PDF User Manual

Olympic Installations Tools  

126 Quality Drive 

Mocksville, NC 27028 

Phone:  336-751-1555 

Fax:  336-751-0303 

INSTRUCTIONS FOR THE USE AND MAINTENANCE FOR THE RV74G 

INSTALLATION TOOL 

(Formerly the RV73G tool) 

Description: 

The Olympic Model RV74G is an electric installation tool recommended for the installation of 
Olympic fasteners. It operates on 120VAC 60Hz. Pulling heads corresponding in size with the 
diameter of fasteners to be installed must be attached to the RV74G tool.  Heavy-duty snap-on 
series pulling heads are available and capable of installing 1/8” to 9/32” Bulbtite Olympic 
Fasteners.   Other pulling heads may be used in combination with the correct adapter. 
 

Operation: 

 
Attach the snap-on series pulling head to the installation tool in the following manner: actuate 
the installation tool until the draw bolt is in the extreme forward position.  Thread the pulling 
head draw bolt fully to the installation tool draw bolt (Assy. 8023).  Lift the spring band (3143).  
Slide the pulling head housing into the tool nose sleeve. Release the spring band (3143). The tool 
is now ready for operation. 
 
Fasteners are installed with the Olympic RV74G installation tool by first placing the fasteners 
into the holes of a prepared panel or sheet.  Then  apply the pulling head nose onto the fastener 
stem sliding the pulling head to the flange of the fastener.  Then activate the tool by squeezing 
the motor trigger. 
 
Depending upon the application, the fastener may first be inserted by hand into the pulling head 
nose where it may be held in place by the head mechanism.  Then the shank portion of the 
fastener can be inserted into the prepared holes prior to activating the installation tool. 
 
The pulling action is a continuously reciprocating one.  The pulling head jaws will grip the 
fastener stem repeatedly as the installation tool moves the draw bolt back and forth.  In the 
instance of long fasteners, the bolt may reciprocate several times before the fastener stem is 
broken. 
 

Maintenance: 
 

The RV74G installation tool has been engineered to provide trouble free operation under normal 
usage conditions.  No lubrication is necessary unless the tool has been disassembled.  Upon 
reassembly, pack the RV74G tool with 

Keystone Zeniplex 2 grease

. 

 
The pulling head will require periodic cleaning.  A small rifle brush passed through the jaws will 
maintain the efficiency of the tool.  Occasionally disassemble the entire pulling head and clean 
thoroughly, paying special attention the jaws. Upon reassembly, lubricate the inside conical 
surface of the collet sparingly with a light chassis lubricant. Refer to the applicable pulling head 
drawings. 
 

Caution: 

 
DO NOT operate the tool on a current with voltage outside the specified limits.  To do so may 
seriously damage the tool.  
 

Extension Cord Selection: 

 
If an extension cord is used, make sure the conductor size is large enough to prevent excessive 
voltage drop that will cause loss of power and possible motor damage. Also if used outdoors, use 
only extension cords approved for outdoor use. 
 

Amperage Rating 

25 feet 

50 feet 

100 feet 

More Than 

Not More Than 

AWG 

0 

6 

18 

16 

16 

6 

10 

18 

16 

14 

10 

12 

16 

16 

14 

12 

16 

14 

12 

Not Recommended 

WARNING: 
 

When using electrical tools, basic safety precautions should always be followed to reduce the 
risk of fire, electric shock and personal injury. 
 
Keep work areas clean to prevent injuries. 
 
DO NOT expose the tool to rain. DO NOT use in damp or wet locations.  If water or fluids enter 
the motor, discontinue use and send the tool in for repair. Keep work areas well lighted.  Avoid 
chemical or corrosive environments.  DO NOT use tool in presence of flammable liquids and 
gases. 
 
Prevent body contact with grounded surfaces. 
 
When tool is not in use, it should be stored in a dry place. 
 
DO NOT wear loose clothing or jewelry. 
 

Never carry the tool by the cord or pull to disconnect from receptacle.  Keep cord away from 
heat, oil, and sharp edges. Have damaged or worn power cords replaced immediately. 
 
Keep proper footing and balance at all times. 
 
Stay Alert! Watch what you are doing. DO NOT operate when you are tired or while under the 
influence of medication, alcohol, or drugs. 
 

Maintain Tools with Care

: 

 
Follow the instructions for lubrication and changing accessories.  Inspect the tool’s cord 
periodically.  Inspect extension cords and replace if damaged. Have all worn, broken or lost parts 
replaced immediately. Keep handles dry, clean and free from oil and grease. 
 
There are certain applications for which this tool is designed.  It is strongly recommended that 
this tool NOT be modified and/or used for any application other than which it was designed.  If 
you have any questions relative to its application, do not use the tool until you have contacted 
GESIPA Fasteners USA, Inc and we have advised you. 
 

Technical Assistance and Tool Repair: 

GESIPA Fasteners USA, Inc. 

126 Quality Drive 

Mocksville NC, 27028 

Phone:  336-751-1555 

Fax:  336-751-0303 

RV74G 

Part Number Listing 

Part Number 

Description 

3022 

NUT 

3111 

THRUST BEARING 

3118 

THRUST RACE 

3128 

RACE SPACE R 

3141 

BOLT 

3143 

SPRING BAND 

3149 

COVER SCREW 

3307 

COVER 

3317 

NEEDLE BEARING (6MM) 

3321 

SPRING WASHER 

4221 

MOTOR 120V ASSEMBLY 

4222 

MOTOR BEARING PLATE 

4226 

WORM GEAR ASSEMBLY 

4227 

HOUSING ASSEMBLY 

8023 

DRAW BOLT ASSEMBLY 

CAP SCREW 

CAP SCREW