Full Text Searchable PDF User Manual
SERVICE MANUAL
PenSketch 9X12
Version 1.0
0
Tablet of Contents
Preface
…………………………………………………………………………… 1
Chapter 1. Introduction of Tablet
…………………………………………… 1
Chapter 2. Diagnose Problems
………………………………………………. 3
2.1 Distinguish the Problems …………………………………………………... 3
2.2 Define the Problems ………………………………………………………... 3
2.3 Analyses of the Problems …………………………………………………... 4
Chapter 3. Disassembly and Replacement
………………………………... 5
3.1 Assembly of Tablet …………………………………………………………. 5
3.2 How to Disassemble the Tablet and Replace the Components …………….. 6
3.3 Mal-functions of Digital Pen ……………………………………………… 8
3.4 Change Pen Tip and Battery ………………………………………………... 9
3.5 Mal-functions of Digital Mouse …………………………………………... 10
3.6 Change Digital Mouse Battery ……………………………………………. 10
Chapter 4. Important Notes
…………………………………………………. 11
Appendix
-
Part Lists
………………………………………………………… 11
1
Preface
The service guide is divided into four sections and provides the basic instructions
related to our tablet products. The four sections consist of
Introduction of Tablet
,
Diagnose Problems
,
Disassembly and Replacement
, and
Important Notes
. You can
follow the instructions of service guide to diagnose the problems caused by tablet
mal-function and replace simply the tablet by yourself.
Chapter 1. Introduction of Tablet
The tablet consists of a digital pen and a tablet. The tablet applies electromagnetic
technology to receive signals from digital pen and position the cursor on the screen.
The main functions of the digital pen and the tablet appearances are described as
below.
Pen
Indicator
Hot Cell
Working
Area
Figure 1. Tablet
Pen Holder
The place digital pen is put.
Pen Indicator
The green LED light is the key indicator for hardware verification. The green light
comes on when the digital pen closes or touches the tablet or system is detecting
the tablet.
Working Area
The tablet can detect accurately pen position and pressure in this area. You can
adjust the size of working area through
PenLauncher
setting.
2
Hot Cells and Symbols
Users can implement directly certain commands or programs by tapping hot cells
and symbols on the tablet. The detailed Hot Cell setting is described in
Driver
Manual.
Figure 2. Digital Pressure Pen
Pen Tip
The pen tip’s functions are same as mouse’s left button but it possesses pressure
sensitivity. Users can operate pressure pen as real writing and drawing situation.
Barrel Button 1
The functions are same as mouse’s middle button or scroll wheel. When users press
the barrel button of digital pen to move the page you want to read.
Barrel Button 2
The functions are same as mouse’s right button to call out the function menu.
Pen Tip
Barrel Button 1
Barrel Button 2
Left-Button
Right-Button
Scroll Button
Figure 3. Digital Mouse
Left Button
Mouse left button
Right Button
Mouse right button
Scroll Button
Scroll button simulates mouse scroll wheel function. Users can push the scroll
button up and down to control screen pages.
3
Chapter 2. Diagnose Problems
2.1 Distinguish the Problems
The problems could be made by software, hardware or mechanism. Users can follow
the simple steps to judge what reasons is belonged to.
Figure 4. Initial Self-Diagnose Problem
For software problems, they could be related to programs incompatible or system
wrong setting. Users can re-install our latest version driver or programs or contact our
customer service. In this service guide, we focus on the checking and replacing
tablet’s hardware problems.
2.2 Define the Problems
To realize the problems caused by hardware’s mal-function, we shall follow the steps
in
Figure 4
and observe these conditions. We summarize several probably problems
and these reasons and solutions of these problems are analyzed in
Tablet 1
.
4
Figure 5. Diagnose Symptoms
2.3 Analyses of the Problems
Problems
Condition Description
Probable Reasons
Solutions
1. Hardware
Not
Recognized
When tablet connects with
computer, LED light is
constantly twinkling. It shows
system is searching hardware
but can’t recognize hardware.
Or hardware is recognized as
Human Interface Device but
not as Tablet Pointing Device
1. Incompatible with
computer system
or hardware
2. PCB
defect
3. USB
Cable
defect
1. Restart PC or
Reinstall driver
2. Change
PCB
3. Change
USB
Cable
2. No Response
When tablet connects with
computer, the LED doesn’t
come on and system doesn’t
search hardware.
1. PCB
defect
2. USB cable defect
1. Change
PCB
2. Change
or
re-assemble
USB cable
3. No Response
Hardware can be recognized
but tablet doesn’t work
1. PCB
defect
2. Digital
pen
mal-function
1. Change
PCB
2. Check
digital
pen
4. No LED Light
Tablet can work but no LED
light
1. LED
defect
2. PCB
defect
Change PCB
5. Cursor not be
Positioned and
Jump Away
Randomly
When digital pen move to the
certain area of tablet, the
cursor jumps to another place
of the screen.
1. PCB Defect
Change PCB
6. Cursor
Trembling
When digital pen tip closes to
or touches with tablet, the
cursor is trembling and can’t
stop in the certain point.
1. Digital pen low
battery power
2. Digital pen defect
3.
GND springs is
1. Change
battery
2. Change
digital
pen
3. Adjust the
5
not contacted
with rear flat well
tightness of
screw near
PCB
7. No Response in
Certain Area
In the certain area of tablet,
users can’t write, draw or move
cursor.
PCB defect
Change PCB
8. Barrel
Buttons
No Response
No response in pressing barrel
buttons
Digital pen defect
Change digital pen
Tablet 1. Analysis of Problems
Chapter 3.
Disassembly and Replacement
3.1 Assembly of Tablet
The tablet components consist of membrane, PCB, cover, rear flat, and so on.
Figure
6
shows all components to assemble a tablet and you can know the kinds of tablet
components and standard numbers a tablet needs in
Appendix 1
.
Cover Sheet
Upper Case
LED Light Cover
USB Cable
PCBA
Isolate Metal
Isolate Plastic
Gasket
Pad
Screw
Bottom Case
FCC Label
Figure 6. The Components of PenSketch 9x12 Tablet
6
3.2 How to Disassemble the Tablet and Replace the Components
To replace the components of tablet, you have to realize each step of disassembling
and the probably problems caused by assembling process or defect components
Step Description
Picture
1. Turn
over
tablet
To disassemble the tablet, you
have to turn over tablet. You can
see several pads and screws.
Please note some screws are
under pads.
2. Take off pads Pads are pasted on rear flat so you
can take off all of them by hand.
3. Loose
screws
Using screwdriver to loose all
screws.
If the screw is loosen, it causes
rubber strap can’t press the
membrane tightly.
4. Take
apart
rear flat
After taking all screws off, you can
take up rear flat.
If rear flat is not placed well, rubber
rims and the rubber strap may be
loosened and moved.
7
5. Take
apart
isolate metal
After take up rear flat, you can take
up isolate metal.
Be care of the metal knife finger!
6. Take
apart
isolate
plastic
After take up isolate metal, you can
take up isolate plastic.
7. Take
apart
PCB
After PCBA is taken up. You can
also take apart PCBA from upper
case.
PCBA is the most important part of
tablet. It controls USB
communication interface and LED
light.
8. Pull out USB
plug
USB cable is connected to PCB.
Whatever replaces USB cable or
PCB, you have to separate them.
LED light is also welded on the
PCB so you have to replace the
whole PCB when LED light is
mal-function
8
3.3 Mal-functions of Digital Pen
The digital pen is not designed for replacing the components by users themselves
because it has more fine design and needs detailed adjustment. We suggest that you
can change a new one if the digital pen is broken.
Problems Condition
Description
Reasons
Not write or control
cursor
There is no response when user
operates digital pen
1. Digital pen defect
2. Pen is still in “Standby
Mode”, not “wakes up”
No pressure
User can’t write or draw the different
thickness of line by pressing pen tip on
tablet.
1. Digital pen defect
2. Driver is not installed
3. System can not
recognition tablet
Inking automatically
The pen doesn’t touch with the tablet
but it can “ink” automatically
Digital pen defect
Barrel buttons no
response
No response in pressing barrel buttons Barrel button defect
Cursor Trembling
When digital pen tip closes to or
touches with tablet, the cursor is
trembling and can’t stop in the certain
point.
Low battery power, voltage is
not stable
Table 2. The Symptoms of Digital Pen’s Mal-function
9
3.4 Change Pen Tip and Battery
The digital pen tip could become flat after using for a period of time. The blunt pen
tip can not affect normal using way but you can still change a new pen tip for their
digital pen. The following figures shows how to use pliers to pull out the pen tip from
the digital pen.
A. Pull out pen tip.
B. Push in pen tip.
There are several points must be attention when you replace the pen tip. First, don’t
use the sharp part of pliers to hold the pen tip in order to prevent cutting off the pen
tip. Once the pen tip is cut off, you can not pull out the pen tip anymore. Second,
when you put a new pen tip inside the pen, the new pen tip must be pressed forcibly in
order to make sure the new pen tip can be jointed tightly. If the pen tip can not be set
in correct position, it will influence the digital pen sending signal to tablet.
When the battery within the digital pen is running out, you can shell follow the
instrument of
Driver Manual
to change a new 1.5V, AAA alkaline battery.
A. Shell Step
10
B. Dressing Step
Note: The direction of arrow must aim the metal positive pole on Step 3.
3.5 Mal-functions of Digital Mouse
Users could have the problems in using digital mouse as bellows:
Problems Condition
Reasons
Not control cursor
There is no response when user
operates digital pen
Digital mouse defect
Right button
miss-function
Users press right button and will show
the result of pressing left button.
Digital mouse defect
Cursor Trembling
When digital pen tip closes to or
touches with tablet, the cursor is
trembling and can’t stop in the certain
point.
1. Low battery power,
voltage is not stable
2. If this condition is
happened in Win2K OS,
please check Control
Panel’s “Mouse” and
disable “accelerating
cursor moving function”
11
If users find the problem as above, we suggest that changing new one is the better
method.
3.6 Change Digital Mouse’s Battery
Digital mouse needs a 1.5V, AAA alkaline battery in using. The battery is set in the
bottom of mouse. For changing new battery of mouse, you shall turn over digital
mouse and you can see the battery cover. After taking apart the battery cover, the
battery can be taken away and change the new one.
Chapter 4. Important Notes
Note:
Most tablet problems are caused by the defects of PCB . If you want to replace
Tablet’s PCB , please note the PCB must be contacted tightly.
Note:
T
ablet can’t be placed near magnetic objects. It will influence the tablet
accuracy.
Note:
Please do not disassemble the digital pen by yourself.
Note:
Avoid water entering the tablet inside.
Note:
Don’t use the sharp part of pliers to hold the pen tip and pull it out.
12
Note:
Press the new pen tip forcibly into the pen.
Appendix – Part Lists
Part List
Item Component
No.
Standard
Number
Note
Cover Sheet
130-A2A7-510
1
Upper Case
15T-A200-519
1
LED light Cover
15T-A218-006
1
PCBA 02T-PF1209-101
1
USB Cable
737-5156-013
1
Pad 172-1030-030
4
Isolate Plastic
15T-A120-000
2
Screw 113-0308-010
6
Isolate Plastic
15T-A120-001
1
Digital Pen
01P-236L-510
1
Digital Mouse
O1M-10I4-516
1
Bottom Case
15T-A120-001
1
13