PDF User Manual

  1. Home
  2. Manuals
  3. LF Illumination EF300 SERIES Installation Instructions Manual

LF Illumination EF300 SERIES Installation Instructions Manual

Made by: LF Illumination
Type: Installation Instructions Manual
Category: DJ Equipment
Pages: 2
Size: 0.68 MB

 

Download PDF User Manual



Full Text Searchable PDF User Manual



background image

EF300 SERIES TRIMMED

SIZE A RECESSED

INSTALLATION INSTRUCTIONS

* Risk of fire or electric shock. 
* Disconnect all power before installing or servicing.
* Installation Instructions for qualified electricians only.
* Install per National Electrical Code and local regulations.
* Read Installation Instructions completely before installation.
* Failure to follow Installation Instructions may void warranties.

THIS PRODUCT MUST BE INSTALLED IN

ACCORDANCE WITH THE APPLICABLE

INSTALLATION CODE BY A PERSON

FAMILIAR WITH THE CONSTRUCTION AND

OPERATION OF THE PRODUCT AND THE

HAZARDS INVOLVED.

C

US

®

Warnings:

Integral Accessible

LED Driver

LED 

Module

Suspension

Tie Down

Bracket

Ceiling

Material

Extruded Aluminum

Housing
Suspension &

Trim Strap

Extruded High Transmission

Acrylic Smooth Satin White Lens

Recessed Trimmed

Hanger Assembly

A

Extruded Aluminum

Fixture Housing

B

Optical Assembly

& Power Supply

C

Extruded Acrylic

Snap-in Lens

D

Aluminum

Spacer(s)

C

Hang 1/4-20 rod

or Wire Cable

Tie Down

- SUSPENDED HANGER ASSEMBLY:

1.

  SUSPEND HANGER ASSEMBLY IN PLACE using 1/4-20 all thread or wire cable tie downs.

 Suspension tie down bracket locations vary. Typically 6” from each end on each side of 
housing. 

2.

  When SETTING HANGER ASSEMBLY be sure that the top of the finished trim sets to the 

bottom of the finished ceiling height. 

See Fig 1

- EF300 HOUSING INSERT:

1.

  SLIDE FIXTURE HOUSING INTO HANGER ASSEMBLY and fasten into place using hardware 

provided.  Pre-set mounting locations match housing fastener strap. 

See Fig 1

.

 

2.  

Place 6” aluminum spacers provided in mounting kit to ensure proper housing to lens width 

when installing finished ceiling. The recommended placement of spacers is no more than four 
feet apart.

- OPTICAL ASSEMBLY AND POWER SUPPLY:

1.

  REMOVE APERTURE SPACERS, INSERT OPTICAL & POWER SUPPLY ASSEMBLY by inserting 

up into the housing cavity. There is a tension clip on each side of driver housing, squeeze/com-
press and push up past inner housing tabs and release. This will lock assembly into place 

See 

Fig 3

.

- EXTRUDED ACRYLIC LENS:

1.

  REMOVE APERTURE SPACERS AND SNAP-IN LENS once all housing and inner components 

have been set in place, wiring complete and mud-in finished. Gently push lens into housing until 
formed tabs snap-in to place.

ASSEMBLY NOTE:

 

The EF300 Recessed Series primarily consist of 4 major components 

A, B, C, and D. 

See Fig. 2 & Fig. 3.

 This system is designed for ease of installation. 

IT IS IMPORTANT TO READ INSTRUCTION SHEET COMPLETELY BEFORE INSTALLATION.

FIGURE 1

FIGURE 2

PAGE 1 OF 2

HEADQUARTERS
9200 Deering Avenue
Chatsworth CA 91311

 

Telephone: 818-885-1335
Toll Free: 855-885-1335
Fax: 818-576-1335

www.lfillumination.com

REV. 083116

©2016 LF ILLUMINATION LLC

We reserve the right to change or 
withdraw specifications without prior notice.

 


background image

Snap in lens

Locking 

Joiners

Channel

Extend the alignment/locking 
joiners mid way

Slide corresponding channels
together and fasten

1

2

A

B

Optical

Fastening

Tension Clips

Wire Cable

Tie Down

Housing Fastener

Strap

Recessed Trimmed

Hanger Assembly

A

Extruded Aluminum

Fixture Housing

B

Optical Assembly

& Power Supply

C

Extruded Acrylic

Snap-in Lens

D

End Cap

* Risk of fire or electric shock. 

* Disconnect all power before installing or servicing.

* Installation Instructions for qualified electricians only.
* Install per National Electrical Code and local regulations.
* Read Installation Instructions completely before installation.
* Failure to follow Installation Instructions may void warranties.

THIS PRODUCT MUST BE INSTALLED IN

ACCORDANCE WITH THE APPLICABLE

INSTALLATION CODE BY A PERSON

FAMILIAR WITH THE CONSTRUCTION AND

OPERATION OF THE PRODUCT AND THE

HAZARDS INVOLVED.

C

US

®

Warnings:

EXPLODED ASSEMBLY VIEW

:

The EF300 Recessed Series primarily consist of 4 major 
components A, B, C, and D. 

See Fig. 2 & Fig. 3.

 This system

is designed for ease of installation. 

FOR ASSEMBLY SEQUENCE SEE PAGE ONE.

CONNECTING FOR CONTINUOUS RUNS

(Trim or Trimless)

Loosen and extend internal connecting joiners half way and lock in position.
Slide corresponding channel onto exposed joiner and lock into place.

See Fig. 4 steps 1 & 2.

PAGE 2 OF 2

FIGURE 3

FIGURE 4

NOTE: ALL WORK MUST BE 
DONE WITH CIRCUIT OFF AND 
COMPONENTS SHOULD NOT BE 
INSTALLED WHEN FIXTURE IS 
ENERGIZED.

EF300 SERIES

SIZE A RECESSED

INSTALLATION INSTRUCTIONS

HEADQUARTERS
9200 Deering Avenue
Chatsworth CA 91311

 

Telephone: 818-885-1335
Toll Free: 855-885-1335
Fax: 818-576-1335

www.lfillumination.com

REV. 083116

©2016 LF ILLUMINATION LLC

We reserve the right to change or 
withdraw specifications without prior notice.