Full Text Searchable PDF User Manual
Service Manual G-Shot P433
Service Manual
G-Shot P433
Version K01A
Version: K01A
1
Service Manual G-Shot P433
Contents
………………………………...…………..2
1.Function Test ………………………………………3
2.Troubleshooting ……………………………………4
3.Disassemble Procedure ……………………………5
4.Firmware Update Procedure ………………….…..6
5.Parts List …………………………………………11
6.Tools …..………………………………………….…15
Version: K01A
2
Service Manual G-Shot P433
1. Function Test
TOOL/EQUIPMENT
ESD protection glove, SD card, AA battery, flower, AC adaptor, TV
OPERATION DESCRIPTION
ITEM OPERATON
DESCRIPTION
1.
Check the open and close of battery cover, too tight or loosen is not allowed
2
Load in batteries according to the icon, power on camera, check the lens
extending status
3.
Press TELE key, power on camera, wait until initial image ending, then
loosen TELE key, to see if the FW version is for delivery one
4.
Re-power on camera, check if there is SD card icon on LCD display, then
take one picture in auto mode
5.
Check if the high/low light spots, black/white spots on LCD screen are
within the spec.
6.
Power off camera, check if the lens is going back
7.
Insert in 3.0V/2.0A AC adaptor, power on camera
8.
Dial the dial knob, check if in each mode, the LCD display is fit with mode
shifting process
9.
Shifting to manual mode, press flash mode shifting key to check if the flash
icon on LCD display is changing accordingly. Capture in force flash mode to
check if the strobe is flashing
10. Press “macro” mode key to check the icon displaying on LCD, and take one
picture, check the flash is not triggering
11. Press “self timer” key to check the icon displaying on LCD, and take one
picture to see if it is ok
12. Press “delete “key to delete all pictures
13. Enter into auto capture mode, press Menu key, choose “image size” to set
2048*1536,choose “fine”, then exit, press W/T key, take pictures.
14. Enter into manual capture mode, press Menu key, choose “image size” to set
2048*1536,choose “fine”, then exit, press W/T key, take pictures.
15. Enter into video mode, press shutter key, record for 3 seconds, then press
shutter key again to finish video.
16. Connect to TV, enter into “play back” mode, check if all the images and
video took just now is ok. Press “delete” key to format the storage.
17. Enter into “set up” mode, to reset camera to default values, make the dial
knob onto Auto mode
18
Power off camera, check the lens should going back totally, plug out AC
adaptor.
Version: K01A
3
Service Manual G-Shot P433
2. Troubleshooting
Item
NG point
NG Analyzing solution
No charging
Changing the MCU Board.
Charging and
triggering
system
No triggering
Changing the MCU Board.
Lens extending
/retracting is no good
Changing the MCU Board.
Lens system
Diaphragm changing
is no good
Changing the MCU Board.
Power on failure
(without current
response)
Changing the Power Board.
Power on fail (with
current)
Changing the Power Board.
Power and
System
AC power supplier
and battery changing
are no good
Changing the Power Board.
If change any PCB of DSC, the calibration is necessary.
Version: K01A
4
Service Manual
G-Shot P433
3. Disassemble Procedure
Step
Figure
Discription
Remark
Tools
1
Finished Product
Examine if there's
any scratch on the
surface.
2
Remove the all screws
at the camera housing
and remove the front,
rear cover.
Do not scratch the
camera surface
while removing
the screws.
Screw driver
3
Remove the screws to
take off the Switch FPC.
Screw driver
4
Desolder the joints of
Switch FPC.
Soldering iron
5
Disassemble the dial
mode and switch FPC.
Screw driver
6
Remove the screws to
take off the MCU PCB.
Screw driver
Disasse
mble
pr
oc
edur
es
Version: K01A
5
Service Manual G-Shot P433
4. Firmware Update Procedure
Product : G-Shot P433
To update this camera firmware, you will need to have
1. The new firmware file.
2. One SD card.
3. One card reader.
Please follow the steps below to perform the update process:
Version: K01A
6
Service Manual G-Shot P433
Version: K01A
7
Service Manual G-Shot P433
Version: K01A
8
Service Manual G-Shot P433
Version: K01A
9
Service Manual G-Shot P433
Note:
Don’t remove the power source during firmware update procedures.
Version: K01A
10
Service Manual G-Shot P433
5. Part List (G-Shot P433)
Item
Part Name
Part Number
Quantity
1
Front Cover Assy
9E944-1002
1
2
Rear Cover Assy
9E944-2015
1
3
Jack Cover
9E934-011*2DL
1
4
Dial mode
9E944-4002
1
5
MCU PCB
9E947-0100
1
6
Switch FPC
9E947-3100
1
7
Flash Tube Assy
9E947-4200
1
8
Screw 01635-348
7
1. Front Cover Assy
Version: K01A
11
Service Manual G-Shot P433
2. Rear Cover Assy
3. Jack Cover
Version: K01A
12
Service Manual G-Shot P433
4. Dial mode
5. MCU PCB
Version: K01A
13
Service Manual G-Shot P433
6. Switch FPC
7. Flash Tube Assy
Version: K01A
14
Service Manual G-Shot P433
6. Tooling
Item Description
Mark
1
Screw Driver (2.0m/m)
2 Soldering
iron
3 Tweezers
1. Screw Driver
Version: K01A
15
Service Manual G-Shot P433
Version: K01A
16
2. Soldering iron
3. Tweezers