Gerni Super 130.2 User Manual - User Manual

Download PDF User Manual

Full Text Searchable PDF User Manual

Super 130.2 S
Super 130.2
Super 140.2
Super 145.2

User Guide

Super 130.2 S
Super 130.2
Super 140.2
Super 145.2

128303529

Why compromise

Printed in China
Copyright © 2010 Gerni

Index

  1  Safety precautions and warnings .............................................3
2  Description ...............................................................................4
  3  Before you start using your pressure washer ...........................5
  4  Operating your pressure washer ..............................................6
  5  Fields of application and working methods ............................10
  6  After using your pressure washer ...........................................12
7  Maintenance

...........................................................................13

8  Trouble shooting .....................................................................14
9  Further information .................................................................15
10  EC Declaration of Conformity .................................................17

1 Safety Precautions and Warnings

Before starting up
your high-pres-
sure washer for
the fi rst time, this
instruction manual

must be read through carefully.
Save the instructions for later
use.

Safety instruc-
tions marked with
this symbol must
be observed to
prevent danger to

persons.

This symbol is used

to mark safety

instructions that

must be observed

to prevent damage to

the machine and its perform-

ance.

This symbol in-
dicates tips and

instructions to simplify work and
to ensure safe operation.



Do not let children or people
who have not been trained
in the use of a high pressure
washer nor read the instruction
manual ope rate the machine.

This appliance is not intended
for use by children or other
persons without assistance or
supervision if their physical,
sensory or mental capabili-
ties prevent them from using it
safely. Children should be su-
pervised to ensure that they do
not play with the appliance.

Before starting up your machine
please check it carefully for any
defects. If you fi nd any, do not
start up your machine and con-
tact your Gerni distributor.

Especially check:



The insulation of the electric

cable should be faultless
and without any cracks. If the
electric cable is damaged, an
authorized Gerni distributor
should replace it.

WARNING!



High pressure jets can be

dangerous. Never direct the
water jet at persons, pets,
live electrical equipment or
the machine itself.



Never try to clean clothes or

footwear on yourself or other
persons.



Hold the spray lance fi rmly

with both hands. The spray
lance is affected by a thrust
of up to 16.4 N during ope-

ration.



The operator and anyone in

the immediate vicinity of the
site of cleaning should take
action to protect themselves
from being struck by debris
dislodged during operation.
Wear goggles and protective
clothes during operation.



This appliance has been de-

signed for use with cleaning
agents supplied or recom-
mended by the manufacturer.
The use of other cleaning
agents or chemicals may
adversely affect the safety of
the appliance.



Disconnect from electrical

power supply before carrying
out user maintenance.



To ensure the appliance

Symbols used to mark
instructions

safety only use original spare
parts from the manufacturer
or approved by the manufac-
turer.



High pressure hoses, fi ttings

and couplings are important
for the safety of the appli-
ance. Only use hoses, fi ttings
and couplings recommended
by the manufacturer.



Do not use the appliance

if a supply cord or impor-
tant parts of appliance are
damaged, e.g. safety device ,
high pressure hose and trig-
ger gun.



The appliance is intended for

cleaning outdoors.



Appropriate ear protection

must be used.



Never use the machine in

an environment where there
could be a danger of explo-
sion. If any doubt arises,
please contact the local
authorities.



It is not allowed to clean

asbestos- containing surfaces
with high pressure.



This high pressure washer
must not be used at tempera-
tures below 0°C.





Never let any persons stand
under the product when
stored on the wall.

WARNING!

Inadequate extension cables
can be dangerous. Cables on
reels should always be com-
pletely unwound to prevent the
cable from overheating.

If an extension cable is used,
the plug and the socket must be
waterproof and comply with the
below-mentioned requirements
for length and cable dimen-
sions.

1.0 mm²

max.

12.5 m

1.5 mm²

max.

20 m

2.5 mm²

max.

30 m



Cable connections should be

kept dry and off the ground.



If the electric cable is

damaged, it must be re-
placed by the manufacturer
or his service agent or simi-
larly qualifi ed person in order
to avoid a hazard.

Mains power connection

The following should be ob-
served when connecting the
high pressure washer to the
electric installation:



The electric installation shall

be made by a certifi ed elec-
trician and comply with IEC
364.



It is recommended that the

electric supply to this appli-
ance should include either a
residual current device that
will interrupt the supply if the
leakage current to earth ex-
ceeds 30 mA for 30 ms.

Water connection

Connection to the public mains
according to regulations.

Inlet hose can be connected
to the water mains with a max.
inlet pressure of 10 bar.

IMPORTANT! Only use wa-
ter without any impurities.

there is a risk of silt, sand or
sediment in the inlet water (i.e.
from your own well), an addi-
tional fi lter should be mounted.

Repair and maintenance
WARNING!

Always remove the

electric plug from the socket be-
fore carrying out maintenance
work on the machine.

Safety devices

Locking device on spray gun
(7a)

(see illustration at the end

of this manual)

The spray gun features a lock-
ing device. When the button is
activated, the spray gun cannot
be ope rated.

Thermal sensor:

A thermal sensor protects the
motor against overloading. The
machine will restart after a few
minutes when the thermal sen-
sor has cooled.

Pressure safety device

An integrated hydraulic safety
valve protects the system from
excessive pressure.

2 Description

This high-pressure washer has
been developed for domestic
use for cleaning:

- Car, motorbike, boat,

caravan, trailer, patio/

drive/fl ag stones, wood-

work, brickwork, barbe-

cue, garden furniture,

lawn mower

Section 5 describes the use of
the high-pressure washer for

vaious cleaning jobs.

Only use the high-pressure
washer for purposes described
in this manual.

The safety precautions must be
observed to prevent damage
to the machine, the surface to
be cleaned or severe personal
injuries.

2.2 Operation elements

and model survey

See illustration at the end of
this manual.

1 Start/stop switch
2 Water inlet (with fi lter)
3 High pressure connection

(only models without hose
reel)

  4  High pressure hose
5 Electric cable
  6  Click & Clean spray lance
  7  Spray gun with lock
  8  Click & Clean Tornado

nozzle

9 Click & Clean Powerspeed

nozzle

10  Click & Clean foam sprayer
11  Nozzle cleaning tool
12  Trolley handle (tele-scopic

handle), except 130.2 S

13 Hose reel (not standard)

14 Hose hook
15 Model tag
16 Quick coupling
17 Button for telescopic han-

dle, except 130.2 S

18 Turnable cable hook

Specifi cations:

See model tag

(15) of machine.

Sound pressure level measured
in accordance with ISO 3744
EEC directive 2000/14/EEC: L

= 69,9 dB(A), L

= 84 dB(A).

Hand/arm vibrations measured
according to ISO 5349 is < 2.5
m/s

We reserve the right to alter the
specifi cations.

2.1 Application

3 Before you start using your
pressure

washer

3.1 Mounting of

trolley handle and hose
hook

3.1.1 Super 130.2, 140.2,

140.2

Plus

1. Push down the trolley handle

(12) over the two metal tubes.
Make sure that the handle is
mounted as illustrated. Mount
screws with nuts (make sure
that the screws go through
handle as well as tube).

2. Mount the hose hook (14)

on the machine (2 screws).

Note:

the hose hook can be

mounted on the front as well
as on the back. Front position

3.3 Mounting of quick

coupling

1. Screw the quick coupling (16)

tight on to the water inlet (2).

Note:

The inlet fi lter must al-

ways be fi tted in the water inlet
pipe to fi lter out sand, lime stone
and other impurities as these
will damage the pump valves.

Caution:

Failure to

fi t the fi lter will in-

validate the guar-

antee.



3.1.2

Super 130.2 S

1. Mount the trolley handle (12)

on the machine. Secure the
handle by tightening the 4
screws.

2. Mount the hose hook (14)

on the machine (2 screws).

Note:

the hose hook can be

mounted on the front as well
as on the back. Front position
is to be used if the product is
used together with a special
wall hook for wall storage
(not standard).

3.2 Mounting of hose reel

handle (models with
hose reel)

1. Click the hose reel handle

on to the trolley handle (no
screws).

is to be used if the product is
used together with a special
wall hook for wall storage
(not standard 130.2 models).

4 Operating your pressure washer

4.1 Connection of high

pressure hose (models
without hose reel)

1. Mount the high pressure

hose on the outlet (3).

3.4 Mounting of high
pressure

hose

Attach the high pressure hose
(4) to the spray gun (7).

Detach the high pressure hose
by pressing the button (A).

4.2 Mounting of spray

lance and Click & Clean
nozzles



1. Push the spray lance (6) into

the spray gun (7) and twist
it until the bayonet coupling
locks into position..

Note:

The

spray lance (6)

has a built-in low

pressure nozzle

that can be used for

fl ushing away dirt.

2. Attach the nozzle.

Warning:

When

attaching the Click
& Clean nozzles,
the button on

the side of the spray lance
should return to the locked
position. Ensure that there is
an audible "click".

Note:

The Tor-

nado

PR nozzle

and the foam

sprayer feature a swivel lock,
which must be positioned in the
hole in the Click & Clean spray
lance.

4.3 Water connection

An ordinary 1/2" garden hose of

min. 10 m

and

max. 25 m

will

be suitable.

NOTE

: Connection to the public

mains according to regulations.

IMPORTANT! Only use wa-
ter without any impurities.

there is a risk of silt, sand or
sediment in the inlet water (i.e.
from your own well), an addi-
tional fi lter should be mounted.

1. Let the water run through the

water hose before connecting
it to the machine to prevent
sand and dirt from penetrat-
ing the machine.

Note:

Check

that the fi lter is
fi tted in the water

inlet pipe and that it is clean
and free from debris.

2. Connect the water hose to

the water supply by means
of the quick connector (inlet
water, max. pressure: 10 bar,
max. temperature: 50°C).

3. Turn on the water.

4.4 Telescopic handle

(Super 130.2, 140.2,

140.2

Plus)

The machine (Super 130.2,
140.2, 140.2 Plus) features a
tele scopic handle. To raise or
lower the handle, press the
knob and move the handle up-
wards or downwards. When a
click is heard, the handle is in
right position.

Press the button to detach the
Click & Clean nozzle.

4.5 Start and stop of the ma-

chine (when connected
to a water supply)

The spray lance is affected
by a thrust during opera-
tion - therefore always hold it
fi rmly with both hands.

IMPOR-

TANT

Point the nozzle at the

ground.

1. Check that the machine is in

upright position.

NOTE:

Do not place the ma-

chine in tall grass!

2. Release the trigger lock.
3. Activate the trigger of the

spray gun and let the water
run until all air has escaped
from the water hose.

4. Turn the start/stop switch (1)

to position "

5. Activate the trigger of the

spray gun.

Always adjust the distance and
thus the pressure of the nozzle
to the surface, which is to be
cleaned.

Do not cover the machine
during operation.

Note:

If the ma-

chine is left or
not used for 5

minutes, it must be switched off
on the start/stop switch "

" (1):

1. Turn the start/stop switch to

position "

2. Disconnect the electrical plug

from the socket.

3. Shut off the water supply and

activate the trigger to relieve
the machine of pressure.

4. Lock the spray gun.

When releasing the trigger of
the spray gun, the machine
automatically stops. The ma-
chine will start again when you
re-activate the spray gun.

the water and then connect
the hose to the machine with
the quick coupling and fi nally
uncrimp the water inlet hose.

2. Turn the start/stop switch to

position "

3. Activate the trigger of the

spray gun with lance and
nozzle removed and let the
water run, until the air has
escaped from the water hose
and the pump.

4. Mount spray lance and

nozzle.

The washer can draw water
from a rain water tank or bucket
as an example. The hose for the
water supply must not be too
long, approx. 5 m.

Make sure that the water tank is
not placed on a lower level than
the machine.

Use an external fi lter if the wa-
ter contains impurities.

1. Make sure that the water

hose is fi lled completely with
water before connecting to
the machine. Place the entire
hose in a tank or bucket. To
avoid water spillage, crimp
the water inlet hose down in

4.6 Start the machine (when

connected to open con-
tainers (suction mode))

4.7 Pressure regulation on

the TORNADO

PR-nozzle

The pressure can be regulated
on the TORNADO

PR nozzle.

4.8 Stationary use

If mounting a special wall hook
(not standard), the pressure
washer can be used as a sta-
tionary solution meaning that it
can be operated while hanging
on the wall.

Only mount the wall hook on a
sturdy wall. Adjust the length
of the screws and size of rawl-
plugs to the type of wall.

On the wall hook garden/rim
brush (a) foam sprayer (b),
Click & Clean brush (c) and
Click & Clean nozzles (d) can
be stored.

Important:

The bearing capa-

city of the wall

hook is max. 30 kg.



Lavtryk

Højtryk

High pressure

Low pressure

5 Fields of application and
working

methods

5.1 General

Effi cient high presure cleaning is achieved by following a few guide-
lines, combined with your own personal experience of specifi c
cleaning tasks. Accessories and detergents, when correctly cho-
sen, can increase the effi ciency of your pressure washer. Here is
some basic information about cleaning.

5.1.1 Detergent and foam

Foam or detergent should be applied onto dry surfaces so that the
chemical product is in direct contact with the dirt. Detergents are
applied from bottom to top, for example on a car bodywork, in order
to avoid "super clean" areas, where the detergent collects in higher
concentration and streams downwards. Let the detergent work for
several minutes before rinsing but never let it dry on the surface be-
ing cleaned.

Note:

It is important that the detergents do not dry up.

Otherwise the surface that has to be cleaned can be da maged.

5.1.2 Mechanical effect

In order to break down tough layers of dirt, additional mechanical
effect may be required. Special wash brushes offer this supplemen-
tary effect that cuts through dirt (especially by car washing).

5.2 Typical fi elds of application

Below you will fi nd a description of a lot of cleaning tasks which can be solved by a pressure washer
from Gerni in association with accessories and detergents.

Task

Accessories ‘Click

& Clean’

Cleaning method

Car

Car nozzle,
auto brush,
underchassis

nozzle,

Foam sprayer,

Neutral car wash

1. Apply neutral car wash with the foam sprayer. Always start

from the bottom and work upwards. Let neutral car wash act
for at least 5 min.

2. Wash the car with the car nozzle, which has been optimized for

quick and gentle cleaning of enamelled surfaces (the jet is wider
and not so sharp). Start at the front of the car and work back-
wards to avoid water from penetrating by the door mouldings.

3. Use the brush for removal of traffi c fi lm which is not removed by the

nozzle. If the car is very dirty, apply neutral car wash again.

4. Attach the undercarriage nozzle and clean undercarriage and

wheel arches.

5. Remove water from the surface of the car with the squeegee

on the car brush.

Make sure

that all grains of sand etc. have

been removed before using the squeegee. Wipe with a wash
leather where the squeegee cannot reach.

Rims, alu-

minium

Rim brush,
auto nozzle,
atomizer,
alloy cleaning

agent

Apply alloy cleaning agent with an automizer. Let it act for approx.

5 min. and wash with the rim brush. For steel rims, use neutral
car wash. Use the foam sprayer and wash with rim brush.

Be careful!

The high pressure jet may damage the tyres.

Flag-

stones,

concrete

fl oors and
other hard
surfaces

Powerspeed

nozzle,
neutral detergent,
Patio Cleaner

Wash towards outlets or the like. On surfaces with moss or al-

gae you may start by applying Neutral detergent with the foam
sprayer. Wash before the soap dries. Another more effective and
quicker method is to use the Patio Cleaner. Thus you will also
avoid splashes.

Garden

furniture,
wood

Wood Cleaner
Garden brush

Apply Wood Cleaner and wash before the soap dries.

NOTE:

Use the garden brush to clean off the dirt.

Brickwork,
Wood

work

Powerspeed

nozzle,
neutral detergent,
Patio Cleaner

Same method as for fl agstones, but

be careful -

bad joints and

wood may be damaged by high pressure. You may choose only
to use the Tornado

nozzle. Adjust the distance (pressure) to

the quality of the joints and the wood. Patio Cleaner can also be
used on vertical surfaces.

Gutter

Underchassis spray

lance

Wash the gutter with the nozzle. Always wash towards

downpipes.

Beware

not to spray under the roofi ng.

Cleaning

of drain
pipes, out-
lets, down
pipes etc.

Tube cleaner

Push the tube cleaner approx. ½ m (to mark) into a tube or drain

and activate the trigger of the spray handle. The nozzle opening
turning backwards will pull the cleaner through the tube. The
nozzle will break down the „plug“ and fl ush the dirt backwards.

Rust, paint

Water/sandblasting

equipment

Mount the water/sand blasting equipment and rust and paint

is effi ciently and quickly removed. Beware not to damage the
surface to be sandblasted.

Green-

house

Tornado

PR nozzle

brush, neutral de-

tergent

Wash with high pressure and maybe a brush. You may use neu-

tral detergent to remove moss and algae.

Garden

tools,
lawn
mower

Tornado

nozzle, Power-
speed

nozzle,

multiangle adaptor,
degreaser

Rinse the worst dirt off with the nozzle. Apply degreaser with

the foam sprayer and let it act for approx. 5 min. Wash with the
nozzle. You may use the multiangle adaptor for hard to get at
areas to avoid splashing.



6 After using your pressure washer

6.2 Winding up of electric

cable and high pressure
hose

up carefully.

1. Wind up the electric cable on

the appropriate hooks. A built
in clip secure the cable (1).

The lower hook can be

turned to release the electric
cable.

2. The high pressure washer

comes in two models: A) with
hook for storage of high pres-
sure hose (14) - B) with a
hose reel (13).

6.1 Storing the washer

The machine should be sto-
red in a frost-free room!

Pump, hose and accessories
should always be emptied of
water prior to storing as follows:

1. Stop the machine (turn the

start/stop switch (1) to posi-
tion “

” and detach water

hose and accessory.

2. Restart the machine and

activate the trigger. Let the
machine run until no more
water runs through the spray
gun.

3. Stop the machine, unplug

and wind up hose and cable.

4. Place spray handle, nozzles

and other accessories in the
holders of the machine.

Should the machine by mistake
be frozen, it will be necessary
to check it for damage.

NEVER START-UP A FROZEN
MACHINE

Frost damages are not
covered by the guarantee!

To avoid accidents, the electric
cable and the high pressure
hose should always be wound

a + f

6.3 Storage of accessories

The standard accessories
(spray gun (f), spray lance (a),
nozzles (b) foam sprayer (c))
can be stored on the pressure
washer.

The nozzle cleaning tool (d)
and a Click & Clean brush
(e) can also be stored on the
product.

WARNING!

Always disconnect

the electrical plug from the
socket prior to maintenance or
cleaning.
To ensure a long and problem
free working life, please take
the following advice:



Wash off water hose, high

pressure hose, spray lance
and accessories before
mounting.



Clean the connectors of dust

and sand. Make sure that
no sand or dirt is blocking
the movement of the button
on the Click & Clean spray
lance.



Rinse the detergent spraying

attachment after use.



Clean the nozzles.

Any repair should always be
made in an authorized work-
shop with original spare parts.

7 Maintenance

7.1 Cleaning of water
inlet

fi lter

Clean the water inlet fi lter regu-
larly once a month or more fre-
quently according to use. Care-
fully loosen the fi lter with a pair
of pliers and clean it. Check that
it is intact before re-mounting it.

The inlet fi lter must always be
fi tted inside the water inlet pipe
to fi lter out sand, limestone and
other impurities, as they will
damage the pump valves.

CAUTION:

Failure to fi t the fi lter

will invalidate the guarantee.

7.2 Cleaning of nozzle

A clogging up in the nozzle
causes a pump pressure which
is too high. This is why cleaning
is required immediately.

1. Stop the machine and dis-

connect the nozzle.

2. Clean the nozzle.

IMPOR-

TANT:

The cleaning tool (11)

should only be used when
the nozzle is detached!

3. Flush the nozzle backwards

with water.

7.3 Cleaning of machine

vents

The machine should be kept
clean so as to let cooling air
pass freely through the ma-
chine vents.

8 Trouble

Shooting

Please ensure that you check the following before contacting the Gerni service organization:

Symptom Cause

Recommended

action

Machine refuses to

Machine not plugged in

Plug in machine.

start

Defective socket

Try another socket.

Fuse has blown

Replace fuse. Switch off other machines.

Defective extension cable

Try without the extension cable.

Fluctuating pressure

Pump sucking air

Check that hoses and connections are air-

tight.

Motor hums

Low voltage or

Activate the trigger of the spray gun.

low

temperature

Machine stops

Fuse has blown

Replace fuse. Switch off other machines.

Incorrect mains voltage

Check that the mains voltage corresponds

to specifi cation on the model tag.

Thermal sensor activated

Leave the washer for 5 minutes to cool

down.

Nozzle partially blocked

Clean the nozzle (see section 7.2)

Fuse blows

Fuse too small

Change to an installation higher than the

amp. consumption of the machine.

You may try without the extension cable.

Machine pulsating

Air in inlet hose/pump

Allow machine to run with open trigger

until regular working pressure resumes.

Inadequate supply of

Check that the water supply corresponds

mains water

to specifi cations required (see model tag)

NB!

Avoid using long, thin hoses (min.

1/2")

Nozzle partially blocked

Clean the nozzle (see section 7.2)

Water fi lter blocked

Clean the fi lter (see section 7.1)

Hose kinked

Straighten out hose.

Machine often starts

Pump/spray gun is

Contact your nearest Gerni Service

and stops by itself

leaking Centre.

Machine starts, but

Pump/hoses or accessory

Wait for pump/hoses or accessory to thaw.

no water comes out

frozen

No water supply

Connect inlet water.

Water fi lter blocked

Clean the fi lter (see section 7.1)

Nozzle blocked

Clean the nozzle (see section 7.2)

In case problems other than the above occur, please phone 1300 733 171 or check our website
www.gerni.com.au for your nearest service agent.

7.4 Greasing of couplings

To ensure easy connection and
that o-rings do not dry up, the
couplings should be greased
regularly.

9 Further

information

9.1 Recycling the washer

Make the old cleaner unusable
immediately.

1. Unplug the cleaner and cut

the electric cable.

Do not discard electrical appli-
ances with household waste.

As specifi ed in European Direc-

tive 2002/96/EC on old electri-
cal and electronic appliances,
used electrical goods must
be collected separately and
recycled ecologically.

Contact your local authorities or
your nearest dealer for further
information.

9.2 Warranty conditions

Gerni guarantees high pres-
sure washers for domestic use
for 2 years. If your high pres-
sure washer or ac ces so ries are
handed in for repair, a copy of
the receipt must be enclosed.
Guarantee repairs are made on
the following con dit ions:



that defects are attributable

to fl aws or defects in materi-
als or workmanship. (wear
and tear as well as misuse
are not covered by the gu a r-
an tee).



that the directions of this

instruction manual have been
thoroughly observed.



that repair has not been car-

ried out or attempted by oth-
er than Gerni-trained service
staff.



that only original accessories

have been applied.



that the product has not been

exposed to abuse such as
knocks, bumps or frost.



that only water without any

impurities has been used.



that the high pressure wash-

er has not been used for
rental nor used com mer cial ly
in any other way.

Repairs under this guarantee
include replacement of defec-
tive parts, exclusive of packing
and postage/carriage. Besides,
we refer to your national law of
sale.

The machine should be for-
warded to one of the service
centres of the Gerni organisa-
tion with description/spe ci fi

ca-

ti on of the fault.

Repairs not covered by the
guarantee conditions will be
invoiced. (I.e. malfunctions due
to

Causes

men ti o ned in sec-

tion

Trouble Shooting

of the

instruction manual).

Please phone 1300 733 171
(Australia) or 09 9682610
(NZ) for service or warranty
assistance only after check-
ing possible causes in the
trouble shooting chart on
page 14.

9.3 Accessories

Only use original accessories.

Click & Clean
Car nozzle

Special nozzle for enameled surfaces. Optimal distance: 30 -
50 cm.

Click & Clean
Undershassis
nozzle

90° angled special nozzle for undercarriage and wheel arches.
Integrated guide shoes.

Click & Clean
Brushes

For cars and other surfaces. Available in more shapes.

Extension hose

7 m extension hose increasing the working range.

Drain & Tube
cleaner

15 m long tube cleaner for the cleaning of tubes and drains.

Water-sand-
blasting equip-
ment

For removal of paint and rust. Sand available from do-it-your-
self shops.

Patio Plus

Equipment for quick cleaning of patio/drive/fl agstones.

EU Declaration of Conformity

Product:

High Pressure Washer

Type:

Gerni Super 130.2 S, Super 130.2,
Super 140.2, Super 140.2 Plus, Super 145.2 Plus

Description:

230 V 1~, 50 Hz - IP X5

The design of the unit corre-
sponds to the following
pertinent regulations:

EC Machine Directive

2006/42/EC

EC Low-voltage Directive

2006/95/EC

EC EMV Directive

2004/108/EC

Applied harmonised
standards:

EN 60335-2-79

Applied national standards and
technical specifi cations:

IEC 60335-2-79

Anton Sørensen
General Manager,
Technical Operations EACP

Nilfi sk-Advance A/S
Industrivej 1
DK-9560 Hadsund

Hadsund, 01.06.2010

10 EU Declaration of Conformity

Super 130.2 S

Super 130.2

Super 140.2 / 140.2 Plus

AUSTRALIA:

Nilfi sk-Advance Pty LTd

48 Egerton St

Silverwater NSW 2128

Phone: 1300 556 710

E-mail: sales@gerni.com.au

NEW ZEALAND:

Accent Tools Ltd

232 Bush Rd

Albany

Auckland 0632

Phone: 09 968 2610

E-mail: sales@accent-tools.co.nz

Ask a Question ?