GeoVision GV- RK1352 Installation Manual - User Manual

Full Text Searchable PDF User Manual

September 23, 2010

GV- RK1352 Card Reader

The GV-RK1352 is a card reader with keypad, designed to recognize PIN codes,
identification cards or both. Featured with the Wiegand and RS-485 outputs, the unit can be
connected to any standard access control panel. GV-RK1352 comes with a weather sealed
and IP66 compliant housing for outdoor use.

1. Packing List

GV-RK1352 Card Reader x 1

Screw x 2

Screw Anchor x 2

GV-RK1352 Software CD x 1

GV-RK1352 Installation Guide x 1

Front Cover Plate x 2

Front View

2. Electric Wire

Wire Color

Function

Red

DC 7.5 ~ 12 V

Black GND
Yellow Beeper
Orange Green

LED

Light Red

Red LED

Green

Wiegand Data 0

White

Wiegand Data 1

Blue RS-485

Light Blue

RS-485 -

Rear View

September 23, 2010

3. Keypad

When accessing an entry, you can enter the door’s PIN code on the keypad or present the
card and then enter the card’s PIN code on the keypad to be granted access. The access
mode is defined on GV-ASManager.

0~9 Number Keys:

Press the number keys to enter the PIN code.

# Key:

Press the # key to confirm the PIN code.

﹡

Key:

Press the

﹡

key to cancel the PIN code.

4. LED Indicator and Beeper

In standby mode, the LED is blue. When a card is read, the LED flashes green and the
beeper beeps once.

GV-RK1352 comes with the external control wires of Green LED, Red LED and Beeper.
When these control wires are connected to GV-AS Controller, the status of LED and Beeper
can be defined by GV-AS Controller. For details on how to configure the settings, refer to

6.Configuring the Beeper and LED Indicator

later in this installation guide.

5. Connecting GV-RK1352 to GV-AS Controller

The connection between GV-RK1352 and GV-AS Controller varies with different controller
models. The following diagrams illustrate

how to connect GV-RK1352 to GV-AS400

Controller

through Wiegand or RS-485 interface.

Note:

GV-RK1352 is compatible with GV-AS100/200/400 Controllers. However, to enable

the keypad function, you can only connect GV-RK1352 to GV-AS100/200 Controllers
through the Wiegand interface. For GV-AS400 Controller, the connection through either
Wiegand or RS-485 interface is workable for the keypad function.

September 23, 2010

5.1 Connecting through Wiegand Interface

Up to eight GV-RK1352 readers can be connected to GV-AS400 Controller through the
controller’s Wiegand interface.

Wire Color Function

Black GND
Green

Wiegand Data 0

White

Wiegand Data 1

Red

DC 12 V

5.2 Connecting through RS-485 Interface

Up to eight GV-RK1352 readers can be connected together to the RS-485 interface on GV-
AS400 Controller. When multiple readers are connected to the same RS-485 interface, you
need to specify each reader an ID so that the controller can distinguish one reader from
another. You will need to:

1. Connect GV-RK1352 readers to a computer to access the

GV-RK1352 Config AP

2. Define the ID number of each GV-RK1352 reader on the

GV-RK1352 Config AP

3. Wire GV-RK1352 readers to GV-AS Controller.

Note:

If only one GV-RK1352 reader is connected to GV-AS Controller through RS-485

interface, you can skip steps 1 and 2, and the default ID number for the reader will be 0.

5.2.1 Connecting GV-RK1352 to a Computer to Access GV-RK1352 Config AP

Using the

GV-RK1352 Config AP

included in the software CD, you can define the ID

numbers of multiple readers connected through RS-485 interface.

September 23, 2010

To start the

GV-RK1352 Config AP

, you have to connect GV-RK1352 to a computer through

GV-COM, GV-Hub or GV-NET/IO Card V3.1.

Wire Color Function

Blue RS-485

Light Blue

RS-485 -

Note:

GV-RK1352 is not compatible with GV-NET Card and GV-NET/IO Card of versions

earlier than V3.

5.2.2 Defining ID Numbers of Readers

After GV-RK1352 readers are connected to a computer, follow the steps below to define the
ID number of each GV-RK1352 reader:

1. Insert the software CD and the Install Program window will pop up automatically.

2. Select

Install GeoVision USB Devices Driver

3. In the GeoVision USB Driver Installer window that appears, select

Install

4. Go back to the Install Program window, and select

Run GV-RK1352 Config Utility

. This

dialog box appears.

September 23, 2010

5. Type the barcode number of GV-RK1352 in the Serial ID box. The barcode number is on

the rear panel of GV-RK1352.

6. Select the COM port that is connected to GV-RK1352 and click

Open COM

. The red

square next to the COM port box should change to blue to indicate the COM port is
correct.

Note:

If the COM port is incorrect, an “

Error opening serial port

”

message will appear.

To verify the COM port that is connected to GV-RK1352, go to Windows Device Manager.
In the Ports (COM & LPT) field, you should see the entry for

Prolific USB-to-Serial Comm

Port

. The COM port showing in the entry indicates the COM number currently in use.

7. Click

Setup GO

. The settings are sent to GV-RK1352.

Note:

If you select the wrong COM port of GV-RK1352, a “

Fail. Please check Serial ID

and comport

” message will appear when you click the

Setup GO

button. Go to Windows

Device Manager to find out the COM port of GV-RK1352.

September 23, 2010

5.2.3 Wiring GV-RK1352 to GV-AS Controller

After defining the ID number of the readers, you can connect the wires of GV-RK1352 to GV-
AS Controller. Here we use

GV-AS400 Controller

as example to illustrate the wiring.

Connecting four or less readers to GV-AS400 Controller:

Wire Color Function

Black GND
Light Blue

RS-485 -

Blue RS-485

Red

DC 12 V

Connecting five or more readers to GV-AS400 Controller:

For readers five to eight, connect the RS-485 cable to the RS-485 interface on GV-
AS400 Controller and then connect the 12V power output and GND of the reader to a
10V to 13V DC power output on the GV-AS Power Board.

Wire Color Function

Black GND
Light Blue

RS-485 -

Blue RS-485

Red

DC 12 V

September 23, 2010

6. Defining Readers on GV-AS Controller Web Interface

To define readers on the Web interface of GV-AS Controller, we use

GV-AS400 Controller

as example. Since GV-AS400 Controller can control up to four doors, you need to specify
which door each reader controls.

1. On the GV-AS400 Web interface, click

Extend Reader

. This dialog box appears.

2. Select the ID number of the reader and type its barcode number. The ID number should

be the same with the one you configure through the

GV-RK1352 Config AP

3. Select a door/gate for the reader from the Function drop-down list. Click

Submit

September 23, 2010

7. Configuring the Beeper and LED Indicator

You can configure the settings of the LED and the beeper by enabling the GV-AS Controller
to externally control the LED and Beeper. You will have to:

1. Set up the Beeper and LED settings of the reader by using the

GV-RK1352 Config AP

2. Wire the Beeper, Red LED and Green LED from GV-RK1352 to GV-AS Controller.

3. Specify the Beeper and LED settings for each door through the Web interface of GV-AS

Controller.

7.1 Setting up Beeper and LED on GV-RK1352 Config AP

To enable the external controls of the Beeper and LED, start the

GV-RK1352 Config AP

according to the instructions in

Accessing the GV-RK1352 Config AP

earlier in this

installation guide.

After

GV-RK1352 Config AP

is started, you have to enable the external controls and set the

GV-RK1352 to be slave.

1. Start the

GV-RK1352 Config AP

. Type the barcode number and the COM port of GV-

RK1352. The barcode number is on the rear panel of GV-RK1352. Refer to

Defining ID

Numbers of Readers

earlier in this installation guide on how to determine the COM port

of GV-RK1352.

September 23, 2010

2. To enable external control of Beeper or LED, select

Beeper

Green LED

Red LED

Beeper:

Enables the external control of Beeper.

Green LED:

Changes the standby color to green.

Red LED:

Changes the standby color to red.

3. Select

Slave

from the Master / Slave drop-down list and select an ID number for the

reader. The ID number is ranging from 0 to 7.

4. Click

Setup GO

. The settings are sent to GV-RK1352.

After the above settings, you need to connect the Beeper, Red LED and Green LED wires
from GV-RK1352 to GV-AS Controller

7.2 Wiring the Beeper and LED to GV-AS Controller

To wire the beeper and LED to GV-AS Controller, we use

GV-AS400 Controller

as example.

Connect the control wires of GV-RK1352’s Beeper, Red LED or Green LED to any of outputs
9 ~ 16 on GV-AS400 Controller. The following diagram is an example on connecting the
beeper wire of GV-RK1352 to GV-AS400 Controller.

Wire Color Function

Black GND
Yellow

Beeper

September 23, 2010

7.3 Configuring the Beeper and LED Settings for Each Door/Gate

After connecting the wires for Beeper or LED, specify the Beeper or LED settings for each
door/gate on the GV-AS Web interface. Here we use

GV-AS400 Controller

as example.

1. On the GV-AS400 Web interface, click

Output Setting

. The page below appears.

2. From the output 9~12, select a door and select

Beeper

Green LED

Red LED

Invert

Red LED

. Click

Submit

Beeper:

Enables the external control of Beeper.

Green LED:

Changes the standby color to green.

When a card is read, the LED

flashes green.

RED LED:

Changes the standby color to red. When a card is granted access, the

LED flashes green. When a card is failed to be granted access, the LED turns off for
a very short time and then turns Red.

Invert Red LED:

Changes the standby color to no light. When a card is granted

access, the LED flashes green. When a card is failed to be granted access, the LED
flashes red.

September 23, 2010

8. Firmware Upgrade

GeoVision will periodically release the updated firmware on the website. The new firmware
can be simply loaded into GV-RK1352 by using

Upload Application

included in the

Software CD.

Important Notes before You Start

Before you start updating the firmware, please read these important notes:

1. While the firmware is being updated, the power supply must not be interrupted.

2. Do not turn the power off within 10 minutes after the firmware is updated.

WARNING:

The interruption of power supply during updating causes not only update

failures but also damages to the device. In this case, please contact your sales
representative and send your device back to GeoVision for repair.

To upgrade firmware:

1. Insert the Software CD, select

Upload Application

, and

follow the onscreen instructions

to install the program.

2. Double-click the

Upload Application

icon created on your desktop. This dialog box

appears.

3. Select the COM port of GV-RK1352.

4. Click the

Browse

button to locate the firmware file (.img) saved at your local computer.

5. Click

Update

6. The LED indicator should flash purple during the process of firmware upgrading. When

the process is complete, GV-RK1352 will be sounded twice and the LED indicator will
change to green.

September 23, 2010

9. Specifications

CPU

8 bit microprocessor

Frequency

13.56 MHz for ISO14443A

Wiegand Interface

Wiegand 26 bit, distance 30 m / 98.43 ft

RS-485

9,600 bps, connect up to 8 GV-RK1352 units

Power

DC 7.5 V ~ 12 V

LED

Red, Green and Blue LED

Beeper

Buzzer

Reader Color

Black

Operating Temperature

-20 °C ~ 60 °C / -4 °F ~ 140 °F

Operating Humidity

10% ~ 90% (no condensation)

Dimensions (W x H x D)

95 x 108 x 23 mm / 3.74 x 4.25 x 0.91 in

Weight

260 g / 0.57 lb

Certification

IP66, CE, FCC

10. The number of GV-RK1352 supported by GV-AS

Controllers

GV-RK1352 Interface

GV-AS Controller Model

Wiegand

RS-485

GV-AS100

Not support

GV-AS100 with GV-ASBOX

GV-AS200

GV-AS400

Ask a Question ?