Full Text Searchable PDF User Manual
Service Manual G-Shot P510
Service Manual
G-Shot P510
Version K01A
Version: K01A
1
Service Manual G-Shot P510
Contents
………………………………...…………..2
1.Function Test ………………………………………3
2.Troubleshooting ……………………………………4
3.Disassemble Procedure ……………………………5
4.Firmware Update Procedure ………………….…..6
5.Parts List ……………………………………………7
6. Tools …..……………………………………………13
Version: K01A
2
Service Manual G-Shot P510
1. Function Test
TOOL/EQUIPMENT
SM card*2, TV, AC adapter*2, lens-wiping paper
USB cable, flower, accessory, computer
OPERATION DESCRIPTION
ITEM OPERATON
DESCRIPTION
1
Put the AA battery into the camera, press power key to power on, then
you enter an image as the one on the right side. Check whether the image
(Status Icon on LCD could not be covered or partly covered by the rear
cover) and the indication symbols are normal or not. (Trigger mode, the
quantity of captured images and the quality etc. )
2
Press Flash mode button and choose and mode respectively, then
shoot a picture with your hand covering the lens to see whether the flash
mode has triggered or not.
3
Turn the lens chamber to choose digital zooming mode, choose macro
shooting+ off flash mode, shoot one image of the flowers. When you
turn the lens chamber, check if it sways or emits any abnormal sound.
4
Turn the lens chamber to choose the digital zooming mode, choose
micro shooting + off-flash mode to shoot one image.
5
Press Self-timer button, choose the or self-timer mode, then
press Flash mode button to choose un-flash and shoot an image
towards bright spots.
6
Press Mode button, choose Movie mode, shoot 5 to 10 minutes
7
Press Mode button, change to Display mode, review the images shot
in the previous steps. Press the Still shutter button to review the movie,
check if it is abnormal.
8
Check all the functions including in the main menu and use the USB
cable to link the TV to see if it is normal. If everything is OK, delete all
the images have shot.
9
Power off, insert SD card, power on again, repeat step 3 to 8.
10
Press MODE and MENU buttons at the same time, to check FW version,
then press shutter button to reset camera, take out SD CARD and
batteries.
Version: K01A
3
Service Manual G-Shot P510
2. Troubleshooting
Item
NG point
NG Analyzing solution
Power on fail(without
current )
Changing the fuse on MCU PCB.
Power on fail(with
100uA current )
Changing the MCU PCB.
Power system
Power on fail, with
normal current
Changing the MCU PCB.
Power on ok with LCD
black /white images
Changing the LCD FPC.
RTC function no good Changing the MCU PCB.
Auto serial capture
after power on
Changing the MCU PCB & shutter board
Power on ok, after
capture, LED lamp
always blinking, then
camera shut down
SD card fail
１
.
SD card without
written protection
but with LCD
display the icon
２
.
after insert SD
card ,camera can’t
recognize it
Changing the SD card base pin.
LCD display ok, but
without TV display
Changing the MCU PCB.
Display system
USB no connection
Changing the MCU PCB.
Flash leakage
Changing the Flash tube.
No charging
Changing the flash PCB.
Charging and
triggering
system
With charging but
without triggering
Changing the flash PCB.
If change any PCB of DSC, the calibration is necessary.
Version: K01A
4
Service Manual
G-Shot P510
3. Disassemble Procedure
Step
Figure
Description
Remark
Tools
1
Finished Product
Examine if there's
any scratch on the
surface.
2
Remove all the screws
on the camera housing.
Do not scratch the
camera surface
while removing
the screws.
Screw driver
3
Remove the Front
Cover and Rear Cover.
4
Remove the Top Cover.
Unscrew the
screw behind the
capacitor first.
Screw driver
5
Remove the screws of
the Flash PCB.
Screw driver
6
Remove the screws of
the Main PCB
Screw driver
Disasse
mble
pr
oc
edur
es
Version: K01A
5
Service Manual G-Shot P510
4. Firmware Update Procedure
Product : G-Shot P 510
To update this camera firmware, you will need to have
1. The new firmware file.
2. One SD card.
3. One card reader.
Please follow the steps below to perform the update process:
1. Prepare a formatted and empty SD card.
2. Insert a SD card to the card reader. Copy the firmware file (ie xxx.bin) into the
SD card. Make sure the new firmware file is copied to the SD card.
3. Insert the SD card into the camera.
4. Plug in the AC adapter into the camera. The camera will then release 6
continuous beeps.
5. When hearing the “continuous beep” sound, Press shutter button once with the 6
continuous beeps. You will hear a single high frequency beep as you pressed the
shutter button and the continuous beep stops.
6. If the shutter button wasn’t push during the “ continuous beep”, please return to
step 4.
7. The LED will blink while updating firmware.
8. After 15 seconds, the camera will release another 6 beeps.
9. When the camera finishes beeps, power off the camera (remove the camera AC
adapter) and remove SD card.
10. Reformat the SD card if you want to use it again.
Note:
Don’t remove the power source during firmware update procedures.
Version check : Press and hold the shutter button then power on the camera.
Version: K01A
6
Service Manual G-Shot P510
5. Part List (G-Shot P510)
Item
Part Name
Part Number
1
Front Cover Assy
9H544-2000
2
Rear Cover Assy
9F644-3000
3
Battery Cover
9D134-460-98
4
USB Jack Cover
9D134-019*2BF
5
Flash PCB
9F647-4100
6
5 Way Buttons
9D234-005-3AG
1. Front Cover Assy
Version: K01A
7
Service Manual G-Shot P510
2. Rear Cover Assy
Version: K01A
8
Service Manual G-Shot P510
3. Battery Cover
Version: K01A
9
Service Manual G-Shot P510
4. USB Jack Cover
Version: K01A
10
Service Manual G-Shot P510
5. Flash PCB
Version: K01A
11
Service Manual G-Shot P510
6. 5 Way Button
Version: K01A
12
Service Manual G-Shot P510
6. Tooling
Item Description
Mark
1
Screw Driver (2.0m/m)
2 Tweezers
3 Soldering
iron
1. Screw Driver
Version: K01A
13
Service Manual G-Shot P510
2. Tweezers
Version: K01A
14
Service Manual G-Shot P510
Version: K01A
15
3. Soldering iron