PDF User Manual

  1. Home
  2. Manuals
  3. HSY F107E User Manual

HSY F107E User Manual

Made by: HSY
Type: User Manual
Category: IP Access Controllers
Pages: 2
Size: 2.25 MB

 

Download PDF User Manual



Full Text Searchable PDF User Manual



background image

connection diagram:

Fingerprint Access Control System

User Manual 

Due to continuous update of our products

I.Product Overview and Installation Instruction

Applicable Models

Status light

Fingerprint-reading are

Keypad

Card-reading are

Doorbell

Rese

USB

Fixing hole

Operating Environment:

Room temperature: -20°C-+50°C

Relative humidity: 95%

Operating Voltage & Current:

Input DC: +12V

Standby current:≤60mA

Operating current:≤120m

Mounting screws

Set screw

II.Inputting Fingerprint

Suggested finger: index finger, middle finger or

ring finger instead of thumb or little finger

1)Correct method

Use the finger to evenly press

the center of fingerprint are

2)Wrong methods

Incomplete touch

Off cente

Turn sideway

Low position

Please input fingerprint correctly for verification,

and improper operation might

result in poor performance of this device

Ports & Wiring Diagram

Black

Wiring Diagram

Alarm Port 

Relay Output Connection Diagra

High level output in case of alar

Red

Power

 Alarm

Lock 

Red

 Black

Door open button

Gray

Blue

Orange

Purple

Yellow

Black

Pink

Light green

White

Green

Optional

Access controller

Optional

Note: negative pole 

of normally-closed 

to NC port;

normally-open

end to NO port

S.N.

Functions

Numeric keys

Tamper alarm

Reading head for data output

86mm box-type panel for installation

Built-in card reader

Dark-background fingerprint reader

User verification with fingerprint or card

Connect this device and breaker via NO, COM and NC

output to separate from internal circuit of this device.

Once relay gets closed, electric lock is released.

Contact output current:3A; 

please refer to right diagram.  

Connection Diagram

Access Control System  

 


background image

IV.Administrator Operation

4.Exit

3.Verification request succeeds

(while the blue light turns on)

2.Enter administrator password

 (initial password: 123456)

1.Press [*]and there is a

 beep while the red light turns on

Remarks: once verification request succeeds,

it is allowed to register administrator

and the initial password will be out of use.

Registering Administrator

5.Exit (by pressing [#])

4.Once registration request 

succeeds there is a long beep 

2.Press (*1)

 and the orange 

1.Enter administrator password

 verification request succeeds

 the blue light turns on

3.Register administrator via 

fingerprint twice or read card once)

Remarks:

1.It is allowed to register at most 5 administrators via fingerprint or card

2.In case administrator quantity reaches the maximum value, they will be

cleared according to serial number.

4.2 Missing Administrator Password

1.Power off this device

2.Power on tamper 

switch to give an

3.Enter initial password

 blue light turns on

4.Register administrator again

5.Exit (by pressing “#”)

V:Registering User

5.1 Register Users Automatically

4.Exit (by pressing “#”)

3.Once registration

request succeeds

2.Register administrator via

 fingerprint twice or read card once)

1.Enter administrator password 

the blue light turns on

5.2 Register Users by Adding Employee ID

5.Exit (by pressing “#”)

4.Once registration request

beep and the blue light blinks once

3.Register user via fingerprint

(input fingerprint twiceread card

 once or enter password twice)

2.Enter employee

 ID #(1~4 digits)

1.Enter administrator

Once verification request

 blue light turns on.

VI:User Operation

6.1 User Verification via Fingerprint or Card

1.Standby mode. 2.Input fingerprint

VII:Deleting Users
7.1 Delete a User

1.Enter administrator 

Once verification request

blue light turns on

2.Press [*2]

or enter administrator

3.Enter employee 

ID# input fingerprint

6.Exit (by pressing “#”)

4.In case of incorrect

 ID# fingerprint or card

there is two beeps and

5.In case the user

 is in use delete it.

is a long beep 

7.2 Delete All Users

1.Enter administrator 

request succeeds the 

2.Press [*2] or 

enter administrator

3.Enter

4.Delete all users

There is a long beep

 and the blue light 

5.Exit (by pressing “#”)

8.2 Setting Unlocking Time

1.Enter administrator 

request succeeds the

 blue light turns on

2.Press [*3]

and the orange 

3.Set unlocking time

(0~99 seconds

and press # to for confirmation)

4.Setup succeeds

There is a long beep

and the blue light blinks once

5.Exit

IX:Unpacking

Remarks

Rocket screwdriver

Specifications 

Description 

Device

Packaging box

Plastic plugs

Self-tapping screws
Screwdriver

Quantity

For mounting and fixing
For mounting and fixing

1.Enter administrator 

 verification(Once succeeds

the blue light turns on

2.Press [*9]

and the orange 

3.Set system

4.Exit (by 

VIII:Access Control System Management

8.1 System Settings

6.2 User Verification via Password

1.Standby mode

2.Enter employee ID

press # to for confirmation

and enter password

 verification request succeeds,

for verification.Once

 fingerprint or card(input

 password for verification

 succeeds, the

card or password 

 succeedsthere is a long 

 or read card.

 passwordfor

light turns on

light turns on

 password for 

verification Once verification 

 (by pressing [#])

light turns on

 for verification.Once

fingerprint or card(input 

 and theblue light blinks once

 and dismantle it

 alarm for 30 seconds

 (*123456)and the

 password

password for verification.

 succeeds the 

 or read card

 the red light turns on

light blinks once

blue light turns on

 password

(0000#)

blinks once

Note: 5 seconds have been set as factory default.

 (by pressing “#”)

3.Verification request succeed

(There is a long beep sound 

and the blue light blinks once.)

Verification request fails. 

(it beeps twice and the red light turns on.

Verification request fails.

 (it beeps twice and the red light turns on.)

3.Verification request succeed

(There is a long beep sound 

and the blue light blinks once.)

it beeps twice and the

 red light turns on

 There  and the blue 

password for verification

Once verification 

verification request 

Press [*90#] for menu 

initialization press [*91#] 

for system initialization

press [*92#] to delete 

administrator and then

 press [#] for confirmation.

pressing “#”)