Full Text Searchable PDF User Manual
Set-up guide
Cosy
2
Important safety notice
j
The following safety regulations must be observed at all times.
Failure to observe precautions could result in severe injury or death.
This product must only be installed by a competent person.
h
It is important to observe some simple safety precautions when installing and using this
product. Read this important information before continuing. Safe operation of the unit is
impaired if not used or installed in a manner specified by the manufacturer.
r
Isolate mains supply before removing the switch cover. When connected to a live mains
supply, all internal parts are at mains potential. No user serviceable parts inside.
j
For use in dry, indoor environments only.
n
This product is double insulated.
l
At the end of its life please recycle at a suitable recycling facility. Do not place in general
waste.
s
The display contains a non-replaceable Ni-MH battery pack. It can be removed by
dismantling the unit for recycling purposes only and must be disposed of at a suitable
recycling facility. Do not place in general waste.
m
These units have been tested and conform to all relevant European safety and regulatory
standards where applicable but not limited to the following: EN 60730-2-9:2010 with EN
60730-1:2000 + A1:2004 + A12:2003 + A13:2004 + A14:2005 + A15:2007 + A16:2007 +
A2:2008 (Excluding clauses: H.23, H.26 and Annex ZF); EN 60950-1:2005 (Second edition),
Am 1:2009; EN 300-220-1; EN 301-489-1.
3
Getting started
There are two steps.
•
Setting up:
powering up and getting to know Cosy
•
Installing the switch or switches:
this will be completed by the installer or, if you have bought
Cosy without installation being included, you will need to arrange for an electrician to install the
switch/es.
Check contents of the box
Setting up
(set-up guide)
Switch installation
(switch installation instructions)
Arrange for the installer/an electrician to call
Install the switch/es
Switch updates
Download app and view videos
Associate hub (on completion of updates)
Installer/electrician tests the system
The system is now in Demo mode
The system is now live
Plug in the hub system and display -
updates
customer
installer / electrician
4
Setting up
5
Setting up
1
. Place the hub beside your broadband
router and connect it up
•
Assemble the power adapter, plug it in and
connect it to the hub
•
Connect the hub to your broadband router
using the Ethernet cable supplied
•
The LED light by the cloud on the right of
the hub will turn green, the one on the left
will turn amber
2
. The system will automatically connect
to the internet and download the most
recent firmware
•
This can take around 5 minutes during
which the LED lights on the hub will flash
amber
•
During this time connect up the display
(step 3)
•
Once this is done, both hub LEDs will be
green and the display will show the current
temperature
3
. Connect up the display (you can put
this anywhere for now)
•
Assemble the power adapter, plug in to
the charging base, plug into the mains and
switch on
•
Remove the battery tab
from the bottom of
the display unit and place on the charging
base
•
The display will show the current
temperature.
4
. Whilst the system is updating, on a
web browser:
•
Go to
www.comehometocosy.com/app
,
download the app and register
•
Go to
www.comehometocosy.com/videos
and view the videos
•
Go to
www.comehometocosy.com/support
and explore the support pages
5
. When the hub LEDs are green
associate the hub with your Cosy
account so that you can use the app
•
Open the app and follow the instructions
for associating the hub
6
Demo mode
7
Demo mode
You can now interact with Cosy as though it’s live but you can’t control the heat just yet.
Things you can do before the switch is installed
•
Set your temperature settings
for each of the lifestyle modes (settings > temperatures). Select
the mode and rotate the dial to the right temperature. On iOS devices you need to tap the dial
first to set the temperature and again to save it.
•
Look at the default profiles (settings > schedules > profiles > weekday). Try altering and
changing events, look at the weekday profile or
add your own profile.
•
Select the profile you wish
for each day of the week (settings > schedules).
•
If you need to,
add additional users.
They’ll need to download the app and follow the
instructions.
•
Take the Cosy display to where you would like to use it most often and see what temperature
it reads.
•
Do not position the Cosy display near a heat source (such as a radiator or a light) and avoid
direct sunlight.
8
Installing the Heating switch
9
Installing the Heating switch
The switch is a mains powered thermostat switch.
It works in addition to your existing thermostat
-
which can stay where it is - so no redecorating required!
The switch can control the heating for up to 2 zones, however you will need to purchase an
additional Cosy Display for each additional zone.
The switch requires a
competent electrician to install it
and takes 15-45 minutes to install and test.
If you have bought Cosy with installation an installer will contact you and arrange a time and date to
come and install your switch, test the system and make sure you are entirely happy with your Cosy.
If you have bought Cosy without installation you will need to arrange an installation yourself.
Go to
www.comehometocosy.com/support
where you will be able to download the Heating Switch
Installation Instructions.
When the installer/electrician arrives give them the Cosy Heating switch installation instructions, the
Cosy switch box and show them your heating system.
Once the electrician has installed the switch/es they should test the system to check that your
heating is up and running.
For the system to work properly you need to check three things:
•
The switch/es are active
(the centre button is green when switched on)
•
Your previous thermostat is set to maximum
(if you have one)
•
Your heating is set to always on
10
Installing the Hot Water switch
11
MID-POSITION
VALVE
PUMP
FLOW
Y-plan
RETURN
BOILER
ZONE
VALVE
ZONE
VALVE
PUMP
FLOW
RETURN
BOILER
S-plan
Installing the Hot Water switch
If you have a hot water tank with a Y or S plan
system (see right) Cosy can also be used to
control your hot water. To control the hot water
please purchase a hot water extension pack.
The switch is a mains powered switch and
requires a
competent electrician to install it
and
takes 15-45 minutes to install and test.
If you have bought Cosy with installation an
installer will contact you and arrange a time and
date to come and install your switch, test the
system and make sure you are entirely happy
with your Cosy.
If you have bought Cosy without installation you
will need to arrange an installation yourself.
Go to
www.comehometocosy.com/support
where you will be able to download the Hot
Water Switch Installation Instructions.
When the installer/electrician arrives give
them the Cosy Hot Water switch installation
instructions, the Cosy switch box and show
them your hot water system.
Once the electrician has installed the switch
they should test the system to check that your
heating and hot water are up and running.
For the system to work properly you need to
check two things:
•
The switch is active
(the centre button is
green when switched on)
•
Your existing controller is set to constant
hot water
(if you have one)
3 port valve
2 port valve
comehometocosy.com
If you have any questions you can check
www.comehometocosy.com/support
or call the support team on
0845 094 1508
. Office hours are 9-5.30 Monday-Friday.
Cosy
COSY-Z-USG-105_3