Full Text Searchable PDF User Manual
Business²
Hand dryer
High Speed
Operating Instructions and Parts Manual
Surface Mounted High Speed Hand Dryer
Technical Specifications
Item Category
Performance Data
Operating Voltage
220 - 240Vac, 50 Hz, 800 watts (heater off) 1600 watts (heater on)
Warm Air Speed Output
110 m/s
Display
LED countdown
Motor Type
35,000 rpm, ICP Brushless DC
Motor Thermal Protection
Auto Resetting Thermostat turns unit off, 240V at 221°F (105°C) - EURO Spec
Heater Element
0 - 800 WATTS
Heater Thermal Protection
Auto resetting
Drying Time
Less than 10 seconds
Circuit Operation
Infared Automatic, self adjusting
Timing Protection
30 seconds auto shut off
Drip Proof
IP22
Isolation
CLASS I
Net Weight
8.5 kg
Shipping Weight
10 kg
Unit Size
300mm W x 608mm H x 250mm D
Item Code
Cover Type/Finish
BB702W
ABS White
BB702S
ABS Metallic silver
BB702T
ABS Silver/White two tone
Business
1
608mm
300mm
250mm
Operating Instructions and Parts Manual
Surface Mounted High Speed Hand Dryer
Business
2
General Safety Information
This product is intended for installation by a
qualified service person. Use AWAG No.16 solid
conductor for wiring.
Failure to properly ground unit could result in
electrical shock and/or death.
Disconnect power at the service breaker before
installing or servicing.
NOT FOR HOUSEHOLD USE - MAY CAUSE BURNS
“IMPROPRE A L’USAGE DOMESTIQUE - PUET
OCCASIONNER.”
All units must be supplied with a 2-wire service. The
ground wire must be connected with the dryers
back plate.
•
WARNING
NOTE: Do not install dryer over wash basin.
Type Y attachment
If the power supply cord is damaged, it must be
replaced by the manufacturer or its service agent or a
similar qualified person in order to avoid a hazard.
Means for disconnection must be incorporated in the
fixed wiring in accordance with the wiring rules.
Installation
1. Make sure power supply breaker is switched off.
Installation must be carried out in accordance with the
current edition of the local wiring regulations code
having jurisdiction. Installation should be performed
only by a qualified electrician.
2. Place template against wall at desired height
(see mounting height recommendations) and mark
locations of 4 mounting holes and wire service entry at
knockout (KO) location.
NOTE: For two or more dryers, dryers should be no
closer than 24 inches (610 mm) on centre.
3. Remove and retain 2 cover screws.
4. Connect supply wires to terminal block where
indicated and connect ground wire to baseplate with
ground screw.
Connections:
a. Connect the live wire (coloured red or brown) to
the terminal block marked “L”.
b. Connect the neutral wire (coloured black or blue)
to the terminal block marked “N”.
Note that the colour of live and neutral wires depends
on voltage of supply service.
5. Replace cover screens. Do not over-tighten.
Operating Instructions and Parts Manual
Surface Mounted High Speed Hand Dryer
Business
3
Recommended Mounting Heights
Consumables
Operation
• No touch operation.
• Shake excess water from hands.
• Place hands onto the aperture.
• Move hands up and down.
• Green LEDs count down drying time.
• Stops automatically after hands are removed.
Men’s
Ladies
Children, ages 11-17 Children, ages 3-10
Disabled
13”
11”
10”
6”
4”
350 mm
300 mm
250 mm
150 mm
100 mm
Product
Order Code
Antibacterial HEPA filter
HD-BUSI-HEPA-FILTER
Moisturising Gel
BB70GELS
From floor to bottom of dryer.
Biodrier Anti Bacterial Filter
The Anti Bacterial Filter is fitted to ensure dust and air-
borne bacterias are restricted from entering the internal
components and airflow of the dryer. The filter should
be replaced every 3-6 months, depending on usage.
Biodrier Gels
Biodrier Gels are manufactured exclusively for Biodrier
and preforms 3 jobs in one:
1. Moisturise the hands.
2. Sanitise the product internally, and the users hands.
3. Fragrances the surrounding washroom area whilst in use.
The Gels are manufactured from natural sources and are
chemical free.
4. Clean filter casing by wiping with soft
damp cloth. Replace the antibacterial
filter every 3 months. Slide filter back
into place.
1. Pour a cup of water
down drain hole. Use
cleaning brush supplied
to clean drain hole.
2. Remove drain tank
and empty.
5. Disassemble drain tank and
rinse clean using a disinfectant,
then replace. Moisturising gels
should be replaced every month.
3. Remove filter.
6. Wipe down the external
surfaces of the Biodrier
Business hand dryer with a soft
cloth. Switch power back on
and test operation.
Operating Instructions and Parts Manual
Surface Mounted High Speed Hand Dryer
Business
4
Cleaning and Maintenance Instructions
•
WARNING
• Never spray water directly onto hand dryer
• Never use any abrasives or harsh chemicals
• Turn off electricity prior to cleaning the hand dryer
Periodic cleaning of the unit is recommended to
ensure optimum performance.
• Switch to service mode located on the top left side of
the dryer.
• Wipe the cover with a soft cloth and a mild cleaning
solution. Do not Soak. Never use abrasives to clean
the cover.
Place Gels
here
Operating Instructions and Parts Manual
Surface Mounted High Speed Hand Dryer
Diagram
Business
5
Operating Instructions and Parts Manual
Surface Mounted High Speed Hand Dryer
Parts List
Business
6
Key
Description
1
Cover
2
Fan house cover
3
LED light
4
Fan house cover
5
Air outlet
6
Eradiating screen
7
Left side board
8
Incept screen
9
Lighting screen
10
Air outlet
11
Door of power switch
12
Fan house cover
13
Display screen ornament
14
Sensor light PCB
15
Sensor PCB module
16
Left fixer
17
Lighting PCB module
18
Fan house cover
19
Switch button
20
USB port
Key
Description
21
Bracket
22
Big pothook
23
Fixing board
24
Small pothook
25
PP seal board
26
Right fixer
27
Connector
28
Base plate
29
Hose
30
Motor PCB
31
Right side board
32
Filter
33
Water tank
34
Lock
35
Heater
36
Passage
37
Motor cover
38
Fan house module
39
Motor bracket
40
Motor module