Full Text Searchable PDF User Manual
Designed in Grand Rapids MI, USA Assembled in China
7.3 Inch Car Rear View Mirror Monitor
with Mirror link
Wide LCD Display Screen
User manual
ECE
R
10
Approval No.: 10R-03 12762
ECE
R
46
Approval No.: 46R-04 0019
FK-073MA
Welcome to use our 7.3 inch car Rear view mirror monitor with mirror link.
●We reserve the final explanation right on this User's Manual.
●Specifications are subject to change without notice. Sorry for any inconvenience
caused!
●Please make a copy of the important data. We assume no responsibility for the
data loss.
●This manual has been carefully checked. Please contact our service center when
any typing mistake is found.
●Please read the operating instruction carefully and use the accessories only
provided by the original factory to avoid any unexpected damage. No warranty
will be executed if you are not following the instruction or connecting with the
incompatible accessories, we assume no responsibility for any loss and damage
caused hereby.
●Any discrepancy between the pictures with real products hereinafter, the real
one prevails.
●The working voltage of this model is 10V to 30V, and it can be installed in the
truck if its voltage is 24V. Please refer to the camera manual for the camera power
supply, since it's not from the car rear view mirror. The 24V camera is advisable if
installed to truck or purchase the power adapter to convert the voltage.
User's Manual
Chapter one: Product Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.3 Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.4 Operating panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Chapter two: Installation and Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1 How to install . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.2 Special bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.3 How to wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Chapter three: Adjustable Guideline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.1 About guide line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.2 What is the regular guide line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.3 How to adjust the guide line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Chapter f
:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
our
11
Menu Setting
4.1 Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.2 Menu setting guidance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Chapter five: Mirror Link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.1 How to connect. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.2 Channel switching. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Chapter one: Product Introduction
1.3 Specification
The packing box contains the following accessories, please confirm:
7.3 inch car Rear view mirror monitor with mirror link
wire harness
User's manual
wire cover
Remote control
For the items listed above, please check with your package box. If any damage,
Please contact with the distributor or the agent as soon as possible.
1.1 Package
●
●
●
●
●
7.3 inch wide LCD display screens
2-way video input
Back up camera display
Automatic brightness adjustment
4.0 mm glass and
21 mm car factory OEM bracket
Adjustable guide line
Mode switch between wide screen and dual screens LCD display separately
1.2 Features
●
●
●
●
φ
●
●
Screen size: 7.3 inch
Display screen: TFT-LCD
Aspect resolution: 1280(H)*390(V)
Working voltage: 12V
Working temperature: -20
℃
~+65
℃
Signal system: PAL/Auto/NSTC
●
●
●
●
●
●
●
1.4 Operating panel
7.3 inch ultra high brightness display screen
1
Turn on/off the display screen
Indicator
1
2
3
4
5
6
7
2
3
4
7
6
5
Front light sensor
Mirror link model switch
When the menu is closed, press it to switch model of Mirror link
, model switched between Miracast Mode (Android) and DLNA
Mode (iOS). Effectiveness only for DOUBLE and MOBLIE model.
Selection of video input channel
Press shortly can realize the transformation about video input
channels, also can realize choosing as DOUBLE, VIDEO1, PHONE,
CAMERA channels. Reversing model can't be selected, only for
CAMERA channel and there isn't reversing guideline. When
reverse wire is connected to 12V, system will switch to BACK UP
CAMERA screen automatically and reverse guideline is available.
We can adjust it by remote control.
Color mode adjustment
Short press it can adjust the color mode of the image. Four
modes are available, that is STANDARD, BRIGHT, BEAUTIFUL,
and SOFT. Please be noted that these modes only are accessible
when it's not in reversing mode.
1
2
3
4
8
9
10
11
12
13
14
15
Horn
Special bracket
8
9
10
11
12
13
14
15
16
17
Red to ACC+
Black to GND
Back up signal
Video input
Camera
Connector
Connector cover
16
8
17
Cable cover
2.1 How to install
Remove the original rear view mirror and remain
the metal base on the windscreen
Original car rear view mirror
Along this direction
to install rear view mirror
Along this direction
to install rear view mirror
Along this direction
to install rear view mirror
contrarotate the fixed
rear view mirror
1
We have many kinds of brackets. one of them must suit for your car, and we are
not going to go through anymore examples, because the space is limited.
If you don’t find the same bracket here as your car, please contact us.
2.2 Special bracket
5
6
Chapter two: Installation and Wiring
Different cars have different brackets. It depends on your vehicle maker and
manufacturer.
There are many methods to remove the original rear view mirror, however, please
don’t force the mirror off the bracket.
The manufacturer will not be responsible for any damage caused to your car by
wrong installation of the mirror.
Remove the original mirror
Install mirror monitor on the base
2.3 How to wire
3M
7
8
power
harness
PUSE
BOX
Black to GND
Red to ACC +12V
Black to GND
Red to ACC +12V
Black to GND
Red to ACC +12V
Back up video
Left video
The advisable installation
position for camera
Back up video
By connecting the green line, the reversing signal is input to the rear view mirror
and reversing video can automatically display on the wide 7.3 inch LCD monitor.
Lef
t v
id
eo
CTR1(Green)
it's advisable to connect the reversing line
UP
Clockwise
Down
Right
left
Move the guide line
Rotate the guide line
anticlockwise
Press the button to choose the L or R adjustable guideline
Remote control
R
L
Wrong
position
Right position
9
10
According to the site of standard reference line, we can put reference objects such
as desks in the back area of car. Compared with the marked reference objects, we
can adjust the sites and angle of two guide lines displayed on the monitor. You will
get the accurate and safety guide lines once they coincide with the reference
objects.
Press
setting
button
is
to
enter
into
“
guide
line
adjustment
”
mode
.
The system is
defaulted to adjust left guide line firstly.
Press the button again will switch to adjust
the right guide line. The
up
,
down
left
and
right
buttons
are
to
adjust
the correspondent location
of
guide
lines
.
The
clockwise rotation
and
contra
rotation buttons
are
to
adjust
the
angle
of
guide
lines
.
It
is
easy
to
operate
and
calibrate
.
After finishing calibration, switch the reverse gear to save
the information.
Caution: keep the remote control 0.5m-1.0m from rearview mirror when you use the remote to
adjust the parking lines.
3.3 How to adjust the guide line
Display
on
the
monitor
Generally, to help drivers estimate the distance from obstacles, there are three
lines for reference -red, yellow and green. Those three lines are displayed on the
monitor when car is reversing. The green line is 3m from the back of car and the
yellow line is 2m. The distant red line is 1m from the backside of car while the
closed red line is 0.4m. Both reference lines on the left and right should leave
0.2m space from the car.
20CM
20CM
3.1 About guide line
Regular guide line is fixed. But installation sites of cameras are different as well
as car size. The fixed guide line is not accurate enough for drivers. There will be a
great difference between regular and fixed guide lines and car's real guide lines,
especially when camera is mounted on the left or right side of car backside. It
may cause accidents.
3.2 What the regular guide line is
Chapter three: Adjustable Guideline
11
12
Chapter Four: Menu Setting
Enter picture menu
Guide line clockwise
Menu parameter decrease
Menu parameter increase
Guide line up
Guide line left
Enter guide line
adjustment
Guide line anti-clockwise
Guide line right
Guide line down
Press to reset all
menu and parameters
4.1 Remote control
The menu only can be set by remote control, and kindly check its definition as below.
4.2 Menu setting guidance
Short press “MENU”to enter “PICTURE”, then you can switch among
“BRIGHTNESS”, “COLOR”, “CONTRAST”, “SCALE”, “START LOGO”, “PRESET”,
or enter out. When it switches to “PRESET”, re-press shortly the MENU, and
you would close the menu. UP and DOWN are to change the figure of each
setting.
4.2.1 BRIGHTNESS ADJUSTMENT
The defaulted setting is 50, ranging from 0 to 100, and only CVBS signal can work.
4.2.2 COLOR ADJUSTMENT
The defaulted setting is 50, ranging from 0 to 100, and only CVBS signal can work.
4.2.3 CONTRAST ADJUSTMENT
The defaulted setting is 50, ranging from 0 to 100, and only CVBS signal can work.
4.2.4 SCALE ADJUSTMENT
It's only for the model with guide lines, and no such setting for those without
such function. ON is defaulted setting, and you can manually set it to OFF.
4.2.6 PRESET ADJUSTMENT
4.2.5 START
LOGO ADJUSTMENT
It's defaulted as OFF, and ON is to preset the menu, then it switches to OFF
automatically.
It's is defaulted as “ON”, you can set it to “OFF” manually.
The reversing mode is the top priority, then all touch panel is ineffective. The
video cannot be switched until the parking mode is ended. But the manual
button is accessible. Short press is to adjust the brightness of the monitor, long
press to turn off the screen.
13
Chapter Five: Mirror Link
This is a special device to project your mobile phone to Rear view mirror
monitor through WiFi connection, and the popular standards like DLNA,
Miracast and Air Play. The driver can set the navigation path on the phone
before entering the car, and then so long as the phone WIFI connected to
rearview mirror, the navigation audio and video can be simultaneously
displayed on the rearview mirror. While driving you can also set navigation
path by a passenger using a mobile phone, the image is simultaneously
displayed on the rearview mirror.
5.1 How to connect
1: First, make sure android phone has wireless projection function ( part of
the phone can not support wireless projection, or part of the phone
wireless display needs to root and could use after changing the system file).
2: Click the “M” button on the TP button, switch wireless mode to Android
mode; open the WIFI on your phone, then search equipment in the phone's
wireless projection function, connect the device according to the wireless
device names displayed on the screen , the step is as below:
“M”button
14
4.2.7 VOLUME ADJUSTMENT
The defaulted setting is 80, ranging from 0 to 100, and only CVBS signal can work.
5.1.1 How to connect with Android phone (Android version have more on
how to use wireless projection function, please consult the phone
instructions)
Please note:
Keep the bluetooth being closed when you use mirror link
function and connect your phone
！
WIFI name
tap here
tap here
15
16
After finishing the connection, then the phone screen projected onto the
rear view mirror, you can press “CH” on TP button to decide DOUBLE MOBLIE
dual mode or single-screen mode.
“M”button
1: First, click the “M” button on TP button, switch the wireless mode to iOS
mode.
5.1.2 How to connect with iPhone
2: Using iPhone search WIFI (WIFI name is displayed on the screen and
shown as below), then enter the default password::12345678. After
finishing WIFI connection, bring up the shortcut menu, click on the AirPlay
function, select the device name, and open the Mirroring
.
tap here
Tap here
Turn on it
Tap here
17
18
5.2 Channel switching
5.2.1 Camera full screen display
5.2.2 VIDEO1 and MOBILE display simultaneously
5.2.3 VIDEO1 full screen display
5.2.4 MOBILE full screen display
After finishing the connection, then the phone screen projected onto the
rear view mirror, you can press “CH” on TP button to decide DOUBLE MOBLIE
dual mode or single-screen mode.
Press the “CH” button on the screen, could switch display among CAMERA
(default and only full screen display), VIDEO1, MOBILE, VIDEO1 full screen
display and MOBILE full screen display.