel receiving.

Sending Master TV Setup Data

When IR Send or RS Send appears on the
LCD, press ENTER. The Link-Loader will
transfer the TV setup data in its internal
memory to the Target TV. If an error occurs,
press SEND button to cancel sending. After
the transfer is complete, the OSD is removed
from the screen and the TV turns off. TV turn
off indicates that the transfer is complete.

* Refer to the TLL-1100A User’s Manual for more
detailed information.

ꕣ

ENG

ENGLISH

INSTALLATION MENU

Pro:Centric (LT560H Only)

Use the v or ^ button to select the

Pro:Centric

option and then press the

button.

Make appropriate adjustments.

(1) Mode

Sets whether or not enable Pro:Centric and the
service method.
You can set to Off, Flash or GEM using the
< or > button. The default value is Off; when it
is set to Off, all the sub items are disabled.

(2) Receive Data

Sets Enable or Disable. When it is set to
Disable, all the sub items are disable.

(3) RF Type

Sets the RF type to Air or Cable.

(4) Channel Number

Sets the number of physical channel, The
default value is 2 (Range: 1 - 135).

Pro:Centric

Mode

Receive Data

RF Type

Channel Number

◀

Off

▶

Enable

Air

ꕣ

Configuration setup

Select RCU (Remote Control Unit)

It is a mode to set whether to use Select
RCU or not. When ‘Select RCU’ is set to
‘Enable’, You can adjust the ‘Number of
RCU’ menu.

Number of RCU

It is a mode to set the Number of RCU.
Number of RCU value range 1 ~ 9 (When
‘Select RCU’ is set to ‘Enable’)
Number of RCU value range 0 (When ‘Select
RCU’ is set to ‘Disable’)

* RCU (Remote Control Unit): It is special RCU

that operates only a set number of RCU in the
TV.

Splash Offset Time

Sets the splash image display time.

The time can be set to between 0 and 10
seconds.

USB Auto Playback (LT360C, CS460C Only)

Select Enable to use USB Auto Playback
functionality.

This function makes TV to search and play
the USB's movie files located at the first slot
and partition and root(top) directory if USB is
plugged-in.

ImageyshownymayydifferyfromyyouryTV

Configuration Setup

Select RCU

Number of RCU

Splash Offset Time

USB Auto Playback

Enable

Disable

ENG

ENGLISH

INSTALLATION MENU

TV LINK-LOADER KEY FUNCTIONS

(See Users Manual for Key Functions)

TV LINK

Loader

TLL 1100A

Ready

MODE

MENU

RECEIVE

SEND

ENTER

LCD FUNCTION DISPLAY WINDOW

Shows the current operating function.

MODE

Selects ‘Ready’ and ‘Mode In’ functions.

MENU

Brings up the main menu to the screen.

Enters or exits menus and submenus.

UP/DOWN/LEFT/RIGHT/ENTER

Use to navigate menus and submenus.

ENTER

: Functions like an OK key on a regular remote

control.

: Channels Up.

Down

: Channels Down.

Left

: Controls Volume Down.

Right

: Controls Volume Up.

SEND

Refer to the Users Manual for SEND key functions.

Send key functions change depending on operating

mode.

RECEIVE

Refer to the Users Manual for RECEIVE key functions.

Receive key functions change depending on operating

mode.

ENG

ENGLISH

INSTALLATION MENU

DOWNLOAD A SPLASH IMAGE

How to Download a Splash Image file to the Display

Make a ‘LG_DTV’ folder on the USB flash drive and then copy the splash image file to that folder.

Connect the USB device to the USB IN jack on the TV.

USB IN

AV IN 2

VIDE

AUDI

L/MON

ANTENNA/

CABLE IN

RGB IN (PC)

AUDIO IN

(RGB/DVI)

RS-232C IN

(CONTROL & SERVICE)

OPTICAL

DIGITAL

AUDIO OUT

VIDEO

AUDIO

L/MONO

VIDEO

AUDIO

COMPONENT IN

AV IN 1

/DVI IN

USB IN

AV IN 2

VIDE

AUDI

L/MON

ANTENNA/

CABLE IN

RGB IN (PC)

AUDIO IN

(RGB/DVI)

RS-232C IN

(CONTROL & SERVICE)

OPTICAL

DIGITAL

AUDIO OUT

VIDEO

AUDIO

L/MONO

VIDEO

AUDIO

COMPONENT IN

AV IN 1

/DVI IN

TV Software Upgrade(Expert)

The Following update files are found in the USB
device. Select the file you want to apply to update
this TV or press EXIT to cancel the update.

LOGO Image Download

TV Software Update

ENG

ENGLISH

INSTALLATION MENU

NOTE

Splash Image update function supports only JPEG format file of less than 1 MB filesize.

JPEG images with progressive encoding are not supported.

We recommend you that splash image resolution match the TV`s panel resolution.

Max resolution of splash image: Full HD -> 1920 x 1080, HD -> 1360 x 768.

The TV will keep the Splash image until you change it.

TV Software Upgrade(Expert)

[Curent TV Software Version Information]
EPK : 03.06.00

The following software files are found in the
memory card. Select the file you want to download
to this TV or Press EXIT to cancel the update.

EPK :

[ Forced Update Option ]

Ext. MICOM

SPI Boot

LOGO Image

usb-01.07.00.D4

usb-03.40.00.B5_47_55_ptc_v1.00.015

You can see a new Splash Image on TV which
you downloaded while turning on TV.

Select the Splash

Image file you want.

TV Software Upgrade

UPGRADING...

100%

Do not unplug!

Wait till the download process

is completed.
After completion of download,
TV set will restart automatically.

INPUT

VOL

ENTER

ENG

ENGLISH

INSTALLATION MENU

The model and serial number of the TV is

located on the back and/or one side of the TV.

Record it below should you ever need service.

MODEL

SERIAL

Ask a Question ?

PDF User Manual

32LT360C\ 42LT360C\ 32CS460C\ 42CS460C\ 37LT560H\ 42LT560H\ 26LT360C

Full Text Searchable PDF User Manual