Full Text Searchable PDF User Manual
ZAGIL
GSM/GPRS MODEM
OPERATION MANUAL
Operation Manual
User Guide
MANUAL
1
G E R M A N E L E C T R O N I X
ZAGIL GSM/GPRS MODEM User Guide
©
German ElectroniX
Erzgiessereistr. 39 b in 80335
Munich / Germany
Tel: +49-179-295-3496
Fax: +49-89-4209504159
Table of Contents
Package Content ....................................................................... 1
Features .................................................................................... 1
Specifications ............................................................................ 2
Installation ................................................................................. 3
Basic Operation ......................................................................... 4
G E R M A N E L E C T R O N I X
1
Package content
1.
ZAGIL GSM MODEM Terminal.
2.
FS socket fixed with Flat cable 20cm.
3.
Female connector for Supply.
4.
Serial Cable.
5.
User manual
Features
Quad-band GSM
Desktop ABS case
Industrial standard design and quality guarantee
Side mounting
RS232 Serial interface
TTL Interface
Status LED Power/GSM/Call
Based on simcom340 module
AT commands
Compatible with Microchip circuits “TTL logic interface”.
G E R M A N E L E C T R O N I X
2
Specifications
Frequency
bands
- Tri-band: EGSM 850, 900, DCS 1800, PCS 1900. The MODEM can search the 4
frequency bands automatically. The frequency bands also can be set by AT COMMAND.
- Compliant to GSM Phase 2/2+
GSM class
Small MS
Transmit
power
- Class 4 (2W) at EGSM900
- Class 1 (1W) at DCS1800 and PCS 1900
GPRS
connectivity
- GPRS multi-slot class 10
（
default
）
- GPRS multi-slot class 8 (option)
- GPRS mobile station class B
DATA
GPRS:
CSD:
- GPRS data downlink transfer: max. 85.6 kbps
- GPRS data uplink transfer: max. 42.8 kbps
- Coding scheme: CS-1, CS-2, CS-3 and CS-4
- supports the protocols PAP (Password Authentication Protocol) usually used for PPP
connections.
- Integrates the TCP/IP protocol.
- Support Packet Switched Broadcast Control Channel (PBCCH)
- CSD transmission rates: 2.4, 4.8, 9.6, 14.4 kbps, non-transparent
- Unstructured Supplementary Services Data (USSD) support
SMS
- MT, MO, CB, Text and PDU mode
- SMS storage: SIM card
- Support transmission of SMS alternatively over CSD or GPRS. User can choose
preferred mode.
FAX
Group 3 Class 1
Phonebook
management
Support phonebook types: SM, FD, LD, RC, ON, MC.
SIM interface
Support SIM card: 1.8V ,3V
External
antenna
Connected via 50 Ohm antenna connector or antenna pad
Serial interface Autobauding supports baud rate from 1200 bps to 115200bps.
TTL interface
"low" when between 0 V and 0.8 V
"high" when between 2.2 V and 5 V
IDC socket 10 pin
Antenna
connector
SMA female, GSM 50
Ω
antenna included
LED indication
Green: power ON Red: GSM status Yellow: Incoming call
Power supply
Single supply voltage 5VDC
Power saving
Typical power consumption in SLEEP mode to 3.5mA ( BS-PA-MFRMS=5 )
Temperature
range
- Normal operation: -20°C to +55°C
- Restricted operation: -30°C to -20°C and +55°C to +80°C
Case type
ABS desktop , wall mounting
Supply
connector
Screw connector 2.5 mm
Dimension
Weight
155mm*85mm*46mm
200g
3
Interfaces
1 Serial port RS232
1 TTL Voltage level Socket “FC10”
Power supply
（
DC 5V
、
500mA
）
Antenna interface
Status lights,
Green light indicate power status
SIM Card Holder
.
FIGURE 1
TTL FC10 socket,
Serial Port, Power supply socket
Installation
a) Open the SIM card holder,
insert in a valid SIM Card
provided by GSM network
operator or Service provider.
b) Install the GSM Modem to
your location and connect the
antenna to the SMA connector.
c) Fix the serial cable to the GSM modem, the supplied
cable will connect the unit to a PC. For other devices you
may need a crossover cable.
d) Connect the GSM Modem power supply interface
with the power adapter’s output jack, and then connect
the adapter to its power supply source.
Make sure that all connections are properly
4
TTL socket description
You supply the modem throw FC10 socket as it shown in figure 4 so no need to
supply it from 2.5 connector
Basic Operation
A. Module connection with
Hyper
Terminal
.
1. Establish or Open
Hyper
Terminal
from
All
Programs
>
Accessories
>
Communications and setting up relevant parameters. Module baud rate is 115200.
(1). Establish connection.
5
(2). Setting up usage port.
(3). Setting up port
parameters
.
6
(4). Setting up
property
in
File
Menu
of
Hyper Terminal
7
8
2. You can input word “
AT
” then press “
Enter
” key, it should be response word “
OK
” means
work
Property.
All commands are executed by pressing
“
Enter
”
key.