Full Text Searchable PDF User Manual
USER鈥橲 MANUAL
SCANNER
www.lfxgroup.com
BARREL 250
KEEP THIS MANUAL FOR FUTURE NEEDS
For your own safety, please read this user manual carefully before installing the device.
Keep this device away from rain and moisture !
Unplug mains lead before opening the housing.
Every person involved with the installation, operation and maintenance of this device has to:
-be qualified
-follow carefully the instructions of this manual
INTRODUCTION:
Thank you for having chosen this professional moving head.
You will see you have acquired a powerful and versatile device.
Unpack the device. Inside the box you should find: the fixture device, a power cable, an
XLR connection cable, a safety cable and this manual. Please check carefully that there is no damage
caused by transportation. Should there be any, consult your dealer and don鈥檛 install this device.
Features
路
Pan movement: pan 156
掳
路
Tilt movement: tilt 45
掳
路
3 operation mode: DMX controlled, stand alone or sound activated via built in microphone
飥狅
銆
路
9 colors plus white, with two direction rainbow effect,
Switchable colour change (mode 1: only full colours, mode 2: colour-change at every position)
銆
飥
路
7
rotating gobos plus open, with different speed gobo shaking effect
銆
路
飥狅
strobe effect : 0~10 flashes per second or random strobe
飥狅
銆
路
8 preset programs selectable
路
Control board with 4-digit display and foil-keyboard for adjusting the DMX-starting address,
Pan/tilt-Reverse, Program, Reset, lamp on/off, operating hours and etc
銆
路
digital display can be turn 180掳 reverse to fit for different installation position
銆
路
local or remote resetting
銆
路
auto test for all functions
銆
路
value of each DMX-channel can be displayed
銆
路
飥
save program : edit and save the program to the incorporated EEPROM through the front control
panel or external controller; can save maximum 48 scenes, and run the saved program by the 鈥渞un鈥
menu from the front control panel
- 2 - WIT044 V1.6-03NR
SAFETY INSTRUCTIONS
CAUTION
Be very careful during installation. Since you will be working with a dangerous
voltage you can suffer a life-threatening electric shock when touching live wires.
This device has left the factory in perfect condition. In order to maintain this condition and to ensure
a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning
notes written in this user manual.
IMPORTANT
Damages caused by the disregard of this user manual are not subject to warranty.
The dealer will not accept liability for any resulting defects or problems.
If the device has been exposed to temperature changes due to environmental changes, do not switch
it on immediately. The arising condensation could damage the device. Leave the device switched off
until it has reached room temperature.
This device falls under protection-class I. Therefore it is essential that the device be earthed.
The electric connection must carry out by qualified person.
Make sure that the available voltage is not higher than stated at the end of this manual.
Make sure the power cord is never crimped or damaged by sharp edges. If this would be the case,
replacement of the cable must be done by an authorized dealer.
Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle
the power cord by the plug. Never pull out the plug by tugging the power cord.
During initial start-up some smoke or smell may arise. This is a normal process and does not
necessarily mean that the device is defective, it should decrease gradually.
- 3 - WIT044 V1.6-03NR
CAUTION
Never touch the device during operation!
The housing may heat up
CAUTION
Never look directly into the light source,
as sensitive persons may suffer an epileptic shock.
Please be aware that damages caused by manual modifications to the device are not subject to
warranty. Keep away from children and non-professionals.
GENERAL GUIDELINES
This device is a lighting effect for professional use on stages, in discotheques, theatres, etc.
This fixture is only allowed to be operated with the max alternating current which stated in the
technical specifications in the last page of this manual, the device was designed for indoor use only.
Lighting effects are not designed for permanent operation. Consistent operation breaks may ensure
that the device will serve you for a long time without defects. Do not shake the device.
Avoid brute force when installing or operating the device.
While choosing the installation-spot, please make sure that the device is not exposed to extreme heat,
moisture or dust. The minimum distance between light-output from the
projector and the illuminated surface must be more than 0,5 meter.
Always fix the fixture with an appropriate safety cable if you use the quick lock cam in hanging up
the fixture, please make sure the 4 quick lock fasteners turned in the quick lock holes correctly.
Operate the device only after having familiarized with its functions. Do not permit operation by
persons not qualified for operating the device. Most damages are the result of unprofessional
operation.
Please use the original packaging if the device is to be transported.
For safety reasons, please be aware that all modifications on the device are forbidden.
If this device will be operated in any way different to the one described in this manual, the product
may suffer damages and the guarantee becomes void. Furthermore, any other operation may lead to
short-circuit, burns, electric shock, lamp explosion, crash, etc.
- 4 - WIT044 V1.6-03NR
INSTALLATION INSTRUCTIONS
a) Installing or replacing the lamp
CAUTION
Only install the lamp with the device unplugged from the mains.
CAUTION
The lamp has to be replaced when it is damaged or deformed.
Before replacing the lamp let the lamp cool down, because during operation, the lamp can
reach very high temperature.
During the installation of halogen lamps do not touch the glass bulbs bare handed. Always use a
cloth to handle the lamps during insertion and removal.
Do not install lamps with a higher wattage. They generate higher temperatures than which the device
was designed for.
For the installation, you need one:
鈻
CDMT150 G12 lamp ;
飥狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅狅
鈻
鈭
MSD250/2 GY9.5 lamp ;
Procedure :
1
2
3
4
1) Unscrew the 2 screws on the back of the housing, holding the plate where the lamp is underneath.
2) Gently pull the socket holder using the knob in the middle.
3) Carefully insert the lamp into the socket. Please remember there is only one way to insert the lamp.
Gently slide the lamp and its lamp holder back into place and fasten the 2 screws.
4) On the access plate there are 3 small screws marked 1,2 and 3.which are used to adjust the lamp
holder in the lamp housing. You can adjust the 3 screws to fine-turn the position of the lamp to get
the maximum light output as shown below.
- 5 - WIT044 V1.6-03NR
Please remember the lamp is not a hot-restrike type, you must wait for approximately 10
minutes after having turned off the lamp before you can turn it back on again.
CAUTION
Do not operate this device with open cover
b) Mounting the device
CAUTION
Please consider the EN 60598-2-17 and the other respective national norms during the
installation. The installation must only be carried out by a qualified person.
The installation of the effect has to be built and constructed in a way that it can hold 10 times the
weight for 1 hour without any harming deformation.
The installation must always be secured with a secondary safety attachment, e.g. an appropriate
safety cable.
Never stand directly below the device when mounting, removing or servicing the fixture.
The operator has to make sure the safety relating and machine technical installations are approved by
an expert before taking the device into operation for the first time.
These installations have to be approved by a skilled person once a year.
CAUTION
Before taking into operation for the first time,
the installation has to be approved by an expert.
- 6 - WIT044 V1.6-03NR
Cautions:
The effect should be installed outside areas where persons may reach it, walk by or be seated.
CAUTION
When installing the device, make sure there is no highly
inflammable material within a distance of min. 0,5m
Overhead mounting requires extensive experience, including amongst others calculating
working load limits, installation material being used, and periodic safety inspection of all
installation material and the device. If you lack these qualifications, do not attempt the
installation yourself. Improper installation can result in bodily injury.
CAUTION
The electric connection must only be carried out by a qualified electrician.
Before mounting make sure that the installation area can hold a minimum point load of 10 times the
device鈥檚 weight.
Connect the fixture to the mains with the power plug.
installation via the Omega holders
Screw one clamp each via a M10 screw and nut directly into the bracket of the scanner. Pull the safety-chain
through the bracket of the base and over the trussing system or a safe fixation spot.
- 7 - WIT044 V1.6-03NR
DMX-512 control connection
Connect the provided XLR cable to the female 3-pin XLR output of your controller and the other
side to the male 3-pin XLR input of the moving head. You can chain multiple
Moving head together through serial linking. The cable needed should be two core, screened cable
with XLR input and output connectors. Please refer to the diagram below.
DMX-512 connection with DMX terminator
For installations where the DMX cable has to run a long distance or is in an electrically noisy
environment, such as in a discotheque, it is recommended to use a DMX terminator. This helps in
preventing corruption of the digital control signal by electrical noise. The DMX terminator is simply
an XLR plug with a 120
鈩
resistor connected between pins 2 and 3,which is then plugged into the
output XLR socket of the last fixture in the chain. Please see illustrations below.
Address 1 Address 9 Address 17
Projector DMX start address selection
All fixtures should be given a DMX starting address when using a DMX signal, so that the correct
fixture responds to the correct control signals. This digital starting address is the channel number
from which the fixture starts to 鈥渓isten鈥 to the digital control information sent out from the DMX
controller. The allocation of this starting address is achieved by setting the correct number on the
display located on the base of the device.
You can set the same starting address for all fixtures or a group of fixtures , or make different
address for each fixture individually.
If you set the same address, all the units will start to 鈥渓isten鈥 to the same control signal from the same
channel number. In other words, changing the settings of one channel will affect all the fixtures
- 8 - WIT044 V1.6-03NR
simultaneously.
If you set a different address, each unit will start to 鈥渓isten鈥 to the channel number you have set,
based on the quantity of control channels of the unit. That means changing the settings of one
channel will affect only the selected fixture.
In the case of the spot head, which is a 11 channel fixture, you should set the starting address of the
first unit to 1, the second unit to
9 (8 + 1), the third to 17 (9 + 8), and so on.
Note:
The odes
wn via the
m
of DMX 512 data and lamp are sho
display:
. .
.
.
Lamp on
Lamp on
DMX OK
DMX OK
NO DMX
NO DMX
Lamp off
Lamp off
1. After switching on, the device will automatically detect whether DMX 512 data is received or not. If the data is
received, the the display will show
"A.001"
with the actually set address. If there is no data received at the
DMX-input, the display will flash
"A001"
with the actually set address.
This situation can occur if:
- the 3 PIN XLR plug (cable with DMX signal from controller) is not connected with the input of the device.
- the controller is switched off or defective, if the cable or connector is defective or the signal wires are swap in the
input connector.
It鈥檚 necessary to insert the XLR termination plug (with 120 Ohm) in the last lighting in the link in order to ensure
proper transmission on the DMX data link.
2. If the lamp is on, the the display will show
"A00.1"
with the actually set address. If the lamp is off, the the
display will show
"A001"
with the actually set address.
Control Board
The Control Board offers several features: you can simply set the starting address, switch on and off the lamp, run
the pre-programmed program or make a reset.
The main menu is accessed by pressing the Mode/esc-button until the display starts flashing. Browse through the
menu by pressing the Up-button or Down-button. Press the Enter-button in order to select the desired menu. You
can change the selection by pressing the Up-button or Down-button. Confirm every selection by pressing the
Enter-button. You can leave every mode by pressing the Mode/esc-button . The functions provided are described in
the following sections.
- 9 - WIT044 V1.6-03NR
Default settings shaded.
VALU
A001~A511 (AXXX)
DMX address setting
ADDR
SLAV
ON/OFF (SLAV)
Slave setting
ALON (AU-A)
Automatic Run in Stand Alone
AUTO
MAST (AU-M)
Automatic Run as Master
ALON (SO-A)
Sound-controlled Run in Stand
Alone
RUN
SOUN
MAST (SO-M)
Sound-controlled Run as Master
VALU
D鈥揦X D-00 (DXXX)
Display the DMX 512 value of
each channel
RDIS
ON/OFF Reverse
display
0
MODE
DISP
CLDI
ON/OFF
Shut off LED display
RPAN
ON/OFF
Pan
Reverse
RTIL
ON/OFF
Tilt
Reverse
REST
Reset
LODA
ON/OFF
Restore factory settings
1
SET
VER V-1.0~V-9.9
Software
version
LADJ
ON/OFF Lamp
adjustment
2
ADJU
TEST
T鈥01~T鈥30
Test function of each channel
MATI
0000~9999(hours)
Fixture running time
LATI
0000~9999(hours)
Lamp running time
CLMT
ON/OFF
Clear fixture time
3
TIME
CLLT
ON/OFF
Clear lamp time
STEP
S鈥01 ~S鈥48
Steps of Program Run
C鈥01~C鈥30
0 1 XX(00~FFH)
3 0 XX(00~FFH)
Edit the channels of each scene
TIME T 鈥 鈥 X(1~9)
Time for each scene
4
EDIT
SC01
~ SC48
CNIN
ON/OFF
Edit program via controller
Main functions
- Main menu 0
1. Press
[MODE/ESC]
to enter the main menu
"MODE"
(display flashing)
- 10 - WIT044 V1.6-03NR
2. Press
[ENTER]
and select
"ADDR"
,
鈥淩UN鈥
or
"DISP"
by pressing
[UP]
or
[DOWN]
button.
3. Press
[ENTER]
for selecting the desired sub menu.
- DMX address setting, Slave setting
- DMX address setting
With this function, you can adjust the desired DMX-address via the Control Board.
1. Select
鈥淰ALU鈥
by pressing
[UP]
or
[DOWN]
button.
2. Press
[ENTER]
, adjust the DMX address by pressing
[UP]
or
[DOWN]
button.
3. Press
[ENTER]
to confirm or pressing
[MODE/ESC]
to return to main menu.
- Slave setting
With this function, you can define the device as slave.
1. Select
鈥淪LAV鈥
by pressing
[UP]
or
[DOWN]
button.
2. Press
[ENTER]
, the display shows
鈥淥N鈥
or
鈥淥FF鈥
.
3. Press
[UP]
to select
鈥淥N鈥
if you wish to enable this function or press [DOWN] to select
鈥淥FF鈥
if you don鈥檛.
4. Press
[ENTER]
to confirm or press
[MODE/ESC]
to return to main menu.
- Program Run, Master setting
With the function
"RUN"
, you can run the internal program. You can set the number of steps under Step. You can
edit the individual scenes under Edit. You can run the individual scenes either automatically (AUTO), i.e. with the
adjusted Step-Time or sound-controlled (SOUN). The selection "ALON" means Stand Alone-mode and "MAST"
that the device is defined as master.
1. Select
"AUTO"
or
"SOUN"
by pressing
[UP]
or
[DOWN]
button.
2. Press
[ENTER]
for selecting the desired extension menu.
3. Select
"ALON"
or
"MAST"
by pressing
[UP]
or
[DOWN]
button.
4. Press
[ENTER]
to confirm or Press
[MODE/ESC]
to return to the main menu.
- Display the DMX-value, Reverse display, Shut off LED display
- 11 - WIT044 V1.6-03NR
- Display the DMX 512 value of each channel
With this function you can display the DMX 512 value of each channel.
1. Select
"VALU"
by pressing
[UP]
or
[DOWN]
button.
2. Press
[ENTER]
to confirm; the display shows
鈥淒-00鈥
. In this setting, the DMX-adjustment of every
channel will be displayed.
3. Press
[UP]
or
[DOWN]
button in order to select the desired channel. If you select
鈥淒-14鈥
the display
will only show the DMX-value of the 14
th
channel.
4. Press
[ENTER]
to confirm or Press
[MODE/ESC]
to return to the main menu.
5. The display shows
"D- XX鈥
, 鈥漍鈥 stands for the DMX-value of the selected channel.
- Reverse display
With this function you can rotate the display by 180
掳
.
1. Select
"RDIS"
by pressing
[UP]
or
[DOWN]
button.
2. Press
[ENTER]
, the display shows
鈥淥N鈥
or
鈥淥FF鈥
.
3. Press
[UP]
to select
鈥淥N鈥
if you wish to enable this function or press
[DOWN]
button to
鈥淥FF鈥
if you
don鈥檛; the display will rotate by 180
掳
.
4. Press
[ENTER]
to confirm or Press
[MODE/ESC]
to return to the main menu.
- Shut off LED display
With this function you can shut off the LED display after 2 minutes.
1. Select
"CLDI"
by pressing
[UP]
or
[DOWN]
button.
2. Press
[ENTER]
, the display shows
鈥淥N鈥
or
鈥淥FF鈥
.
3. Press
[UP]
to select
鈥淥N鈥
if you wish to enable this function or press
[DOWN]
button to
鈥淥FF鈥
if you don鈥檛.
4. Press
[ENTER]
to confirm or Press
[MODE/ESC]
to return to the main menu.
- Main menu 2
1. Press
[MODE/ESC]
to enter the main menu (display flashing).
2. Press
[UP]
or
[DOWN]
button. to select
鈥淪ET鈥
.
- Pan Reverse
With this function you can reverse the Pan-movement.
1. Select
鈥淩PAN鈥
by pressing
[UP]
or
[DOWN]
button.
2. Press
[ENTER]
, the display shows
鈥淥N鈥
or
鈥淥FF鈥
.
3. Press
[UP]
to select
鈥淥N鈥
if you wish to enable this function or press
[DOWN]
button to
鈥淥FF鈥
if you don鈥檛.
4. Press
[ENTER]
to confirm or Press
[MODE/ESC]
to return to the main menu.
- Tilt Reverse
With this function you can reverse the Tilt-movement.
1. Select
鈥淩TIL鈥
by pressing
[UP]
or
[DOWN]
button.
2. Press
[ENTER]
, the display shows
鈥淥N鈥
or
鈥淥FF鈥
.
3. Press
[UP]
to select
鈥淥N鈥
if you wish to enable this function or press
[DOWN]
button to
鈥淥FF鈥
if you don鈥檛.
- 12 - WIT044 V1.6-03NR
4. Press
[ENTER]
to confirm or Press
[MODE/ESC]
to return to the main menu.
- Reset
With this function you can Reset the device via the Control Board.
1. Select
鈥淩EST鈥
by pressing
[UP]
or
[DOWN]
button.
2. Press
[ENTER]
, the display shows
鈥淥N鈥
or
鈥淥FF鈥
.
3. Press
[UP]
to select
鈥淥N鈥
if you wish to enable this function or
鈥淥FF鈥
if you don鈥檛.
4. Press
[ENTER]
to confirm or Press
[MODE/ESC]
to return to the main menu.
- Restore factory settings
With this function you can restore the factory settings of the device. All settings will be set back to the default
values (shaded). Any edited scenes will be lost.
1. Select
鈥淟ODA鈥
by pressing
[UP]
or
[DOWN]
button.
2. Press
[ENTER]
, the display shows
鈥淥N鈥
or
鈥淥FF鈥
.
3. Press
[UP]
to select
鈥淥N鈥
if you wish to enable this function or press
[DOWN]
button to
鈥淥FF鈥
if you don鈥檛.
4. Press
[ENTER]
to confirm or Press
[MODE/ESC]
to return to the main menu.
- Software version
With this function you can display the software version of the device.
1. Select
鈥淰ER鈥
by pressing
[UP]
or
[DOWN]
button.
2. Press
[ENTER]
, the display shows
鈥淰-X.X鈥
, 鈥淴.X鈥 stands for the version number, e.g. 鈥淰-1.0鈥, 鈥淰-2.6鈥.
3. Press
[MODE/ESC]
to return to the main menu.
- Main menu 3
1. Press
[MODE/ESC]
to enter the main menu (display flashing).
2. Press
[UP]
or
[DOWN]
button to select
鈥淎DJU鈥
.
- Lamp adjustment
With this function you can adjust the lamp via the Control Board. The shutter opens and the lamp can be adjusted.
In this mode, the device will not react to any control signal.
1. Select
鈥淟ADJ鈥
by pressing
[UP]
or
[DOWN]
button.
2. Press
[ENTER]
, the display shows
鈥淥N鈥
or
鈥淥FF鈥
.
3. Press
[UP]
to select
鈥淥N鈥
if you wish to enable this function or press
[DOWN]
button to
鈥淥FF鈥
if you don鈥檛.
4. Press
[ENTER]
to confirm or Press
[MODE/ESC]
to return to the main menu.
- Test function of each channel
With this function you can test each channel on its (correct) function. There are 8 DMX channels, and all except
channels 3, 7 and 8 can be tested.
1. Select
鈥淭EST鈥
by pressing
[UP]
button.
2. Press
[ENTER]
, the display shows
鈥淭-XX鈥
, 鈥淴鈥 stands for the channel number.
3. The current channel will be tested.
4. Select the desired channel by pressing
[UP]
or
[DOWN]
button.
5. Press
[ENTER]
to confirm or Press
[MODE/ESC]
to return to the main menu.
- 13 - WIT044 V1.6-03NR
- Main menu 4
1. Press
[MODE/ESC]
to enter the main menu (display flashing).
2. Press
[UP]
or
[DOWN]
button to select
鈥淭IME鈥
.
- Fixture running time
With this function you can display the running time of the device.
1. Select
鈥淢ATI鈥
by pressing
[UP]
or
[DOWN]
button.
2. Press
[ENTER]
, the display shows
鈥淴XXX鈥
, 鈥淴鈥 stands for the number of hours.
3. Press
[ENTER]
to confirm or Press
[MODE/ESC]
to return to the main menu.
- Lamp running time
With this function you can display the running time of the lamp.
1. Select
鈥淟ATI鈥
by pressing
[UP]
button.
2. Press
[ENTER]
, the display shows
鈥淴XXX鈥
, 鈥淴鈥 stands for the number of hours.
3. Press
[MODE/ESC]
to return to the main menu.
- Clear fixture time
With this function you can clear the running time of the device.
1. Select
鈥淐LMT鈥
by pressing
[UP]
or
[DOWN]
button.
2. Press
[ENTER]
, the display shows
鈥淥N鈥
or
鈥淥FF鈥
.
3. Press
[UP]
to select
鈥淥N鈥
if you wish to enable this function or press
[DOWN]
button to
鈥淥FF鈥
if you don鈥檛.
4. Press
[ENTER]
to confirm or Press
[MODE/ESC]
to return to the main menu.
- Clear lamp time
With this function you can clear the running time of the lamp. Please clear the lamp time every time you replace the
lamp.
1. Select
鈥淐LLT鈥
by pressing
[UP]
or
[DOWN]
button.
2. Press
[ENTER]
, the display shows
鈥淥N鈥
or
鈥淥FF鈥
.
3. Press
[UP]
to select
鈥淥N鈥
if you wish to enable this function or press
[DOWN]
button to
鈥淥FF鈥
if you don鈥檛.
4. Press
[ENTER]
to confirm or Press
[MODE/ESC]
to return to the main menu.
- Main menu 5
1. Press
[MODE/ESC]
to enter the main menu (display flashing).
2. Press
[UP]
or
[DOWN]
button to select
鈥淓DIT鈥
.
- Define the number of steps in Run
With this function you can define the number of steps in the Program Run.
1. Select
鈥淪TEP鈥
by pressing
[UP]
or
[DOWN]
button.
2. Press
[ENTER]
, the display shows
鈥淪-XX鈥
, 鈥淴鈥 stands for the total amount of steps you want to save, so you
can call up to 48 scenes in
鈥淩UN鈥
. For example if the 鈥淴X鈥 is 05, it means that
鈥淩UN鈥
will run the first 5 scenes
- 14 - WIT044 V1.6-03NR
you saved in
鈥淓DIT鈥
.
3. Press
[ENTER]
to confirm or Press
[MODE/ESC]
to return to the main menu.
- Editing the channels of the individual scenes
With this function you can edit the program to be called up in
Run.
a) Editing via the Control Board
1. Select
鈥淪C01鈥
by pressing
[UP]
or
[DOWN]
button.
2. Press
[ENTER]
, the display shows
鈥淪CXX鈥
, 鈥淴鈥 stands
for the scene no. to be edited.
3. Change the scene no. by pressing
[UP]
or
[DOWN]
button.
4. Press
[ENTER]
, the display shows
鈥淐-X鈥
, 鈥淴鈥 stands for
the channel no. Such as
鈥淐-01鈥
, it means you are
editing channel 1 of the selected scene.
5. Select the channel no. you would like to edit by pressing
[UP]
or
[DOWN]
button.
6. Press
[ENTER]
to enter editing for the selected
channel ,the fixture reacts to your settings. The display shows
the DMX value of the edited channel. Such as 鈥 11XX鈥, it
stands for in the channel 11 of the editing scene, the DMX value
is XX , XX is a hexadecimal number value 鈥01-FF鈥.Adjust the
desired DMX value by pressing
[UP]
or
[DOWN]
button.
7. Press
[ENTER]
in order to edit other channels of this scene.
8. Repeat steps 5-9 until you finish setting all the DMX values
ompleted, the display will flash
[ENTER]
to edit the time needed, the display shows
ssing
[UP]
or
[DOWN]
button.
iting, the display will change to the next scene
3-14 to edit and other scenes, you can edit and save a maximum of 48 scenes.
enes can be called
) Editing via the external controller
er now.
button.
]
button.
ows
"ON"
.
lly downloaded the first scene.
nloaded.
efined under
鈥淪TEP鈥
and the scenes can be called
for all channels of this scene.
9. Once all the channels c
鈥淭IME鈥
10. Press
鈥渢--X鈥,鈥淴鈥 stands for the time needed to run the current scene,
value 鈥1-9鈥. For example, 鈥渢--2鈥 means you need 2 seconds to run the current scene.
11. Adjust the desired time by pre
12. Press
[ENTER]
to save the settings for the scene you are ed
automatically.
13. Repeat step
14. Press
[MODE/ESC]
to exit. The number of steps can be defined under
鈥淪TEP鈥
and the sc
up under
鈥淩UN鈥
b
Call up the first scene in your controll
1. Select
鈥淪C01鈥
by pressing
[UP]
or
[DOWN]
2. Press
[ENTER]
, the display shows
鈥淪C01鈥
.
3. Press
[ENTER]
, the display shows
鈥淐-01鈥
.
4. Select
"CNIN"
by pressing
[UP]
or
[DOWN
5. Press
[ENTER]
, the display shows
"OFF"
.
6. Press
[UP]
or
[DOWN]
button .the display sh
7. Press
[ENTER]
, the display shows
"SC02"
. You successfu
8.
Adjust the Step-time as described above under point 12.
9. Call up the second scene in your controller now.
10. Repeat steps 5-11 until all desired scenes are dow
11. Press
[MODE/ESC]
to exit. The number of steps can be d
up under
鈥淩UN鈥
- 15 - WIT044 V1.6-03NR
DMX channel麓s functions and their values :
hanne
- Color Wheel 1 :
C
l 1
0-12
Open / white
13-25
COL 1
26-38
COL 2
39-51
COL 3
52-64
COL 4
65-77
COL 5
78-90
COL 6
91-103
COL 7
104-116
COL 8
117-127
COL 9
128-187
Forward
188-193
No rotation
194-255
Backwards r
0-13
Open
14-27
Rot. go
28-41
Rot. gobo 2 (metal)
42-55
Rot. gobo 3 (metal)
56-69
Rot. gobo 4 (metal)
70-83
Rot. gobo 5 (metal)
84-97
Rot. gobo 6 (metal)
98-115
Rot. gobo 7 (metal)
116-135
Rot. gobo 1 (metal) s
136-155
Rot. gobo 2 (metal) shake
156-175
Rot. gobo 3 (metal) shake
176-195
Rot. gobo 4 (metal) shake
196-215
Rot. gobo 5 (metal) shake
216-235
Rot. gobo 6 (metal) shake
236-255
Rot. gobo 7 (metal) shake
C
l 3
0-7
No rotation
forwards gob
28-135
No rotation
136-255
Backwards g
s rainbow effect from fast to slow
ainbow effect from slow to fast
Channel 2 - Rotating gobos, cont. rotation :
bo 1 (metal)
hake
hanne
- rotating gobo rotation :
8-127
o rotation from fast to slow
1
obo rotation from slow to fast
- 16 - WIT044 V1.6-03NR
C
0-31
Shutter closed
32-63
Dimmer (close t
64-95
Strobe effect slow to fast
96-127
No function (shutter open)
128-159
Pulse-effect in sequences
160-191
No function (shutter open)
192-223
Random strobe effect slow
224-255
No function (shutter open)
C
l 6
(When the Channel 6 is Bar
0-7
No rotation
forwards Bar
28-135
No rotation
136-255
backwards b
Ch
l 7
0
max speed
max to min s
26-235
blackout by movem
236-245
blackout by all wheel ch
246-255
no function
Ch
l 8
0-19
colour change normal
20-39
colour change to any po
40-59
No function
60-79
No function
80-99
Motor reset
00-119
Internal prog
120-139
Internal program 2
140-159
Internal program 3
160-179
Internal program 4
180-199
Internal program 5
200-219
Internal program 6
220-239
Internal program 7
240-255
Internal program 8
hannel 4 - Shutter, strobe:
o open)
to fast
Channel 5 - PAN movement 8bit :
hanne
- TILT movement 8bit :
rel or Dish)
8-127
rel or Dish rotation from fast to slow
1
arrel or dish rotation from slow to fast
anne
- Speed pan/tilt movement:
5-225
peed
2
ent
anging
anne
鈥 reset, internal programs:
sition
1
ram 1
- 17 - WIT044 V1.6-03NR
Channe
鈥 reset, internal programs:(only use in ELC LAMP)
l 8
0-127
colour change normal &Dimmer 0%~100%
28-140
colour change to any position
141-153
Motor reset
154-166
Internal prog
167-179
Internal program 2
180-192
Internal program 3
193-205
Internal program 4
206-218
Internal program 5
219-231
Internal program 6
232-244
Internal program 7
245-255
Internal program 8
1
ram 1
- 18 - WIT044 V1.6-03NR
CLEANING AND MAINTENANCE
g the inspection:
o be tightly connected and must
2)
any deformations on the housing, color lenses, fixations and installation spots
1)
st not show any traces of wearing and must not rotate with
2)
power supply cables must not show any damage, material fatigue or sediments.
The following points have to be considered durin
1) All screws for installing the devices or parts of the device have t
not be corroded.
There must not be
(ceiling, suspension, trussing).
Mechanically moved parts mu
unbalances.
The electric
Further instructions depending on the installation spot and usage have to be adhered by a skilled
installer and any safety problems have to be removed.
CAUTION
Disconnect from mains before starting maintenance operation.
e recommend a frequent cleaning of the device. Please use a moist, lint- free cloth. Never use
ble parts inside the device except for the lamp. Please refer to the
genuine parts from your local dealer.
ECHNICAL SPECIFICATIONS
120VAC,50Hz;
鈻
208VAC,50Hz;
鈻
220VAC,50Hz;
鈻
鈭
230VAC,50Hz;
鈻
240VAC,50Hz;
e;
12KGS;
: errors and omissions for every information given in this manual excepted. All information
W
alcohol or solvents.
There are no servicea
instructions under 鈥淚nstallation instructions鈥.
Should you need any spare parts, please order
T
Power supply
:
鈻
98VAC,50Hz;
鈻
鈻
98VAC,50Hz;
鈻
120VAC,60Hz;
鈻
208VAC,60Hz;
鈻
220VAC,60Hz;
鈻
230VAC,60Hz;
鈻
240VAC,60Hz;
Power consumption :
max.
鈻
230W ,
鈻
鈭
400W
Lamp :
鈻
CDMT150 G12 socket, Metal Halid
鈻
鈭
MSD250 GY9.5 socket, Metal Halide;
Motors :
6 micro motors
Packing dimensions :
67x37x34cm
Net weight :
鈻
10.5KGS;
鈻
鈭
Gross weight:
鈻
12.5KGS;
鈻
鈭
14KGS;
Remark
is subject to change without prior notice.
- 19 - WIT044 V1.6-03NR
Circuit Schematic
L
A
M
P
B
A
L
L
A
S
T
IG
N
IT
E
R
T
H
E
R
M
O
S
T
A
T
FU
SE
C
A
P
T
R
A
N
S
F
O
R
M
E
R
P
O
W
E
R
A
C
1
0
V
A
C
2
0
V
F
A
N
GO
BO
MO
TO
R
GO
BO
RO
.M
OT
OR
CO
LO
RM
OT
OR
TIL
TM
OT
OR
PA
NM
OT
OR
ST
RO
BE
MO
TO
R
B
L
P
N
S
C
A
N
7
C
H
-B
0
1
B
S
C
A
N
7
C
H
-0
5
M
IN
I-
C
O
N
T
R
O
L
-0
4
B
Colo
r m
ag
neti
c s
ens
or
Li
g
h
t s
ensor
- 20 - WIT044 V1.6-03NR