Full Text Searchable PDF User Manual
For 7’ 6” Doors. Extension Kit is available for 8’ Doors
Included Wall Console MUST be installed prior to Operation
of this Garage Door Opener.
Safe-T-Beam® Safety Reverse System MUST be Installed and
the Force Controls MUST be Properly set to close door.
This Equipment meets or exceeds all Federal, State and UL 325
Safety Requirements.
Will not operate “twice as fast” on one-piece doors.
SA
VE
TH
IS
M
AN
UA
L F
OR
FUTURE
REFERENCE
C
omplete
with
iNtelliCoDe®
R
emote
C
oNtRol
aND
SeRieS ii
e
leCtRoNiCS
Having Difficulty? Need Help?
Please call us: 1-800-35-GENIE (354-3643)
www.geniecompany.com
Please have Model information ready when calling
.
Warranty Information . . . . . . . . . . . . . . . . . . . 2
Safety Information . . . . . . . . . . . . . . . . . . . . . . 3
Important Installation Instructions . . . . . . . 3
Safety Features . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pre-installation Checklist . . . . . . . . . . . . . . 4-6
Control Adjustments . . . . . . . . . . . . . . . . . . 7-8
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Troubleshooting Guide . . . . . . . . . . . . 11-13
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . 14
Parts Lists / Exploded Views . . . . . . . . .15-16
Accessory Order Form . . . . . . . . . . . . . . . . . . 17
t
able
of
C
oNteNtS
3630436275
®
DC POWERED
SCREW DRIVE
OPENER
Operation and
Maintenance Manual
2
For Help, call 1-800-35-GENIE or visit www.geniecompany.com
* Model Number and Serial Number are located on
Motor Cover inside the lens .
See Power Head Assembly Exploded View on page 15
IT IS CRITICAL THAT ALL SAFETY WARNINGS
MARKED CLEARLY IN BOTH THE MANUAL
AND POSTER ARE READ, UNDERSTOOD AND
FOLLOWED.
t
he
G
eNie
C
ompaNy
l
imiteD
w
aRRaNty
What is covered?
Any defect in material and product workmanship from personal, normal house-
hold use in accordance with the Owner’s Manual .
For how long?
MODEL H8000-07 . . . Lifetime* on motor and 5 years all other parts .
*Lifetime = For as long as you own your home .
Who gets the warranty?
This warranty is limited to the consumer who originally purchased
the product .
Geographic scope:
This warranty applies only to units installed and operated within the country
where they were purchased .
Limitations:
IMPLIED WARRANTIES, I N CLUDING THOSE OF FITNESS FOR A PAR TICULAR
PURPOSE AND MERCHANT ABILITY (AN UNWRITTEN WARRANTY THAT THE
PRODUCT IS FIT FOR ORDINARY USE), ARE LIMITED TO ONE YEAR FROM THE
DATE OF PURCHASE . GENIE WILL NOT PAY FOR: LOSS OF TIME;
INCONVENIENCE; LOSS OF USE OF YOUR GENIE PRODUCT OR PROPERTY
DAMAGE CAUSED BY YOUR GENIE PRODUCT OR ITS FAILURE TO WORK; ANY
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES; OR ANY DAMAGES
RESULTING FROM MISUSE OR MODIFICATION OF YOUR GENIE PRODUCT .
Some states and provinces do not allow limitations on how long an implied
warranty lasts or the exclusion of incidental or consequential damages, so the
above limitations or exclusions may not apply to you .
This warranty is the only one we will give on your Genie product, and it sets
forth all our responsibilities regarding your Genie product . There are no other
express warranties .
State and province rights: This warranty gives you specific legal rights, and
you may also have other rights which vary from state to state and province to
province .
How to get warranty service:
To obtain warranty service for your Genie product, you must provide proof of
the date and place of purchase of the product .
1. Do-It-Yourself-Service
.
Call the Genie Customer Service toll free at 1 .800 .354 .3643 to speak in
person to a trained Genie representative for assistance in diagnosing the
problem and arranging to supply you with the required parts for do-it-
yourself repairs . Trained service representatives are available Monday-Friday,
8:00 a .m . - 9:00 p .m ., Eastern Time, and on Saturday, 10:00 a .m . to 7:00 p .m .,
Eastern Time (subject to holidays) You may also get the information you
need at
www.geniecompany.com
.
2. Service From Authorized Dealers
.
You also may obtain warranty service from Genie authorized dealers by calling the
Genie Customer Service at 1 .800 .354 .3643 or by visiting
www.geniecompany.com
before scheduling warranty service . If warranty service is provided by an authorized
dealer, Genie will provide all required parts under war ranty at no charge to you, but
the dealers are independent business people and may render a bench or ser vice call
charge for their services . Genie will not reimburse you or other wise be responsible for
those charges .
We suggest that you retain your original packing material in the event we choose
to repair or replace your Genie Product and request that you ship it to us . Be sure to
include your name, address, telephone number, proof of date and place of purchase
and a description of the operating problem . After repairing or replacing, your Genie
product, we will ship it to your home at no cost to you for parts and labor, but you will
have to pay a minimum of $5 .00 for shipping and handling charges .
Your choice of either one of the above-described service options is your exclusive
remedy under this warranty .
What this warranty does not cover:
This warranty does not cover batteries (which are considered replaceable parts),
installation, commercial use, defects resulting from accidents, damage while in transit
to our service location or damage resulting from alterations, misuse or abuse, lack of
proper maintenance, unauthorized repair or modification of the product, affixing of
any attachment not provided with the product, programming of the Remote Control
Devices, Safe-T-Beam® adjustment/cleaning, staples through wiring, pinched or broken
wires, Carriage disengaged, Force Control adjustments, door out of balance, broken
springs or cables, power outages, use of extension cords, missing or damaged parts on
discounted, clearanced, final sale or taped cartons, phantom operations (labor is not
covered if Opener is functioning properly while technician is in garage),fire, flood, or
acts of God, or other failure to follow the Owner’s Manual .
SAVE THESE INSTRUCTIONS
Visit Our Website at:
www.geniecompany.com
FOR ANSWERS: CALL 1.800.354.3643
Please note the following information,so it is available if you
need to call us.
Date Purchased
__________/_________/__________
Serial Number*
______________________________
Operator Model*
______________________________
Dealer Name
______________________________
Dealer Address
______________________________
City
______________________________
State / Zip
______________________________
NOTE
Please keep original or photocopy of your sales receipt
with this manual for future reference should service
ever be required.
INCLUDED IN THIS PACKAGE
Manual 1) Warranty Information
2) Pre Installation Checklist to be reviewed
prior to any assembly or installation
3) Necessary Adjustments
4) Programming Remote Devices
5) Maintenance and Troubleshooting
6) Parts Explosions
7) Accessory Order Form
8) Door Opener Association Safety and
Maintenance Brochure (DASMA)
9) Entrapment Warning Label - To be Adhered
in close proximity to wall control
Poster 1) Pictorial and step by step opener assembly
instructions
2) Pictorial and step by step opener installation
instructions
For Help, call 1-800-35-GENIE or visit www.geniecompany.com
3
oVeRView of poteNtial haZaRDS
Overhead doors are large, heavy objects that move with the help of springs under high tension and electric motors . Since moving objects, springs
under tension, and electric motors can cause injuries, your safety and the safety of others depend on you reading the information in this manual . If you
have questions or do not understand the information presented, call The Genie Company . or your local Genie Distributor .
POTENTIAL HAZARD
EFFECT
PREVENTION
• Keep people clear of opening while door is moving.
• Do Not allow children to play with the door operator .
• Do Not operate a door that jams or one that has a broken spring .
MOVING DOOR
WARNING:
Could result in death
or serious injury .
• Turn off power before removing operator cover.
• When replacing cover, make sure wires are not pinched or near
moving parts .
• Operator must be properly grounded.
ELECTRICAL SHOCK
• Do Not try to remove, repair or adjust springs or anything to
which door spring parts are fastened, such as, wood blocks,
steel brackets, cables or other like items .
• Repairs and adjustments must be made by a trained door
system technician using proper tools and instructions .
HIGH SPRING TENSION
WARNING:
Could result in death
or serious injury .
WARNING:
Could result in death
or serious injury .
In this section, and those that follow, the words Danger, Warning and Caution are used to emphasize important safety
information . The word:
indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury .
indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury .
indicates a potentially hazardous situation which, if not avoided, may result in injury or property damage .
The word NOTE is used to indicate important steps to be followed or important considerations .
DANGER:
CAUTION:
WARNING:
Safe-T-Beam® (STB) Non-Contact Reversing System
Places an invisible beam across door opening, that reverses
the door during down travel to the fully open position if
anything passes through beam .
Safe-T-Reverse® Contact Reversing System
Automatically stops and reverses a closing door within 2
seconds of contact with an object .
Safe-T-Stop® Timed Reversed System
Automatically opens a closing door, if door does not close
within 30 seconds .
ForceGuard® Control
Used to set the force required for opening and closing
door . For maximum safety, set the minimum force required
to fully open and close door .
Automatic Lighting System
Light bulbs up to 60 Watts max . , used for safer entries and
exits . The lights turn on when door is activated and
automatically turn off 4 .5 minutes later .
Manual Emergency Release
Allows the garage door to be opened or closed manually
for emergencies or maintenance .
IMPORTANT INSTALLATION
INSTRUCTIONS
1 READ AND FOLLOW ALL SAFETY, INSTALL ATION AND
OPERATION INSTRUCTIONS . If you have any
questions or do not understand an instruction, call
your authorized Genie installation professional .
2 Do Not install operator on an improperly balanced
door . An improperly balanced door could cause
severe injury . Repairs and adjustments to cables,
spring assembly, and other hardware must be made
by a trained service person using proper tools and
instructions .
3 Remove all ropes, and disable all locks connected to
the door before installing operator .
4 Install door operator 7 feet or more above the floor .
Mount the emergency release knob 6 feet above
the floor .
5 Do Not connect the operator to the source of power
until instructed to do so .
6 Locate the control button:
• Within sight of door.
• At a minimum height of 5 feet, so small children
cannot reach it .
• Away from all moving parts of the door.
7 Install the entrapment WARNING label next to the
wall button or console . Install the emergency release
tag on, or next to, the emergency release
8 The operator must reverse when the door contacts a
1-1/2 inch high object on the floor at the center of
the doorway . This is about the size of a 2” x 4” board
laid flat .
t
o
ReDuCe
the
RiSk
of
SeVeRe
iNjuRy
oR
Death
:
WARNING:
S
afety
f
eatuReS
4
For Help, call 1-800-35-GENIE or visit www.geniecompany.com
Figure 1 Note Door Type
SECTIONAL DOOR, TORSION SPRINGS
SECTIONAL DOOR, EXTENSION SPRINGS
ONE-PIECE DOOR, TRACKLESS
m
eaSuRe
G
aRaGe
D
ooR
h
eiGht
A Measure door height (floor to top of door) using a tape measure .
B This new Garage Door Opener is designed for doors up to and
including 7’ 6” tall . If door height is 7’ 6” or less continue to Check Step 4 .
C
If door height is 8’-0”, you need a Rail Extension Kit . (Figure 3) .
(See Accessories Order Form, Page 16) .
D If the door height is taller than 8’-0”, the opener you purchased is
the wrong version . Contact your Customer Service Representative
at 1-800-354-3643 .
Check Step 3:
p
Re
-i
NStallatioN
C
heCkliSt
This Opener includes parts and supplies needed to install in most
garages and connect to most garage doors . There are many variations
of garages and garage doors . A few additional parts and supplies may
be needed to install Opener into your garage and connect to your
garage door . While checking items listed below, note any additional
items you will need .
Tools used in this section:
• 12’+ Tape Measure • Pencil • Ladder • Level
Check following items before assembling Opener:
C
heCk
D
ooR
C
oNDitioN
aND
t
hiCkNeSS
Check Step 1:
C
heCk
G
aRaGe
D
ooR
a
liGNmeNt
, o
peRatioN
,
aND
b
alaNCe
Check Step 2:
WARNING:
If your door sticks, binds, or is out of balance, have it adjusted
by a Genie Factory Authorized Dealer . Door springs, cables,
pulleys, brackets and associated hardware are under extreme
tension and can cause serious injury or death .
Torsion
Springs
Extension
Springs
Center
Stile
Center Stile
Header Area
Figure 3 Rail Extension Kit
Rail Extension for
8’ door
Check condition of vertical stile in center of door, and its connection to
door’s top and bottom beams . (Figure 1)
A If door frame is nailed together and not a solid connection, door
frame must be braced or reinforced before installing Opener .
B If door is “lightweight” (made with frame and skin - not solid),
door (including door frame) must be braced or reinforced before
installing Opener .
C A door opener reinforcement bracket may also be needed to
connect garage door to Opener’s Door Bracket . This Opener is
designed for installation on a properly braced sectional door or
solidly braced one-piece door .
D Contact your Genie Factory Authorized Dealer or dealer of your
garage door for any necessary bracing and a door opener
reinforcement bracket (if needed) before proceeding .
E
If you have a wooden door, measure door’s thickness . If your door
is less than 2” thick, brace door or use shorter Door Bracket Lag Screws
(1/4” x 1-1/4” – not included)
A Raise door, check alignment and see if it moves freely (Figure 2) .
If door appears out of alignment, binds, or does not move smoothly,
contact a Genie Factory Authorized Dealer or dealer of your garage
door for repairs and adjustments to door mechanism .
B Raise door to 3’ – 4’ above ground and carefully let go . Door
should stay stationary . Slight movement is acceptable . More than
slight movement means door is out of balance . Contact a Genie
Factory Authorized Dealer or dealer of your garage
door for repairs and adjustments to door mechanism .
B Find Header Bracket mounting height (Figure 4): (Do not attach
Header Bracket) .
•
Raise door, watching top edge of door and stop door
when its edge reaches its highest point .
•
Measure distance (“H”) from top edge of door to floor .
–
For sectional doors, add 2-1/2” to “H” . Mark a point
on center line . Bottom of Header Bracket will be
installed here .
–
For one-piece doors, add 6” to “H” . Mark this point on
center line . Bottom of Header Bracket will be
installed here .
C
heCk
D
ooR
h
eaDeR
a
Rea
A Find vertical center line of door and header:
•
Close door .
•
Measure door width at top .
•
Mark a point at center of door and on header directly
above door . Draw a center line to connect points .
Check Step 4:
NOTE
The header is a heavily reinforced section of the wall just
above the top of the garage door opening .
H + 2-1/2
H + 6
Figure 4 Find Highest Point of Travel
SECTIONAL DOOR
ONE-PIECE DOOR
HEADER
HEADER
H + 2-1/2
H + 6
C
Check door type . Make a note of whether it is a sectional or a
one-piece door for reference later (Figure 2) .
3’ - 4’
Sectional
Door
3’ - 4’
Figure 2 Checking door balance
One-Piece
Door
KEEP FEET CLEAR OF DOOR
Door Center Line
Figure 5 Check Power Head location
11’
Grounded
outlet
10’
(7’-6” door)
(8’ door)
5
For Help, call 1-800-35-GENIE or visit www.geniecompany.com
C
Check wall for a stud or a solid header at your mark: (If checking a
finished wall, a stud finder may be helpful) .
•
If location is above Header, a 2” x 6” board must be
screwed to studs beside your mark with at least two Lag
Screws and Flat Washers (not provided) .
•
Transfer your mark to new mounting board .
WARNING:
Door springs are under extremely high tension and
should be handled ONLY by a trained professional .
NOTE
• For all types and styles of doors:
– If the ceiling in your garage is so low that there is
not at least a 3” space above the Header Bracket
mounting point, contact a Genie Factory
Authorized Dealer .
• If a door spring is in the way, place the Header Bracket
above the spring . Do Not move the door spring .
C
heCk
p
oweR
h
eaD
m
ouNtiNG
a
Rea
Check Step 5:
Figure 6B Mounting methods for open beam or finished ceilings
FINISHED CEILINGS
Locate ceiling joists or trusses using
a stud finder or similar device .
Attach angle iron(not included) to
joists or trusses through finish
material using Lag Screws .
55 11
30
30
55 11
30
Perforated Straps
C
heCk
C
eiliNG
foR
G
RouNDeD
p
oweR
S
ouRCe
Check Step 6:
NOTE
Permanent wiring must be installed by a Licensed
Electrician . Not all Genie Factory Authorized Dealers
are Licensed Electrician’s . Contact someone who is a
Licensed Electrician .
WARNING:
Do Not use an extension cord! Extension cords can
cause dangerous overheating conditions .
Do Not use portable generator! This product is
designed to operate using standard house current .
Do Not use alternate power supplies,
A Check that there is a 15 Amp 120 Volt grounded electrical
outlet or grounded permanent wiring box (per building code)
within 3’ of Opener Power Head: Figure 5
•
If not, an outlet or wiring box must be installed . Contact
a licensed electrician for installation .
•
If building codes require permanent wiring, Power Head
must be partially disassembled to install appropriate
wiring in place of Power Cord . (See Assembly and
Installation Poster .)
C
heCk
S
afe
-t-b
eam
®
m
ouNtiNG
b
RaCket
l
oCatioN
Check Step 7:
Check for wood garage frame, jamb, or masonry at mounting
location (6” above floor) with attachment tabs facing away
from garage door (Figure 7) .
A If you cannot mount Safe-T-Beam® Mounting Bracket to
wood frame:
•
Concrete screws and concrete anchors (not included)
must be used to mount Brackets on masonry with
attachment tabs facing away from garage door .
Source
Sensor
Safe-T-Beam®
Mounting Bracket
Top of
Bracket
6” above
floor
Figure 7 Mounting
Safe-T-Beam®
Components
Check ceiling or space above where Opener Power Head will be
mounted (Figure 5): There must be a 120 Volt grounded outlet or
wiring box within 3 feet of Power Head .
A The measurements above are taken from the garage door
centerline toward the rear of the garage .
B Find location of ceiling joist or truss above where Opener Power
Head will be and estimate type and quantity of materials needed for
your installation (Figure 6A & B) .
MOUNTING EXAMPLES
Perforated Angle
Iron
Figure 6A
Standard Straps
Extra wood required
OPEN CEILINGS Straps and angle iron may attach directly to joists
or trusses .
6
For Help, call 1-800-35-GENIE or visit www.geniecompany.com
Figure 8 Recommended Tools
Go to Assembly and Installation Poster for full
Installation Instructions.
R
eCommeNDeD
toolS
A Tools (Figure 8):
B Additional tools to make installation easier:
•
Slotted and phillips screw-driver bits
•
Stud finder
•
Sheet-metal cutting snips
Check Step 8:
D
R
emoVe
e
xiStiNG
G
aRaGe
D
ooR
l
oCkS
Check that the garage door locks, rope, and T-Handles are
removed from the garage door before starting the installation .
A If your garage does not have a separate entry door, it is
highly recommended to install a Genie Emergency Release Kit
(GER-2) . Emergency Release Kit lets you open the garage door
from outside if there is a power failure . (Please see Accessories
Order Form on page 14 .)
Check Step 9:
Before going further, get any items and tools if needed
for your installation
p
Garage door frame reinforcement brackets, screws, bracing
or reinforcement kits (dealer)
p
Lag Screws (1-1/4”) for a wood door less than 2” thick (store)
p
Electrical outlet and/or wiring (supplied by a licensed electrician)
p
Sufficient angle iron or strapping for hanging Power Head (store)
p
60 Watt light bulbs (Rough service bulbs recommended)(store)
p
GER-2 Emergency Release Kit for entry during power failure (store)
p
Wood for header, ceiling, and/or door braces (store)
p
Masonry fasteners for Safe-T-Beam® Bracket installation (store)
p
Safe-T-Beam® Bracket Extensions (dealer)
p
Masonry drill bit (store)
p
Extension Kit (for 8’ Garage Doors)(dealer)
WARNING:
TO REDUCE THE RISK OF
SEVERE INJURY OR DEATH
IMPORTANT
SAFETY INSTRUCTIONS
1 READ AND FOLLOW ALL INSTRUCTIONS .
2 Never let children operate or play with the Door Controls . Keep
the Remote Control away from children .
3 Always keep the moving door in sight and away from people and
objects until the door is completely closed .
NO ONE SHOULD CROSS THE PATH OF A MOVING DOOR .
4 NEVER GO UNDER A STOPPED, PARTIALLY OPEN DOOR .
5 Test Opener monthly . The door MUST reverse on contact with
a 1-1/2” high object (or a 2” x 4” board laid flat) at the center of the
doorway on the floor . After adjusting either the Force or the Limit
of travel, retest the Door Opener . Failure to adjust the Opener
properly may cause severe injury or death .
6 When possible use the Emergency Release only when the door
is closed . Use caution when using this Release with door open .
Weak or broken springs are capable of increasing the rate of door
closure and increasing the risk of severe injury or death .
7 KEEP GARAGE DOORS PROPERLY BALANCED . See Owner’s
Manual . An improperly balanced door increases the risk of severe
injury or death . Have a Genie Factory Authorized Dealer make
repairs to cables, spring assemblies, and other hardware .
8
SAVE THESE INSTRUCTIONS.
NoteS, RemiNDeRS
7
For Help, call 1-800-35-GENIE or visit www.geniecompany.com
a
DjuStiNG
l
imit
S
witCheS
aND
f
oRCe
C
oNtRolS
Adjustment 1:
A Pre-set Force Controls to midpoint between Hi and LO
(Figure A-1) .
B
Adjust the Close Limit Switch: (Figure A-2) .
•
Press Wall Console to close garage door .
–
If door does not close completely, measure distance
from bottom of door to floor . Move Limit Switch
same amount toward door and try again .
–
If door reverses after contacting floor, move Limit
Switch toward Power Head and try again .
–
If door reverses before contacting floor, increase
Close force and try again .
–
If door fails to move, check Safe-T-Beam® System . See
Safe-T-Beam® Troubleshooting Guide on pg . 13, and
Opener System Self-diagnostic Troubleshooting
on pg . 11 .
•
Tighten Limit Switch Set Screw . Do not over-tighten
(strip) Limit Switch Set Screw .
C
Adjust Open Limit Switch: (Figure A-2) .
•
Press Wall Console to open garage door .
–
If door does not open completely, move Limit Switch
toward Power Head .
–
If door opens completely, but motor continues to
run, move Limit Switch toward door .
•
Tighten Limit Switch Set Screw . Do not over-tighten
(strip) Limit Switch Set Screw.
WARNING
• A moving garage door can cause serious injury
or death .
• Keep the path clear.
• Position the ladder to the side of the Power Head
so it is clear of all moving parts of the Opener
and the door .
• Set the door Opener to use the minimum force
needed to open the door .
NOTE
• Little effort is required to turn the Force
Adjusting Knobs .
• If the door stops moving while opening or closing,
adjust the Open Force or Close Force Controls
slightly clockwise (to slightly increase the force)
and retry the step .
• The Open Force and Close Force Controls are to be
set to the minimum force necessary to ensure the
door smoothly opens fully and closes completely .
• The garage door will move slowly the first time it
runs, until the Opener “learns” the type of door .
• Ensure the Magnetic Carriage Assembly is engaged
and is between the two Limit Switches before
operating the Opener .
NOTE
• To protect your new investment, your opener is
equipped with a Timer and Cycle Counter which
work together to prevent any chance of heat
damage to electrical circuits caused by too many
cycles in too short a time . If your Opener suddenly
stops responding to the Wall Console
- Do Not Unplug the Unit - simply wait
10 minutes for the Timer/Cycle Counter to
reset itself and try again .
a .
Every 10 minutes you wait restores 5 cycles
up to the maximum of 25.
• Unplugging the unit will prevent the Timer/
Cycle Counter from resetting.
D Test Door Opener:
•
Run door up and down a few times using Wall Console and
observe door travel .
•
Repeat steps above as needed to set Limit Switch positions .
E
Adjust Open Force to minimum needed:
•
Place door in closed position using Wall Console .
•
Gently adjust Open Force fully counterclockwise
(minimum force) .
•
Run Opener using Wall Console .
•
Observe that door runs to Open Limit Switch .
–
If not, adjust Open Force Control slightly clockwise,
close garage door, and open it again .
•
Repeat steps above until garage door runs smoothly
from Close Limit Switch to Open Limit Switch .
F
Adjust Close Force to minimum needed:
•
Place door in open position using Wall Console .
•
Gently adjust Close Force fully counterclockwise
(minimum force) .
•
Run Opener using Wall Console .
•
Observe that door runs to Close Limit Switch .
–
If not, adjust Close Force Control slightly clockwise,
open garage door, and close it again .
•
Repeat steps above until garage door runs smoothly
from Open Limit Switch to Close Limit Switch .
m
aiNteNaNCe
aND
a
DjuStmeNtS
Close
Limit Switch (door fully closed)
Carriage
(disengaged)
Carriage Magnet
Switch
Switch
Magnet
Open Limit Switch (door fully open)
Carriage
(disengaged)
Figure A-2 Setting Limit Switches
Force Controls
Figure A-1 Making Force Adjustments
8
For Help, call 1-800-35-GENIE or visit www.geniecompany.com
NOTE
The door must contact the 2” x 4” board before the
Carriage activates the Close Limit Switch . If not, readjust
the Close Limit Switch .
S
ettiNG
C
oNtaCt
R
eVeRSe
f
uNCtioN
Adjustment 2:
NOTE
Limit Switch and Force Adjustments must be completed
before checking the contact reverse function (Figure A-3) .
2” x 4” board
laid flat
Figure A-3 Checking Contact Reverse
A Open garage door using Wall Console .
B Lay a 2” x 4” board flat in center of doorway .
C
Close door using Wall Console .
D Check that door stops and reverses
within 2 seconds after it
contacts board:
•
If door does not reverse, decrease
Close Force until door reverses .
•
If door still does not reverse, move
CLOSE Limit Switch toward door .
E
Check Safe-T-Beam® System operation:
•
If beam is blocked, door will
not close .
Transmitter Compliance Statement
A To program one Button of a Remote Control (Figure MA-1):
•
Locate Learn Button and Learn Indicator Light
on back side of Power Head under the Lens
(Figure MA-2) .
•
Press and release Learn Button . Red Learn
Indicator Light will blink 2 times per second .
•
Press Remote Control Button once within 30
seconds . Red Learn Indicator Light will stay lit .
•
Press Remote Control Button again . Red Learn
Indicator Light will go out, indicating that
memory is stored .
B Program each additional Remote using step A above
(up to seven remotes) .
NOTE
• Each Remote Control must be programmed
separately .
• The Remote Controls will not cause the door
Opener to close the garage door if the Safe-T-
Beam® System is malfunctioning .
• When programming the Remote Controls, they
must be at least 24” from the Antenna Wire .
• If the red Learn Indicator Light blinks
approximately 4 times per second,
programming has stopped . If programming
has stopped, repeat the above steps .
• Each Button on a 2 or 3 Button Remote Control
is for a different Opener . You cannot use more
than one Button per Remote, per Opener .
• A maximum of seven Remote Controls or
Wireless Keypads can be stored into the
Receiver at one time . If a Remote Control
becomes lost, or if you want to delete a Remote
Control or Wireless Keypad, see “To Erase All
Receiver Memory .”
C
p
RoGRammiNG
the
R
emote
C
oNtRolS
Programming 1:
a
CCeSSoRieS
WARNING:
A moving garage door may cause serious injury or
death .
• Keep people clear of opening while door is moving .
• Do not allow children to play with the Remote
Controls .
If the Safety Reverse does not work properly:
• Close the door and disconnect the Opener using
the Emergency Release Cord .
• Do not use the door Opener, Remote Controls, or
Wireless Keypad .
• Refer to the door and door Opener Owner’s
Manuals before attempting any repairs .
9
For Help, call 1-800-35-GENIE or visit www.geniecompany.com
Learn Code Button
Figure MA-2 Learn Code Button and Indicator Light
A Install two 60 Watt light bulbs (not included) into Light
Sockets (Figure MA-4):
•
Rough service, 130 Volt bulbs are recommended .
B Install Lens into slots in Motor Cover .
C Install Genie Emergency Release Kit (GER-2) accessory,
if purchased .
D Installation is now complete .
Lens
1A
Snap Lens Hinges into
slots on back of Motor Cover
60 Watts
maximum
Push in
Latches
to
close Lens
Figure MA-4 Install Lens Cover and Light
Bulbs
To Erase All Remotes from Power Head Memory
A Press and hold Learn Button on Power Head for 10
seconds or until Learn Indicator Light goes out .
Memory is erased:
•
Program Transmitter/Receiver again as needed .
To Replace Remote Control Battery
A FOR NON-FLASHLIGHT MODELS (Figure MA-3)
•
Pop off the back of the transmitter .
–
Use coin, pen, screwdriver or any similar device .
–
Replace old Battery with new coin type battery .
•
Replace back of remote.
B FOR FLASHLIGHT MODELS
•
Pry open battery cover . (Notch built into cover .)
–
Replace old Battery with new AAA battery .
•
Snap shut battery cover.
Remote Control Operation
A Press Button on Remote Control . Garage door will move .
B Press Button again . Garage door will stop:
•
The door automatically stops at the end of the open or
close cycle .
C Press Button again . Garage door will reverse .
1 Button Compact Remote
w/Docking Station
Figure MA-1 Genie Remote Controls
3 Button Compact Remote
w/Docking Station
To program a Homelink® or Car2U Device:
(This GDO is Homelink® and Car2U compatible)
• Follow the Homelink® or Car2U instructions in your car
owner’s manual .
i
NStall
l
iGht
b
ulbS
aND
l
eNS
WARNING
Use the Wall Console included with Opener . Any other
wall console can cause the Opener to operate unexpect-
edly and the light to stop working .
Figure MA-3 Pry case open at the notch
10
For Help, call 1-800-35-GENIE or visit www.geniecompany.com
A Monthly:
• Door springs and door hardware:
– Oil door roller, bearings, and hinges using silicone
lubricant or light oil .
• Balance Door .
– Close door .
– Release Magnetic Carriage Assembly from Rail Assembly
by pulling down on Emergency Release Knob .
– Raise door manually 3’- 4’ and verify that door stays at
that position . See Check Step 2 on page 4 .
–
Reattach Magnetic Carriage Assembly to Rail Assembly by
pulling the Emergency Release Knob toward Power Head .
–
Close door .
• Contact Reverse Test.
– Perform Adjustment 2 on page 8 .
NOTE
When the door is 3’ - 4’ above the ground, the door
should stay open . Slight movement is acceptable . If
the door moves too much, contact a Genie Factory
Authorized Dealer for service or call Customer Service at
1-800-35-GENIE.
WARNING
Do not operate door automatically or manually if springs
are broken . Contact a Genie Factory Authorized Dealer for
service or call Customer Service at 1-800-35-GENIE .
MAINTENANCE
B Yearly:
• Wipe off old excess lubricant from Drive Screw .
• Lubricate Drive Screw with Genie Lubricant (GLU-3)
WARNING
If the door fails to reverse on contact with the board,
adjust the Close Force Control as specified in Set Limit
Switches and Force Controls on page 7 . If the Opener still
fails, contact a Genie Factory Authorized Dealer for service
or call Customer Service at 1-800-35-GENIE .
NOTE
Use ONLY Genie Lubricant (GLU-3) . Other lubricants
may damage the Opener .
FCC AND IC CERTIFIED
All devices comply with Part 15 of the FCC Rules .
Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2)
this device must accept any interference received, includ-
ing interference that may cause undesired operation .
Screw Drive Garage
Part N
o. GLU
-3
Door Opener Lubricant
GLU-3
Lubricant
t
RoubleShootiNG
G
uiDe
Safe-T-Beam® System Self-Diagnostic Troubleshooting
Source (Red LED)
Sensor (Green LED)
Possible Problem
Solution
ON
ON
Normal operation
None required
OFF
OFF
• Power Head not powered
• Check breakers, fuses, plugs
• Wiring from Power Head bad
• Check wiring for obvious shorts
OFF
ON
• Wiring to Source missing or bad • Check wiring
• Power has been interrupted
• Remove power and reapply
2 BLINKS, Pause
• Beam not aligned
• Check Source, Sensor alignment
(Repeat)
ON
• Beam obstructed
• Check for obstruction
• Sensor defective
• Contact Customer Service
2 BLINKS, Pause
• Wire to Sensor missing or bad
• Check wiring
(Repeat)
OFF
• Sensor defective
• Contact Customer Service
3 BLINKS, Pause
• Sensor receiving interference
• Determine source of interference
(Repeat)
ON
• Contact Customer Service
4 BLINKS, Pause
• Source not sending pulses
• Contact Customer Service
(Repeat)
ON
• Source defective
• Contact Customer Service
11
For Help, call 1-800-35-GENIE or visit www.geniecompany.com
Opener System Self-Diagnostic Troubleshooting
•
See Status Light on Figure MA-2, page 9)
You See
Problem
What to Do
Reference
1 BLINK,
Motor Drive
• Reset Opener—unplug (or disconnect power), wait 5 seconds, plug
Pause
Board
back in (reapply power), and activate from Wall Console .
(Repeat)
Interrupt
Normal
• First Cycle will run at slow speed .
operation
restored
If the problem • Check door condition . NOTE: This Opener is equipped with an
See Door
recurs
automatic garage door balance detection system. An improperly Safety Guide
balanced door, damaged or worn counter-balance spring, binding
door hardware or rollers may result in a “ONE-BLINK” signal.
• Contact Customer Service for further assistance .
Operation not • Check door condition .
1 . See page 4 .
restored
• Have a Genie Factory Authorized Dealer check:
2 . See door
– Fuse on Motor Drive Board .
Safety Guide
– Ribbon Cable on Motor Drive Board is properly inserted into
Connector on Controller Board .
• Contact Customer service for further service .
2 BLINKS,
Controller
• Reset Opener — unplug (or disconnect power), wait 5 seconds, plug
Pause
Board
back in (reapply power), and activate from Wall Console .
(Repeat)
Interrupt
• Have a Genie Factory Authorized Dealer check that Ribbon Cable on
Motor Board is properly inserted into connector on Controller Board .
• Contact Customer Service for further assistance .
3 BLINKS,
Opener
• Do not unplug or disconnect power from Opener. Wait 10 minutes
Pause
Overheated
for internal clock to provide additional cycles. Cycles are restored
(Repeat)
or
at a rate of 5 cycles per 10 minutes of rest.
Over-cycled
• Contact Customer Service for further assistance.
4 BLINKS,
Force Settings • Check Force Settings .
NOTE: Force Settings are not pre-set at factory. 1 . See page 7 .
Pause
Incorrect
• Check door condition .
2 . See Door
(Repeat)
• Contact Customer service for further assistance .
Safety Guide
5BLINKS,
Safe-T-Beam® • Check Safe-T-Beam® Self-diagnostic System . NOTE: Safe-T-Beam®
See page 13 .
Pause
Malfunction
System must be installed and operational to enable door to close.
• Contact Customer Service for further assistance .
6 BLINKS,
Wall Console
• Check Wall Console Wiring for shorts, tight Staples, or pinched Wires .
Assembly and
Pause
does not work • Check Wiring Connections at Power Head and Wall Console .
Installation
(Repeat)
• Contact Customer Service for further assistance .
Poster .
7 BLINKS,
Limit Switches • Check Limit Switch Wire connections to Terminals on Power Head .
Assembly and
Pause
not working
• Check for shorted or pinched Wires under Limit Switch Brackets .
Installation
(Repeat)
• Contact Customer Service for further assistance .
Poster .
8 BLINKS,
Wall Console
• Vacation Locking Switch on Wall Control is in “Lock” mode .
Assembly and
Pause
locked
Unlock switch .
Installation
(Repeat)
• Contact Customer Service for further assistance .
Poster .
NOTE
• The status LED Indicator Light is located under the Lens Cover. The Green LED light will turn ON, then OFF when
power is applied to the Opener . If LED stays ON, have a Genie Factory Authorized Dealer check the Controller
Board, or call Customer Service at 1-800-35-GENIE .
• If Safe-T-Beam® problems exists, the door can be closed electrically by holding the Wall Console Button down
until door is fully closed .
• The Remote Controls and Wireless Keypad will not work without a working Safe-T-Beam® System.
12
For Help, call 1-800-35-GENIE or visit www.geniecompany.com
General Troubleshooting (Always Check the Status LED Light)
Problem
What To Do
Opener does not run
1 . Check power source .
from Remote Control
A . If Opener is connected to an outlet
:
• Plug a working lamp into outlet used for Power Head .
• If lamp glows, power source and outlet are OK .
• If not, check fuse or circuit breaker or non-compatible GFCI .
NOTE: A licensed electrician must replace non-compatible GFCI’s.
B . If Opener is connected to a wiring box:
• Check that fuse is not blown, or circuit breaker is on and not tripped or off .
• If still no power, have a licensed electrician check circuit and wiring .
2 . If Power Source is OK
:
•
Check Power Head Terminal connections (Wall Console Installation on Assembly & Installation Poster), tighten if loose .
•
Check
connections at Wall Console Terminals, tighten any loose connections .
Have a Genie Factory Authorized Dealer check that Ribbon Cable between Controller Board and Motor Drive
Board is properly connected to Connectors on Circuit Boards, or call Customer Service at 1-800-35-GENIE .
Door Opener starts
• Check Wires to ensure that they are not cut (Stapes can cut insulation and short Wires) .
for no apparent reason
Replace any shorting Staples and shorted Wires .
• Was Remote Control lost or stolen? If so, erase all Remote Control codes from Receiver’s memory
and reprogram for remaining remote controls . (See Erase All Receiver Memory on page 8) .
• Ensure that no Buttons are stuck “pushed-in” on Wall Console or any Remote Controls .
Door starts down, then
• Check Close Limit Switch setting (see Set Limit Switches and Force Controls on page 7) .
stops before it is
Adjust as needed .
completely closed
• Check for shorted Wires .
• Check garage door for binding .
Door starts down, then
• If a new installation, check Door Arm position .
stops and goes back up
• Check operation of Contact Reverse function .
• Check Safe-T-Beam® System for beam obstruction or misalignment of Lenses .
• Check Safe-T-Beam® System diagnostic code .
• Check Close Force adjustment (see Set Limit Switches and Force Controls on page 7) . Adjust as needed .
• Check garage door for binding .
Door will only run closed
• Check Open Limit Switch for a short circuit and for proper wiring .
• Check Open Force adjustment (see Set Limit Switches and Force Controls on page 7) . Adjust as needed .
• Check condition of garage door and door spring(s) .
• WARNING: If you suspect a problem with the garage door hardware or springs, contact a Genie
Factory Authorized Dealer for service, or contact Customer Service at 1-800-35-GENIE .
Door will only run open
• Check Safe-T-Beam® System as detailed in the Safe-T-Beam® System Self-diagnostic Troubleshooting Chart
(see Safe-T-Beam® System Self-diagnostic Troubleshooting Section on page 13) .
• Check Close Limit Switch for a short circuit and for proper wiring .
• Check Close Force adjustment (see Set Limit Switches and Force Controls on page 7) . Adjust as needed .
Lights will not go out
• Disconnect Wires connected to Wall Console . (Wall Console Installation on
Assembly & Installation Poster
) .
Check their condition and either replace or reconnect .
• Until a replacement Wall Console can be obtained, disconnect Wall Console and use only Remote Controls
or Wireless Keypad to operate Opener .
Door starts up, but stops
• Check (ensure) that garage door and Opener are in good repair, properly lubricated, and properly
before it is
balanced as detailed in Maintenance Section .
completely open
• WARNING: If you suspect a problem with the garage door hardware or springs, contact a Genie
Factory Authorized Dealer for service, or contact Customer Service at 1-800-35-GENIE .
• Check Open Limit Switch for a short circuit and for proper wiring .
• Check Open Force adjustment (see Set Limit Switches and Force Controls on page 7) . Adjust as needed .
Operator runs, but door
• Ensure Magnetic Carriage Assembly is engaged to Rail Drive Screw (see Install Magnetic Carriage Assembly
does not move
onto Rails on page 10) .
• Check Force adjustment (see Set Limit Switches and Force Controls on page 7) . Adjust as needed .
• Check that all sections of Rail Drive Screw are turning when Motor runs . If not:
– Check condition (not cracked, split, or broken) and placement of Coupler . Replace as needed .
– Check condition (not cracked, split, or broken) and placement of Collar and Clip . Replace them
as needed .
Wall Console Vacation
• Ensure Magnetic Carriage Assembly is in contact with Close Limit Switch .
Lock function does
• Check when door is fully closed, that Carriage activates Close Limit Switch . If not, adjust position of Close
not work
Limit Switch (See page 7) .
continued on next page
13
For Help, call 1-800-35-GENIE or visit www.geniecompany.com
General Troubleshooting (Always Check the Status LED Light)(Continued)
Problem
What To Do
Remote Control has less
• Relocate Remote Control inside car .
than 25’ operating range
• Ensure Remote Control is pointing toward garage door when pressing Control Button .
• Replace Remote Control Battery (See page 9) .
• Reposition Opener Antenna Wire .
• Do Not attempt to retune Remote Controls or Receiver .
Opener works from Wall
• Program code for each Remote Control into Receiver memory (See Programming the Remote
Control, but not from
Control on page 8 .
Remote Control
• Replace Remote Control Battery (See page 9) .
• Check Safe-T-Beam® System for beam obstruction or misalignment of Lenses .
• Check Safe-T-Beam® System for any diagnostic codes . If present, troubleshoot as detailed in
Safe-T-Beam® System Self-Diagnostic Troubleshooting Chart (See page 10) .
Noisy operation
• Ensure all fasteners are tightened .
• Check that the garage door and Opener are in good repair, properly lubricated, and properly
balanced . (See Maintenance page 10) .
• WARNING: If you suspect a problem with garage door hardware or springs, contact a Genie
Factory Authorized Dealer for service, or contact Customer Service at 1-800-35-GENIE.
Safe-T-Beam® System
• If an operational problem exists, Opener will not run closed .
• Check Safe-T-Beam® System for beam obstruction or misalignment of Lenses .
• Check Safe-T-Beam® System for any diagnostic codes . If present, troubleshoot as detailed in Safe-T-Beam®
System Self-Diagnostic Troubleshooting Chart (See page 13) .
Door closes, and Opener
• Check position of Wall Console Vacation Lock Switch . It must be in UNLOCKED position for Opener to
shuts down
open door .
continued on next page
MOTOR
WHITE
WHITE
WHIT
E
BR
O
W
N
BR
O
WN
STRIPE
YELL
O
W
GREEN
O
R
A
NGE
WHITE
WHITE
BLUE
BLACK
GREEN
WALL CONTROL
OPEN LIMIT
CLOSE LIMIT
CONTROLLER BO ARD
MOTOR DRIVE BOARD
PRIMARY GROUND
LIGHTS
(60 WATTS MAX.)
LINE
PLUG
WARNING
Opening Cover May Result in Electric Shock
w
iRiNG
D
iaGRam
14
For Help, call 1-800-35-GENIE or visit www.geniecompany.com
Item
Part Name
Quantity
Item
Part Name
Required
1
Power Head Assembly (main carton)
1
2
1/4”-20 x 13/16” Hex Head Shoulder Bolt (blue bag)
2
(yellow shoulder bolt)
4
Rail Assembly, 3 piece (main carton)
1
4A
First Rail Section (main carton)
1
4B
Middle Rail Section (main carton)
1
4C
End Rail Section (main carton)
1
8
1/4”-20 Hex Serrated Flange Nut (blue bag)
4
9
Rail Clamps (main carton)
4
10
5/16”-18 x 11/16” Hex Head Shoulder Bolt (blue bag)
8
11
5/16”-18 Hex Serrated Flange Nut (blue & orange bags)
12
12
Magnetic Carriage Assembly (main carton)
1
13
Collar (blue bag)
3
14
Retaining Clip (blue bag)
3
15
Rail Strap (blue bag)
1
16
1/4”-20 Hex Head Bolt (blue bag)
2
18
Open Limit Switch Assembly (White)(green bag)
1
19
Close Limit Switch Assembly (Brown) (green bag)
1
21
# 8-32 x 1” Hex Head Screw (green bag)
2
22
Emergency Release Cord (main carton)
1
23
Emergency Release Cord (main carton)
24
Emergency Release Knob (main carton)
1
25
Emergency Release Tag (main carton)
1
26
Header Bracket (orange bag)
1
28
Door Bracket (orange bag)
1
30
1/4” x 2” Lag Screw (orange bag)
8
31
Straight Door Arm (main carton)
1
32
Clevis Pin, 3/8” x 15/16” (yellow bag)
2
33
Cotter Pin, .073” dia . (yellow bag)
2
34
Curved Door Arm (main carton)
1
35
3/8” x 7/8” Hex Head Bolt (yellow bag)
2
36
3/8” Hex Serrated Flange Nut (yellow bag)
2
37*
2-Conductor Wire (main carton)
1 Roll
38*
Insulated Staple (red bag)
approx . 30
40*
Wall Console (main carton)
1
41*
# 6 x 1-1/4” Pan Head Screw (red bag)
2
42*
Entrapment Warning Label (manual)(main carton)
1
43*
Safe-T-Beam Sensor (Green LED)(main carton)
1
44*
Safe-T-Beam Source (Red LED)(main carton)
1
45*
Safe-T-Beam Bracket (yellow bag)
2
46
Coupler (blue bag)
1
47*
# 10 x 1 1/4” Phillips Hex Head Screw (yellow bag)
4
48*
One Button Remote Control (main carton)
49*
Three Button Remote Control (main carton)
50*
Wireless Keypad (main carton)
51*
Two Button Remote Control (main carton)
52*
Safety & Maintenance Guide (manual)(main carton)
1
53
Wire Clip (green bag)
7
54
Carriage Stop (blue bag))
1
55*
5/16”-18 x 3/4” Hex Head Bolt (orange bag)
3
56
1/4-20 x 3/4” Self-drilling Screw (orange bag)
3
57
Mounting Straps (main carton)
2
58
Wall Button (red bag)
1
*
Denotes items not shown on page 15 . These items will be illustrated
throughout the manual as required .
Parts List
[1]
Item
Part Name
1A
Lens
1B
Top Plate Assembly
1C
Light Socket (2)
1D
Motor Assembly
1E
Motor Cover
1G
Motor Drive Board
1H
Controller Board
1K
# 10-24 x 3/8” Hex Head
1L
# 8-32 x 1” Phillips Screw
1M
# 8-32 x 3/8” Slotted Hex Head Screw
1P
Power Cord
p
oweR
h
eaD
a
SSembly
e
xploDeD
V
iew
POWER HEAD ASSEMBLY PARTS LIST
varies/
model
varies/
model
varies/
model
varies/
model
Serial Number
Model Number
15
For Help, call 1-800-35-GENIE or visit www.geniecompany.com
h
aRDwaRe
e
xploDeD
V
iew
NOTE
Opener will not function unless Safe-T-Beam® System is installed and Force Controls are properly set .
16
For Help, call 1-800-35-GENIE or visit www.geniecompany.com
®
No C .O .D . shipments . Please include check or money
order, made payable to The Genie Company . Do not send
cash . Allow 3-4 weeks for delivery .
1-800-354-3643 . Please have part number and credit
card ready . Mail Order Form to: Genie Company, 22790
Lake Park Blvd, Alliance, Ohio 44601 . We accept Visa or
Mastercard on phone orders only .
Please add local sales tax if you reside in one of the states listed .
California, Connecticut, Florida, Georgia, Illinois, Indiana, Maryland,
Massachusetts, Michigan, New Jersey, New York, Ohio, Tennessee,
Virginia, Wisconsin
TOTAL ORDER
$
SHIPPING & HANDLING
$ 5 .00
STATE SALES TAX
$
GRAND TOTAL
$
Pas d’expédition contre remboursement . Veuillez inclure un chèque
ou un mandat bancaire, le payable fait à The Genie Company .
N’envoyez pas d’argent comptant . Accordez de 3 à 4 semaines
pour la livraison . 1-800-354-3643 . Ayez sous la main le numéro de la
pièce et celui de la carte de crédit . Mettre à la poste le arrngement
à: Genie Company, 22790 Lake Park Blvd, Alliance, Ohio 44601 . Nous
acceptons les commandes par téléphone avec paiement par carte
de crédit Visa ou Mastercard .
Veuillez indiquer les taxes de vente locales si vous résidez dans l’un des états
répertoriés ci-dessous .
COMMANDE TOTALE
$
MANUTENTION ET EXPÉDITION
$ 5 .00
TAXE DE VENTE
$
TOTAL GLOBAL
$
No se aceptan pedidos de pago contra entrega (COD) .
Sírvase incluir su cheque o giro postal, la cuenta pagadera
hecha aThe Genie Company . No envíe dinero en efectivo .
Concédanos 3 a 4 semanas para la entrega . 1-800-354-3643 .
Sírvase tener listos los números del modelo y de la tarjeta
de crédito . Enviar hacer un pedido de mercancia a: Genie
Company, 22790 Lake Park Blvd, Alliance, Ohio 44601 .
Aceptamos pedidos telefónicos de Visa o Mastercard .
Sírvase agregar el impuesto de ventas local si usted reside en uno de los
siguientes estados:
Ordering Instructions
Las Instrucciones que Ordenan
Instructions Commandant
Screw Drive Garage
Door Opener Lubricant
(GI CT390-1)
1-Button Compact Remote - Allows remote operation of garage door .
Comprima el Mando de Distancia - Proporciónar operación remoto de la puerta del garaje .
Télécommande compacte - Permettre opération éloign´´de porte de garage .
(GI CT390-3)
3-Button Compact Remote - Allows remote operation of 3 garage doors .
De 3 botones Comprima el Mando de Distancia - Proporciónar operación remoto de tres las puertas del garaje .
3-boutenner la Télécommande compacte - Permettre opération éloign´ trois portes
de garage .
(GWKPD)
Wireless Keypad - Operates Intellicode
®
Garage Door Openers without Remote Control or key .
Sistema de entrada por teclado numérico inalámbrico - Acciona los abridores de puertas de garaje Intellicode
®
sin
control remoto o llave .
Système d’ouvre-porte de garage à clavier sans fil - Actionne les ouvre-porte de garage avec Intellicode
®
sans
télé-
commande ni clé .
(GLU-3)
3/4 oz. Screw Drive Lubricant - Ensures proper equipment wear protection .
3/4 once Lubricante de tornillo accionar - Asegura componente correcto protección por deterioro .
La onza 3/4 Lubricant de la vis - Garantir componant exact par systéme défense vers user .
(GPS-5)
Perfect Stop
®
- Ensures perfect parking .
Stop Perfecto
®
- Asegura el estacionamiento perfecto .
Butoir Perfect Stop
®
- Permet de stationner à la perfection dans le garage .
(LCGX-8)
ChainLift Extension Kit - An Extension that increases the travel of an Opener to accommodate an
eight foot door .
Juego de extensión de cadena deslizable - Una extensión para aumentar la longitud de la baranda de Chain
Glide, para acomodar una puerta de 8 pies (2,43 m) .
Nécessaire de prolongement du coulisseau - Rallonge de prolongeant la course de l’ouvre-porte Chain Glide
pour une porte de 2,4 m (8 pi) de hauteur .
(60 WATT
) Enhanced/Rough Service Light Bulb - Ensures proper equipment compatability .
Bombilla de 60 Vatios - Asegura componente correcto de sistema .
éclairage de 60 WATT - Garantir componant exact par systéme .
(GER-2)
Emergency Release Kit - Provides access to garage from outside in the event of
an electrical power failure .
Juego de pica-porte de pestillo - Permitir entrtada desde por fuera de garaje porque corte
de eléctrico .
Nécessaires de Déclenchement de secours - Le nécessaire de déclenchement
de secours est conçupour vous permettre d’accéder à votre garage depuis
l’extérieur en cas de panne de courant et lorsqu’il .
STB
Adapter Brackets (2) - Used in conjunction with standard STB Brackets . They provide
additional clearance and mounting options .
El adaptador pone entre paréntesis (2) - Usado en unión con paréntesis uniformes de
montar de STB, ellos proporcionan el espacio libre adicional junto con mortar las opciones .
Crochets d’adaptateur (2) - Utilisé conjointement avec STB standard monter les crochets,
ils fournissent le dégagement supplémentaire avec monter d’options .
(GSXL-8)
Screw Drive Extension Kit - An Extension to increase travel of an Operator to accommodate
eight foot door .
Juego de extensión deslizante de Screw Drive - Una extensión para aumentar la carrera de un abridor
deslizable, para acomodar una puerta de 8 pies (2,43 m .) .
Nécessaire de rallonge du Screw Drive - Rallonge de prolongeant la
coursede l’ouvre-porte pour une porte de 2,4 m (8 pi) de hauteur .(GIRU-1T)
SHIP ORDER TO:
ENVIAR MERCANCIA CON:
EXPÉDIER MARCHANDISE POUR:
NAME / NOMBRE / NOM
ADDRESS / DIRECCIóN / ADRESSE
CITY / CIUDAD / VILLE
STATE / ESTADO / ÉTAT
ZIP / CóDIGO POSTAL / CODE POSTAL
California, Connecticut, Florida, Georgia, Illinois, Indiana, Maryland,
Massachusetts, Michigan, New Jersey, New York, Ohio, Tennessee,
Virginia, Wisconsin
California, Connecticut, Florida, Georgia, Illinois, Indiana, Maryland,
Massachusetts, Michigan, New Jersey, New York, Ohio, Tennessee,
Virginia, Wisconsin
How many?
¿Quántos?
$36.50
$50.00
$35.00
$50.00
$5.00
$3.75
$4.00
$32.00
$34.95
$2.73
$20.00
$4.37
P/N 36248R
P/N 36223R
P/N 35661R
P/N 35691R
P/N 35218A.S
P/N 35693R
P/N 35677R
P/N 35679R
P/N 33523S
(GWC-2W)
Deluxe Wall Console - Operates Garage Door . Independent light control . Security vacation lock .
Consola de lujo de pared - Acciona la puerta del garaje . Control de luz independiente . Cerradura de
seguridad para vacaciones .
La Console dse luxe de Mur - Actionne la porte de garage . Commande d’éclairage indépendante .
Interrupteur de verrouillage de sécurité .
P/N 26210A.S
P/N 35675R
(Prices subject to change without notice)
(Valoran el cambio con sujeción a sin nota)
(Les prix assujettissent pour changer sans la notification)
P/N 34439R.S
Garage Door Opener Accessories Order Form
Formulario de pedido de accesorios para abridores de puertas de garaje
Formulaire de commande des accessoires pour ouvre-porte de garage
For additional accessories not shown . visit our website at www .geniecompany .com
Para accesorios adicionalesno mostrada, visite nuestro sitio web en www .geniecompany .com
pour les accessoires supplémentaires pas montré, visiter notré site web à www .geniecompany .com
TOTAL DEL PEDIDO
$
FLETE Y MANEJO
$ 5 .00
IMPUESTO DE VENTAS ESTATAL
$
GRAN TOTAL
$
$45.00
P/N 35657R
(GI F TD-1)
1-Button Flashlight Transmitter - Remote Controller with a Flashlight .
1 abrocha transmisor de linterna - Director remoto con una linterna .
1-boutenner l’émetteur de lampe de poche - Le contrôleur éloigné avec de lampe de poche .
(GW-2)
Universal Wall Button - Provides additional convenient inside operation of door .
Botón de pared universal - Proporciona operación conveniente de la puerta desde el interior .
Bouton mural universel - Actionne l’ouvre-porte de l’intérieur du garage .