GeoVision GV- DFR1352 Installation Manual - User Manual

Full Text Searchable PDF User Manual

GV- DFR1352 Card Reader

The GV-DFR1352 is a card reader designed to recognize identification cards. Featured with
the Wiegand and RS-485 outputs, the unit can be connected to any standard access control
panel. GV-DFR1352 comes with a weather sealed and IP66 compliant housing for outdoor
use.

1. Packing List

GV-DFR1352 Card Reader

Screw x 2

Screw Anchor x 2

Front Cover Plate x 2

GV-DFR1352 Software CD

Front View

2. Installation

Install the GV-DFR1352 to the door frame using the supplied screws and screw anchors.
Before placing and sticking the front cover plate to the GV-DFR1352, remove the Plastic
Cover to prevent scratches to the cover after installed.

April 24, 2014

3. Electric Wire

Wire Color

Function

Red DC

12V

Black GND
Yellow Beeper
Orange Green

LED

Light Red

Red LED

Green

Wiegand Data 0

White

Wiegand Data 1

Blue RS-485

Light Blue

RS-485 -

Gray N/A
Purple N/A
Brown N/A

Rear View

4. LED Indicator and Beeper

In standby mode, the LED is blue. When a card is read, the LED flashes green and the
beeper beeps once.

GV-DFR1352 comes with external control wires for Green LED, Red LED and Beeper. You
can connect these control wires to a GV-AS400 / 410 / 810 to allow the status of LED and
Beeper to be defined by the GV-AS400 / 410 / 810. For details on how to configure the
settings, refer to

7. Enabling External Control of the Beeper and LED

later in this installation

guide.

5. Connecting GV-DFR1352 to GV-AS Controller

GV-DFR1352 can be connected to GV-AS100 / 110 / 120 / 210 / 400 / 410 / 810. To see how
many readers can be connected to a GV-AS Controller, refer to

The number of GV-DFR1352

supported by GV-AS Controllers

table at the end of this installation guide.

The connection between GV-DFR1352 and the controller varies with different controller
models. The following diagrams illustrate

how to connect GV-DFR1352 to GV-AS810

Controller

through Wiegand or RS-485 interface.

April 24, 2014

5.1 Connecting through Wiegand Interface

Up to eight GV-DFR1352 readers can be connected to GV-AS810 Controller through the
controller’s Wiegand interface.

Wire Color

Function

Black GND
White

Wiegand Data 1

Green

Wiegand Data 0

Red DC

12V

5.2 Connecting through RS-485 Interface

Up to eight GV-DFR1352 readers can be connected together to the RS-485 interface on GV-
AS810 Controller.



Connecting four or less readers to GV-AS810 Controller:

Wire Color

Function

Black GND
Light Blue

RS-485 -

Blue RS-485

Red DC

12V

485

April 24, 2014



Connecting five or more readers to GV-AS810 Controller:

For readers five to eight, connect the RS-485 cable to the RS-485 interface on GV-
AS810 and then connect the 12V power output and GND of the reader to a 12V power
output on the controller.

RS4

5.2.1 Defining Readers on GV-AS Controller Web Interface

Since multiple readers can connect to GV-AS Controller using one RS-485 interface, you
need to specify which door each reader controls. This section explains how to define readers
on the Web interface of GV-AS Controller using

GV-AS210 Controller

as an example.

1. On the GV-AS210 Web interface, click

Extended Reader

. This dialog box appears.

2. In the GV-Reader/CR420/GF1921/GF1922 section, select the

RS485

checkbox in front of

the ID number and type the

Serial Number

on the rear panel of the reader. The ID

number will be assigned to the reader.

3. Select a door/gate for the reader from the

Function

drop-down list. Click

Submit

April 24, 2014

Note:

When you click

Submit

on the Extended Reader page of a GV-AS210 / 410 / 810,

all GV-RK1352 / R1352 / DFR1352 connected through RS-485 interface will reboot.

6. Overlaying Card Numbers on GV-System Live View

You can overlay card numbers recognized at the GV-DFR1352 onto a camera channel on
GV-System. To overlay card numbers on GV-System channel, the reader needs to be
connected to a GV-System through GV-COM, GV-Hub or GV-NET/IO Card V3.1.

GV-DFR1352

RS-485

GV-HUB / GV-COM /

GV-NET/IO Card

RS-232

GV-System

(Light Blue) RS-485 -

(Blue) RS-485 +

USB

Note:

GV-DFR1352 is not compatible with GV-NET Card and GV-NET/IO Card of versions

earlier than V3.

6.1 Defining the ID Number and Setting the Reader to Slave

After the reader is connected to the computer of the GV-System, use the

GV-Reader Config

in the software CD to define the ID number of the reader and set the reader to Slave.

1. Insert the software CD. The Install Program window will pop up automatically.

2. Select

Install GeoVision USB Devices Driver

3. In the GeoVision USB Driver Installer window that appears, select

Install

April 24, 2014

4. Go back to the Install Program window, and select

Run GV-Reader Config Utility

5. Select the COM port that is connected to GV-DFR1352 and click

Open COM

. The serial

number and firmware version of the reader will be automatically detected. The red square
next to the COM port box should change to blue to indicate the COM port is correct.

6. Under

Master / Slave

, set the reader to

Slave

7. Select an

ID Number

for the reader. The ID number ranges from 0 to 7.

8. Click

Setup

. The settings are sent to GV-DFR1352.

If you want to connect multiple readers to the GV-System, you need to set up a unique ID
number for each reader. For this you need to connect each reader to the computer one
reader at a time, and follow the instructions above to set up an ID number.

Note:

1. If the COM port is incorrect, an “

Error opening serial port

”

message will appear. To

verify the COM port that is connected to GV-DFR1352, go to Windows Device
Manager. In the Ports (COM & LPT) field, you should see the entry for

Prolific USB-to-

Serial Comm Port

and the COM number currently in use.

2. If you are using an older version of the GV-Reader Config AP, you will have to

manually type the serial number of GV-DFR1352. The serial number is on the rear
panel of GV-DFR1352.

April 24, 2014

6.2 Adding the Reader to GV-System

1. In GV-System, click the

Configure

button, select

Accessories

, and select

GV Wiegand

Capture Device Setting

. This dialog box appears.

2. Click the

New

button. This dialog box appears.



Type:

Select GV-Wiegand Capture.



Device:

Type a number and name to help you identify the reader.



COM:

Select the COM port connected to the reader.



Address:

Select the ID of the connected reader you set in GV-Reader Config AP.



Camera:

Assign the reader to a channel to overlay card numbers on the live view.

April 24, 2014

3. Click the

Add

button.

7. Enabling External Control the Beeper and LED

You can change the default settings of the LED and the beeper by enabling a GV-AS400 /
410 / 810 to externally control the LED and Beeper. The GV-AS Controller and the reader
need to be connected through Wiegand interface. You will have to:

1. Enable external control of the GV-DFR1352’s Beeper and LED by using the

GV-Reader

Config AP

. Refer to

7.1 Setting up Beeper and LED on GV-Reader Config AP

2. Wire the Beeper, Red LED and Green LED from GV-DFR1352 to GV-AS400 / 410 / 810.

3. Specify the Beeper and LED settings for each door through the Web interface of GV-

AS400 / 410 / 810.

7.1 Setting up Beeper and LED on GV-Reader Config AP

To enable the external controls of the Beeper and LED on GV-Reader Config AP, the reader
needs to be connected to a computer through GV-COM, GV-Hub or GV-NET/IO Card V3.1.

1. Install

GV-Reader Config AP

from the Software CD.

2. Start the

GV-Reader Config AP

and select the COM port that is connected to GV-

DFR1352.

Note:

To see how to install the GV-Reader Config AP and how to identify the COM port of

the reader, refer to

6.1 Defining the ID Number and Setting the Reader to Slave

earlier in

this installation guide

April 24, 2014

3. Click

Open COM

. The serial number and the firmware version of the reader will be

automatically detected.

4. To enable external control of Beeper or LED, select

Beeper

Green LED

Red LED



Beeper:

Enables the external control of Beeper.



Green LED:

Changes the standby color from blue to green.



Red LED:

Changes the standby color from blue to red.

5. Select

Master

from the Master / Slave drop-down list.

6. Select an ID number for the reader. Make sure the ID number on the GV-Reader Config

AP matches the ID number set on the Extended Reader page of the GV-AS400 / 410 /
810 Web interface.

7. Click

Setup

. The settings are sent to GV-DFR1352.

If you want to set up multiple readers to be controlled by the controller, you need to connect
each reader to the computer one reader at a time, and follow the above instructions to
enable external control.

After the above settings, connect the Beeper, Red LED and Green LED wires from GV-
DFR1352 to GV-AS400 / 410 / 810.

April 24, 2014

7.2 Wiring the Beeper and LED to GV-AS400 / 410 / 810

To wire the beeper and LED to GV-AS400 / 410 / 810, connect the control wires of GV-
DFR1352’s Beeper, Red LED or Green LED to any of outputs 9 ~ 16 on GV-AS Controller.

Wiring LED to GV-AS Controller

The diagram below shows the connection for wiring Green LED on GV-AS810. For Red LED,
use the light red wire instead.

Wire Color

Function

Black GND
Orange Green

LED

Light Red

Red LED

Wiring Beeper to GV-AS Controller

The diagram below shows the connection for wiring the beeper on GV-AS810.

Wire Color

Function

Black GND
Yellow

Beeper

After wiring, you also need to go to GV-ASManager to select the alarm conditions that will set
off the reader’s beeper. In GV-ASManager, right-click the GV-AS Controller in the device list,
click

Settings

, and click the

Door / Gate

tab to select the alarm conditions.

April 24, 2014

7.3 Configuring the Beeper and LED Settings for Each Door/Gate

After connecting the wires for Beeper or LED, specify the Beeper or LED settings for each
door/gate on the GV-AS400 / 410 / 810 Web interface.

1. On the controller Web interface, click

Output Setting

. The page below appears.

2. From outputs 9~12, select a door and select

Beeper

Green LED

Red LED

Invert

Red LED

. Click

Submit



Beeper:

Enables the external control of Beeper.



Green LED:

Changes the standby color to blue.

When a card is read, the LED

flashes green.



RED LED:

Changes the standby color to red. When a card is read, the LED flashes

blue.



Invert Red LED:

Changes the standby color to blue. When a card is read, the LED

flashes red.

April 24, 2014

8. Firmware Upgrade

GeoVision will periodically release the updated firmware on the website. You can also find
the latest firmware from the Firmware folder in the Software CD. The new firmware can be
simply loaded into GV-DFR1352 by using

Update Utility

included in the Software CD.

Important Notes before You Start

Before you start updating the firmware, please read these important notes:

1. While the firmware is being updated, the power supply must not be interrupted.

2. Do not turn the power off within 10 minutes after the firmware is updated.

WARNING:

The interruption of power supply during updating causes not only update

failures but also damages to the device. In this case, please contact your sales
representative and send your device back to GeoVision for repair.

To upgrade firmware:

1. Insert the Software CD, and select

Run Firmware Update Utility

. This dialog box

appears.

2. Select the COM port of GV-DFR1352.

3. Click the

Browse

button to locate the firmware file (.img) saved at your local computer.

4. Click

Update

April 24, 2014

5. The LED indicator should flash purple during the process of firmware upgrading. When

the process is complete, GV-DFR1352 will be sounded twice and the LED indicator will
change to green.

April 24, 2014

9. Specifications

CPU

8-bit microprocessor

Frequency

13.56 MHz for ISO14443A (Mifare DESFire, Mifare
Plus and Mifare Class)

Wiegand Interface

Wiegand 26 / 34 bits, distance 30 m / 98.43 ft

RS-485

9,600 bps, connect up to 8 GV-DFR1352 units

Power

DC 7.5V – 12V

LED

Red, Green and Blue LED

Beeper

Buzzer

Reader Color

Black

Operating Temperature

-30 °C ~ 65 °C / -22 °F ~ 149 °F

Operating Humidity

10% ~ 90% (no condensation)

Dimensions (W x H x D)

20.9 x 105.6 x 20.5 mm / 0.8 x 4.2 x 0.8 in

Weight

80 g / 0.17 lb

Ingress Protection

IP66

Certification

CE, FCC, RoHS

10. The number of GV-DFR1352 supported by GV-AS

Controllers

GV-DFR1352 Interface

GV-AS Controller Model

Wiegand

RS-485

GV-AS100

GV-AS110 / 120

Not supported

GV-AS100 / 110 / 120 with GV-ASBox

GV-AS100 / 110 / 120 with GV-ASNet

Not supported

GV-AS210 4

GV-AS400

GV-AS410 / 810

Ask a Question ?