Genius G24 Si User Manual

Download PDF User Manual

Full Text Searchable PDF User Manual

ENGLISH

Genius Car Alarm

www.geniuscaralarm.com

Genius Car Alarm

www.geniuscaralam.com 1

Car Alarm Series 2 B

4 Buttons

G24 Si

(Internal Shock Sensor)

Version 3

ENGLISH

Genius Car Alarm

www.geniuscaralarm.com

Genius Car Alarm

2 www.geniuscaralam.com

CAR ALARM GENIUS – Series 2B

4 Buttons - G24 Si

(Internal Shock Sensor)

•

Module controlled using Micro-Processor

•

2 Transmitters - 4 buttons with color Blue LED

•

4 Learning Transmitters (Codes)

•

Transmission frequency 370 MHz (Anti-Scanner)

•

Panic by transmitter

•

Car Finder by transmitter

•

Transmitter Arm and Disarm Mute

•

Programmable Mute Armed and Disarmed

•

Negative output Channel 2 (Opens electric trunk)

•

Negative output Channel 3 optional modules (Programmable)

•

Opening the electric trunk without deactivating the alarm using the transmitter

(channel 2)

•

LED indicator on the board

•

Programmed controls identifier (P.C.I.) (Programmable)

•

1 Positive output for Light flash with internal relay in the module

•

Central Door Lock on Negative

•

Automatic Armed (Programmable)

•

Electric locks on with the Automatic Armed (Programmable)

•

Ignition Lock and unlock (Programmable)

•

Double push button to unlock door

•

Automatic Rearm (accidental disarm)

•

Automatic Rearm with Lock

•

Shock Sensor bypass by transmitter

•

Line door pin switches (Positive or Negative)

•

Line hood and trunk pin switches (Negative)

•

Electronic siren of 120 dba

•

Mode Valet (using emergency button or Transmitters )

•

Wires identified by colors

•

Protection fuses included in the installation harness

•

Transmitter Anti-carjack (Programmable)

•

Door Anti-carjack (Optional)

•

Ignition Anti-carjack (Programmable)

•

Presence Anti-carjack (Additional transmitter) (Programmable)

•

Warning Light when anti-carjack activates

•

Acoustic warning when anti-carjack activates (Programmable)

•

Negative output in armed, for engine cut

•

Second engine cut (Programmable)

•

Negative output timed for windows-up modules (Programmable)

•

Defective zone exclusion

•

Flashing output for the horn (Programmable)

•

Dome Light (Programmable)

•

Function programming through software

•

Manual disarmed by safety PIN code (Programmable)

•

Memory of last status of the system.

ENGLISH

Genius Car Alarm

www.geniuscaralarm.com

Genius Car Alarm

www.geniuscaralam.com 3

Introduction

Thank you for purchasing our security system for your vehicle. Read well the user’s

manual of the system specifically the functions of the transmitter, the valet switch and the

LED indicator on the board.

The Transmitter

Each transmitter has a different code, the alarm system is programmed by the factory with

2 codes (2 transmitters), and you can program a maximum of 4 codes (4 transmitters). The

transmitter has 4 buttons, I, II, III, IV.

The system is pre-programmed with a work routine with each button of the transmitter.

It works with the following configuration:

Programming and memory of the transmitters and witnessed transmitters

The alarm system is designed to memorize up to 4 different transmitters, be careful when

programming a transmitter, the alarm system deletes from the memory the previous

transmitters, program all transmitters at the same time, since through this deletion function

you can delete the memory of any transmitter if it is lost by simply programming the

transmitter or transmitters again. The witnessed transmitter should be the last one to be

memorized.

To enter the memory and be able to program the transmitters, follow these steps:

1. Set the ignition switch in ON

2. Within the first 5 seconds after setting the ignition switch in ON, press and let go the

reset button 5 times, the siren will confirm with long sound, you have 10 seconds to

enter the transmitters, if you do not enter any transmitter before the 10 seconds or

set the ignition switch in OFF, the system will automatically exit the transmitter

learning mode and the siren will confirm with 2 sounds and the memory of the

transmitters will not be deleted.

3. Press and let go button I on the transmitter to program, the siren will confirm with 1

sound the memorization of the transmitter, as of that moment the old transmitters

will be deleted.

Button I

Button III

Button IV

Button II

ENGLISH

Genius Car Alarm

www.geniuscaralarm.com

Genius Car Alarm

4 www.geniuscaralam.com

4. If you wish to program a second transmitter, repeat step 3 where the siren confirms

with 2 sounds the memorization of the second transmitter and with 3 sounds the

third and with 4 the programming ends.

The system pre-programmed with a routine of work with each button of the Transmitter. It works

with the following configuration:

a. Alarm is armed and the doors

are locked

a. IGNITION IS

OFF

Press

button 1

once

b. Stop temporarily the alarm’s

trigger

b. SIREN

SOUNDING

Press

button 1

, then

button

within 2 seconds

Arm the alarm cancelling the

shock sensor.

IGNITION IS OFF

Press

button 1,

then

button

within 2 seconds

Arm the alarm cancelling the

shock sensor and the doors’

signal input

IGNITION IS OFF

Disarm and unlock doors

ARMED

Press

button 2

once

Stop temporarily the alarm’s

trigger.

SIREN

SOUNDING

Press

button 4

for 3 seconds Channel 2 (Open Trunk)

IGNITION IS OFF

Press

button

for 1 second

Car Finder.

ARMED

Press

button 3

for 3 seconds Panic

IGNITION IS OFF

Press

buttons 1

and

together for 3 seconds

Anti-hijacking

IGNITION IS ON

Press

button 3

, then

button

within 2 seconds.

Silent Arming Mode

IGNITION IS OFF

Press

button 3

, then

button

within 2 seconds.

Silent Disarming Mode

ARMED

Press

button

, then

button

for 3 seconds.

Valet Mode

IGNITION IS OFF

Press

buttons 3

and

together for 2 seconds.

Arm Channel 3

IGNITION IS

ON/OFF

ENGLISH

Genius Car Alarm

www.geniuscaralarm.com

Genius Car Alarm

www.geniuscaralam.com 5

Alarm system armed.

The alarm system can be armed in 2 methods.

1. The first, using button I on the transmitter. It is necessary for the ignition switch to

be OFF and for the system not to be on Valet.

The second, using the automatic armed, which is obtained when the ignition switch

goes from ON to OFF and then open and close a door. The system will

automatically arm in 30 seconds after closing the last door, this functions is

programmable (see function programming chart).

Alarm system armed by using the Transmitter.

The alarm system will always be armed by using the transmitter, provided that the ignition

switch is OFF and the system in not in the Valet mode.

To arm the alarm system after leaving the vehicle and closing all the doors, simply press

and let go button I on the transmitter once, the lights will flash once, the siren will sound

once and the LED indicator on the board will start flashing slowly to confirm that the

system in armed. If the electric locks are connected to the alarm system, they will be

locked; the current breaker will be activated avoiding the use of the vehicle, after 3

seconds the system goes to expecting-robbery mode

Exclusion of defective zones

When the alarm system is armed and if any of the zones is defective, the siren shall sound

3 times and, simultaneously, the lights will flash 3 times, indicating that a zone is defective,

when this occurs, the defective zone will be automatically excluded and the vehicle will be

protected on the rest of the zones. For example, if the trunk is not closed properly alter

arming the alarm system using the transmitter, the siren will sound 3 times and the lights

will flash 3 times indicating a door is not properly closed and it will exclude the sensors of

that zone. The defective zone will be included again in the protection 3 seconds after

correcting the failure, alter properly closing the trunk.

Armed and activated alarm system

When the alarm system is armed, the LED indicator on the board blinks slowly, if a door is

opened, the siren starts sounding and the lights flashing for 60 seconds, if the door

remains open after the 60 seconds, the siren will keep sounding and the lights flashing for

3 minutes, after the 3 minutes, the alarm system excludes the door sensors protecting the

vehicle through the rest of the sensors, if the door is closed before the first 60 seconds

after the siren start sounding, the same will silent after 60 seconds and the light will stop

flashing.

If when the alarm system disarms the siren sounds 4 times and the lights flashes 4 times,

this indicates the vehicle was victim of a carjack attempt. The LED indicator on the board

will continue to blink until the ignition switch is ON. Please check the vehicle.

Alarm System Disarm

When the alarm system is armed, press and let go button No. II on the transmitter, the

siren will sound twice and the lights will flash twice indicating the alarm system disarmed,

the current breaker will deactivate, the LED indicator on the board will turn off, if the

electric locks are connected, they will open, if button II is pressed again, the system will

send the second pulse to open the electric locks

Silent Arm

First press and let go button III and then press and let go button I on the transmitter to arm

the alarm system silently, the alarm system will arm without the sound of the siren. When

the alarm is silently armed and a door is open or not properly closed, the siren will sound 3

times as an alert warning.

ENGLISH

Genius Car Alarm

www.geniuscaralarm.com

Genius Car Alarm

6 www.geniuscaralam.com

Silent Disarm

First press and let go button III and then press and let go button II on the transmitter to

disarm the alarm system silently, the system will disarm without the sound of the siren.

When silently disarmed and after the vehicle has been victim of a carjack attempt, the

siren will sound 3 times as an alert warning.

ARMING WITH ZONES’ CANCELLATION

This system allows us to arm the alarm cancelling the shock sensor as the 1

zone and

the shock sensor and doors’ signal as the 2

zone. This is to avoid false alarm when the

shock sensor or the doors’ switch is triggered.

1. Press

button 1

, then press

button 3

within two seconds, the shock sensor is cancelled.

2. Press

button 1

, then press

button 2

within 2 seconds, both the shock sensor and the

door’s signal are cancelled.

DOORS’ SIGNAL ARMING DELAY

This function allows us to arm the alarm even when the dome lights are on, because the

system will not recognize this signal for the programmed time, avoiding notices of open

door when the alarm is armed.

* See Programming Table-

Disarm of the system using the reset button

In case you lose the transmitter, damage it or the battery of the same dies,

you can disarm the system by pressing the reset button.

First, with the security system armed, open the driver’s door and the siren will

start sounding.

Second, turn ON the ignition switch, before the 10 seconds press the reset

button the number of times assigned in the security code (1 as set by the

factory) the siren will continue to sound for 3 seconds and if the security code

is right the system will disarm.

PANIC

With this function, we can make the system to trigger intentionally to prevent or attract the

attention of people, in case of a theft or aggression attempt.

a. With the ignition in OFF,

- PANIC,

BUTTON 3

FOR 3 SECONDS

b. The siren and the lights will trigger for 3 seconds.

c. Press

button 1

button

to stop PANIC, the system will remain armed.

d. With the ignition in

ON.

Activate PANIC.

By stopping PANIC, the system will remain armed without the ignition interrupter, but if the

ignition key is turned to OFF position, the IGNITION INTERRUPTER will be activated.

CAR FINDER

With this function we can make the system to send us signals with the siren and lights,

which will serve us to locate the vehicle, whenever we are in the transmission range

between the remote control and the vehicle.

a. When the alarm is armed,

- CAR FINDER,

BUTTON

1 FOR 1 SECOND

b. The siren will chirp 10 times and the parking lights will flash 10 times.

c. Press

button 1

button 2

to stop the Car Finder.

ENGLISH

Genius Car Alarm

www.geniuscaralarm.com

Genius Car Alarm

www.geniuscaralam.com 7

DUAL-STAGE SHOCK SENSOR

If the vehicle receives a

light impact

, the siren will chirp and the lights will flash 5 times

each. If the vehicle receives a strong impact, the siren and the lights will trigger for 30

seconds.

*The sensitivity can be adjusted.

ANTI-HIJACKING BY IGNITION (Programmable by Jumper)

This function is in the memory’s software to activate automatically the anti-hijacking mode

every time the ignition key is turned form OFF position to ON position. (See Jumpers table)

ANTI-HIJACKING BY TRANSMITTER (Programmable)

This function is used to immobilize the vehicle in case of emergency, pressing the buttons

1 and 2 simultaneously for 3 seconds and the anti-hijacking mode will activated by

transmitter. (See Functions Programming Table)

ANTI-HIJACKING BY DOORS (Programmable)

With the ignition key in ON position, open driver’s door and the anti-hijacking mode by door

will be activated. You must connect the wire of anti-hijacking by door. (See Functions

Programming Table)

WITNESSED ANTI-CARJACK (Additional transmitter necessary)

This function is used to immobilize the vehicle in case of emergency by

simply separating the additional transmitter while the engine of the

vehicle is working, 60 seconds after the signal disappears, the lights will

flash twice, The LED indicator will start blinking indicating

the anti-carjack has been activated, if the acoustic warning is

programmed, the siren will sound twice.

This function is programmable (see function programming chart).

For the witnessed anti-carjack to function, the additional transmitter must

be acquired. It must be programmed in the alarm system memory and

enable function in the function chart.
Turning on the transmitter
Press the button on the transmitter and hold it, the LED indicator on the

transmitter will turn on and off, after 3 seconds the LED on the transmitter will turn on for 2

seconds. Let go the button on the transmitter.
The transmitter will send a signal to the receiving module (Central Unit) every 6 seconds.
When the internal battery of the transmitter is dead, the LED transmitter will warn you by

continuously blinking. You must replace the batteries of the transmitter.
Turning off the transmitter
Press the button on the transmitter and hold it, the red LED on the transmitter will flash

once, after 3 seconds, the LED of the transmitter will flash 5 times. Let go the button of the

transmitter.

ANTI-HIJACKING SEQUENCE

When the system enters in anti-hijacking mode,

0 to 15 seconds

, nothing happens (See Functions Programming Table, function 9).

Optional

witnessed

transmitter

ENGLISH

Genius Car Alarm

www.geniuscaralarm.com

Genius Car Alarm

8 www.geniuscaralam.com

16 to 30 seconds

, the LED twinkles slowly.

31 to 45 seconds

, the LED will flash rapidly, the siren will chirp once every two

seconds and the lights will flash once every second.

46 to 70 seconds

, the LED will flash rapidly, the siren will chirp once every second

and the lights will flash once every second.

After 70 seconds

, the siren and the lights will trigger, the engine interrupter will be

activated.

b. When the anti-hijacking is triggered, (the ignition remains in ON position). Even if the

ignition key is turned to OFF position, the siren and the lights remain triggered for 3

minutes.

c. If the ignition key is turned to ON position again, the siren and the lights will be

triggered again.

*To exit Anti-hijacking mode:

APPLY THE DISARMING EMERGENCY PROCEDURE

AUTOMATIC ARMING

This function provides us with a greater confidence in our alarm, giving us security and

tranquility because of the alarm’s complete protection.

With this function we can assure that the system will arm automatically in case we forget to

do so.

* For more security, it is recommended to arm the system with the remote control.

a. After turning the ignition key to ON position and closing the doors, 30 seconds later the

alarm will be automatically armed.

* See

Jumper 1

selection for MANUAL / AUTOMATIC Arming

* See Programming Table for Automatic Arming Programming with doors lock.

AUTOMATIC REARMING

When the alarm is disarmed with the remote control, without turning the ignition key to ON

position and without opening the doors, 30 seconds later the alarm will be re-armed and

the doors will be locked.

CHANNEL 2 (TRUNK)

a. When the alarm is disarmed:

CHANNEL 2,

BUTTON 4

FOR 3 SECONDS, the signal is triggered (The trunk will be

opened)

b. When the alarm is armed:

Activating channel 2, first the alarm will be disarmed and then the signal is triggered. (The

trunk will be opened)

* See Programming Table

CHANNEL 3

With this signal we can control a function (connecting an additional- optional module) such

as a window module, or the engine ignition.

Press buttons

and

together for two seconds to activate the function. (If the buttons are

pressed for more time, the signal is applied; releasing the buttons will stop the signal)

* See Programming Table

SECOND PULSE TO UNLOCK DOORS

If we wish to control the doors lock as AGENCY TYPE, with this function we can do it.

Disarming the alarm pressing the

Button 2

once, only the driver’s door will be unlocked. If

we press

Button 2

again, within three seconds the others will be unlocked.

*See Programming Table

ENGLISH

Genius Car Alarm

www.geniuscaralarm.com

Genius Car Alarm

www.geniuscaralam.com 9

HORN OUTPUT

Normally, in alarms the sound is produced by a siren (Positive Output), with this new

system, we can simultaneously drive the horn’s sound (Negative Output), or select one of

the two functions.

See programming Table

VALET MODE

Valet, it is the function that allows us to cancel temporarily our security system, for those

situations in which we do not want to use the alarm system, for example in the car washer,

while in maintenance services, etc.

Valet by Remote Control

a. While the alarm is disarmed, press

BUTTON 4

once. Within 3 seconds, press

BUTTON 3

for 2 seconds.

b. The LED will light solid and the siren will chirp 5 times, confirming that the system is

in Valet mode.

c. If the system is in Valet mode: If we press

BUTTON 1,

the doors will be locked and

the lights will flash once if

BUTTON 2

is pressed, the doors will be unlocked and the

lights will flash twice. d. To exit Valet mode, apply the previous mentioned procedure.

*The LED will turn off.

Valet by Reset Switch.

a. When the ignition key is in ON position, keep pressing reset switch until the siren

chirp 5 times.

b. The LED will light solid confirming that the system is in Valet mode.

c. To exit Valet mode, apply the previous mentioned procedure.

* The LED will turn off.

DOORS LOCK WITH IGNITION

The overall alarm system offers us a comfortable and secure operation, and this function is

one of them.

a. After the engine ignition is on, the doors will be locked 2 seconds later.

b. Once the engine is turned off, the doors will be unlocked immediately.

DOOR

LOCKS’

CONTROL

WITH THE TRANSMITTER

WHILE DRIVING

While driving, if we press

button 1,

the doors will be locked; and if we press

button 2

, the

doors will be unlocked.

FUNCTIONS’ SELECTION

- JUMPERS

Important: All the Jumper’s selections have to be determined before installation.

JUMPER

MODE

DEFAULT FABRIC

CONFIGURATION

MODE

VARIANTS

J1: AUTOMATIC ARMING /

MANUAL ARMING

AUTOMATIC ARMING

MANUAL ARMING

J2: DOOR LOCKS’ TIME

0.5 SECONDS

DOUBLE PULSE

ENGLISH

Genius Car Alarm

www.geniuscaralarm.com

Genius Car Alarm

10 www.geniuscaralam.com

J3: DOORS’ POLARITY

(+ O -)

DOORS’ INPUT (-)

DOOR’S INPUT (+)

J4: ANTI-HIJACKING BY

IGNITION

ACTIVATED

(ON)

DEACTIVATED

(OFF)

INSTRUCTIONS

* LED’S

CONDITIONS

a. Armed Alarm: The LED will flash slowly (once every second)

b. Automatic Arming and Re-arming: The LED will flash rapidly.

c. Valet Mode: LED will light solid.

TRIGGER DIAGNOSIS

– LED

Disarming the alarm after it was triggered will make the LED to flash, indicating us the

zone that triggered the alarm.

Triggered by Ignition ---------------------------The LED will flash once.

Triggered by Opened Door ---------------------The LED will flash 3 times.

Triggered by Shock Sensor----------------------The LED will flash 4 times.

FUNCTIONS PROGRAMMING

a. Turn the ignition key to ON position.

b. Within 10 seconds, press the valet switch

times.

c. The siren will chirp 3 times.

d. Press the valet switch the number of times of the selected function.

* The siren will sound every time the valet switch is pressed.

e. Press the

button

in the remote control of the selected option.

* If the

button 1

is pressed, the siren will chirp once (1); if the

button 2

is pressed, it

will chirp twice (2), and three chirps if

button 3

is pressed.

f. To exit the programming mode, turn the ignition key to OFF position.

* The siren will sound a (1) long beep.

PROGRAMMING TABLE

Times the

Valet

switch is

pressed

FUNCTION

Press button 1

Press

button 2

Press

button 3

Lock closure with automatic arm

YES

Door’s Signal Activation Delay

WITHOUT

DELAY

Delay of 30

seconds

Delay of 60

seconds

Anti-hijacking by transmitter

YES

Lock Doors with Ignition

YES

Unlock Doors with Ignition

YES

ENGLISH

Genius Car Alarm

www.geniuscaralarm.com

Genius Car Alarm

www.geniuscaralam.com 11

OUTPUTS FOR CHANNEL 3

Second Pulse to

Unlock Doors

CHANNEL 3

HORN

OUTPUT

(

Anti-hijacking Warning

*Indicates the beginning of the

sequence

YES

ARMED and DISARMED Notices

YES

Reminder to arm the alarm.

*Only in Manual Arming

YES

Opened Door Warning

YES

Channel 2

Electric Trunk

Dome Light

30 second

Electric

window

lifter

Anti-hijacking by Door

Close Door

Opend Door

FABRIC RESET

Witnessed Anti-carjack

(Additional Transmitter)

OFF

Programmed controls identifier

(P.C.I.)

OFF

* Example to do the Programming:

a. Select the functions to be changed. (It is recommended to write down them to avoid

mistakes)

b. If you are going to work with 2 or 3 functions, follow these steps:

c. Function # 2: Press valet switch twice and then select

button 1

d. Then, if you wish to program, function #4, press twice again the valet switch (to

complete the # 4) then select

button 2

of the remote control.

e. And then, if you also want to program function # 8, press four times the valet switch (to

complete the # 8), select the

button 2

of the remote control.

IMPORTANT: Going from one function to another, just press the valet switch the

number of times necessary to complete the following function.

DETAILS OF THE PROGRAMMING FUNCTIONS

1. LOCK CLOSURE WITH AUTOMATIC ARM

If we programmed the Automatic Arming function (JUMPER 1), the alarm will arm by itself,

so with this function 1 we can choose to unlock or lock the doors.

2. DOORS’ SIGNAL ARMING DELAY

This function allows us to arm the alarm even when the dome lights are on, because the

system will not recognize this signal for the programmed time, avoiding notices of open

door when the alarm is armed.

ENGLISH

Genius Car Alarm

www.geniuscaralarm.com

Genius Car Alarm

12 www.geniuscaralam.com

3. ANTI-HIJACKING BY TRANSMITTER

This function is used to immobilize the vehicle in case of emergency; pressing the buttons

1 and 2 simultaneously for 3 seconds while the engine is running, the siren will chirp once

and the parking lights will flash once; after 15 seconds, the LED will start to twinkle

indicating the activation of the anti-hijacking mode. This function is programmable (See

Functions Programming Table)

4 and 5 DOORS LOCK WITH IGNITION

This function provides us comfort and security. When the engine is turned on, the doors

will

lock

TWO seconds later. When the engine is turned off, the doors will unlock

immediately.

6. OUTPUTS FOR CHANNEL 3

Select a function from one of these three options:

1. CHANNEL 3- Output to drive an optional function, such as a windows module.

2. SECOND PULSE TO UNLOCK DOORS

3. HORN OUTPUT-

NEGATIVE OUTPUT *

7. ANTI-HIJACKING WARNING:

BEGINNING OF THE SEQUENCE

When this function is activated, triggering the anti-hijacking will make the siren chirp once.

8. ARMING OR DISARMING WARNINGS

When arming the alarm, the siren will chirp once; when disarming the alarm, the siren will

chirp three times. Sometimes, the chirps may be annoying, so the system gives us the

option to cancel temporarily these warning sounds.

9. REMINDER TO ARM THE ALARM

When we get off the vehicle and close the last door,

seconds later the siren will chirp

three times and

seconds later other three chirps will be produced, indicating that we

have not armed the alarm.

* This function will only activate if in MANUAL ARMING MODE

* See Programming Table

10. OPENED DOOR WARNING

While driving, if one of the doors is opened, the lights will flash for 60 seconds. In case the

door keeps open and is closed before the 60 seconds, the lights will turn off.

11. CHANNEL 2

Function’s Selection- Trunk’s release or dome lights:

DOME LIGHTS – Negative Output Signal for 20 seconds. When disarming, if the ignition

key turns to ON, the dome lights turn off.

TRIGGERED, the dome lights are intermittent.

12.

ANTI-HIJACKING BY DOOR (Open / Close)

With the ignition key in ON position, open or close the driver’s door, the siren will sound

once and the parking lights will flash once indicating the activation of the anti-hijacking

mode. For the anti-hijacking by door to work, you must connect the anti-hijacking by door

wire to the push-button (-) in the driver’s door.

ENGLISH

Genius Car Alarm

www.geniuscaralarm.com

Genius Car Alarm

www.geniuscaralam.com 13

13. FABRIC DEFAULT RESET

This function allows us to correct the errors, if we mistaken during programming.

14. WITNESSED ANTI-CARJACK (ADDITIONAL TRANSMITTER NECESSARY)

This function is used to immobilize the vehicle in case of emergency by simply separating

the additional transmitter while the engine of the vehicle is working

15. PROGRAMMED CONTROLS IDENTIFIER (P.C.I.)

Every time you set the key in ON, the LED will light immediately for 10 seconds, to indicate

the number of remote controls that were programmed.

1. Intermittency /pause = 1 control programmed

2. Intermittency /pause = 2 controls programmed

3. Intermittency /pause = 3 controls programmed

4. Intermittency /pause = 4 controls programmed

ENGLISH

Genius Car Alarm

www.geniuscaralarm.com

Genius Car Alarm

14 www.geniuscaralam.com

ENGLISH

Genius Car Alarm

www.geniuscaralarm.com

Genius Car Alarm

www.geniuscaralam.com 15

Purchase Date: ___________________________ Invoice _____________________

BENEFICIARY

Name: __________________________________

C.I.:_________________________

Vehicle’s Trademark: _______________________ Color: ___________________

Model: ____________________________ Vehicle’s Plate:

___________________________

STAMP AND SIGNATURE OF THE DISTRIBUTOR THAT INSTALLED THE SYSTEM

TECHNICAL REVISION

Date ___________________________________________________________

Observations____________________________________________________

Stamp: __________________________________________________________

Date ____________________________________________________________

Observations ____________________________________________________

Stamp: __________________________________________________________

Date_____________________________________________________________

Observations ___________________________________________________

Stamp _________________________________________________________

ENGLISH

Genius Car Alarm

www.geniuscaralarm.com

Genius Car Alarm

16 www.geniuscaralam.com

LIMITED WARRANTY

Every GENIUS branded alarm system is guaranteed for ( ) year(s) since the installation

date considering the following conditions:

1. This warranty does not cover damage or malfunctions caused by:

a. Immersion in water or liquids

b. Shocks or fire

Attempted modification or repair by unskilled hands

d. Controls’ Loss or Degradation

2. The costs of dismantling, assembling or any other will be borne by the claimant.

3. The implementation of this guarantee will have greater flexibility in its dealings, if the

user has placed the sticker on the rear window of the vehicle.

4. The technical department of the company reserves the right to determine the validity

of the guarantee according to expertise.

WARNING: The Anti-hijacking is exclusively a deterrent against possible theft. In no case

it can be considered as an insurance against theft. The manufacturer disclaims all liability

for damage or abnormal functioning of the alarm, accessories and automotive group, due

to improper installation or monitoring of the characteristics listed.

Recommendations for Storage

Take it with you always

1. Anti-hijacking Disarming

With the ignition key in ON position, press the reset button 1 time, wait 3 seconds and the

anti-hijacking mode will be disarmed.

Manual Disarming

Turn the ignition key to ON position, press the reset button 1 time, wait 3 seconds and the

alarm’s system will be disarmed.

3. Enter and Exit Valet Mode

With the ignition key in ON position, press and hold reset button for 5 seconds, the LED will

light solid; to exit Valet mode, with the ignition key in ON position, press and release reset

button, the LED will turn off.

Important

: Plastic and store these instructions and take it with you always.

Technical Specification

(1) Frequency

370 MHz

(2) Working Voltage

|From 9.5V to

16V

(3) Standby Current for ARM Mode

13mA

(4) Standby Current for DISARM Mode

11mA

(5) Maximum Parking Light Output

15A

(6) Maximum Negative Output for Trunk, Dome Light, 3

Channel

Negative 0.5A

(7) Maximum Central Door Lock Output

Negative 0.5A

(8) Combination of Fixed code in Transmitter

1,0480576

Ask a Question ?

PDF User Manual

G24AU1B

Full Text Searchable PDF User Manual