Genie CCTV VRCD-5351 Instruction Manual - User Manual

Full Text Searchable PDF User Manual

Digital Day/Night Vandal Resistant Dome Camera

INFORMATION -

This equipment has been tested and found to comply with

limits for a Class A digital device, pursuant to part 15 of the FCC Rules & CE Rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.

WARNING -

Changes or modifications not expressly approved by the

manufacturer could void the user’s authority to operate the equipment.

CAUTION :

To prevent electric shock and risk of fire hazards:

◆

Do NOT use power sources other than those specified.

◆

Do NOT expose this appliance to rain or moisture.

This installation should be made by a qualified service person and

should conform to all local codes.

The lightning flash with an arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of uninsulated
dangerous voltage within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.

Digital Day/Night Vandal Resistant Dome Camera

Features

Horizontal Resolution of 540 TV
Lines

Clear image quality has been achieved by
employing a SONY CCD with 410,000
(effective) pixels, which provides a
horizontal resolution of 540 TV lines.

DAY & NIGHT

This camera has a function that auto-
matically selects the mode that is
appropriate for daytime or night-time
conditions. The COLOUR mode operates in
daytime conditions to provide optimum
colours, and BW mode operates in night-
time conditions to enhance the definition
of the image.

Electronic IRIS

The electronic IRIS function enables
continuous automatic control of the
shutter between 1/50~1/120,000 seconds.

PRIVACY Function

The PRIVACY function conceals the
areas not required to appear on
the image.

3 Axis built-in Vandal Resistant Dome
Housing

High Sensitivity

The built-in high sensitivity SONY COLOUR
CCD enables clear image even at 0.3Lux
(0.002Lux in Sense-up)

DNR (Digital Noise Reduction)

The amount of low illuminance noise
has been significantly reduced, and the
signal-to-noise ratio (S/N ratio) as well as
horizontal resolution have been improved,
resulting in clear and sharp images
displayed even in low light.

Controlled by OSD Menu

The camera functions are controlled by
selecting text displayed on the monitor
screen.

Additional Functions

SENS-UP, MOTION DETECTION,
MIRROR, SHARPNESS and SYNC
(INT/LL) functions are also available.

Heater for cold temperature (optional)

Weatherproof (IP66)

Digital Day/Night Vandal Resistant Dome Camera

Warning

The camera requires periodic inspection.

Contact an authorised technician to carry out the inspection.

Stop using your camera when you find it malfunctioning.

If the camera emits smoke or is unusually hot for a long period,
a fire may be caused.

Do not Install the camera on a surface that can not support it.

If the camera is installed on an inappropriate surface, it may fall
and cause injury.

Do not hold plug with wet hands.

It could cause an electric shock.

Do not dis-assemble the camera.

It may result in an electric shock or other hazards.

Do not use the camera close to a gas or oil leak.

It may result in a fire or other hazards.

Digital Day/Night Vandal Resistant Dome Camera

Contents

Features

Warnings and Precautions

Names and Functions of Parts

Dimensions

Installation

Cable Connections

Lens
OSD
VBS-EXTRA
3 Axis Bracket
SMPS

10
10

11
11
11

Components

Digital Day/Night Vandal Resistant Dome Camera

Camera Operation

Troubleshooting

Menu
Settings

• LENS (selection)
• SHUTTER (condition and speed control)
• WHITE BALANCE control
• BLC (Back Light Compensation)
• AGC (Auto Gain Control)
• DNR (Digital Noise Reduction)
• SENS-UP
• SPECIAL
• EXIT

14
15
16
18
19

20
21
22
23
24
29

Specifications

Digital Day/Night Vandal Resistant Dome Camera

Precautions

Do not install the camera in
extreme temperature conditions.

Do not install the camera under
unstable lighting conditions.

Do not touch the front lens of the
camera.

Only use the camera under conditions
where temperatures are between
-10

C and +50

C. Be especially

careful to provide ventilation when
operating under high temperatures.

It can cause the image quality to be
poor.

Severe lighting change or flicker can
cause the camera to work improperly.

This is one of the most important parts of
the camera. Be careful not to leave
fingerprints on the lens cover.

Do not install or use the camera in an
environment where the humidity is high.

Digital Day/Night Vandal Resistant Dome Camera

It can cause malfunctions to occur.

If it gets wet, wipe it dry immediately.
Liquids can contain minerals that
corrode the electronic components.

If exposed to radioactivity the CCD
will fail.

It can damage the CCD.

Do not drop the camera or protect
it from physical shocks.

Do not expose the camera to rain
or spill beverage on it.

Do not expose the camera to
radioactivity.

Never keep the camera pointed
directly at strong light.

Digital Day/Night Vandal Resistant Dome Camera

Components

1. COLOUR DOME CAMERA

2. SCREWS

4. WIRE FOR VBS-EXTRA

5. INSTRUCTION GUIDE

3. WRENCH

Digital Day/Night Vandal Resistant Dome Camera

Names and Functions of Parts

Digital Day/Night Vandal Resistant Dome Camera

OSD PCB

DOWN

SET

RIGHT

LEFT

●

SET button

: Used for the menu display. This button can be used to

confirm settings after changing the value of the selected function or
current conditions.

●

UP & DOWN buttons

: Used for selecting items by moving the cursor

up or down on the menu screen.

●

LEFT & RIGHT buttons

: Used when changing item values, by moving

the cursor to the left or right on the menu screen.

LENS : Vari-Focal DC Auto Iris Lens

(unit : mm)

Digital Day/Night Vandal Resistant Dome Camera

Names and Functions of Parts

Dimensions

VBS-EXTRA FOR CONNECTING TO SERVICE MONITOR

Please use the supplied wire when connecting to external monitor

3 AXIS BRACKET

Please loosen screws and fix in to tilted and panned position.

SMPS PCB FOR DUAL POWER - IF APPLICABLE

VBS-EXTRA

(unit : mm)

Digital Day/Night Vandal Resistant Dome Camera

Installation

CONDUIT

ENTRY

RUBBER

GASKET

BASE

HOUSING

No. 8-32

UNC

DECORATION

RING

M4*10

DOME COVER

Digital Day/Night Vandal Resistant Dome Camera

Cable Connections

1. Dome Base Mounting

- Open the dome cover by loosening the 3 screws, using the special

wrench provided.

- Mount the base of the camera to a sturdy surface using the 4 screws

(1.5 inch) and the 4 pre-made holes on the base of the dome.

2. Power Connect & Monitor Impedance

- DC12V/300mA regulated power supply (DC12V only)

or AC24V Class 2 power supply (for the AC24V/DC12V model)

- To avoid a fire or shock hazard, use a CE certified power supply.
- Set the monitor impedance switch to 75ohm. Check the impedance

switch if the screen becomes blurred.

3. Camera Module Adjustment

- Loosen the screws for the 3-axis camera bracket to adjust the angle

of view of the camera.

- Make sure to retighten the screws for camera bracket.
- Set up the required functions by using the OSD buttons.

4. Dome Cover Mounting

- Replace the dome cover to the base and tighten the 3 screws.

Digital Day/Night Vandal Resistant Dome Camera

Camera Operation

Menu

SETUP menu

LENS (selection)

SHUTTER
(condition and speed control)

WHITE BALANCE control

BACKLIGHT
(Backlight Compensation)

AGC (Auto Gain Control)

DNR
(Digital Noise Reduction)

SENS-UP (Low illuminance)

SPECIAL

EXIT

•

MANUAL

•

ESC

•

MANUAL

•

FLK

•

ATW

•

AWC

•

MANUAL

•

OFF

•

LOW

•

MIDDLE

•

HIGH

•

OFF

•

LOW

•

MIDDLE

•

HIGH

•

OFF

•

LOW

•

MIDDLE

•

HIGH

•

OFF

•

AUTO

•

CAMERA ID

•

COLOUR

•

SYNC

•

MOTION DETECTION

•

PRIVACY

•

MIRROR

•

SHARPNESS

•

RESET

•

RETURN

Digital Day/Night Vandal Resistant Dome Camera

Settings can be made using the 5 buttons located inside the camera.

1. Press the SET button

•

Settings can now be made. The SETUP menu is displayed on the monitor.

2. Select a menu item from the list available by using the UP and DOWN buttons.

•

The cursor can be moved up or down by using the UP and DOWN buttons.
Position the cursor to point to the function requiring adjustment.

Settings

DOWN

SET

RIGHT

LEFT

SETUP

LENS

SHUTTER

---

WHITE BAL.

ATW

BACKLIGHT

OFF

AGC

LOW

DNR

MIDDLE

SENS-UP

AUTO

SPECIAL
EXIT

Digital Day/Night Vandal Resistant Dome Camera

Camera Operation

SETUP

LENS

SHUTTER

---

WHITE BAL.

ATW

BACKLIGHT

OFF

AGC

LOW

DNR

MIDDLE

SENS-UP

AUTO

SPECIAL
EXIT

Modes can be changed

using the LEFT and

RIGHT buttons.

Select any function you

wish to operate by

using the UP and

DOWN buttons.

3. When the LEFT or RIGHT button is pressed, available values and modes are

displayed in order. Keep pressing the button until you get to the mode you wish to
select.

4. Select 'EXIT' and then press the SET button to exit the set up Menu.

This function is used to adjust the brightness of the screen.

1. When the SETUP menu is displayed on the screen, position the cursor to point

to 'LENS' by using the UP and DOWN buttons.

2. Select the type of the lens setting to use by pressing the LEFT or RIGHT button.

Note

• If appears at the mode you wish to operate, it means that there is a

sub-menu which can be selected by pressing the SET button.

• If appears at the mode item, it means that there is no mode

available to be selected.

LENS (selection)

SETUP

LENS

SHUTTER

---

WHITE BAL.

ATW

BACKLIGHT

OFF

Digital Day/Night Vandal Resistant Dome Camera

MANUAL

: Manual Lens selection

: Auto Iris Lens selection

3. Press the SET button if you wish to return to the previous menu

Note

• The brightness of the screen can be adjusted in DC mode. The brightness

can be adjusted within the range of 1 ~ 70. The optimum level of brightness
for the user can be achieved by adjustment.

• If you select the MANUAL mode, it can be adjusted in ESC mode.

Digital Day/Night Vandal Resistant Dome Camera

Auto or manual control can be selected.
1. When the SETUP menu is on the screen, position the cursor to point to

'SHUTTER' by using the UP and DOWN buttons.

2. Select the shutter mode by pressing the LEFT or RIGHT button.

FLK

: Select 'FLK' mode when flickering occurs on the screen

due to an imbalance between illumination and frequency.
NTSC Model:1/120, PAL Model: 1/100

ESC

: Auto control of the shutter speed is enabled.

When ESC mode is on, the shutter speed is controlled automatically

according to the brightness of the scene.

MANUAL

: The shutter speed can be controlled manually.

3. Select 'MANUAL' mode for manual shutter speed adjustment.

•

Selectable speeds are from ‘1/60’ to ‘1/120,000’sec (NTSC) and ‘1/50’

to ‘1/120,000’sec (PAL).

4. Press the SET button when the settings are completed.

Camera Operation

SHUTTER (condition and speed control)

SETUP

LENS

SHUTTER

ESC

WHITE BAL

ATW

BACKLIGHT

OFF

• While using the internal synchronous system, if the shutter setting is on

'ESC' and the camera is directly facing bright fluorescent lights the
image on the screen can be adversely affected - therefore choose
the installation location carefully.

• When 'MANUAL' mode is on, the SENS UP function cannot be used.

Note

Digital Day/Night Vandal Resistant Dome Camera

The screen colours can be adjusted using the WHITE BALANCE function.
1. Position the cursor to point to 'WHITE BAL' on the SETUP menu by using the

UP and DOWN buttons.

2. Select the mode you wish to adjust by pressing the LEFT or RIGHT buttons.

※ S

elect one of the 3 modes below.

ATW(Auto Tracking White Balance)

: This mode can be used within the colour

temperature range 1,800

K ~ 10,500

K (eg, fluorescent light, outdoor, sodium

vapour lamp etc.)

AWC(Auto White Balance Control)

: Press the SET button while the camera

is directed at a piece of white paper to obtain the optimum state under current
illumination. If the environment, including the light source, changes the white
balance will need to be adjusted again.

MANUAL

: The manual adjustment mode enables finer adjustment.

Select ATW or AWC first then change to manual adjustment mode and press
the SET button. Set the appropriate colour temperature then increase /
decrease the red and blue colour values and monitor the colour changes of
the object.

WHITE BALANCE control

• Under the following conditions the WHITE BALANCE function may not operate

properly. In such cases, please select the AWC mode.

When the object’s surroundings have a very high colour temperature

(eg, a clear sky and sunset)

When the object’s surroundings are dark
If the camera directly faces a fluorescent light or is installed in a place where
there are considerable changes in illumination, the WHITE BALANCE
function may become unstable.

Note

Digital Day/Night Vandal Resistant Dome Camera

Camera Operation

When there is a strong backlight behind the object, clear images of the
background as well as the object can still be obtained by using the
BACKLIGHT function.

1. Position the cursor to point to 'BACKLIGHT' on the SETUP menu by using

the UP and DOWN buttons.

2. Select the value required by pressing the LEFT or RIGHT button.

HIGH

: The gain increases from 0dB up to 42dB.

MIDDLE

: The gain increases from 0dB up to 30dB.

LOW

: The gain increases from 0dB up to 18dB.

OFF

: BACKLIGHT function does not operate.

BLC (Back Light Compensation)

SETUP

LENS

SHUTTER

---

WHITE BAL.

ATW

BACKLIGHT

OFF

AGC

LOW

DNR

MIDDLE

Digital Day/Night Vandal Resistant Dome Camera

1. Position the cursor to point to 'AGC' on the SETUP menu by using the

UP and DOWN buttons.

2. Select the value required by pressing the LEFT or RIGHT button. As the

level of gain increases the screen gets brighter but the level of noise will
also increase.

HIGH

: The gain varies between the range of 6dB ~ 42dB.

MIDDLE

: The gain varies between the range of 6dB ~ 30dB.

LOW

: The gain varies between the range of 6dB ~ 18dB.

OFF

: The gain is fixed at 6dB.

AGC (Auto Gain Control)

SETUP

LENS

SHUTTER

---

WHITE BAL.

ATW

BACKLIGHT

OFF

AGC

LOW
MIDDLE

DNR
SENS-UP

AUTO

SPECIAL
EXIT

Digital Day/Night Vandal Resistant Dome Camera

Camera Operation

The level of background noise in low light decreases automatically as the
level of gain changes.

1. Position the cursor to point to 'DNR' on the SETUP menu by using the

UP and DOWN buttons.

2. Select the value required by pressing the LEFT or RIGHT button.

OFF

: There is no reduction in noise level.

LOW

: There is a small reduction in noise level with almost no

ghost image.

MIDDLE

: The most effective mode. There is a sufficient reduction in

noise levels without causing significant ghosting.

HIGH

: The level of noise is reduced greatly, however there is an

increase in ghosting.

SENS UP helps maintain a bright, clear screen image by automatically
detecting changes in the level of light in low light level conditions.

DNR (Digital Noise Reduction)

SENS UP (Low Illuminance)

SETUP

LENS

SHUTTER

---

WHITE BAL.

ATW

BACKLIGHT

OFF

AGC

LOW

DNR

MIDDLE

SENS-UP

AUTO

SPECIAL

• When AGC is turned off, DNR does not operate.

Note

Digital Day/Night Vandal Resistant Dome Camera

1. Position the arrow to point to 'SENS UP' on the SETUP menu by using the

UP and DOWN buttons.

2. Select the value required by pressing the LEFT or RIGHT button.

AUTO

: Low light level automatic mode.

OFF

: The function does not operate.

3. Press the SET button when all the settings are complete.

SETUP

LENS

SHUTTER

---

WHITE BAL.

ATW

BACKLIGHT

OFF

AGC

LOW

DNR

MIDDLE

SENS-UP

AUTO

SPECIAL
EXIT

• When SHUTTER is in the manual or flk mode, SENS UP does not operate.
• When AGC is turned off, SENS UP does not operate.

Note

• The maximum storage magnification in low light level movement situations

can be adjusted by pressing the SET button in 'AUTO' mode.(X2~X128)

• As the magnification increases the screen gets brighter; however the after

image also increases.

• If storage magnification is increased while SENS UP is operational, it may

cause noise and spots may appear; this is normal.

Note

Digital Day/Night Vandal Resistant Dome Camera

Camera Operation

1. Position the cursor to point to 'SPECIAL' on the SETUP menu by using the

UP and DOWN buttons.

2. Select the mode required by pressing the UP or DOWN button.

CAMERA ID :

If an ID is input, this camera ID appears on the monitor

and recorded footage.

1) Position the cursor to point to ‘CAMERA ID’ by using the

UP or DOWN button.

2) Select 'ON' by pressing the LEFT or RIGHT button.

SPECIAL

• If 'OFF' is selected, the ID does not

appear on the monitor even if it has
been input.

Note

Digital Day/Night Vandal Resistant Dome Camera

•

If the wrong name has been input.....

Press the SET  button after moving the cursor to CLR and all the letters will be
erased.  If you want to correct a letter move the cursor to the arrow at the bottom
left of the screen and press 'SET'.
Position the cursor above the letter you wish to correct and then move the cursor
onto the letter you wish to choose and press the SET  button.

Note

3) Press the SET button.

4) Up to 15 characters can be used for the camera ID.

Move the cursor to the letter required by using the UP and DOWN button.

Select an ID from A,B~Y,Z, a,b~y,z, 0,1~8,9 by using the UP, DOWN,
LEFT and RIGHT buttons.
Lock in the characters by using the SET button.

• Once locked in the cursor moves to the next space in the ID.

Repeat the above steps until the ID is complete.

Digital Day/Night Vandal Resistant Dome Camera

Camera Operation

5) When the camera ID is complete, select a position for the name to be

displayed.

Move the cursor onto 'POS' and then press the SET button.

The ID will appear in the top left
corner.

Select the position where the ID is

to be displayed by using the 4 directional
buttons, and then press the SET button.

6) Select 'END' and press the SET button to complete ID input.

COLOUR

- AUTO : This camera has a function which automatically changes to

the appropriate mode dependant on lighting levels. COLOUR
mode is selected during daylight and B/W mode at night time.

- ON : The colour mode is selected by default, and the modes do

not change automatically.

Digital Day/Night Vandal Resistant Dome Camera

SYNC :

Two sychronisation modes are available, INTERNAL and

EXTERNAL LINE-LOCK. In LINE-LOCK mode, it synchronises the
video signal between cameras without a synchronous generator.
The line-lock synchronisation is only used in areas of 60Hz
(NTSC Models) / 50Hz (PAL Models).

- INT : Internal synchronisation
- LL : External line-lock synchronisation
• If ‘LL’ is selected, it can be adjusted to the desired phase.

Press the SET button.

• Adjust to the desired phase from 0 to 359.

• When the AGC is turned off, COLOUR does not operate.
• When an infrared light is used, there may be a problem with focusing.

Note

• When the mains frequency is 50Hz, the line-lock mode (NTSC Models) cannot be used.
• When the mains frequency is 60Hz, the line-lock mode (PAL Models) cannot be used.

Note

Digital Day/Night Vandal Resistant Dome Camera

Camera Operation

MOTION DETECTION:

This product has a feature that allows you to observe movements of objects
in 4 different areas on the screen, and the words 'MOTION DETECTED'
appear on the screen when movement is detected; hence a single individual
can conduct supervision efficiently. The camera detects an object's
movement by sensing disparity of outline, and level of brightness and colour.
• Press the SET button.

- OFF : MOTION DETECTION mode is cancelled.
- ON : Any motion in the selected areas is observed.

• Select the area for observation from the 4 areas in AREA SEL mode.
• Select the ON mode for the chosen area.
• Adjust the size of the area to be observed by using the UP, DOWN,

LEFT or RIGHT buttons.

• Please press the SET button to save the changes and complete the setting.

PRIVACY :

PRIVACY mode conceals areas on the screen.

- OFF : Cancels the PRIVACY mode. - ON : Turns On the PRIVACY mode.
• Press the SET button.

Digital Day/Night Vandal Resistant Dome Camera

• Select the area you do not wish to appear from the 4 areas in the

AREA SEL mode.

• Select ON mode for the chosen area.
• Adjust the size of the area to be concealed by using the UP, DOWN, LEFT

or RIGHT buttons.

MIRROR

- ON : Activates a horizontal image inversion.
- OFF : Cancels the inversion.

SHARPNESS :

The outline of the video image becomes cleaner and

more distinctive as the level of SHARPNESS increases. If the level goes
up excessively, however, it may affect the video image and generate noise.
• Press the SETUP button.

• The available range of level is 0 ~ 31.

RESET :

Returns to factory settings.

RETURN :

Saves the SPECIAL menu and returns to the SETUP menu.

Saves all the setting menus and then exits.

EXIT

Troubleshooting

If there are problems with the camera operation, check the tables below. If
the problem persists, please contact the agent who supplied the product.

Digital Day/Night Vandal Resistant Dome Camera

Problems

Nothing appears on the
screen.

The video image is not
clear.

The screen is dark.

There is a problem with
the camera operation.
The camera surface is
too hot and black stripes
appear on the screen.

• Check the power connection.
• Check the video signal line connection.

• Make sure that the lens is clean.

Clean the lens with a clean lint free cloth or

brush.

• Adjust the contrast control on the monitor.
• Make sure that the screen is not exposed

directly to a bright light.
Re-position the camera if necessary.

• Adjust the contrast control of the monitor.
• If there is an intermediate device, set the75ohm

Hi-z correctly, and also check the connections.

• If necessary, adjust the brightness level.

• Check if an appropriate power source to

the camera complies with the manufacturer's

standard requirement, or if the voltage is

fluctuating. Check for ground loops.

Troubleshooting

Digital Day/Night Vandal Resistant Dome Camera

Problems

The MOTION
DETECTION function is
not working.

Colours are not quite
right.

The screen is
flickering.

L/L mode isn't able to
be selected.

L/L mode is not
available.

COLOUR mode is not
working.

SENS-UP function is not
working.

• Check if 'MOTION DETECTION' mode is

turned on.

• Check the setting of the MD AREA.

• Check the 'WHITE BAL' setting.

(Please refer to page 19)

• Check if the camera is facing directly into

sunlight or fluorescent light.

• Have you connected your camera to DC power

source? Connect it to AC power source.

• Check the frequency of power supply

(60Hz for NTSC, 50Hz for PAL).

• Check if the AGC menu is set to the OFF

position.

• Check if the AGC menu is set to the OFF

position. AGC MUST be switched ON.

• Check if the SHUTTER menu is set to

MANUAL mode.

Troubleshooting

Digital Day/Night Vandal Resistant Dome Camera

Specifications

ITEM

Power Source

Total Pixels
Effective Pixels
Size
Scanning System

Synchronisation

Frequency
Resolution
Video Output
S/N (Y signal)
Min. Illumination
Colour
Gain Control
White Balance
Electronic Shutter Speed
Sens-Up
O.S.D
Motion Detection
DNR
Mirror
Privacy Function

C
C
D

AC24V / DC12V DC12V AC24V / DC12V DC12V

170mA(AC24V) / 250mA(DC12V) 160mA 170mA(AC24V) / 250mA(DC12V) 160mA

811(H) x 508(V) 795(H) x 596(V)

768(H) x 494(V) 752(H) x 582(V)

1/ 3 inch interline transfer CCD

2:1 Interlace

INT/LL Selectable

INT

INT/LL Selectable

INT

0~359

(Adjustable)

0~359

(Adjustable)

Horizontal:15.734 KHz Vertical :59.94 Hz Horizontal: 15.625 KHz Vertical : 50.00 Hz

540 TV Lines

1.0Vp-p / 75 (Video 0.714Vp-p Sync 0.286Vp-p) 1.0Vp-p / 75 (Video 0.7 Vp-p Sync 0.3 Vp-p)

50dB (AGC Off)

0.3Lux(Colour), 0.002Lux(Sense-upX128)

ON / AUTO

OFF / LOW / MIDDLE / HIGH

ATW / AWC / MANUAL (1,800

K~10,500

AUTO / MANUAL (1/60~1/120,000) AUTO / MANUAL (1/50~1/120,000)

OFF / AUTO

Built-in

ON / OFF (4 Programmable Zone)

OFF / LOW / MIDDLE / HIGH (Noise Reduction)

Built-in (Horizontal Image Inversion)

ON / OFF (4 Programmable Zone)

- 10

C ~ +50

C / 30~90% RH

1,100g

NTSC

PAL

Operating Temperature / Humidity
Weight

※

OPTION

- Dual Voltage : VRCD-5351/DV

- Heater : VRCD-5351H

- Colour : VRCD-5351/W

Model : VRCD-5351

Digital Day/Night

Vandal Resistant

Dome Camera

Instruction Guide

GENIE CCTV LTD.

CCTV House, City Park, Watchmead, Welwyn Garden City, Hertfordshire, AL7 ILT

Tel : +44 (0) 1707 330541 Fax : +44 (0) 1707 330543

www.geniecctv.com

Ask a Question ?