Genexis DRG700 Quick Installation Manual - User Manual

Download PDF User Manual

Full Text Searchable PDF User Manual

Quick Installation Guide

DRG700

This guide applies to all DRG700 models

Contents

DRG700 overview............................

2. Installation......................................

Network setup.................................

Wireless setup.................................

Configuring your DRG700................

6. Troubleshooting..............................

1. DRG700 overview

User interfaces

Interface

Description

Power port

Ethernet LAN
ports

USB 2.0 port

Telephony ports

CATV connector

Reset button

WPS button

Note: Depending on your specific

product type, port configuration may

differ.

Cleaning instructions:

Your DRG700 product may be cleaned using a soft, dry cloth. For areas
of persistent dirt, a damp cloth may be used with mild detergent. Product
and LED logos may be damaged by using aggressive cleaning products or
ethanol-based cleaners - if in doubt do not clean near these logos. Under
no circumstances allow water or cleaning fluid to ingress the product, as
this may cause permanent damage and prevent correct operation.

Status feedback LEDS:

LED

Activity

Description

On (green)
On (red)
Blink (green)
Off

Power on
Error
Booting
Power off

On
Off

WAN link active
WAN link inactive

On (green)
On (red)
Off

CATV on, signal received
CATV on, no signal received
CATV disabled

On
Off

Phone line 1 active
Phone line 1 inactive

On
Off

Phone line 2 active
Phone line 2 inactive

On
Blink
Off

WLAN enabled
WPS active
WLAN disabled

LAN

ports

On (green)

On (orange)

Blink

Link operating at 1000
Mbps
Link operating at 100 or 10
Mbps
Activity

Reset button:

Function

Action

Restart

To restart DRG700 without erasing
the saved configuration:

1. Press the button for less than 5

seconds.

2. Release the button.

Factory
reset

To restart DRG700 with all configura-

tion data cleared and factory settings
restored:

1. Press the button for more than 5

seconds.

2. Release the button.

WPS button:

This button is used to automatically connect a
WPS-enabled wireless client to the DRG700. For
details about the connection procedure, see
“Wireless Setup” on page 8.

2. Installation

Step 1: Preparing the DRG FTU

Remove the dust cover from the DRG FTU.

Step 2: Preparing the DRG700

Remove the dust covers for the fiber connectors

on the DRG700.

Step 3: Mounting the DRG700 on the DRG FTU

Place the DRG700 on the FTU in such as way

that the tabs on side of DRG700 are aligned

with the cutouts on the FTU.

Gently slide the DRG700 upwards until the fiber

connectors connect firmly with the FTU.

Step 4: Powering the DRG700

Connect the 12V plug of the supplied adapter to the

DRG700 and connect the adapter to a power socket.

Result: The LED first flashes green. When the

booting process is completed, the LED will be

solid green.

Note: The complete start-up sequence may take 2-3

minutes.

Step 5: Connecting your computer

Connect your computer to one of the Ethernet LAN

ports on the DRG700 using an Ethernet cable with a

RJ-45 connector.

Result: The LAN port LED is on (provided that the

computer is on).

Step 6: Connecting your telephone

This step is only relevant if the DRG700 has

telephony ports.

Connect a standard telephone handset a telephony

port using a RJ-11 cable.

Result: The

LED is on if voice is enabled

and operating correctly. You should hear a dialtone if

you pick up the handset.

Step 7: Connecting your analog television

This step is only relevant if the DRG700 has a CATV

connector.

Connect your television to the CATV connector using

a coaxial cable with a male F-connector.

Result: The LED is on if CATV is enabled and

operating correctly. You may need to retune your

television if required for the CATV service.

3. Network setup

Step 1:

Open your web browser and check if your Internet

connection is working. If your connection is working,

you may skip step 2 and 3.

Step 2:

(The following instructions are only for Windows

Windows 7 / Windows 8. For network setup

instructions on other operating systems, please

consult the user manual.)

Select Start > Control Panel.

In the Network and Internet section, click View

Network Status and Tasks.

Open the panel for network connections:

•

For Windows Vista: Click Manage network

connections at the top left hand corner.

•

For Windows 7: Click Change adapter

settings at the top left hand corner.

Identify the connected network card, right-click

the corresponding Local Area Connection, and

select Properties in the context menu.

Select Internet Protocol Version 4 (TCP/IPv4)

from the list and click Properties.

Select Obtain an IP address automatically and

Obtain DNS server address automatically.

Click OK and close the window.

Step 3:

Open your web browser and check if the network

connection is working. If your connection is not

working, refer to the Troubleshooting section on

page 11.

4. Wireless setup

This section is only relevant if wireless functionality

is available on your DRG700.

(The following instructions are only for Windows 7 /

Windows 8. For wireless setup instructions on other

operating systems, please consult the user manual.)

Wireless setup using WPA encryption key

Step 1:

Click the network icon in the notification area of the

taskbar. For example:

Step 2:

Select your network SSID and click Connect. The SSID

is the name of the wireless network.

Step 3:

Enter your WPA key and click OK. The WPA key is

the password needed for your secured wireless

network.

Note: You can find the default SSID and the WPA

key on a label shipped with the unit. They are also

printed on the label on the back of the DRG700.

You can change the SSID and the WPA key when you

configure the DRG700.

Wireless setup using WPS

Step 1:

Click the network icon in the notification area of the

taskbar.

Step 2:

Select your network SSID and click Connect.

Step 3:

Press the WPS button on the DRG.

The DRG700 automatically connects to the

computer. The connection is established and is

displayed as “Connected“ in the network list.

Toggling WLAN status

Press the WPS button for >5 seconds and release it.
All user-defined WLAN interfaces are toggled on/
off. Status is indicated by WLAN LED.

5. Configuring your DRG700

It is only advised for advanced users to change

the configuration, as doing this might interrupt

your connection. By default the router is

configured properly for most home networks.

Note: For information about how to reset the router

to the factory default settings, see “Reset button” on

page 3.

Requirements:

The configuration program has been tested on the

following browsers:

•

Safari version 5 or later

•

Firefox version 10 or later

•

Internet Explorer version 7.0 or later

•

Google Chrome

The browser must support Javascript.

Step 1:

Launch the web browser on your computer and

enter “http://router” in the address bar. The

router’s default IP address is “192.168.1.254”.

Step 2:

“admin”.

It is strongly advised to change the password

after you logged in for the first time.

Step 3:

Configure the router to the desired configuration.
Read the help text for additional information about
the settings.

6. Troubleshooting

Issue

Action

LED is off

Make sure you have connected the DRG700 to a working power outlet,

using the adapter shipped along with the DRG700. If the LED remains off,

please contact your service provider.

Red LED is on

System error. Disconnect the power from the DRG700 and restart

DRG700. If the problem persists, please contact your service provider.

LED is off

No uplink. Power down the device, wait for 1 minute, then power the de-

vice back on. If the problem persists, please contact your service provider.

LED is off

CATV is disabled. Please contact your service provider if a CATV signal is

expected.

Red LED is on

CATV is enabled but no signal is detected. Please contact your service

provider if a CATV signal is expected.

LED is off

Voice functionality is not enabled. Please contact your service provider if

voice functionality is expected.

LED is off

Please check in the web interface whether wireless functionality is

enabled. If the problem persists, please contact your service provider.

Web interface is not reachable

Check if the physical connection between the DRG700 and your computer

is correct.

Europe-EU Declaration of Conformity

Hereby, Genexis BV declares that this product is in compliance
with the essential requirements and other relevant provisions
of Directive 1999/5/EC.

Ask a Question ?