Genie DirectLift 2060 Operation And Maintenance Manual

Download PDF User Manual

Full Text Searchable PDF User Manual

omplete

with

ntelliCode

emote

ontRol

and

SeRieS ii

leCtRoniCS

able

ontentS

Warranty Information  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 2
Safety Information    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 3
Safety Features   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 3
Important Installation Instructions  .  .  .  .  .  .  . 3
Pre-Installation Checklist  .  .  .  .  .  .  .  .  .  .  .  .  .  . 4-6
Adjustments  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 7-8
Programming the Remote Control   .  .  .  .  .  . 9
Installing lightbulb and lens  .  .  .  .  .  .  .  .  .  .  .  .  . 9
Scheduled Maintenance   .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 10
Troubleshooting Guide   .  .  .  .  .  .  .  .  .  .  .  .  .10-11
Wiring Diagram  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 12
Parts Lists and Exploded Views  .  .  .  .  .  .12-13
Accessories  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 14

For up to 7’-6” tall Doors. (Extension Kit available for 8’

Doors)
Included Wall Control MUST be installed prior to Operation of

this Garage Door Operator.
Safe-T-Beam® Safety Reverse System Must be Installed and

the Force Controls MUST be Properly Set to close door.
This Equipment meets or exceeds all Federal, State and UL

325 Safety Requirements.

L F

FUTURE

REFERENCE

Having Difficulty? Need Help?

Please call us: 1-800-35-GENIE (354-3643)

www.geniecompany.com
Please have Model information

ready when calling

3622836177

AC POWERED SCREW DRIVE OPENERS

2060

3060

Operation and
Maintenance Manual

For Help, call 1-800-35-GENIE or visit www.geniecompany.com

Model Number and
Serial Number are
located on front panel
inside the lens .

INCLUDED IN THIS PACKAGE
Manual 1) Warranty Information

2) Pre Installation Checklist to be reviewed prior

to any assembly or installation

3) Necessary Adjustments

4) Programming Remote Devices

5) Maintenance and Troubleshooting

6) Parts Explosions

7) Accessory Order Form

8) Door Opener Association Safety and

Maintenance Brochure (DASMA)

9) Entrapment Warning Label - To be Adhered in

close proximity to wall control

Poster 1) Pictorial and step by step opener assembly

instructions

2) Pictorial and step by step opener installation

instructions

IT IS CRITICAL THAT ALL SAFETY WARNINGS

MARKED CLEARLY IN BOTH THE MANUAL

AND POSTER ARE READ, UNDERSTOOD AND

FOLLOWED.

enie

ompany

imited

aRRanty

What is covered?
Any defect in material and product workmanship from personal, normal

household use in accordance with the Owner’s Manual .
For how long?

MODEL 2060L-07 . . . 15 years on motor, 3 years all other parts .

MODEL 3060L-07 . . . Lifetime* on motor, 3 years all other parts .

*Lifetime = For as long as you own your home .
Who gets the warranty?
This warranty is limited to the consumer who originally purchased the prod-

uct .
Geographic scope:
This warranty applies only to units installed and operated within the country

where they were purchased .
Limitations:

IMPLIED WARRANTIES, I N CLUDING THOSE OF FITNESS FOR A PAR TICULAR

PURPOSE AND MERCHANT ABILITY (AN UNWRITTEN WARRANTY THAT THE

PRODUCT IS FIT FOR ORDINARY USE), ARE LIMITED TO ONE YEAR FROM

THE DATE OF PURCHASE . GENIE WILL NOT PAY FOR: LOSS OF TIME;

INCONVENIENCE; LOSS OF USE OF YOUR GENIE PRODUCT OR PROPERTY

DAMAGE CAUSED BY YOUR GENIE PRODUCT OR ITS FAILURE TO WORK; ANY

SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES; OR ANY DAMAGES

RESULTING FROM MISUSE OR MODIFICATION OF YOUR GENIE PRODUCT .
Some states and provinces do not allow limitations on how long an implied

warranty lasts or the exclusion of incidental or consequential damages, so the

above limitations or exclusions may not apply to you .
This warranty is the only one we will give on your Genie product, and it sets

forth all our responsibilities regarding your Genie product . There are no other

express warranties .
State and province rights: This warranty gives you specific legal rights, and

you may also have other rights which vary from state to state and province to

province .
How to get warranty service:
To obtain warranty service for your Genie product, you must provide proof of

the date and place of purchase of the product .
1. Do-It-Yourself-Service

Call the Genie Customer Service toll free at 1 .800 .354 .3643 to speak in

person to a trained Genie representative for assistance in diagnosing the

problem and arranging to supply you with the required parts for do-it-

yourself repairs . Trained service representatives are available Monday-Friday,

8:00 a .m . - 11:00 p .m ., Eastern Time, and on Saturday, 10:00 a .m . to 8:00 p .m .,

Eastern Time (subject to holidays) You may also get the information you

need at

www.geniecompany.com

2. Service From Authorized Dealers

You also may obtain warranty service from Genie authorized dealers by calling the

Genie Customer Service at 1 .800 .354 .3643 or by visiting

www.geniecompany.com

before scheduling warranty service . If warranty service is provided by an authorized

dealer, Genie will provide all required parts under war ranty at no charge to you, but

the dealers are independent business people and may render a bench or ser vice call

charge for their services . Genie will not reimburse you or other wise be responsible for

those charges .

We suggest that you retain your original packing material in the event we choose to

repair or replaqce your Genie Product and request that you ship it to us . Be sure to

include your name, address, telephone number, proof of date and place of purchase

and a description of the operating problem . After repairing or replacing, your Genie

product, we will ship it to your home at no cost to you for parts and labor, but you will

have to pay a minimum of $5 .00 for shipping and handling charges .

Your choice of either one of the above-described service options is your exclusive

remedy under this warranty .

What this warranty does not cover:

This warranty does not cover batteries (which are considered replaceable parts),

installation, commercial use, defects resulting from accidents, damage while in transit

to our service location or damage resulting from alterations, misuse or abuse, lack of

proper maintenance, unauthorized repair or modification of the product, affixing of

any attachment not provided with the product, programming of the Remote Control

Devices, Safe-T-Beam® adjustment/cleaning, staples through wiring, pinched or broken

wires, Carriage disengaged, Force Control adjustments, door out of balance, broken

springs or cables, power outages, use of extension cords, missing or damaged parts on

discounted, clearanced, final sale or taped cartons, phantom operations (labor is not

covered if Opener is functioning properly while technician is in garage),fire, flood, or

acts of God, or other failure to follow the Owner’s Manual .

SAVE THESE INSTRUCTIONS

Visit Our Website at:

www.geniecompany.com

FOR ANSWERS: CALL 1.800.354.3643

Please note the following information,so it is available if you

need to call us.
Date Purchased

__________/_________/__________

Serial Number

______________________________

Operator Model

______________________________

Remote Control Model ______________________________
Dealer Name

______________________________

Dealer Address

______________________________

City

______________________________

State / Zip

______________________________

NOTE

Please keep original or photocopy of your sales receipt

with this manual for future reference should service

ever be required.

For Help, call 1-800-35-GENIE or visit www.geniecompany.com

oVeRView of potential haZaRdS

Overhead doors are large, heavy objects that move with the help of springs under high tension and  electric motors .  Since moving objects, springs
under tension, and electric motors can cause injuries,  your safety and the safety of others depend on you  reading the  information in this manual .  If you
have questions or do not understand the information  presented,  call The Genie Company .  or your local Genie Distributor .

POTENTIAL HAZARD

EFFECT

PREVENTION

• Keep people clear of  opening while door is  moving.
• Do Not allow children to play with the door  operator .
• Do Not operate a door that jams or one that has a  broken spring .

MOVING DOOR

WARNING:

Could result in death

or serious injury .

• Turn off power before removing operator cover.
• When replacing cover, make sure wires are not pinched or near

moving parts .
• Operator must be properly grounded.

ELECTRICAL SHOCK

• Do Not try to remove, repair or adjust springs or anything to

which door spring parts are fastened, such as, wood blocks,

steel brackets, cables or other like items .
• Repairs and adjustments must be made by a trained door

system technician using proper tools and instructions .

HIGH SPRING TENSION

WARNING:

Could result in death

or serious injury .

WARNING:

Could result in death

or serious injury .

In this section, and those that follow, the words Danger, Warning and Caution are used to emphasize important safety
information . The word:

indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury .

indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury .

indicates a potentially hazardous situation which, if not avoided, may result in injury or property damage .

The word NOTE is used to indicate important steps to be followed or important considerations .

DANGER:

CAUTION:

WARNING:

Safe-T-Beam® (STB) Non-Contact Reversing System
Places an invisible beam across door opening, that reverses
the door during down travel to the fully open position if
anything passes through beam .

Safe-T-Reverse® Contact Reversing System

Automatically stops and reverses a closing door within 2
seconds of contact with an object .

Safe-T-Stop® Timed Reversed System

Automatically opens a closing door, if door does not close
within 30 seconds .

ForceGuard® Control

Used to set the force required for opening and closing
door . For maximum safety, set the minimum force required
to fully open and close door .

Automatic Lighting System

Light bulbs up to 60 Watts max . , used for safer entries and
exits . The lights turn on when door is activated and
automatically turn off 4 .5 minutes later .

Manual Emergency Release

Allows the garage door to be opened or closed manually
for emergencies or maintenance .

IMPORTANT INSTALLATION

INSTRUCTIONS

1 READ AND FOLLOW ALL SAFETY, INSTALL ATION AND

OPERATION INSTRUCTIONS . If you have any

questions or do not understand an instruction, call

your authorized Genie installation professional .

2 Do Not install operator on an improperly balanced

door . An improperly balanced door could cause

severe injury . Repairs and adjustments to cables,

spring assembly, and other hardware must be made

by a trained service person using proper tools and

instructions .

3 Remove all ropes, and disable all locks connected to

the door before installing operator .

4 Install door operator 7 feet or more above the floor .

Mount the emergency release knob 6 feet above

the floor .

5 Do Not connect the operator to the source of power

until instructed to do so .

6 Locate the control button:

• Within sight of door.

• At a minimum height of 5 feet, so small children

cannot reach it .

• Away from all moving parts of the door.

7 Install the entrapment WARNING label next to the

wall button or console . Install the emergency release

tag on, or next to, the emergency release

8 The operator must reverse when the door contacts a

1-1/2 inch high object on the floor at the center of

the doorway . This is about the size of a 2” x 4” board

laid flat .

ReduCe

the

RiSk

SeVeRe

injuRy

death

WARNING:

afety

eatuReS

For Help, call 1-800-35-GENIE or visit www.geniecompany.com

Figure 2 Note Door Type

eaSuRe

aRaGe

ooR

eiGht

A Measure door height (floor to top of door) using a tape measure .
B This new Garage Door Opener is designed for doors up to and

including 7’ 6” tall . If door height is 7’ 6” or less continue to Check Step 4 .
C

If door height is 8’-0”, you need a Rail Extension Kit . (Figure 3) .

(See Accessories Order Form, Page 14) .
D If the door height is taller than 8’-0”, the opener you purchased is

the wrong version . Contact your Customer Service Representative

at 1-800-354-3643 .

Check Step 3:

-i

nStallation

heCkliSt

This Opener includes parts and supplies needed to install in most

garages and connect to most garage doors . There are many variations

of garages and garage doors . A few additional parts and supplies may

be needed to install Opener into your garage and connect to your

garage door . While checking items listed below, note any additional

items you will need .

Tools used in this section:

• 12’+ Tape Measure • Pencil • Ladder • Level

Check following items before assembling Opener:

heCk

ooR

ondition

and

hiCkneSS

Check Step 1:

heCk

aRaGe

ooR

liGnment

, o

peRation

and

alanCe

Check Step 2:

WARNING:

If your door sticks, binds, or is out of balance, have it adjusted

by a Genie Factory Authorized Dealer . Door springs, cables,

pulleys, brackets and associated hardware are under extreme

tension and can cause serious injury or death .

KEEP FEET CLEAR OF DOOR

3’ - 4’

Sectional

Door

3’ - 4’

Figure 1 Checking door balance

One-Piece

Door

Torsion
Springs

Extension
Springs

Center

Stile

Center Stile

Header Area

Figure 3 Rail Extension Kit

Rail Extension for

8’ door

Check condition of vertical stile in center of door, and its connection to

door’s top and bottom beams . (Figure 2)
A If door frame is nailed together and not a solid connection, door

frame must be braced or reinforced before installing Opener .
B If door is “lightweight” (made with frame and skin - not solid),

door (including door frame) must be braced or reinforced before

installing Opener .
C A door opener reinforcement bracket may also be needed to

connect garage door to Opener’s Door Bracket . This Opener is

designed for installation on a properly braced sectional door or

solidly braced one-piece door .
D Contact your Genie Factory Authorized Dealer or dealer of your

garage door for any necessary bracing and a door opener

reinforcement bracket (if needed) before proceeding .
E

If you have a wooden door, measure door’s thickness . If your door

is less than 2” thick, brace door or use shorter Door Bracket Lag Screws

(1/4” x 1-1/4” – not included)

A Raise door, check alignment and see if it moves freely (Figure 1) .

If door appears out of alignment, binds, or does not move smoothly,

contact a Genie Factory Authorized Dealer or dealer of your garage

door for repairs and adjustments to door mechanism .
B Raise door to 3’ – 4’ above ground and carefully let go . Door

should stay stationary . Slight movement is acceptable . More than

slight movement means door is out of balance . Contact a Genie

Factory Authorized Dealer or dealer of your garage

door for repairs and adjustments to door mechanism .

Check door type . Make a note of whether it is a sectional or a one-

piece door for reference later (Figure 2) .

B Find Header Bracket mounting height (Figure 4): (Do not attach

Header Bracket) .

•

Raise door, watching top edge of door and stop door

when its edge reaches its highest point .

•

Measure distance (“H”) from top edge of door to floor .

–

For sectional doors, add 1” to “H” . Mark a point

on center line . Bottom of Header Bracket will be

installed here .

–

For one-piece doors, add 7” to “H” . Mark this point on

center line . Bottom of Header Bracket will be

installed here .

heCk

ooR

eadeR

Rea

A Find vertical center line of door and header:

•

Close door .

•

Measure door width at top .

•

Mark a point at center of door and on header directly

above door . Draw a center line to connect points .

Check Step 4:

NOTE

The header is a heavily reinforced section of the wall just

above the top of the garage door opening .

Figure 4 Find Highest Point of Travel

SECTIONAL DOOR

ONE-PIECE DOOR

HEADER

Check wall for a stud or a solid header at your mark: (If checking a

finished wall, a stud finder may be helpful) .

•

If location is above Header, a 2” x 6” board must be

screwed to studs beside your mark with at least two Lag

Screws and Flat Washers (not provided) .

•

Transfer your mark to new mounting board .

Check ceiling or space above where Opener Power Head will be
mounted (Figure 5): There must be a 120 Volt grounded outlet or
wiring box within 3 feet of Power Head .

A The measurements above are taken from the garage door
centerline toward the rear of the garage .
B Find location of ceiling joist or truss above where Opener Power
Head will be and estimate type and quantity of materials needed for
your installation (Figure 6A & B) .

For Help, call 1-800-35-GENIE or visit www.geniecompany.com

WARNING:

Door springs are under extremely high tension and

should be handled ONLY by a trained professional .

NOTE

• For all types and styles of doors:

– If the ceiling in your garage is so low that there is

not at least a 3” space above the Header Bracket

mounting point, contact a Genie Factory

Authorized Dealer .

• If a door spring is in the way, place the Header Bracket

above the spring . Do Not move the door spring .

heCk

oweR

ead

ountinG

Rea

Check Step 5:

Door Center Line

Figure 5 Check Power Head location

11’

Figure 6B

FINISHED CEILINGS

Locate ceiling joists or trusses using

a stud finder or similar device .
Attach angle iron(not included) to

joists or trusses through finish

material using Lag Screws .

MOUNTING EXAMPLES

Perforated Straps

Conduit

Perforated Angle Iron

Wood

heCk

eilinG

foR

Rounded

oweR

ouRCe

Check Step 6:

NOTE

Permanent wiring must be installed by a Licensed

Electrician . Not all Genie Factory Authorized Dealers

are Licensed Electrician’s . Contact someone who is a

Licensed Electrician .

WARNING:

Do Not use an extension cord! Extension cords can

cause dangerous overheating conditions .

Do Not use portable generator! This product is

designed to operate using standard house current . Do

Not use alternate power supplies,

A Check that there is a 15 Amp 120 Volt grounded electrical

outlet or grounded permanent wiring box (per building code)

within 3’ of Opener Power Head: Figure 5

•

If not, an outlet or wiring box must be installed . Contact

a licensed electrician for installation .

•

If building codes require permanent wiring, Power Head

must be partially disassembled to install appropriate

wiring in place of Power Cord . (See Assembly and

Installation Poster .)

heCk

afe

-t-b

eam

ountinG

RaCket

oCation

Check Step 7:

Check for wood garage frame, jamb, or masonry at mounting
location (6” above floor) with attachment tabs facing away
from garage door (Figure 7) .

A If you cannot mount Safe-T-Beam® Mounting Bracket to
wood frame:

•

Concrete screws and concrete anchors (not included)

must be used to mount Brackets on masonry with

attachment tabs facing away from garage door .

Source

Sensor

Safe-T-Beam®

Mounting Bracket

Top of

Bracket

6” above

floor

Figure 7 Mounting

Safe-T-Beam®

Components

Grounded

outlet

10’

(7’-6” door)

(8’ door)

Figure 6A

OPEN CEILINGS Straps and angle iron may attach directly to joists

or trusses .

For Help, call 1-800-35-GENIE or visit www.geniecompany.com

Figure 8 Recommended Tools

Go to Assembly and Installation Poster for full
Installation Instructions.

eCommended

toolS

A Tools (Figure 8):
B Additional tools to make installation easier:

•

Slotted and phillips screw-driver bits

•

Stud finder

•

Sheet-metal cutting snips

Check Step 8:

emoVe

xiStinG

aRaGe

ooR

oCkS

Check that the garage door locks, rope, and T-Handles are
removed from the garage door before starting the installation .
A  If your garage does not have a separate entry door, it is
highly recommended to install a Genie Emergency Release
Kit (GER-2) .   Emergency Release Kit lets you open the garage
door from outside if there is a ppower failure .  (Please see
Accessories Order  Form on page 14 .)

Check Step 9:

Before going further, get any items and tools if needed
for your installation

Garage door frame reinforcement brackets, screws, bracing

or reinforcement kits (dealer)

Lag Screws (1-1/4”) for a wood door less than 2” thick (store)

Electrical outlet and/or wiring (supplied by a licensed electrician)

Sufficient angle iron or strapping for hanging Power Head (store)

60 Watt light bulbs (Rough service bulbs recommended)(store)

GER-2 Emergency Release Kit for entry during power failure (store)

Wood for header, ceiling, and/or door braces (store)

Masonry fasteners for Safe-T-Beam® Bracket installation (store)

Safe-T-Beam® Bracket Extensions (dealer)

Masonry drill bit (store)

Extension Kit (for 8’ Garage Doors)(dealer)

WARNING:

TO REDUCE THE RISK OF

SEVERE INJURY OR DEATH

IMPORTANT

SAFETY INSTRUCTIONS

1 READ AND FOLLOW ALL INSTRUCTIONS .
2 Never let children operate or play with the Door Controls . Keep

the Remote Control away from children .

3 Always keep the moving door in sight and away from people and

objects until the door is completely closed .

NO ONE SHOULD CROSS THE PATH OF A MOVING DOOR .

4 NEVER GO UNDER A STOPPED, PARTIALLY OPEN DOOR .
5 Test Opener monthly . The door MUST reverse on contact with

a 1-1/2” high object (or a 2” x 4” board laid flat) at the center of the

doorway on the floor . After adjusting either the Force or the Limit

of travel, retest the Door Opener . Failure to adjust the Opener

properly may cause severe injury or death .

6 When possible use the Emergency Release only when the door

is closed . Use caution when using this Release with door open .

Weak or broken springs are capable of increasing the rate of door

closure and increasing the risk of severe injury or death .

7 KEEP GARAGE DOORS PROPERLY BALANCED . See Owner’s

Manual . An improperly balanced door increases the risk of severe

injury or death . Have a Genie Factory Authorized Dealer make

repairs to cables, spring assemblies, and other hardware .

SAVE THESE INSTRUCTIONS.

noteS, RemindeRS

For Help, call 1-800-35-GENIE or visit www.geniecompany.com

djuStinG

imit

witCheS

and

oRCe

ontRolS

Adjustment 1:

A CLOSE ADJUSTMENT

•

On front panel of Power Head find adjusting screw

marked “CLOSE” (Figure MA-1) .

•

Gently turn screw counterclockwise until it stops .

–

Very little force is required to turn adjusting screw .

•

Press Wall Console to close garage door .

–

Observe if door stops at “CLOSE” limit switch .

(Figure MA-2) . If door is fully closed—adjustment is

finished . Go to “OPEN” Adjustment .

–

If door stops but is not fully closed,

a . Measure distance between bottom of door

and floor .

b . Move “CLOSE” Limit Switch that same distance

toward door .

–

If door stops and/or reverses before reaching the

“CLOSE” Limit Switch

a . Slightly increase CLOSE Force setting (clockwise) .

–

If door reverses after contacting floor, move Limit

Switch toward Power Head .

–

If door fails to move, check Safe-T-Beam® System .

See Troubleshooting Section, pages 10-11 .

•

Tighten Limit Switch Set Screw . Do not over-tighten

(strip) Limit Switch Set Screw .

B OPEN ADJUSTMENT

•

On front panel of Power Head find adjusting screw

marked “OPEN” (Figure MA-1) .

•

Gently turn screw counterclockwise until it stops .

–

Very little force is required to turn adjusting screw .

•

Press Wall Console to close garage door .

–

Observe if door stops at “OPEN” limit switch .

(Figure MA-2) . If door is fully open—adjustment

is finished .

–

If door stops but is not fully open,

a . Measure distance between bottom of door

top of door opening .

b . Move “OPEN” Limit Switch that same distance

toward Power Head .

–

If door stops before reaching the “OPEN”

Limit Switch

a . Slightly increase OPEN Force setting (clockwise) .

–

If door fails to move, see Troubleshooting Section,

pages 10-11 .

•

Tighten Limit Switch Set Screw . Do not over-tighten

(strip) Limit Switch Set Screw .

C Run Door Opener

•

Cycle opener a few times to double check settings .

Repeat adjustment steps as necessary .

WARNING:

•  A moving garage door can cause serious injury or death.
•  Keep the path clear.
•  Position the ladder to the side of the Power Head so it is

clear of all moving parts of the Opener and the door .

• Set the door Opener to use the minimum force needed

to open the door .

NOTE

• Little effort is required to turn the Force

Adjusting Knobs .

• If the door stops moving while opening or

closing, adjust the Open Force or Close Force

Controls slightly clockwise (to slightly

increase the force) and retry the step .

• The Open Force and Close Force Controls are to

be set to the minimum force necessary to

ensure the door smoothly opens and

closes completely .

• Ensure the Carriage Assembly is engaged and is

between the two Limit Switches before

operating the Opener .

Figure MA-1 Making Force Adjustments

OPEN

CLOS

OPEN

FORCE

CONTROLS

aintenanCe

and

djuStmentS

Figure MA-2 Making Force Adjustments

OPEN

For Help, call 1-800-35-GENIE or visit www.geniecompany.com

A To program one Button of a Remote Control (Figure MA-4):

•

Locate Learn Button and Learn Indicator Light

on left side of Power Head (Figure MA-5) .

•

Press and release Learn Button . Red Learn

Indicator Light will blink 2 times per second .

•

Press Remote Control Button once within 30

seconds . Red Learn Indicator Light will stay lit .

•

Press Remote Control Button again . Red Learn

Indicator Light will go out, indicating that

memory is stored .

B Program each additional Remote using step A above

(up to seven) .

NOTE

• Each Remote Control must be programmed

separately .

• The Remote Controls will not cause the door

Opener to close the garage door if the Safe-T-

Beam® System is malfunctioning .

• When programming the Remote Controls, they

must be at least 24” from the Antenna Wire .

• If the red Learn Indicator Light blinks

approximately 4 times per second,

programming has stopped . If programming

has stopped, repeat the above steps .

• Each Button on a 2 or 3 Button Remote Control

is for a different Opener . You cannot use more

than one Button per Remote, per Opener .

• A maximum of seven Remote Controls or

Wireless Keypads can be stored into the

Receiver at one time . If a Remote Control

becomes lost, or if you want to delete a Remote

Control or Wireless Keypad, see “To Erase All

Receiver Memory .”

RoGRamminG

the

emote

ontRolS

Programming 1:

CCeSSoRieS

To Erase All Remotes from Power Head Memory

A Press and hold Learn Button on Power Head for 10

seconds or until Learn Indicator Light goes out .

Memory is erased:

•

Program Transmitter/Receiver again as needed .

To Replace Remote Control Battery

A FOR NON-FLASHLIGHT MODELS

•

Pop off the back of the transmitter .

–

Use coin, pen, screwdriver or any similar device .

–

Replace old Battery with new coin type battery .

•

Replace back of remote.

B FOR FLASHLIGHT MODELS

•

Slide open battery cover .

–

Replace old Battery with new AAA battery .

•

Replace battery cover.

A Open garage door using

Wall Console .

B Lay a 2” x 4” board flat in center

of doorway .

C Close door using Wall Console .
D Check that door stops and reverses

within 2 seconds after it

contacts board:

•

If door does not reverse, decrease

Close Force until door reverses .

•

If door still does not reverse,

move Limit Switch toward door .

E Check Safe-T-Beam® System

operation:

•

If beam is blocked, door will

not close .

NOTE

The door must contact the 2” x 4” board before the Carriage activates

the Close Limit Switch . If not, readjust the Close Limit Switch .

ettinG

ontaCt

eVeRSe

unCtion

Adjustment 2:

NOTE

Limit Switch and Force Adjustments must be completed

before checking the contact reverse function (Figure MA-3) .

2” x 4” board

laid flat

Figure MA-3

Transmitter Compliance Statement

For Help, call 1-800-35-GENIE or visit www.geniecompany.com

Remote Control Operation

A Press Button on Remote Control . Garage door will move .
B Press Button again . Garage door will stop:

•

The door automatically stops at the end of the open or

close cycle .

C Press Button again . Garage door will reverse .

WARNING:

A moving garage door may cause serious injury or death .
•  Keep people clear of opening while door is moving .
•  Do not allow children to play with the Remote Controls .
If the Safety Reverse does not work properly:
•  Close the door and disconnect the Opener using the

Emergency Release Cord .

• Do not use the door Opener, Remote Controls, or

Wireless Keypad .

• Refer to the door and door Opener Owner’s Manuals

before attempting any repairs .

1 2 3 4

Figure 13 Learn Code Button and Indicator Light

Figure MA-5 Learn Code Button and Indicator Light

1 Button Compact Remote

w/Docking Station

Figure MA-4 Genie Remote Controls

3 Button Compact Remote

w/Docking Station

A Install two 60 Watt light bulbs (not included) into Light
Sockets (Figure MA-6):

• Rough service, 130 Volt bulbs are recommended .

B Hold the lens, with the bottom hinges pointing up, against
the power head metal front cover (Figure MA-7) .

• Insert (2) #8-32 x 3/8” Phillips Hex Head Screws

through the Bottom hinges and into holes provided

in metal front cover of Power Head (Figure MA-7) .

Tighten screws .

• Flip Lens up and fasten with (2) #8-32 x 3/8” Phillips Pan

Head Screws where indicated .

Figure MA-7

Figure MA-6

nStall

iGht

ulbS

and

enS

WARNING:

Use the Wall Console included with Opener . Any

other wall console can cause the Opener to operate

unexpectedly and the light to stop working .

To program a Homelink® or Car2U Device:
(This GDO is Homelink® and Car2U compatible)

• Follow the Homelink® or Car2U instructions in your car

owner’s manual .

For Help, call 1-800-35-GENIE or visit www.geniecompany.com

A Monthly:

• Door springs and door hardware:

– Oil door roller, bearings, and hinges using silicone

lubricant or light oil .

• Balance Door .

– Close door .

– Release Carriage Assembly from Rail Assembly by pulling

the Emergency Release Knob towards the door .

– Raise door manually 3’- 4’ and verify that door stays at

that position . See Check Step 2 on page 4 .

– Reattach Carriage Assembly to Rail Assembly:

a . Pull the Emergency Release Knob toward

Power Head .

b . Close door .

• Contact Reverse Test.

– Perform Adjustment 2 on page 8 .

NOTE

When the door is 3’ - 4’ above the ground, the door

should stay open . Slight movement is acceptable . If

the door moves too much, contact a Genie Factory

Authorized Dealer for service or call Customer Service at

1-800-35-GENIE.

WARNING:

Do not operate door automatically or manually if springs

are broken . Contact a Genie Factory Authorized Dealer for

service or call Customer Service at 1-800-35-GENIE .

If the door fails to reverse on contact with the board,

adjust the Close Force Control as specified in Set Limit

Switches and Force Controls on page 7 & 8 . If the Opener

still fails, contact a Genie Factory Authorized Dealer for

service or call Customer Service at 1-800-35-GENIE .

NOTE

Use ONLY Genie Lubricant (GLU-3) . Other lubricants

may damage the Opener .

FCC AND IC CERTIFIED

All devices comply with Part 15 of the FCC Rules .

Operation is subject to the following two conditions: (1)

this device may not cause harmful interference, and (2)

this device must accept any interference received, includ-

ing interference that may cause undesired operation .

GLU-3
Lubricant

MAINTENANCE

B Yearly:
• Wipe off old excess lubricant from Drive Screw .

• Lubricate Drive Screw with Genie Lubricant (GLU-3)

C As needed
• Replace lightbulbs. (See page 9)

Safe-T-Beam® System Self-Diagnostic Troubleshooting

Source (Red LED)

Sensor (Green LED)

Possible Problem

Solution

Normal operation

None required

OFF

• Power Head not powered

• Check breakers, fuses, plugs

• Wiring from Power Head bad

• Check wiring for obvious shorts

OFF

• Wiring to Source missing or bad • Check wiring

• Power has been interrupted

• Remove power and reapply

2 BLINKS, Pause

• Beam not aligned

• Check Source, Sensor alignment

(Repeat)

• Beam obstructed

• Check for obstruction

• Sensor defective

• Contact Customer Service

2 BLINKS, Pause

• Wire to Sensor missing or bad

• Check wiring

(Repeat)

OFF

• Sensor defective

• Contact Customer Service

3 BLINKS, Pause

• Sensor receiving interference

• Determine source of interference

(Repeat)

• Check for interference from sun-

light or a source unit on an

adjacent door

• Contact Customer Service

4 BLINKS, Pause

• Source not sending pulses

• Contact Customer Service

(Repeat)

• Source defective

• Contact Customer Service

TROUBLESHOOTING

WARNING:

For Help, call 1-800-35-GENIE or visit www.geniecompany.com

General Troubleshooting

Problem

What To Do

Opener does not run

1 . Check Lock switch on Wall Control (see Wall Console section on Installation Poster) .

from Wall Control

2 . Check Power Source:

• For Grounded Plug Connection .

– Plug a lamp into the electrical outlet used for the door opener .

a . If lamp lights, power source is good .

b . If lamp does not light, check fuse or circuit breaker .

• For Permanent Wiring Connection .

– Check fuse or circuit breaker .

3 . Check connections (see Wall Console section on Installation Poster):

• At Power Head Terminals and Wall Control .

Door Opener starts

1 . Check Wires to ensure that they are not cut (Stapes can cut insulation and short Wires)

for no apparent reason

Replace any shorting Staples and shorted Wires .

2 . Was Remote Control lost or stolen? If so, erase all Remote Control codes from Receiver’s memory

and reprogram for remaining remote controls . (See Erase All Receiver Memory on page 11) .

3 . Ensure that no Buttons are stuck “pushed-in” on Wall Console or any Remote Controls .

Door starts down, then

1 . Check Close Limit Switch setting (page 7 and Installation Poster) . Adjust as needed .

stops before it is

2 . Check Force Setting (page 7 & 8) . Adjust as needed .

completely closed

3 . Check for shorted wires .

Door starts down, then

1 . If a new installation, check Door Arm position .

stops and goes back up

2 . Check operation of Contact Reverse function .

3 . Check Safe-T-Beam® System for beam obstruction or misalignment of Lenses .

4 . Check Safe-T-Beam® System diagnostic code .

5 . Check Close Force adjustment (see Set Limit Switches and Force Controls on page 7 ) . Adjust as needed .

6 . Check garage door for binding .

Door will only run closed

1 . Check Open Limit Switch for a short circuit and for proper wiring .

2 . Check Open Force adjustment (see Set Limit Switches and Force Controls on page 7 & 8) . Adjust as needed .

3 . Check condition of garage door and door spring(s) .

4 . WARNING: If you suspect a problem with the garage door hardware or springs, contact a Genie

Factory Authorized Dealer for service, or contact Customer Service at 1-800-35-GENIE .

5 . Check position of Lock Switch on Console .

Door will only run open

1 . Check Safe-T-Beam® System as detailed in the Safe-T-Beam® System Self-diagnostic Troubleshooting Chart

(page 10) .

2 . Check Close Limit Switch for a short circuit and for proper wiring .

3 . Check Close Force adjustment (see Set Limit Switches and Force Controls on page 7 & 8) . Adjust as needed .

Lights will not turn off

1 . Disconnect Wires connecting Wall Console to Power Head (see “Wall Console Installation”- on Installation post-

er) .

Check their condition and either replace or reconnect .

2 . Until a replacement Wall Console can be obtained, disconnect Wall Console and use only Remote Controls

or Wireless Keypad to operate Opener .

3 . Check for non-compatible wall control .

Door starts up, but stops

1 . Check (ensure) that garage door and Opener are in good repair, properly lubricated, and properly

before it is

balanced as detailed in Maintenance Section .

completely open

2 . WARNING: If you suspect a problem with the garage door hardware or springs, contact a Genie Factory

Authorized Dealer for service, or contact Customer Service at 1-800-35-GENIE .

3 . Check Open Limit Switch for a short circuit and for proper wiring .

4 . Check Open Force adjustment (see Set Limit Switches and Force Controls on page 7 & 8) . Adjust as needed .

Operator runs, but door

1 . Ensure Carriage Assembly is engaged to Rail Drive Screw (see Install Carriage Assembly -INSTALLATION POSTER) .

does not move

2 . Check Force adjustment (see Set Limit Switches and Force Controls on page 7) . Adjust as needed .

3 . Check that all sections of Rail Drive Screw are turning when Motor runs . If not:

• Check condition (not cracked, split, or broken) and placement of Coupler. Replace as needed.

• Check condition (not cracked, split, or broken) and placement of Collar and Clip. Replace them

as needed .

Wall Console Vacation

1 . Ensure Carriage Assembly is in contact with Close Limit Switch .

Lock function does

2 . Check when door is fully closed, that Carriage activates Close Limit Switch . If not, adjust position of Close

not work

Limit Switch (See page7) .

Noisy Operation

1 . Be sure all fasteners are tight .

2 . Check (ensure) that garage door and Opener are in good repair, properly lubricated, and properly

balanced as described in Maintenance Section (page 10) .

For Help, call 1-800-35-GENIE or visit www.geniecompany.com

Opening Cover May Cause Electric Shock

iRinG

iaGRam

10 11 12

10 11 12 13 14 15 16 17

BLACK

ORANGE

OPEN

YELLOW

WHITE

STRIPED

BLACK

PURPLE

GREEN

BLUE

RED / WHITE

RED

GREY

BROW

ORANGE

GREEN

OPEN

LIGHTS

WHITE

GREEN

POWER CORD

PRIMARY

SEQUENCER

MOTOR

RPM

SENSOR

WALL

CONTROL

RADIO CONNECTOR

STB

SYSTEM

TERMINAL

STRIP

MOTOR

CAPACITOR

THERMAL

PROTECTOR

PRIMARY

SECONDARY

TRANSFORMER

SEQUENCER

HOUSING

(Vcc)

(SIGNAL)

(Vcc)

(TRIP)

(STB SYSTEM

)

(COMMAND)

)

(

Power Head Assembly

[1]

aRtS

dentifiCation

Item Part Name
1 Power Head Assembly

A Cover (by Series Model)

B Front Plate Assembly

C Light Socket

D Motor Parts

E Receiver Assembly

F Capacitor (By Series/Model)

G Opto Wheel

H Opto-Luctor Assembly

J Sequencer Assembly

K Circuit Board Bracket

L Transformer

M Terminal Strip

N No . 8-32 x 1/2” Hex Head Screw

w/Lockwasher

P No . 8-32 x 3/8” Slot Hex Head

Screw w/Lockwasher

R Capacitor Isolator

4 1/4-20 Shoulder Bolt

5 1/4” Flange Nut

39 Coupler

41 No . 8-32 x 3/8” Phillips

Hex Head Screw

42 No . 8-32 x 3/8” Phillips

Pan Head Screw

48 Mounting Straps

49 Light Lens

Power Head Parts List

oweR

ead

Number

Included

WARNING:

For Help, call 1-800-35-GENIE or visit www.geniecompany.com

15B

15A

ail

aRtS

dentifiCation

Item Part Name
1 Power Head Assembly (see page 5)

3 Rail Assembly (3-piece)

3A First Rail Section

3B Middle Rail Section

3C End Rail Section

4 1/4”-20 Hex Head Shoulder Bolt

5 1/4”-20 Hex Flange Nut

6 Carriage Stop

7 Rail Clamps

8 5/16” Hex Head Shoulder Bolt

9 5/16” Hex Flange Nut

10 Carriage Assembly

11 Collar

12 Retaining Clip

13 Rail Strap

15A Open Limit Switch Assembly (grey)

15B Close Limit Switch Assembly (brown)

16 #8-32 x 3/8” Hex Head Screw

17 Emergency Release Cord

18 Emergency Release Knob

19 Emergency Release Tag (not shown)

20 Header Bracket

21 Door Bracket

22 1/4” x 2” Lag Screw

23 Straight Door Arm

24 Clevis Pin

25 Cotter Pin

26 Curved Door Arm

27 3/8” x 7/8” Hex Head Bolt

28 3/8” Hex Flange Nut

Parts List

(cont’)

Number

Included

Item Part Name
29 Wire (not shown)

95 ft

30 Insulated Staples (not shown)

31 Wall Button (not shown)

varies

33 Wall Console (not shown)

varies

35 Entrapment WARNING Label (not shown)

36 Safe-T-Beam (STB)Sensor (green LED)

(not shown

37 Safe-T-Beam Source (red LED)

(not shown)

38 Safe-T-Beam Bracket (not shown)

39 Coupler

40 #10 x 1-1/4” Phillips Hex Head Screw

43 Safety and Maintenance Guide

(not shown)

44 Wire Clip

46 5/16” x 3/4” Hex Head Bolt

47 1/4”-20 x 3/4” Self-tapping Screw

48 Mounting Straps

49 Light Lens (see page 5)

50 Remote Control (not shown)

varies

Number

Included

Parts List

(cont’)

Rail Assembly

[3]

For Help, call 1-800-35-GENIE or visit www.geniecompany.com

No C .O .D . shipments . Please include check or money

order, made payable to The Genie Company . Do not send

cash . Allow 3-4 weeks for delivery .

1-800-354-3643 . Please have part number and credit

card ready . Mail Order Form to: Genie Company, 22790

Lake Park Blvd, Alliance, Ohio 44601 . We accept Visa or

Mastercard on phone orders only .

Please add local sales tax if you reside in one of the states listed .
California, Connecticut, Florida, Georgia, Illinois, Indiana, Maryland,
Massachusetts, Michigan, New Jersey, New York, Ohio, Tennessee,
Virginia, Wisconsin

TOTAL ORDER

SHIPPING & HANDLING

$ 5 .00

STATE SALES TAX

GRAND TOTAL

Pas d’expédition contre remboursement . Veuillez inclure un chèque

ou un mandat bancaire, le payable fait à The Genie Company .

N’envoyez pas d’argent comptant . Accordez de 3 à 4 semaines

pour la livraison . 1-800-354-3643 . Ayez sous la main le numéro de la

pièce et celui de la carte de crédit . Mettre à la poste le arrngement

à: Genie Company, 22790 Lake Park Blvd, Alliance, Ohio 44601 . Nous

acceptons les commandes par téléphone avec paiement par carte

de crédit Visa ou Mastercard .

Veuillez indiquer les taxes de vente locales si vous résidez dans l’un des états
répertoriés ci-dessous .

COMMANDE TOTALE

MANUTENTION ET EXPÉDITION

$ 5 .00

TAXE DE VENTE

TOTAL GLOBAL

No se aceptan pedidos de pago contra entrega (COD) .

Sírvase incluir su cheque o giro postal, la cuenta pagadera

hecha aThe Genie Company . No envíe dinero en efectivo .

Concédanos 3 a 4 semanas para la entrega . 1-800-354-3643 .

Sírvase tener listos los números del modelo y de la tarjeta

de crédito . Enviar hacer un pedido de mercancia a: Genie

Company, 22790 Lake Park Blvd, Alliance, Ohio 44601 .

Aceptamos pedidos telefónicos de Visa o Mastercard .

Sírvase agregar el impuesto de ventas local si usted reside en uno de los
siguientes estados:

Ordering Instructions

Las Instrucciones que Ordenan

Instructions Commandant

(GI CT390-1)

1-Button Compact Remote - Allows remote operation of garage door .

Comprima el Mando de Distancia - Proporciónar operación remoto de la puerta del garaje .

Télécommande compacte - Permettre opération éloign´´de porte de garage .

(GI CT390-3)

3-Button Compact Remote - Allows remote operation of 3 garage doors .

De 3 botones Comprima el Mando de Distancia - Proporciónar operación remoto de tres las puertas del garaje .

3-boutenner la Télécommande compacte - Permettre opération éloign´ trois portes

de garage .

(GWKPD)

Wireless Keypad - Operates Intellicode

Garage Door Openers without Remote Control or key .

Sistema de entrada por teclado numérico inalámbrico - Acciona los abridores de puertas de garaje Intellicode

sin

control remoto o llave .

Système d’ouvre-porte de garage à clavier sans fil - Actionne les ouvre-porte de garage avec Intellicode

sans

télécommande ni clé .

(GLU-3)

3/4 oz. Screw Drive Lubricant - Ensures proper equipment wear protection .

3/4 once Lubricante de tornillo accionar - Asegura componente correcto protección por deterioro .
La onza 3/4 Lubricant de la vis - Garantir componant exact par systéme défense vers user .

(GW-2)

Universal Wall Button - Provides additional convenient inside operation of door .

Botón de pared universal - Proporciona operación conveniente de la puerta desde el interior .
Bouton mural universel - Actionne l’ouvre-porte de l’intérieur du garage .

(GPS-5)

Perfect Stop

- Ensures perfect parking .

Stop Perfecto

- Asegura el estacionamiento perfecto .

Butoir Perfect Stop

- Permet de stationner à la perfection dans le garage .

(LCGX-8)

ChainLift Extension Kit - An Extension that increases the travel of an Opener to accommodate an

eight foot door .
Juego de extensión de cadena deslizable - Una extensión para aumentar la longitud de la baranda de Chain

Glide, para acomodar una puerta de 8 pies (2,43 m) .
Nécessaire de prolongement du coulisseau - Rallonge de prolongeant la course de l’ouvre-porte Chain Glide

pour une porte de 2,4 m (8 pi) de hauteur .

(60 WATT

) Enhanced/Rough Service Light Bulb - Ensures proper equipment compatability .

Bombilla de 60 Vatios - Asegura componente correcto de sistema .
éclairage de 60 WATT - Garantir componant exact par systéme .

(GER-2)

Emergency Release Kit - Provides access to garage from outside in the event of

an electrical power failure .

Juego de pica-porte de pestillo - Permitir entrtada desde por fuera de garaje porque corte

de eléctrico .

Nécessaires de Déclenchement de secours - Le nécessaire de déclenchement

de secours est conçupour vous permettre d’accéder à votre garage depuis

l’extérieur en cas de panne de courant et lorsqu’il .

STB

Adapter Brackets (2) - Used in conjunction with standard STB Brackets . They provide

additional clearance and mounting options .
El adaptador pone entre paréntesis (2) - Usado en unión con paréntesis uniformes de

montar de STB, ellos proporcionan el espacio libre adicional junto con mortar las opciones .

Crochets d’adaptateur (2) - Utilisé conjointement avec STB standard monter les crochets,

ils fournissent le dégagement supplémentaire avec monter d’options .

(GSX-8)

DirectLift Extension Kit - An Extension to increase travel of an Operator to accommodate

eight foot door .
Juego de extensión deslizante de Screw Drive - Una extensión para aumentar la carrera de un abridor

deslizable, para acomodar una puerta de 8 pies (2,43 m .) .
Nécessaire de rallonge du Screw Drive - Rallonge de prolongeant la

coursede l’ouvre-porte pour une porte de 2,4 m (8 pi) de hauteur .(GIRU-1T)

SHIP ORDER TO:
ENVIAR MERCANCIA CON:
EXPÉDIER MARCHANDISE POUR:

NAME / NOMBRE / NOM

ADDRESS / DIRECCIóN / ADRESSE

CITY / CIUDAD / VILLE

STATE / ESTADO / ÉTAT

ZIP / CóDIGO POSTAL / CODE POSTAL

California, Connecticut, Florida, Georgia, Illinois, Indiana, Maryland,
Massachusetts, Michigan, New Jersey, New York, Ohio, Tennessee,
Virginia, Wisconsin

How many?

¿Quántos?

$36.50

$50.00

$35.00

$50.00

$5.00

$3.75

$4.00

$32.00

$2.73

$20.00

$4.37

P/N 36248R

P/N 36223R

P/N 35661R

P/N 35691R

P/N 35218A.S

P/N 35693R

P/N 35677R

P/N 35679R

P/N 35678R

(GWC-2W)

Deluxe Wall Console - Operates Garage Door . Independent light control . Security vacation lock .

Consola de lujo de pared - Acciona la puerta del garaje . Control de luz independiente . Cerradura de

seguridad para vacaciones .

La Console dse luxe de Mur - Actionne la porte de garage . Commande d’éclairage indépendante .

Interrupteur de verrouillage de sécurité .

P/N 26210A.S

P/N 35675R

(Prices subject to change without notice)

(Valoran el cambio con sujeción a sin nota)

(Les prix assujettissent pour changer sans la notification)

P/N 34439R.S

(GABX8)

QuietLift Extension Kit - An Extension that increases the travel of an Opener to accommodate an

eight foot door .
Juego de extensión de cadena deslizable - Una extensión para aumentar la longitud de la baranda de Chain

Glide, para acomodar una puerta de 8 pies (2,43 m) .
Nécessaire de prolongement du coulisseau - Rallonge de prolongeant la course de l’ouvre-porte Chain Glide

pour une porte de 2,4 m (8 pi) de hauteur .

$32.00

P/N 35663R

Garage Door Opener Accessories Order Form

Formulario de pedido de accesorios para abridores de puertas de garaje

Formulaire de commande des accessoires pour ouvre-porte de garage

For additional accessories not shown . visit our website at www .geniecompany .com

Para accesorios adicionalesno mostrada, visite nuestro sitio web en www .geniecompany .com

pour les accessoires supplémentaires pas montré, visiter notré site web à www .geniecompany .com

TOTAL DEL PEDIDO

FLETE Y MANEJO

$ 5 .00

IMPUESTO DE VENTAS ESTATAL

GRAN TOTAL

$45.00

P/N 35657R

(GI F TD-1)

1-Button Flashlight Transmitter - Remote Controller with a Flashlight .

1 abrocha transmisor de linterna - Director remoto con una linterna .

1-boutenner l’émetteur de lampe de poche - Le contrôleur éloigné avec de lampe de poche .

Ask a Question ?

PDF User Manual

DirectLift 3060 DirectLift Directlift 2060 Directlift plus 3060

Full Text Searchable PDF User Manual