Full Text Searchable PDF User Manual
Service Manual
GHT-511D HOME THEATER
Service Manual
Table of Contents
GHT-511D HOME THEATER .................................................................................................... 0
Chapter 1. INTRODUCTION........................................................................................................... 2
Function Block............................................................................................................................. 2
Chapter 2. Troubleshooting Guide.................................................................................................... 3
Chapter 3. Removal and Replacement.............................................................................................. 4
Disassemble & Assemble the Fuse .............................................................................................. 4
Disassemble & Assemble the Rear Cover.................................................................................... 5
Disassemble & Assemble Amplifier PCBA (SUB)...................................................................... 6
Disassemble & Assemble the Power Supply PCBA.................................................................... 7
Disassemble & Assemble the Decoder board .............................................................................. 9
Chapter 4. Testing Procedures ........................................................................................................ 10
Chapter 5. Important Notes............................................................................................................. 11
Packing requirement for sending the PCB assembly ................................................................. 11
Short of spare parts while repairing a speaker ........................................................................... 11
Chapter 6. Parts list (Vender’s number) .......................................................................................... 12
Chapter 7. Tools .............................................................................................................................. 13
Version 1.0
Page 1
Service Manual
Chapter 1. INTRODUCTION
Function Block
Signal input
Front speakers
Subwoofer
Center speaker
AMP PCBA
POWER
PCBA
Rear speakers
Transformer
Main board
Decoder
PCBA
Version 1.0
Page 2
Service Manual
Chapter 2. Troubleshooting Guide
Problems Condition
Probable
Reasons
Solutions
1.no power
1.power cable 1.cable broken
1.replace power cable
2.fuse
1.fuse broken
1.replace fuse
3.PCBA
1.center PCBA NG
1.replace center PCBA
2.power PCBA NG
1.replace power PCBA
3.Decoder PCBA NG
1.replace Decoder PCBA
2.display L.E.D. unlight 1.cover broken 1.L.E.D. broken or NG
1.replace L.E.D.
2.PCBA
1.Decoder PCBA NG
1.replace Decoder PCBA
2.cable broken
1.replace cable
3.button NG
1.button
1.button NG
1.replace button
2.PCBA
1.receiver NG
1.replace receiver
2.cable broken
1.replace cable
3.power PCBA NG
1.replace power PCBA
4.Decoder PCBA NG
1.replace Decoder PCBA
4.no sound
1.signal cable
1.signal cable NG
1.replace signal cable
2.PCBA
1.AMP PCBA NG
1.replace AMP PCBA
2.RCA socket NG
1.replace RCA socket
5.noise
1.speaker
1.speaker NG
1.replace speaker
2.PCBA
1.power PCBA NG
1.replace power PCBA
2.AMP PCBA NG
1.replace AMP PCBA
Version 1.0
Page 3
Service Manual
Chapter 3. Removal and Replacement
Disassemble & Assemble the Fuse
Step 1
Use a screwdriver to
turn counterclockwise
and open the fuse’s
cap.
Step 2
Get the Fuse and
replace it with the
same rate.
Step 3
To install the Fuse,
reverse the steps
shown above.
Fuse
Version 1.0
Page 4
Service Manual
Disassemble & Assemble the Rear Cover
Step 1
Using a screwdriver to loose 12 screws.
After taking all screws off, you can take up the Rear cover.
To install the rear cover, reverse the steps shown above.
C
L
K
D
E
F
G
B
A
H
J
I
Version 1.0
Page 5
Service Manual
Disassemble & Assemble Amplifier PCBA (SUB)
Step 1
*Disassemble the Rear Cover first.
Disconnect the cables & wires
*Mark the position of cables & wires
Step 2
To loose 2 screws.(A & B)
Step 3
To loose 2 screws. After taking all screws
off, you can take up the Amplifier PCBA
*To install the Amplifier PCBA, reverse
the steps shown above.
A
B
Version 1.0
Page 6
Service Manual
Disassemble & Assemble the Power Supply PCBA
Step 1
*Disassemble the Rear Cover
first.
Disconnect the cable.
Step 2
To loose 8 screws. Form A-H.
Step 3
To loose 4 screws. Form I-L.
Step 4
Unsolder the wires on Power
Supply PCBA. And remove the
wires.
*Mark the position of wires
Cable
G
H
E F
D
C
B
A
I
K
J
L
Version 1.0
Page 7
Service Manual
Step 5
Unsolder the wires on Power
Supply PCBA. And remove the
wires.
*Mark the position of wires
Step 6
Disconnect the 3 cables. *To
install the Power Supply PCBA,
reverse the steps shown above.
Red
Grey
White
Version 1.0
Page 8
Service Manual
Disassemble & Assemble the Decoder board
Step
1
Remove the main board.
Step
2
Use tweezers to remove the fixed
glue. And then use your hands to
separate decoder board from
main board.
*To install the decoder board,
reverse the steps shown above.
Version 1.0
Page 9
Service Manual
Chapter 4. Testing Procedures
Step 1
Connecting the GHT-511D to a DVD or VCD player. Play a DVD disk on it.
Step 2
Power on the GHT-511D. The monitor should display ‘321’ then ‘0db’.
LED display ‘C’, ’L’, ’C’, ’SUB’, ’LS’, ’RS’, ’Digital’, ’Coaxial’, ’Lock’.
Step 3
Press the volume +/- button if it changes the volume level of each channel.
Step 4
Press the volume +/- button. Set the volume level to 0db.Change input signal to
‘Line’. The monitor should display ‘0db’.LED display ’SUB’, ’Line’, ’St’.
The sound only comes from L , R , SUB channel.
Step 5
Press the Mode button. LED display ’PL’, ’R’, ’C’,’SUB’, ’LS’, ’RS’, ‘Prologic’,
‘Line’, ’Lock’.
The sound comes from 5.1 channel.
Step 6
Press the Input button. Change input signal to ‘Optical’. The monitor should
display ‘321’ then ‘0db’. LED display ’L’, ’R’, ’R’, ’C’,’SUB’, ’LS’, ’RS’,
‘Optical’, ’Lock’, ‘Digital’ .The sound comes from 5.1 channel.
Step 7
Press the mute button it makes the volume level of each channel to null. Press the
Mute button again .It backs to normal.
Version 1.0
Page 10
Service Manual
Chapter 5. Important Notes
Packing requirement for sending the PCB assembly
PCB assembly is a kind of sophisticated electronic circuit board. Therefore, well packing will
be required when sending them by post or courier.
1.
Some sophisticated IC components are mounted on the PCB assembly, hence it is
necessary to pack each PCB assembly with a separate static protecting beg, in order to
avoid static electricity.
2.
Reliable external packing is also very important when sending the PCB assembly by post,
in that it would avoid unnecessarily lost or damage.
Short of spare parts while repairing a speaker
If you are short of spare parts when you have some speakers waiting to be repaired, it would be
recommended to take the necessary parts from one speaker, so that you may have the as many
as speakers be repaired and sent back to your customer, and left only one or few speakers
waiting for spare parts sending from KYE.
Version 1.0
Page 11
Service Manual
Chapter 6. Parts list (Vender’s number)
Item Part
number
description
Position
1 J66-01236-000
PCBA
AMP
2 J66-01236-400
PCBA
CENTER
AMP
3 J66-01335-000
PCBA
POWER
4 J66-01335-010
PCBA
VOLUME
CONTROL
5
J83-005AA-U00
FUSE 125V/5A SLOW BLOW
6
J51-00002-03 NJM4558DD
7
J53-00001-02 Diode
1N4148
8
J51-01054-000 IC
TDA7296
60W
9
J52-21001-000 Resonator
4MHZ
10
J51-01011-000 IC
TL074/
11
J51-11018-000 IC
L7815
12
J51-11019-000 IC
L7915
13
J51-21006-010 IC
PT2258
14
J52-00027-01 Transistor
2SC1815
15
J52-31003-000 FET
2SJ111
16
J53-21009-000 Diode
KBU808
17
J51-11024-000 IC
L7805CV/ST
18
J51-21002-300 MPU
EM78P451P
19
J52-00026-02 Transistor
2SA1015
20
J66-01335-330 PCBA
DSP
Version 1.0
Page 12
Service Manual
Chapter 7. Tools
1.
VCD or DVD Player
2.
MUSIC CD or DVD
1. Soldering-Iron
(40W)
1. Tweezers
2. Screwdriver
3. Pliers
4. Multimeter
5. Glue-heater
Version 1.0
Page 13