Getronic GT915 Installation And User Manual

Download PDF User Manual

Full Text Searchable PDF User Manual

GT915/916/917/918

INSTALLATION AND USER MANUAL

Getronic S.r.l.

Via Calcinate No.12

21026 Gavirate (VA) Italy

Tel. +39 0332 756011

Fax + 39 0332 731162

www.gtalarm.it

SUMMARY

1.0 - GENERAL DESCRIPTION

Page 2

2.0 - INSTALLATION AND CONNECTIONS

Page 3

3.0 - CONNECTION DIAGRAM

Page 4

4.0 - INDICATOR COMMAND DIAGRAM

Page 5

5.0 - GT931 ULTRASONIC KIT CONNECTION(only for GT915)

Page 5

6.0 - CENTRAL DOOR LOCKING DIAGRAMS

Page 6

7.0 - SET FUNCTIONS

Page 8

8.0 - USER MANUAL

Page 11

9.0 - MAINTENANCE AND WARNINGS

Page 14

10.0 - COMPLIANCE DECLARATION

Page 15

11.0 - TECHNICAL DATA

Page 15

12.0 - WARRANTY CONDITIONS

Page 16

1.0 - GENERAL DESCRIPTION

GT916 is a compact remote controlled alarm system equipped with 2 GT888 handsets
with electronic key incorporated for the emergency disarming, with universal central door
locking command, back-up battery, perimetric protection for doors/boot/bonnet, engine
immobilisation and also small in size which help with the installation.

FUNCTIONS PROGRAMMABLE OF THE SYSTEM (SET FUNCTIONS):

- HANDSETS SELF-CODING
- RAPID TEST
- COMFORT CLOSING(where appicable)
- ACOUSTIC SIGNAL WHEN ARMING/DISARMING
- INDICATOR COMMAND
- DOOR SWITCH PULSING MANAGEMENT
- POSITIVE DOORS PIN SWITCH MANAGEMENT

OTHER FUNCTIONS:

- Double door locking
- PANIC function
- ANTI-HIJACK function
- CHECK CONTROL of occurred alarms and anomalies
- Emergency disarming by handset with electronic key incorporated

2.0 - INSTALLATION AND CONNECTIONS

WARNINGS:

- Complete a pre-installation check and disconnect the negative terminal of the vehicle’s
battery. .
- Before fixing the device, insert the installation loom connectors into the alarm and
screw the connector cover on.
- Place the alarm system in the engine compartment, away from direct sources of
water spray and high tension wiring.
- Solder and isolate all connections.

Connect the

BROWN

wire to the negative terminal of the vehicle’s battery (power supply

negative).

Connect the

RED

(general power supply) and

RED/WHITE

wires (indicator relay positive)

to the positive terminal of the vehicle’s battery with a 15A fuse.

Connect the

YELLOW

wire to an ignition switched live (+15/54) that remains live even

when the engine is being cranked.

ORANGE

wire (INDICATOR Command): if the INDICATOR COMMAND is

DISABLED

connect to the vehicle right indicators (or to the left). If the INDICATOR COMMAND function
is

ENABLED

with this wire is possible to command the indicators (only on the vehicles

equipped with this function - See the INDICATOR COMMAND diagram). For the connection
refer to the technical installation guides.

Connect the

ORANGE/BLACK

/wire (FEEDBACK) to the vehicle left (or right) indicator by

a diode(2 Amp) (see the INDICATOR COMMAND diagram).

Connect the

GREEN

wire to the switches for the boot and bonnet protection.

Connect the

GREEN/BROWN

wire to the original door pin switches. This alarm input is

set by default to manage the negative stable signals. It is possible to manage also the
vehicles original switches with negative impulsive signals(pulsing) enabling the Function
No.6 PULSING management. For the connection refer to the technical installation guides.
It is possible to manage also the positive stable signals enabling the Function No.7
Postive Door pin switch management.

Connect the

PINK

wire (Positive output when the alarm is armed - Max capacity 80 mA to

the PINK wire of modules or additional sensors (i.e. ultrasonic module).

Connect the

GREEN/BLACK

wire (alarm input by optional additional sensors) to the

GREEN/BLACK wire of the same (i.e. ultrasonic module).

Connect the

BROWN

wire

(Sec. 0,35mm²)

to the modules or additional sensors (i.e.

ultrasonic module).

The

RED/BROWN, RED/GREY, RED/BLUE, YELLOW/BROWN, YELLOW/GREY and YELLOW/

BLUE

wires are used to command the central door locking referring to the instuctions in

the technical installation guide.

WARNING:

- Always use 5 A fuses on the RED/BLUE and YELLOW/BLUE wires.
- The max. load to command the central door locking is 5 A. For example it is not
possible to drive directly No.4 GT71 actuators (see diagramNo. 5).

= FUSE TO
INSERT

LEGEND:

RED - Pos. 5A

GREEN/BROWN - Pos. 4A

RED/WHITE - Pos. 14A

ORANGE/BLACK - Pos. 10A

ORANGE - Pos. 1A

PINK - Pos. 6B

BROWN - Pos. 1B

YELLOW - Pos. 3A

+15/54

IGNITION

SWITCHED LIVE

BROWN - Pos. 7A

EARTH

+12V POSITIVE

15A

FUSE

GREEN/BLACK - Pos. 2B

RED/BROWN - Pos. 11A

YELLOW/BROWN - Pos. 6A

RED/GREY - Pos. 13A

YELLOW/GREY - Pos. 16A

YELLOW/BLUE - Pos. 15A

RED/BLUE - Pos. 12A

UNIVERSAL

CENTRAL

DOOR LOCKING

INDICATORS

GT931

ULTRASONIC

MODULE

DOORS

PIN SWITCH

MANUAL DISARMING

BY GT888

RED - Pos. 7B

BROWN - Pos. 4B

YELLOW - Pos. 8B

BLACK - Pos. 5B

WHITE - Pos. 9A

GREY - Pos. 17A

PASSIVE ENGINE
IMMOBILISATION

GREEN - Pos. 2A

BONNET

PIN SWITCH

3.0 - CONNECTION DIAGRAM

The

WHITE

and

GRE

Y wires (Max. capacity 7 mA) are used for the engine immobilisation

either on the diesel or petrol vehicles. Cut the ignition switched wire which supplies the
fuel pump or electrovalve (diesel vehicles). Connect the two wires one to the GREY wire
and the other to the WHITE one.
- Place the

LED/RECEPTACLE

on the dashboard (so that it is easily visible and accessible)

and join together the connector with the connector on the alarm loom.

Install the two ultrasonic sensors on the “A” pillars (see pic below). One either side of the
windscreen pointing towards a hypothetical point at the centre of the rear window and
ensure that between the ultrasonics and the rear window there are no objects (i.e. headrest).
Plug the ultrasonics connectors in the module paying attention to their colours: RED and
WHITE. Do not cut or lengthen the ultrasonics cables. Plug the 4 pin BLACK loom connector

in the module. The module can be placed under the dashboard on the driver’s side.
Sensitivity increases if you turn the adjuster clockwise and decreases if you turn the
screw anticlockwise. NOTE:
This operation is important as
you do not want to have false
alarms. To check that it is not
oversensitive,arm the alarm
and hit the front and rear
windows with your hand (care
should be taken not do
damage the windows).The
system should not generate
any beep and flashes of the
LED on the receptacle.

GT931

TRIMMER FOR THE

ULTRASONIC SENSITIVITY

ADJUSTMENT

RED

ALARM

CONNECTOR

WHITE

5.0 - GT931 ULTRASONIC MODULE CONNECTION (only x GT915)/917

4.0 - INDICATOR COMMAND DIAGRAM

- The ORANGE wire connection as mentioned below has to be carried out only if the
function No.5 INDICATOR COMMAND IS ENABLED.
- When the ORANGE/BLACK wire connection is made you must use a 1N4007 diode.

VEHICLE HAZARD

BUTTON

INDICATORS

VEHICLE

WIRE

ORANGE

RED

BROWN

GREEN

ORANGE/BLACK

CM14

ALARM

1N4007

DIODE

VEHICLE HAZARD

BUTTON

INDICATORS

VEHICLE

WIRE

ORANGE

ORANGE/BLACK

ALARM

1N4007

DIODE

DIAGRAM FOR THE HAZARD
BUTTON WITH NEGATIVE
COMMAND

DIAGRAM FOR THE HAZARD
BUTTON WITH POSITIVE
COMMAND

+30

RED/BLUE

5 AMP FUSES

YELLOW/BLUE

RED/GREY

YELLOW/GREY

RED/BROWN

YELLOW/BROWN

DIAGRAM No.4/A

(Unlocking = 1" - Locking = 1")

GT ALARM

LOCKING COMMAND

UNLOCKING COMMAND

DO NOT CONNECT

AND ISOLATE

DIAGRAM No.3

(Unlocking = 1" - Locking = 1")

GT ALARM

+30

YELLOW/GREY

RED/GREY

CENTRAL DOOR

POSITIVE COMMAND WHEN LOCKING

CUT

10 AMP FUSE

YELLOW/BROWN

YELLOW/BLUE

RED/BROWN

RED/BLUE

POSITIVE COMMAND WHEN UNLOCKING

LOCKING ACTUATORS

COMMAND
BUTTON

6.0 - CENTRAL DOOR LOCKING DIAGRAMS

RED/BLUE

5 AMP FUSES

YELLOW/BLUE

RED/GREY

YELLOW/GREY

RED/BROWN

YELLOW/BROWN

DIAGRAM No.4/B

(Unlocking = 1" - Locking = 1")

GT ALARM

LOCKING COMMAND

UNLOCKING COMMAND

DO NOT CONNECT

AND ISOLATE

DIAGRAM No.10

(Unlocking = 1" - Locking = 40”)

CONTROL UNIT

RED/BROWN

YELLOW/BROWN

DO NOT CONNECT

AND ISOLATE

+30

RED/BLUE

5 AMP FUSES

YELLOW/BLUE

WINDOWS

UNIT

1N4007

LOCKING COMMAND

ELECTRIC

LOCKING CONTROL

DIODE

YELLOW/GREY

ORIGINAL

ACTUATOR

CENTRAL DOOR

DOORS

CENTRAL DOOR

RED/GREY

CONTROL UNIT

UNLOCKING COMMAND

LOCKING
COMMAND

SAFETY KEY

LOCK

DIAGRAM No.8

(Unlocking = 1" - Locking = 40”)

GT ALARM

RED/BROWN

YELLOW/BROWN

DO NOT CONNECT

AND ISOLATE

+30

RED/BLUE

AMP FUSES

YELLOW/BLUE

WINDOWS

UNIT

LOCKING COMMAND

ELECTRIC

LOCKING CONTROL

DIODE

YELLOW/GREY

ORIGINAL

ACTUATOR

CENTRAL DOOR

DOORS

CENTRAL DOOR

RED/GREY

CONTROL UNIT

UNLOCKING COMMAND

LOCKING
COMMAND

SAFETY KEY

LOCK

1N4007

+30

YELLOW/GREY

RED/GREY

YELLOW/BROWN

RED/BROWN

DIAGRAM No.5

(Unlocking = 1" - Locking = 1")

GT ALARM

GT 71

RED/BLUE

YELLOW/BLUE

LIGHT BLUE

ACTUATOR

RED

5 AMP FUSE

7.0 - SET FUNCTIONS

The system is equipped with a “SET FUNCTIONS” which allows to program and customize
the alarm following to the user needs.

To access to the SET FUNCTIONS:

1 - The alarm must be disarmed.
2 - Switch the vehicle ignition key on, place the GT888 handsets contacts to the receptacle
and check that 5 quick beeps are emitted and the RED LED will switch on constant. The
alarm is in SET FUNCTIONS mode. Switch the ignition key off.
3 - After 5 seconds starting from the function No.1 a sequence of LED beeps corresponding
to the function are emitted, the LED flashes can be GREEN or RED to indicate the function
state. The sequential cycle of the LED flashes (from the function No.1 to No.7) is repeated
twice and after you come out automatically from the SET FUNCTION.
4 - To select a function switch on-off the ignition in conjunction with the relative signal, the
LED switches on constant.
5 - Within 10 seconds change the the function by pressing the ON/OFF handset button.
The change is confirmed by the change of the LED colour and by a beep. After 10 seconds,
starting from the last function selected, the function sequence will start again.

To come out from the SET FUNCTIONS:

Wait untill the end of the signals and place the GT888 handsets contacts to the receptacle
(not during the Function No. 1 - HANDSETS SELF-CODING). The end of the sequence is
confirmed by the Led switching off and by 5 beeps. In the “FUNCTIONS TABLE” are the
functions which can be selected.

SET FUNCTIONS emergency disarming procedure.

If the GT888handset-electronic key lost it is possible to enter the SET FUNCTIONS:

A -

With the alarm disarmed disconnect the power supply and wait 3 minutes.

B -

Short-circuit the RECEPTACLE/LED contacts.

C -

Connect the power supply again.

D -

Switch on and off the vehicle ignition key four times and check that 5 quick beeps are

emitted and the LED is constant RED to confirm you have entered the SET FUNCTIONS.

E -

Remove the short-circuit between the RECEPTACLE/LED contacts before carrying out

the selection of a function that is required.

SET FUNCTIONS TABLE

FUNCTION STATE

No.

DESCRIPTION

ENABLED

DISABLED

HANDSETS SELF-CODING

RED

RAPID TEST

RED

COMFORT CLOSINGS

GREEN

1” unlock - 1” lock

RED

1” unlock - 40” lock

ACOUSTIC SIGNAL WHEN ARMING/DISARMING

GREEN

RED

BLINKER COMMAND

GREEN

RED

DOORS PIN SWITCH POLLING MANAGEMENT

GREEN

RED

POSITIVE DOORS PIN SWITCH MANAGEMENT

GREEN

RED

FUNCTION STATE

N   = N   = Function No.
N   = LED flashes No.
N   = Beep

No.

SET UP
PREDEFINED

LEGEND:

- Function No. 1: HANDSETS SELF-CODING .

WARNING:

- When you have entered the function of the first handset which is self-coded it deletes
all the other handsets memorised.
- If you want to add one or additional handsets you have to self-code all of them.
- If you try to self-code an handset

twice consecutively or the maximum handsets

number has been reached the system emits 3 beeps to indicate there is a problem.

With the function No.1 it is possible to self-code new handsets to the control unit up to a
max of 8.
1 - Select the function and press the “ON/OFF” handset button to be self-coded.
2 - The system will indicate the correct handset self-coding with a flash of the GREEN
LED and a beep.

- Function No. 2: RAPID TEST.

With this function it is possible to check the correct installation carrying out a test of all the
alarm connections.

Additional modules entry test:

triggering the sensor (ultrasonic microwaves, inclination

etc.) the system generates 1 beep and No.1 GREEN flash of the del LED on the receptacle.

DOORS pin switch test:

opening one or more doors the system generates 4 beeps

and 4 GREEN flashes of the LED on the receptacle.

BOOT/BONNET switch test:

opening the boot and bonnet the system generates 5 beeps

and 5 GREEN flashes of the LED on the receptacle.

Starting attempt test:

switching the ignition key on the system generates 6 beeps and

6 GREEN flashes of the LED on the receptacle.

Wires cut test:

taking out the power supply to the alarm the system generates 7 beeps

and 7 GREEN flashes of the LED on the receptacle.

There are two ways to come out from the RAPID TEST:

1 - Automatically waiting 2 minutes without triggering any alarm line.
2 - Place the electronic key incorporated in the handset to the RECEPTACLE/LED or press
the “ON/OFF” handset button.

- Function No. 3: COMFORT CLOSING.

If enbled it allows the windows to automaticaly close (only for the vehicles equipped with
this function) supplying a closing command with a duration of 40 seconds after 5 seconds
from the doors closing and the alarm is set.
1 - Select the function and ENABLE/DISABLE pressing the “ON/OFF” handset button.

- Function No. 4: ACOUSTIC SIGNAL WHEN ARMING/DISARMING.

It is possible to program the acoustic signal (beep) to indicate the alarm arming and
disarming on or off.
1 - Select the function and ENABLE/DISABLE pressing the “ON/OFF” handset button.

- Function No. 5: INDICATOR COMMAND.

If the function is

ENABLED

with the only ORANGE wire it is possible to command the

indicators by the emergency indicators original switch (only on the vehicles equipped with
this function).
1 - Select the function and ENABLE/DISABLE pressing the “ON/OFF” handset button.

- Function No. 6: DOOR SWITCH PULSING MANAGEMENT.

If this function is ENABLED it allows connection to vehicles with negative impulses (pulsing)
on the original doors contacts.
1 - Select the function and ENABLE/DISABLE pressing the “ON/OFF” handset button.

- Function No. 7: POSITIVE DOOR SWITCH MANAGEMENT.

If this function is ENABLED, it allows connection to the door contacts which supply a
stable positive when the door is opened.

8.0 - USER MANUAL

LED

ON-OFF

GT884N

(Optional)

ON/OFF

LED

PANIC

GT888

DOUBLE

LOCKING

- HANDSET DESCRIPTION.

GT888:

3 button handset with electronic key

incorporated.

GT884N:

1 multifunction button

(Optional)

- “ON/OFF”:button: to arm and disarm the alarm.

- With automatic transmission selectable if required.

- MANUAL ARMING / DISARMING.

ARMING by HANDSET:
Press the “ON/OFF” handset button, the arming is confirmed by an indicator flash,and by
a Beep and the LED will start to flash.
ARMING by ELECTRONIC KEY INCORPORATED IN THE REMOTE:
Place the electronic key incorporated in the GT888 handset on the RECEPTACLE, the
arming is confirmed by an indicator flash, by a beep.The central door locking won’t be
activated and the first alarm cycle will be anticipated by a sequence of beeps and flashes.
DISARMING:
Press the “ON/OFF” handset button or place the electronic key incorporated in the handset
on the RECEPTACLE,disarming is confirmed by two indicator flashes,and by two Beeps
the LED switches off (the system emits 4 flashes and 4 beeps if an alarm conditionhas
been detected).

- ADDITIONAL MODULES AND ULTRASONIC ISOLATION.

In the first 5 seconds after the system is armed press the panic button on the remote

control the indicators flash once more and a tone is emitted the sensors are then excude
for one cycle ony and will be re include next time the alarm is set.

- AUTOMATIC TRANSMISSION ENABLING/DISABLING (ONLY WITH GT884N and ONLY
FOR THE ANTI-HIJACK FUNCTION).

ENABLING: Press and keep the “ON/OFF” handset button for 10 seconds, the Led flashes
slowly. After 10 seconds, the LED flashes quickly then release the button the feature is
now active.
DISABLING: Press and keep the “ON/OFF” handset button depressed for 10 seconds
the LED will now start to flash slowly then release the button the feature is now off.
Quick flash:

automatic transmission enabled.

Slow flash:

automatic transmission disabled.

- DOUBLE LOCKING.

In the first 5 seconds after the system is armed and the doors lock press the lock button
on the handset a second time and the double locking if connected will be set this is
confirmed by a second tone and flash of the indicators.

- COMFORT CLOSING.

If this function is ENABLED, on the vehicles equipped with this function, the window
closing occurs automatically. If window closers are fitted or you wish to isolate the ultrasonic
sensors, it is possible to stop the windows closing by pressing the handset LOCK
BUTTON a second time until the desired position is reached or until the windows are fully
closed.

- ANTI-HIJACK (Available only with GT884N).

This function allows the user to activate the engine imobiliser if they are forced to leave it
. The operation occurs

only by the GT884N handset in “LINK-AUTOMATIC TRANSMISSION”

mode.

1 - With the ignition on the LED illuminates constant RED to indicate that the anti-hijack
procedure is activated. If the LINK signal is missing for more than 30 seconds the system
enters the anti-hijack phase.
2 -The LED illuminates constant GREEN.
3 - After 15 seconds the indicators start flashing.
4 - After other 15 seconds the system emits an alarm cycle with a duration of 30 seconds.
If the ignition stays on another alarm cycle is generated.
5 - When the ignition is off the engine immobilisation is activated and it sops the vehicle
starting. An alarm cycle will be generated by attempting to start the vehicle.
6 - To come out from the anti-hijack state, from any phase, it is necessary to have the
handset in LINK- AUTOMATIC TRANSMISSION and approach the vehicle. The operation
will be confirmed by two flashes of the indicators, two Beeps of the siren and by the LED
switching off.

- PROTECTION

When the system is armed the check status LED switches on constant, after 30 seconds
the LED starts to flash. The

ignition key, boot/bonnet

protection are active

5 seconds

after arming,

while the

door pin switch and the additional input

and

the wires cut (only

for GT915/916)

are only active when the

check status LED flashes.

- PANIC FUNCTION (only with GT888).

- Press the “PANIC” button with the system fully armed(LED FLASHING)the indicators
flash and the siren sounds.
- Press a second time the “PANIC” button to stop the panic.

- BACKUP BATTERY RECHARGE.

The device is equipped with internal battery to provide the siren with power if the battery is
disconnected during the armed condition.For the siren battery to become fully charged
the system has to have been fully connected to the vehicle for 24 hours.

EMERGENCY DISARMING.

In case of emegency (i.e. handset battery discharged) it is possible to deactivate the
system by inserting the contacts on the remote control supplied into the RECEPTACLE
that has been fitted.

- IN CASE OF ALALRM.

- Press the “ON/OFF” button to disarm the system.
- Press the “PANIC” button to stop the alarm cycle without disarming (only with GT888).

- ALARMS CHECK CONTROL AND ANOMALIES.
LAST ALARM CAUSE:

If during the armed state an alarm has been detected (4 indicators flashes and 4 beeps
to the disarming) or there is anomaly it is possible to check the cause.
When the alarm is disarmed switch the ignition key on and check the LED flash as
indicated in the ALARMS SIGNAL TABLE and ANOMALIES SIGNALS TABLE.

ANOMALIES SIGNALLING:

- Vehicle low battery signalling:

when disarming with the handset, if the vehicle battery is

at 11,6V doesn’t activate the indicators and after the normal acoustic signalling emits 5
anomaly beeps.

- Door open signalling when arming:

the system emits a long beep and a long indicators

flash.

Handset low battery signalling:

when the system is disarmed switch on the vehicle

ignition key athe system emits some flashes of colour GREEN and RED without pauses
(See TABLE ANOMALIES SIGNALLING).

ALARMS SIGNALLINGS TABLE

Check LED

Flashes No.

Input which has

generated the alarm

RED

PAUSE

ADDITIONAL MODULES

INPUT

RED

PAUSE

DOORS PIN SWITCHES

RED

PAUSE

BOOT/BONNET PIN

SWITCH

RED

PAUSE

VEHICLE IGNITION KEY

RED

PAUSE

WIRES CUT

(only for GT915/916)

ANOMALIES SIGNALLINGS TABLE

Check LED

Flashes No.

Input which has

triggered the alarm

RED / GREEN

HANDSETS BATTERY

COLOUR

N = Flashes No.
COLOUR = Flashes colour

LEGEND:

Flashes without pause

RED/GREEN

- The signals sequence of occurred alarms and anomalies detected is repeated at
each vehicle ignition key switching on.
- The alarms system memory is deleted to the following the alarm system arming.
- When the anomaly is solved, the memory is automatically deleted.

WARNING:

- HOW TO REPLACE THE HANDSET BATTERY.

WARNING!

- The battery negative terminal has to be
pointed upwards (with components) and the
positive downwards (handset bottom).

Replace with a Lithium battery
Mod. CR2032 (3V) for GT888
Mod. CR2450 (3V) forGT884N
Take out and insert the battery
from this circuit side.

- With care lever the front case for the
printed circuit

LED

Tasto

ON/OFF

WARNING:

the batteries selling off has to always

occur in appropriate way and it has to be in
compliance with the local rules in force.

9.0 - MAINTENANCE AND WARNINGS

MOTOR VEHICLEWASHING.

It is necessary to pay particular attention to any source of water spray. It is advisable, during
this operation to protect it with a covering (i.e. cellophane).

- FUNCTIONS CHECK.

To have an always efficient system it is advisable
to carry a periodic check of all the functions.

- HANDSET.

Do not expose the handset to excessive heat
sources, water and shocks. For the battery
replacement refer the picture below.
The battery selling off has to always occur in
appropriate way and it has to be in compliance
with the local rules in force.

- PRACTICAL ADVICES.

The remote control handset operates through
radio waves. Avoid to place it in zones which
could compromise the operation (hip pockets,
bags, etc.). Do not put together the remote
control handset with the automatic transmission enabled to the bunch of keys.

10.0 - COMPLIANCE DECLARATION

Getronic S.r.l. Via Calcinate, 12 Gavirate, Italy hereby declares that

GT915

916

917/918

are

in compliance with

the following European Directive:

R&TTE 1999/5/CE (including the directives: 95/54CE)

All Getronic products are compatible with the vehicle’s original electronic systems.
The

GT888/884N

handsets are in compliance with sthe following European Directives:

EMCC DR. RASEC “Notified Body 0678”

R&TTE 1999/5/CE (including the directives: EN 300 220 - EN 60950)

The President
Danilo Restelli

Varese, 7 April 2005

- Power supply:

9-16V.

- Working temperature:

-40° / +85°.

- Max apllicable voltage:

36V/1minute

- Current draw - disarmed system:

<12 mA.

- Current draw - armed system:

<16 mA.

- Current in alarm state.

< 600 mA

- Current in “SLEEP MODE”:

<20µA.

- Max current for engine immobilisation:

7A.

- Max current for central door locking:

5A.

- Max current Blinker output:

5A.

- Max current Led output:

25 mA

- Max current positive output:

80 mA.

- Self-power supply (only for GT915/916):

Battery 7,2V Ni-Mh - 120mA

11.0 - TECHNICAL DATA

- This Certificate should be kept in a safe place and produced for verification should
technical assistance be required. Inability to produce this Certificate may affect your
warranty rights. Warranty period bengins from date of purchase and is valid for 12 months
(24 months for U.K.).
Should technical assistance be required during the warranty period, you should take
your vehicle and this Certificate to either the original installer or the nearest GT Auto
Alarm Service Centre for inspection. Should any part of the security system be found to
be defective, and providing all component parts of the system are of GT Auto Alarm
manufacture, the defective part will be replaced or repaired free of charge. Warranty
replacement/repair does not include the following items:

) damage caused in transit/carriage;

)damage caused by incorrect or poor installation; problems which may be caused by

anomalies in the vehicle’s electrical system or originating from the environment in which
the system is operated.

damage caused by carelessness, negligence, misuse or repair by unauthorised

personnel.
Units returned to our organisation under the terms of the warranty will be replaced or
repaired within a reasonable time period according to our Company requirements.
Any repair/refurbishment received within the warranty period does not extend or renew
the warranty itself.
Nobody is authorized to modify or replace anything in verbal or written format which
alters the conditions of this warranty.
The manufacturer reserves the right to modify or improve the specification.
The alarm only defects burglary attempts. Our company cannot accept liability for any
consequential damage or loss to persons or property as a result of purchase of a GT
Auto Alarm system.
Any correspondence for litigation purposes shall be received at our headquarters in
Gavirate (Varese) - Italy.

12.0 - WARRANTY CONDITIONS

CUT AND KEEP

ManInstGT916-UKRev01.p65

Installation Certificate

We certify that the alarm system installation has been carried out
following these fitting and that the technical data has been handed

over.

Warranty coupon

Alarm model

ALARM MODEL:

INSTALLATION DATE:

INSTALLED ACCESSORIES:

POSSIBLE INSTALLED

ACCESSORIES:

STAMP AND INSTALLER
SIGNATURE:

INSTALLATION DATE:

MAKE AND CAR MODEL:

STAMP AND INSTALLER
SIGNATURE

Ask a Question ?

PDF User Manual

GT918\ GT916\ GT917

Full Text Searchable PDF User Manual